Broadcast address

Last updated

A broadcast address is a network address used to transmit to all devices connected to a multiple-access communications network. A message sent to a broadcast address may be received by all network-attached hosts.

Contents

In contrast, a multicast address is used to address a specific group of devices, and a unicast address is used to address a single device.

For network layer communications, a broadcast address may be a specific IP address. At the data link layer on Ethernet networks, it is a specific MAC address.

IP networking

In Internet Protocol version 4 (IPv4) networks, broadcast addresses are special values in the host-identification part of an IP address. The all-ones value was established as the standard broadcast address for networks that support broadcast. [1] This method of using the all-ones address was first proposed by R. Gurwitz and R. Hinden in 1982. [2] The later introduction of subnets and Classless Inter-Domain Routing changed this slightly, so that the all-ones value becomes the local broadcast address and the all-ones host address of each subnet is that subnet's directed broadcast address. [3]

The directed broadcast address for any IPv4 host can be obtained by taking the bit complement (bitwise NOT) of the subnet mask and then performing a bitwise OR operation with the host's IP address. A shortcut to this process (for common masks using only 0 and 1 bit placements) is to simply take the host's IP address and set all bits in the host identifier portion of the address (any bit positions which hold a 0 in the subnet mask) to 1.

As shown in the example below, in order to calculate the directed broadcast address to transmit a packet to an entire IPv4 subnet using the private IP address space 172.16.0.0/12, which has the subnet mask 255.240.0.0, the broadcast address is calculated as 172.16.0.0 bitwise ORed with 0.15.255.255 = 172.31.255.255. Directed broadcasts always work within a subnet but, for security reasons, many routers disable the forwarding of these by default. [4]

Broadcast address derivation example
Network IP address breakdown for 172.16.0.0/12Binary formDot-decimal notation
In bold below is shown the host part (suffix) of the IP address, with the network address prefix being the non-bold bits to its left. To obtain the broadcast address, the host bits get set to all 1's, while the network address prefix bits remain intact.
1. Network IP address10101100.00010000.00000000.00000000172.16.0.0
2. Subnet mask (The /12 in the IP address in this case means only the left-most 12 bits are 1s, as shown here. This reserves the left 12 bits for the network address (prefix) and the right 32 - 12 = 20 bits for the host address (suffix).)11111111.11110000.00000000.00000000255.240.0.0
3. Bit bomplement (bitwise NOT) of the subnet mask00000000.00001111.11111111.111111110.15.255.255
4. Broadcast address (bitwise OR of 1. Network IP address and 3. Bit complement of the subnet mask. This makes the broadcast address the largest possible IP address (and host address, since the host address portion is all 1s) for any given network address.)10101100.00011111.11111111.11111111172.31.255.255

A special definition exists for the IP address 255.255.255.255. It is the broadcast address of the zero network or 0.0.0.0, which in Internet Protocol standards stands for this network, i.e. the local network. Transmission to this address is limited by definition, in that it is never forwarded by the routers connecting the local network to other networks. [5] [6]

IP broadcasts are used by BOOTP and DHCP clients to find and send requests to their respective servers.

Internet Protocol version 6 (IPv6) does not implement this method of broadcast, and therefore does not define broadcast addresses. Instead, IPv6 uses multicast addressing to the all-hosts multicast group. No IPv6 protocols are defined to use the all-hosts address, though; instead, they send and receive on particular link-local multicast addresses. This results in higher efficiency because network hosts can filter traffic based on multicast address and do not need to process all broadcasts or all-hosts multicasts.

Ethernet

Broadcast is possible also on the underlying data link layer in Ethernet networks. Frames are addressed to reach every computer on a given LAN segment if they are addressed to MAC address FF:FF:FF:FF:FF:FF. Ethernet frames that contain IP broadcast packages are usually sent to this address.

Ethernet broadcasts are used, among other purposes, by Address Resolution Protocol to resolve IP addresses to MAC addresses.

IPX networking

Internetwork Packet Exchange (IPX) allows broadcast. A packet with network number of FFFFFFFF is sent to all networks available. When the node number is specified as FFFFFFFFFFFF, the packet is intended to be received by all hosts in the network.

AppleTalk

The AppleTalk protocol allows broadcast. When the node ID is specified as 255, a packet is sent to all networks available. [7]

See also

Related Research Articles

The Dynamic Host Configuration Protocol (DHCP) is a network management protocol used on Internet Protocol (IP) networks for automatically assigning IP addresses and other communication parameters to devices connected to the network using a client–server architecture.

An Internet Protocol address is a numerical label such as 192.0.2.1 that is assigned to a device connected to a computer network that uses the Internet Protocol for communication. IP addresses serve two main functions: network interface identification, and location addressing.

<span class="mw-page-title-main">IPv4</span> Fourth version of the Internet Protocol

Internet Protocol version 4 (IPv4) is the first version of the Internet Protocol (IP) as a standalone specification. It is one of the core protocols of standards-based internetworking methods in the Internet and other packet-switched networks. IPv4 was the first version deployed for production on SATNET in 1982 and on the ARPANET in January 1983. It is still used to route most Internet traffic today, even with the ongoing deployment of Internet Protocol version 6 (IPv6), its successor.

<span class="mw-page-title-main">IPv6</span> Version 6 of the Internet Protocol

Internet Protocol version 6 (IPv6) is the most recent version of the Internet Protocol (IP), the communications protocol that provides an identification and location system for computers on networks and routes traffic across the Internet. IPv6 was developed by the Internet Engineering Task Force (IETF) to deal with the long-anticipated problem of IPv4 address exhaustion, and was intended to replace IPv4. In December 1998, IPv6 became a Draft Standard for the IETF, which subsequently ratified it as an Internet Standard on 14 July 2017.

The Internet Protocol (IP) is the network layer communications protocol in the Internet protocol suite for relaying datagrams across network boundaries. Its routing function enables internetworking, and essentially establishes the Internet.

In computer networking, the User Datagram Protocol (UDP) is one of the core communication protocols of the Internet protocol suite used to send messages to other hosts on an Internet Protocol (IP) network. Within an IP network, UDP does not require prior communication to set up communication channels or data paths.

Classless Inter-Domain Routing is a method for allocating IP addresses for IP routing. The Internet Engineering Task Force introduced CIDR in 1993 to replace the previous classful network addressing architecture on the Internet. Its goal was to slow the growth of routing tables on routers across the Internet, and to help slow the rapid exhaustion of IPv4 addresses.

A multicast address is a logical identifier for a group of hosts in a computer network that are available to process datagrams or frames intended to be multicast for a designated network service. Multicast addressing can be used in the link layer, such as Ethernet multicast, and at the internet layer for Internet Protocol Version 4 (IPv4) or Version 6 (IPv6) multicast.

Open Shortest Path First (OSPF) is a routing protocol for Internet Protocol (IP) networks. It uses a link state routing (LSR) algorithm and falls into the group of interior gateway protocols (IGPs), operating within a single autonomous system (AS).

The Address Resolution Protocol (ARP) is a communication protocol used for discovering the link layer address, such as a MAC address, associated with a given internet layer address, typically an IPv4 address. This mapping is a critical function in the Internet protocol suite. ARP was defined in 1982 by RFC 826, which is Internet Standard STD 37.

<span class="mw-page-title-main">Subnet</span> Logical subdivision of an IP network

A subnetwork, or subnet, is a logical subdivision of an IP network. The practice of dividing a network into two or more networks is called subnetting.

In Internet networking, a private network is a computer network that restricts access to it. Only devices, systems, and users with appropriate authorization and authentication can connect to a private network.

The Virtual Router Redundancy Protocol (VRRP) is a computer networking protocol that provides for automatic assignment of available Internet Protocol (IP) routers to participating hosts. This increases the availability and reliability of routing paths via automatic default gateway selections on an IP subnetwork.

The Neighbor Discovery Protocol (NDP), or simply Neighbor Discovery (ND), is a protocol of the Internet protocol suite used with Internet Protocol Version 6 (IPv6). It operates at the internet layer of the Internet model, and is responsible for gathering various information required for network communication, including the configuration of local connections and the domain name servers and gateways.

Multicast DNS (mDNS) is a computer networking protocol that resolves hostnames to IP addresses within small networks that do not include a local name server. It is a zero-configuration service, using essentially the same programming interfaces, packet formats and operating semantics as unicast Domain Name System (DNS). It was designed to work as either a stand-alone protocol or compatible with standard DNS servers. It uses IP multicast User Datagram Protocol (UDP) packets and is implemented by the Apple Bonjour and open-source Avahi software packages, included in most Linux distributions. Although the Windows 10 implementation was limited to discovering networked printers, subsequent releases resolved hostnames as well. mDNS can work in conjunction with DNS Service Discovery (DNS-SD), a companion zero-configuration networking technique specified separately in RFC 6763.

IP multicast is a method of sending Internet Protocol (IP) datagrams to a group of interested receivers in a single transmission. It is the IP-specific form of multicast and is used for streaming media and other network applications. It uses specially reserved multicast address blocks in IPv4 and IPv6.

<span class="mw-page-title-main">Broadcasting (networking)</span> Network messaging to multiple recipients simultaneously

In computer networking, telecommunication and information theory, broadcasting is a method of transferring a message to all recipients simultaneously. Broadcasting can be performed as a high-level operation in a program, for example, broadcasting in Message Passing Interface, or it may be a low-level networking operation, for example broadcasting on Ethernet.

In computer networking, a link-local address is a network address that is valid only for communications on a local link, i.e. within a subnetwork that a host is connected to. Link-local addresses are typically assigned automatically through a process known as link-local address autoconfiguration, also known as auto-IP, automatic private IP addressing, and stateless address autoconfiguration. While most link-local addresses are unicast, this is not necessarily the case; e.g. IPv6 addresses beginning with ff02:, and IPv4 addresses beginning with 224.0.0. are multicast addresses that are link-local.

<span class="mw-page-title-main">IPv6 address</span> Label to identify a network interface of a computer or other network node

An Internet Protocol version 6 address is a numeric label that is used to identify and locate a network interface of a computer or a network node participating in a computer network using IPv6. IP addresses are included in the packet header to indicate the source and the destination of each packet. The IP address of the destination is used to make decisions about routing IP packets to other networks.

A solicited-node multicast address is an IPv6 multicast address used by the Neighbor Discovery Protocol to determine the link layer address associated with a given IPv6 address, which is also used to check if an address is already being used by the local-link or not, through a process called DAD. The solicited-node multicast addresses are generated from the host's IPv6 unicast or anycast address, and each interface must have a solicited-node multicast address associated with it.

References

  1. ↑ J. Mogul (October 1984). BROADCASTING INTERNET DATAGRAMS. Network Working Group. doi: 10.17487/RFC0919 . STD 5. RFC 919.Internet Standard 5.
  2. ↑ Robert Gurwitz; Robert Hinden (September 1982). IP - Local Area Network Addressing Issues. IEN 212.
  3. ↑ J. Mogul (October 1984). BROADCASTING INTERNET DATAGRAMS IN THE PRESENCE OF SUBNETS. Network Working Group. doi: 10.17487/RFC0922 . STD 5. RFC 922.Internet Standard 5.
  4. ↑ "Enabling forwarding of directed broadcasts" . Retrieved 2023-12-07.
  5. ↑ Ed Harmoush (June 9, 2022). "Local Broadcast vs Directed Broadcast" . Retrieved 2023-12-07.
  6. ↑ "Local vs Directed Broadcasts" . Retrieved 2023-12-07.
  7. ↑ Introduction to AppleTalk (PDF), Apple Inc. , retrieved 2021-10-04
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.