Cable jetting is a technique to install cables in ducts.[1] It is commonly used to install cables with optical fibers in underground polyethylene ducts and is an alternative to pulling.
Traditionally, fibre optic cables were pulled through cable ducts in the same way as other cables, via a winch line. Every time the fibre passes a bend or undulation in the duct, the pulling force is multiplied by a friction-dependent factor (which can be reduced by using lubricant[2]). This means that the higher the local pulling force is, the more friction the cable will experience while being pulled against the internal duct wall. This "capstan effect" [3][4] leads to an exponential force build-up with pull distance, producing generally high pulling forces.
Jetting
Cable jetting is the process of blowing a cable through a duct while simultaneously pushing the cable into the duct. Compressed air is injected at the duct inlet and flows through the duct and along the cable at high speed. (Preferably, no suction pig is used at the cable head.) The high speed air propels the cable due to drag forces and pressure drop. The friction of the cable against the duct is reduced by the distributed airflow, and large forces that would generate high friction are avoided. Because of the expanding airflow, the air propelling forces are relatively small at the cable inlet and large at the air exhaust end of the duct. To compensate for this, an additional pushing force is applied to the cable by the jetting equipment. The pushing force, acting mainly near the cable inlet, combined with the airflow propelling forces, increases the maximum jetting distance considerably. Special lubricants have been developed for cable jetting to further reduce friction.[5]
Advantages of jetting compared to pulling
Longer installation distances can be reached
Installation distance less dependent on bends and undulations in duct
Forces exerted on the cable are lower
Easier use jet in tandem operation
The step of installing a winch rope is avoided
Equipment is needed only at one end of the duct route
In the 21st century the cable jetting technique is used worldwide, from small optical telecom cables (1.8mm diameter) in small microducts (3mm internal diameter) up to large copper telecom cables (35mm diameter) in large ducts (50mm internal diameter). Jetting is done with a pressure of the compressed air in the order of 10 bar. With the jetting technique distances per blow of 3.5km have been reached , while spliceless links of 12km have been reached by placing jetting equipment in tandem. It is possible to install 12km in one day with one small crew.
In mid 1990s the technique was also developed to install multiple smaller microducts, bundles, into a larger duct in one installation. This is called multi-ducting, microduct cabling, or bundle blowing. Each can hold a cable.
Another capability is to install a single cable or a bundle of small ducts into an occupied duct. The most expensive activity in installing a network is the need for civil works. Thus, re-using ducts occupied with one cable, leaving some space, is a tempting and often possible and cost-effective alternative.
History
The technique of installing flexible and lightweight fibre optic units using compressed air was developed during the 1980s by British Telecom.[6] This early version of jetting did not use additional pushing. True cable jetting was invented by Willem Griffioen of KPN Research in the late 1980s.[7] The necessary equipment was developed in cooperation with Plumettaz, Switzerland.[8]
Sources
Griffioen, W., "A new installation method for fibre optic cables in conduits", Proc. 37th IWCS, November 1988, page 172
Griffioen, W., "The installation of conventional fibre optic cables in conduits using the viscous flow of air", J. Lightwave Technol., Vol. 7, no. 2 (1989) 297
Griffioen, W., "Installation of optical cables in ducts", Plumettaz, PTT Research 1993 ( ISBN90-72125-37-1)
Griffioen, W., Plumettaz, G., "Current developments in cable-in-duct blowing techniques", Proc. 46th IWCS, November 1997, page 363-367
Griffioen, W., Plumettaz, G., "Current development in cable-in-duct blowing techniques" Proc. ANCIT Workshop (Eurescom), Torino, 30–31 March 1998
Griffioen, W., Greven, W., Pothof, T. "A new fiber optic life for old ducts", Proc. 51st IWCS, November 2002, page 244-250
Griffioen, W., Zandberg, S., Versteeg, P. M., Keijzer, M., "Blow Simulation Test to Measure coefficient of Friction between (Micro)Duct and cable", Proc. 54th IWCS, November 2005, page 413-420
Notes
↑ "Archived copy". www.plumettaz.ch. Archived from the original on 27 September 2007. Retrieved 12 January 2022.CS1 maint: archived copy as title (link)
The turbofan or fanjet is a type of airbreathing jet engine that is widely used in aircraft propulsion. The word "turbofan" is a portmanteau of "turbine" and "fan": the turbo portion refers to a gas turbine engine which achieves mechanical energy from combustion, and the fan, a ducted fan that uses the mechanical energy from the gas turbine to force air rearwards. Thus, whereas all the air taken in by a turbojet passes through the combustion chamber and turbines, in a turbofan some of that air bypasses these components. A turbofan thus can be thought of as a turbojet being used to drive a ducted fan, with both of these contributing to the thrust.
A dark fibre or unlit fibre is an unused optical fibre, available for use in fibre-optic communication. Dark fibre may be leased from a network service provider.
The bypass ratio (BPR) of a turbofan engine is the ratio between the mass flow rate of the bypass stream to the mass flow rate entering the core. A 10:1 bypass ratio, for example, means that 10 kg of air passes through the bypass duct for every 1 kg of air passing through the core.
A propelling nozzle is a nozzle that converts the internal energy of a working gas into propulsive force; it is the nozzle, which forms a jet, that separates a gas turbine, being gas generator, from a jet engine.
Wire rope is several strands of metal wire twisted into a helix forming a composite rope, in a pattern known as laid rope. Larger diameter wire rope consists of multiple strands of such laid rope in a pattern known as cable laid.
An optical fiber is a flexible, transparent fiber made by drawing glass (silica) or plastic to a diameter slightly thicker than that of a human hair. Optical fibers are used most often as a means to transmit light between the two ends of the fiber and find wide usage in fiber-optic communications, where they permit transmission over longer distances and at higher bandwidths than electrical cables. Fibers are used instead of metal wires because signals travel along them with less loss; in addition, fibers are immune to electromagnetic interference, a problem from which metal wires suffer. Fibers are also used for illumination and imaging, and are often wrapped in bundles so they may be used to carry light into, or images out of confined spaces, as in the case of a fiberscope. Specially designed fibers are also used for a variety of other applications, some of them being fiber optic sensors and fiber lasers.
Microducts are small ducts for the installation of small microduct fibre optic cables. They have a size ranging from typically 3 to 16 mm and are installed as bundles in larger ducts.
Ducts are conduits or passages used in heating, ventilation, and air conditioning (HVAC) to deliver and remove air. The needed airflows include, for example, supply air, return air, and exhaust air. Ducts commonly also deliver ventilation air as part of the supply air. As such, air ducts are one method of ensuring acceptable indoor air quality as well as thermal comfort.
Distributed temperature sensing systems (DTS) are optoelectronic devices which measure temperatures by means of optical fibres functioning as linear sensors. Temperatures are recorded along the optical sensor cable, thus not at points, but as a continuous profile. A high accuracy of temperature determination is achieved over great distances. Typically the DTS systems can locate the temperature to a spatial resolution of 1 m with accuracy to within ±1°C at a resolution of 0.01°C. Measurement distances of greater than 30 km can be monitored and some specialised systems can provide even tighter spatial resolutions.
Fiber-optic communication is a method of transmitting information from one place to another by sending pulses of infrared light through an optical fiber. The light is a form of carrier wave that is modulated to carry information. Fiber is preferred over electrical cabling when high bandwidth, long distance, or immunity to electromagnetic interference is required. This type of communication can transmit voice, video, and telemetry through local area networks or across long distances.
Pipe ramming is a trenchless method for installation of steel pipes and casings. Distances of 30 m or more and over 1,500 mm in diameter are common, although the method can be used for much longer and larger installations. The method is useful for pipe and casing installations under railway lines and roads, where other trenchless methods could cause subsidence or heaving. The majority of installations are horizontal, although the method can be used for vertical installations.
A centrifugal fan is a mechanical device for moving air or other gases in a direction at an angle to the incoming fluid. Centrifugal fans often contain a ducted housing to direct outgoing air in a specific direction or across a heat sink; such a fan is also called a blower, blower fan, or squirrel-cage fan. Tiny ones used in computers are sometimes called biscuit blowers. These fans move air from the rotating inlet of the fan to an outlet. They are typically used in ducted applications to either draw air through ductwork/heat exchanger, or push air through similar. impellers. Compared to standard axial fans, they can provide similar air movement from a smaller fan package, and overcome higher resistance in air streams.
A fiber-optic cable, also known as an optical-fiber cable, is an assembly similar to an electrical cable, but containing one or more optical fibers that are used to carry light. The optical fiber elements are typically individually coated with plastic layers and contained in a protective tube suitable for the environment where the cable is used. Different types of cable are used for different applications, for example, long distance telecommunication, or providing a high-speed data connection between different parts of a building.
An air sock is a textile or fabric duct used for draught-free air distribution and delivery of conditioned air as an alternative to traditional spiral or rectangular steel ducts with grilles and diffusers. Fabric ducts are usually cheaper in material cost by no use of additional diffusers, and quicker to install than conventional metal systems.
This article briefly describes the components and systems found in jet engines.
An airbreathing jet engine is a jet engine that emits a jet of hot exhaust gases formed from air that is forced into the engine by several stages of centrifugal, axial or ram compression, which is then heated and expanded through a nozzle. They are typically gas turbine engines. The majority of the mass flow through an airbreathing jet engine is provided by air taken from outside of the engine and heated internally, using energy stored in the form of fuel.
Optical attached cable (OPAC) is a type of fibre optic cable that is installed by being attached to a host conductor along overhead power lines. The attachment system varies and can include wrapping, lashing or clipping the fibre optic cable to the host. Installation is typically performed using a specialised piece of equipment that travels along the host conductor from pole to pole or tower to tower, wrapping, clipping or lashing the fibre optic cable in place. Different manufacturers have different systems and the installation equipment, cable designs and hardware are not interchangeable.
An electrical conduit is a tube used to protect and route electrical wiring in a building or structure. Electrical conduit may be made of metal, plastic, fiber, or fired clay. Most conduit is rigid, but flexible conduit is used for some purposes.
A cable blowing machine is a machine designed to fit fiber optic cables into telecommunication ducts and microducts with the use of compressed air or water.
Fiber to the office (FTTO) is an alternative cabling concept for local area network (LAN) network office environments. It combines passive elements and active mini-switches to provide end devices with Gigabit Ethernet. FTTO involves centralised optical fibre cabling techniques to create a combined backbone/horizontal channel; this channel is provided from the work areas to the centralised cross-connect or interconnect by allowing the use of pull-through cables or splices in the telecommunications room.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
