Corrective Optics Space Telescope Axial Replacement

Last updated
COSTAR on exhibit at the National Air and Space Museum COSTAR 2.png
COSTAR on exhibit at the National Air and Space Museum

The Corrective Optics Space Telescope Axial Replacement (COSTAR) is an optical correction instrument designed and built by NASA. It was created to correct the spherical aberration of the Hubble Space Telescope 's primary mirror, which incorrectly focused light upon the Faint Object Camera (FOC), Faint Object Spectrograph (FOS), and Goddard High Resolution Spectrograph (GHRS) instruments. [1]

Contents

It was flown via shuttle to the telescope in the servicing mission STS-61, on December 2, 1993, and successfully installed over a period of eleven days.

Origin

Once it had been identified in 1990 that the primary mirror in the recently launched Hubble Space Telescope (HST) was defective due to it having been ground to the wrong shape, engineers at NASA came under immense pressure to fix the problem. The incorrect shape of the mirror introduced severe spherical aberration, a flaw in which light reflecting off the edge of a mirror focuses on a different point from the light reflecting off its center. The effect of the flaw on scientific observations depended on the particular observation—the core of the aberrated point spread function was sharp enough to permit high-resolution observations of bright objects, and spectroscopy of point sources was affected only through a sensitivity loss. However, the loss of light to the large, out-of-focus halo severely reduced the usefulness of the telescope for faint objects or high-contrast imaging. This meant nearly all the cosmological programs were essentially impossible, since they required observation of exceptionally faint objects. [2]

Development

When launched, the HST carried five scientific instruments: the Wide Field and Planetary Camera (WFPC), Goddard High Resolution Spectrograph (GHRS), High Speed Photometer (HSP), Faint Object Camera (FOC) and the Faint Object Spectrograph (FOS). Since it was too difficult to bring the HST back to earth for repairs the engineers considered everything from replacing the telescope's secondary mirror by sending a spacewalking astronaut into the telescope's optical tube, to installing a circular shade around the opening of the tube, which would reduce the aperture and improving the focus by blocking out the outer regions of the primary mirror. [3] It was eventually determined that with the HST still in orbit that they could replace the WFPC with the improved Wide Field and Planetary Camera 2 which would incorporate corrective optics. [3] This left solutions still to be found for the remaining instruments. One potential option was to insert corrective optics, lenses or mirrors in the telescope tube between the primary mirror and the secondary reflector. However the tube was too narrow for even the smallest astronaut to slither down it, leading to a search for a means of inserting the required corrective components into the tube. [4]

A crisis meeting of the European Space Agency was held in Germany to discuss the issues with the HST. Among the attendees was James H. Crocker, a senior optical engineer at the Ball Aerospace Corporation. While taking a shower in his German hotel one morning he noticed that the showerhead travelled on a vertical rod and it could be clamped on the rod at different heights and angles. The maid had left the showerhead at the base of the rod and positioned flat against the wall, which meant it was taking up very little space until Crocker loosened the clamp and moved it to the position he wanted. The idea came to him that they could mount the required corrective components on such a device that would allow them to be inserted into the tube before being folded out on robotic arms to the required position to intercept the beams of light from the secondary mirror, correct and then focus them on the various scientific instruments. [4] Once back in America he explained his idea, which was immediately taken up by other engineers who began to develop what by 1990 had become the Corrective Optics Space Telescope Axial Replacement, or COSTAR. The budgeted cost of the COSTAR was US$50,000,000. [5] To fit the COSTAR system onto the telescope, one of the other instruments had to be removed, and astronomers selected the High Speed Photometer to be sacrificed, which was the least important of the four axial detectors. [2]

The final design which is the size of a telephone booth consisted of small correction mirrors radiating out horizontally out from an extendable tower. For the aperture of each instrument there are two mirrors, M1 and M2. M1 which is in the light path acts as a field mirror and is a simple sphere, while the correction of the spherical aberration is done by M2 which is not perfectly shaped and reflects the incident light unevenly. However, the deviations have been calculated so that they are exactly inverse to those of the main mirror. Thus, after being reflected and corrected by the two mirrors, the light is back in the correct form. This arrangement has the advantage that the corrected field is free of coma. [6] [7] A total of ten correction mirrors with diameters ranging in size from approximately 18 to 24 mm were used as the Faint Object Camera and Faint Object Spectrograph each had two apertures for each of their two measuring channels whereas the Goddard High Resolution Spectrograph only had one aperture for both of its channels. [5] The design was complicated by the need to ensure that the beams of light for the above instruments which were mounted at the end of the telescope tube missed the beams for the new WFPC 2 which was mounted on one side of the telescope tube. [4]

The COSTAR assembly COSTAR.png
The COSTAR assembly

In January 1991 Ball Aerospace Corp. was selected by NASA as the prime contractor to undertake the entire development, production and verification of COSTAR, a process which took 26 months. [5] To calculate the required corrections one team calculated the existing error by examining the still in situ tooling that was used to make the primary mirror, while another independent team calculated it using the distorted images that Hubble had transmitted. Both teams came to practically identical measurement results. The correction mirrors that were subsequently produced were then checked for errors by two independent teams. Once complete the entire COSTAR was then tested in the COSTAR Alignment System (CAS). To check for any error in the CAS the COSTAR was then mounted in the specially developed Hubble Opto-Mechanical Simulator (HOMS) which simulated the errors in the faulty primary mirror, to allow an end to end test and thus verification of the output image. The HOMS system was also tested by two independent groups (one from Ball Aerospace and the other from the Goddard Space Flight Center) using different test instruments. The European Space Agency also contributed to the verification process by providing an engineering model of the Faint Object Camera to provide additional verification. [5]

Installation

COSTAR replaced the High Speed Photometer during the first Hubble Servicing Mission in 1993. [8] The original WFPC was replaced by the WFPC 2 during the same mission. [4]

On 28 December 1993 the robotic arms were instructed by the Space Telescope Science Institute to deploy the mirrors into position. The resulting images confirmed that the COSTAR had corrected the spherical aberration in the primary mirror. [7]

Removal from service

Later instruments, installed after the HST's initial deployment, were designed with their own corrective optics. COSTAR was removed from HST in 2009 during the fifth servicing mission and replaced by the Cosmic Origins Spectrograph. It is now on display in the Smithsonian's National Air and Space Museum in Washington, DC. [9] [3]

Diagram

Figure 4 from the NASA report "A Strategy for Recovery" showing how the mirrors M1 and M2 intercept and correct the starlight COSTAR optics.png
Figure 4 from the NASA report "A Strategy for Recovery" showing how the mirrors M1 and M2 intercept and correct the starlight

Related Research Articles

<span class="mw-page-title-main">Hubble Space Telescope</span> NASA/ESA space telescope launched in 1990

The Hubble Space Telescope is a space telescope that was launched into low Earth orbit in 1990 and remains in operation. It was not the first space telescope, but it is one of the largest and most versatile, renowned both as a vital research tool and as a public relations boon for astronomy. The Hubble telescope is named after astronomer Edwin Hubble and is one of NASA's Great Observatories. The Space Telescope Science Institute (STScI) selects Hubble's targets and processes the resulting data, while the Goddard Space Flight Center (GSFC) controls the spacecraft.

<span class="mw-page-title-main">Space Telescope Science Institute</span> Science operations center operated by NASA

The Space Telescope Science Institute (STScI) is the science operations center for the Hubble Space Telescope (HST), science operations and mission operations center for the James Webb Space Telescope (JWST), and science operations center for the Nancy Grace Roman Space Telescope. STScI was established in 1981 as a community-based science center that is operated for NASA by the Association of Universities for Research in Astronomy (AURA). STScI's offices are located on the Johns Hopkins University Homewood Campus and in the Rotunda building in Baltimore, Maryland.

<span class="mw-page-title-main">Reflecting telescope</span> Telescopes which utilize curved mirrors to form an image

A reflecting telescope is a telescope that uses a single or a combination of curved mirrors that reflect light and form an image. The reflecting telescope was invented in the 17th century by Isaac Newton as an alternative to the refracting telescope which, at that time, was a design that suffered from severe chromatic aberration. Although reflecting telescopes produce other types of optical aberrations, it is a design that allows for very large diameter objectives. Almost all of the major telescopes used in astronomy research are reflectors. Many variant forms are in use and some employ extra optical elements to improve image quality or place the image in a mechanically advantageous position. Since reflecting telescopes use mirrors, the design is sometimes referred to as a catoptric telescope.

<span class="mw-page-title-main">James Webb Space Telescope</span> NASA/ESA/CSA space telescope launched in 2021

The James Webb Space Telescope (JWST) is a space telescope specifically designed to conduct infrared astronomy. Its high-resolution and high-sensitivity instruments allow it to view objects too old, distant, or faint for the Hubble Space Telescope. This enables investigations across many fields of astronomy and cosmology, such as observation of the first stars and the formation of the first galaxies, and detailed atmospheric characterization of potentially habitable exoplanets.

<span class="mw-page-title-main">STS-61</span> 1993 American crewed spaceflight to the Hubble Space Telescope

STS-61 was NASA's first Hubble Space Telescope servicing mission, and the fifth flight of the Space Shuttle Endeavour. The mission launched on December 2, 1993, from Kennedy Space Center (KSC) in Florida. The mission restored the spaceborne observatory's vision with the installation of a new main camera and a corrective optics package (COSTAR). This correction occurred more than three and a half years after the Hubble was launched aboard STS-31 in April 1990. The flight also brought instrument upgrades and new solar arrays to the telescope.

<span class="mw-page-title-main">STS-82</span> 1997 American crewed spaceflight to the Hubble Space Telescope

STS-82 was the 22nd flight of the Space Shuttle Discovery and the 82nd mission of the Space Shuttle program. It was NASA's second mission to service the Hubble Space Telescope, during which Discovery's crew repaired and upgraded the telescope's scientific instruments, increasing its research capabilities. Discovery launched from Kennedy Space Center, Florida, on February 11, 1997, returning to Earth on February 21, 1997, at Kennedy Space Center.

<span class="mw-page-title-main">Space Telescope Imaging Spectrograph</span> Instrument on the Hubble Space Telescope

The Space Telescope Imaging Spectrograph (STIS) is a spectrograph, also with a camera mode, installed on the Hubble Space Telescope. Aerospace engineer Bruce Woodgate of the Goddard Space Flight Center was the principal investigator and creator of the STIS. It operated continuously from 1997 until a power supply failure in August 2004. After repairs, it began operating again in 2009. The spectrograph has made many important observations, including the first spectrum of the atmosphere of an extrasolar planet, HD 209458b.

<span class="mw-page-title-main">Advanced Camera for Surveys</span> Installed on HST March 2002

The Advanced Camera for Surveys (ACS) is a third-generation axial instrument aboard the Hubble Space Telescope (HST). The initial design and scientific capabilities of ACS were defined by a team based at Johns Hopkins University. ACS was assembled and tested extensively at Ball Aerospace & Technologies Corp. and the Goddard Space Flight Center and underwent a final flight-ready verification at the Kennedy Space Center before integration in the cargo bay of the Columbia orbiter. It was launched on March 1, 2002, as part of Servicing Mission 3B (STS-109) and installed in HST on March 7, replacing the Faint Object Camera (FOC), the last original instrument. ACS cost US$86 million at that time.

<span class="mw-page-title-main">Faint Object Camera</span> Installed on HST from 1990 to 2002

The Faint Object Camera (FOC) was a camera installed on the Hubble Space Telescope from launch in 1990 until 2002. It was replaced by the Advanced Camera for Surveys. In December 1993, Hubble's vision was corrected on STS-61 by installing COSTARS, which corrected the problem with Hubble's mirror before it reached an instrument like FOC. Later instruments had this correction built in, which is why it was possible to later remove COSTARS itself and replace it with a new science instrument.

<span class="mw-page-title-main">Wide Field and Planetary Camera 2</span>

The Wide Field and Planetary Camera 2 (WFPC2) is a camera formerly installed on the Hubble Space Telescope. The camera was built by the Jet Propulsion Laboratory and is roughly the size of a baby grand piano. It was installed by servicing mission 1 (STS-61) in 1993, replacing the telescope's original Wide Field and Planetary Camera (WF/PC). WFPC2 was used to image the Hubble Deep Field in 1995, the Engraved Hourglass Nebula and Egg Nebula in 1996, and the Hubble Deep Field South in 1998. During STS-125, WFPC2 was removed and replaced with the Wide Field Camera 3 as part of the mission's first spacewalk on May 14, 2009. After returning to Earth, the camera was displayed briefly at the National Air and Space Museum and the Jet Propulsion Laboratory before returning to its final home at the Smithsonian's National Air and Space Museum.

<span class="mw-page-title-main">Faint Object Spectrograph</span>

The Faint Object Spectrograph (FOS) was a spectrograph installed on the Hubble Space Telescope. It was replaced by the Space Telescope Imaging Spectrograph in 1997, and is now on display in the National Air and Space Museum in Washington DC.

<span class="mw-page-title-main">Wide Field and Planetary Camera</span> Former instrument on the Hubble Space Telescope

The Wide Field/Planetary Camera (WFPC) was a camera installed on the Hubble Space Telescope launched in April 1990 and operated until December 1993. It was one of the instruments on Hubble at launch, but its functionality was severely impaired by the defects of the main mirror optics which afflicted the telescope. However, it produced uniquely valuable high resolution images of relatively bright astronomical objects, allowing for a number of discoveries to be made by HST even in its aberrated condition.

<span class="mw-page-title-main">High Speed Photometer</span> Scientific instrument on the Hubble Space Telescope

The High Speed Photometer (HSP) is a scientific instrument formerly installed on the Hubble Space Telescope. The HSP was designed to measure the brightness and polarity of rapidly varying celestial objects. It could observe in ultraviolet, visible light, and near infrared at a rate of one measurement per 10 microseconds. The design was novel in that despite being able to view through a variety of filters and apertures, it had no moving parts "except for electrons" as principal investigator Prof. Robert Bless was fond of saying. Filter and aperture selection was accomplished using image dissector tubes and the HST pointing system. It was functional from launch in 1990 until it was removed at the end of 1993, and it helped diagnose an issue with the Hubble's primary mirror.

<span class="mw-page-title-main">Space Telescope European Coordinating Facility</span>

The Space Telescope – European Coordinating Facility (ST-ECF) was an institution which provided a number of support and service functions primarily for European observers of the NASA/ESA Hubble Space Telescope (HST). It was established in 1984 by the European Space Agency (ESA) and the European Southern Observatory (ESO), and was located at the ESO headquarters in Garching bei München, Germany. The ST-ECF ceased operations on 31 December 2010.

<span class="mw-page-title-main">International Ultraviolet Explorer</span> Astronomical observatory satellite

International Ultraviolet Explorer, was the first space observatory primarily designed to take ultraviolet (UV) electromagnetic spectrum. The satellite was a collaborative project between NASA, the United Kingdom's Science and Engineering Research Council and the European Space Agency (ESA), formerly European Space Research Organisation (ESRO). The mission was first proposed in early 1964, by a group of scientists in the United Kingdom, and was launched on 26 January 1978 aboard a NASA Thor-Delta 2914 launch vehicle. The mission lifetime was initially set for 3 years, but in the end it lasted 18 years, with the satellite being shut down in 1996. The switch-off occurred for financial reasons, while the telescope was still functioning at near original efficiency.

<span class="mw-page-title-main">Cosmic Origins Spectrograph</span>

The Cosmic Origins Spectrograph (COS) is a science instrument that was installed on the Hubble Space Telescope during Servicing Mission 4 (STS-125) in May 2009. It is designed for ultraviolet (90–320 nm) spectroscopy of faint point sources with a resolving power of ≈1,550–24,000. Science goals include the study of the origins of large scale structure in the universe, the formation and evolution of galaxies, and the origin of stellar and planetary systems and the cold interstellar medium. COS was developed and built by the Center for Astrophysics and Space Astronomy (CASA-ARL) at the University of Colorado at Boulder and the Ball Aerospace and Technologies Corporation in Boulder, Colorado.

<span class="mw-page-title-main">Wide Field Camera 3</span> Astronomical camera on the Hubble Space Telescope

The Wide Field Camera 3 (WFC3) is the Hubble Space Telescope's last and most technologically advanced instrument to take images in the visible spectrum. It was installed as a replacement for the Wide Field and Planetary Camera 2 during the first spacewalk of Space Shuttle mission STS-125 on May 14, 2009.

Robert A. Woodruff is an American physicist who is known principally for having designed and worked on a wide variety of instruments for space telescopes. These include Skylab (1967–1970), Apollo–Soyuz (1970s), Galileo (~1980), SIRTF and MIPS (1970s-1990s), and Hubble Space Telescope instruments [1977–present] ; James Webb Space Telescope (1995–2000), Kepler space telescope (mid-1990s), TPF, and Destiny (2003–present). He has had one or more instruments flying continuously in space since the early 1970s.

<span class="mw-page-title-main">NIRSpec</span> Spectrograph on the James Webb Space Telescope

The NIRSpec is one of the four scientific instruments flown on the James Webb Space Telescope (JWST). The JWST is the follow-on mission to the Hubble Space Telescope (HST) and is developed to receive more information about the origins of the universe by observing infrared light from the first stars and galaxies. In comparison to HST, its instruments will allow looking further back in time and will study the so-called Dark Ages during which the universe was opaque, about 150 to 800 million years after the Big Bang.

The Venus Spectral Rocket Experiment (VeSpR) was a suborbital rocket telescope that collected data on the ultraviolet (UV) light that is being emitted from Venus's atmosphere, which can provide information about the history of water on Venus. Measurements of this type cannot be done using Earth-based telescopes because Earth's atmosphere absorbs most UV light before it reaches the ground.

References

  1. ↑ Crocker, James H. (1993). "Engineering the COSTAR". Optics & Photonics News. 4 (11): 22. Bibcode:1993OptPN...4...22C. doi:10.1364/OPN.4.11.000022.
  2. 1 2 Tatarewicz, Joseph N. (1998). "The Hubble Space Telescope Servicing Mission". In Mack, Pamela E. (ed.). From Engineering Science to Big Science. NASA History Series. NASA. p. 375. ISBN   978-0-16-049640-0. NASA SP-1998-4219.
  3. 1 2 3 Harwood, William (April 22, 2015). "How NASA fixed Hubble's flawed vision and reputation". CBS. Retrieved April 16, 2020.
  4. 1 2 3 4 Winchester, Simon (2018). Exactly: How Precision Engineers Created the Modern World. London: William Collins. pp. 245–250. ISBN   978-0-00-824176-6.
  5. 1 2 3 4 "NASA Facts – Corrective Optics Space Telescope Axial Replacement (COSTAR)" (PDF). Goddard Space Flight Center. June 1993. Retrieved April 24, 2020.
  6. ↑ Brown, R.A.; H.C. Ford (1990). Report of the HST Strategy Panel: A Strategy for Recovery (PDF) (Technical report). NASA. CR-187826. Retrieved April 24, 2020.
  7. 1 2 Jedrzejewski, RI; Hartig, G; Jakobsen, P; Ford, HC (1994). "In-orbit performance of the COSTAR-corrected Faint Object Camera" (PDF). Astrophysical Journal Letters. 435: L7–L10. Bibcode:1994ApJ...435L...7J. doi:10.1086/187581.
  8. ↑ "Corrective Optics Space Telescope Axial Replacement (COSTAR)" . Retrieved July 18, 2015.
  9. ↑ "Camera That Saved Hubble Now On Display". NPR. November 18, 2009.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.