Counter-electromotive force

Last updated

Counter-electromotive force (counter EMF, CEMF, back EMF), [1] is the electromotive force (EMF) manifesting as a voltage that opposes the change in current which induced it. CEMF is the EMF caused by electromagnetic induction.

Contents

Details

For example, the voltage appearing across an inductor or coil is due to a change in current which causes a change in the magnetic field within the coil, and therefore the self-induced voltage. [1] [2] The polarity of the voltage at every moment opposes that of the change in applied voltage, to keep the current constant. [1] [3]

The term back electromotive force is also commonly used to refer to the voltage that occurs in electric motors where there is relative motion between the armature and the magnetic field produced by the motor's field coils or permanent magnet field, thus also acting as a generator while running as a motor. This effect is not due to the motor's inductance, which generates a voltage in opposition to a changing current via Faraday's law, but a separate phenomenon. That is, the back-EMF is also due to inductance and Faraday's law, but occurs even when the motor current is not changing, and arises from the geometric considerations of an armature spinning in a magnetic field.

This voltage is in series with and opposes the original applied voltage and is called "back-electromotive force" (by Lenz's law). With a lower overall voltage across the motor's internal resistance as the motor turns faster, the current flowing into the motor decreases. [4] One practical application of this phenomenon is to indirectly measure motor speed and position, as the back-EMF is proportional to the rotational speed of the armature. [5]

In motor control and robotics, back-EMF often refers most specifically to actually using the voltage generated by a spinning motor to infer the speed of the motor's rotation, for use in better controlling the motor in specific ways. [6]

To observe the effect of back-EMF of a motor, one can perform this simple exercise: with an incandescent light on, cause a large motor such as a drill press, saw, air conditioner compressor, or vacuum cleaner to start. The light may dim briefly as the motor starts. When the armature is not turning (called locked rotor) there is no back-EMF and the motor's current draw is quite high. If the motor's starting current is high enough, it will pull the line voltage down enough to cause noticeable dimming of the light.

Related Research Articles

<span class="mw-page-title-main">Electromagnetic coil</span> Electrical component

An electromagnetic coil is an electrical conductor such as a wire in the shape of a coil. Electromagnetic coils are used in electrical engineering, in applications where electric currents interact with magnetic fields, in devices such as electric motors, generators, inductors, electromagnets, transformers, and sensor coils. Either an electric current is passed through the wire of the coil to generate a magnetic field, or conversely, an external time-varying magnetic field through the interior of the coil generates an EMF (voltage) in the conductor.

<span class="mw-page-title-main">Inductive coupling</span>

In electrical engineering, two conductors are said to be inductively coupled or magnetically coupled when they are configured in a way such that change in current through one wire induces a voltage across the ends of the other wire through electromagnetic induction. A changing current through the first wire creates a changing magnetic field around it by Ampere's circuital law. The changing magnetic field induces an electromotive force in the second wire by Faraday's law of induction. The amount of inductive coupling between two conductors is measured by their mutual inductance.

<span class="mw-page-title-main">Electromagnetic induction</span> Production of voltage by a varying magnetic field

Electromagnetic or magnetic induction is the production of an electromotive force (emf) across an electrical conductor in a changing magnetic field.

<span class="mw-page-title-main">Electromotive force</span> Electrical action produced by a non-electrical source

In electromagnetism and electronics, electromotive force is the electrical action produced by a non-electrical source, measured in volts. Devices called electrical transducers provide an emf by converting other forms of energy into electrical energy, such as batteries or generators. This energy conversion is achieved by physical forces applying physical work on electric charges. However, the term "electromotive force" is not actually a force. Volta's mistake of labeling it a "force" is a misnomer that persists as a historical relic.

<span class="mw-page-title-main">Electric motor</span> Machine that converts electrical energy into mechanical energy

An electric motor is an electrical machine that converts electrical energy into mechanical energy. Most electric motors operate through the interaction between the motor's magnetic field and electric current in a wire winding to generate force in the form of torque applied on the motor's shaft. An electric generator is mechanically identical to an electric motor, but operates with a reversed flow of power, converting mechanical energy into electrical energy.

<span class="mw-page-title-main">Electric generator</span> Device that converts other energy to electrical energy

In electricity generation, a generator is a device that converts motive power into electric power for use in an external circuit. Sources of mechanical energy include steam turbines, gas turbines, water turbines, internal combustion engines, wind turbines and even hand cranks. The first electromagnetic generator, the Faraday disk, was invented in 1831 by British scientist Michael Faraday. Generators provide nearly all of the power for electric power grids.

<span class="mw-page-title-main">Lenz's law</span> Electromagnetic opposition to change

Lenz's law states that the direction of the electric current induced in a conductor by a changing magnetic field is such that the magnetic field created by the induced current opposes changes in the initial magnetic field. It is named after physicist Emil Lenz, who formulated it in 1834.

<span class="mw-page-title-main">Alternator</span> Device converting mechanical into electrical energy

An alternator is an electrical generator that converts mechanical energy to electrical energy in the form of alternating current. For reasons of cost and simplicity, most alternators use a rotating magnetic field with a stationary armature. Occasionally, a linear alternator or a rotating armature with a stationary magnetic field is used. In principle, any AC electrical generator can be called an alternator, but usually the term refers to small rotating machines driven by automotive and other internal combustion engines.

<span class="mw-page-title-main">Electrodynamic suspension</span> Magnetic levitation by time-varying fields

Electrodynamic suspension (EDS) is a form of magnetic levitation in which there are conductors which are exposed to time-varying magnetic fields. This induces eddy currents in the conductors that creates a repulsive magnetic field which holds the two objects apart.

<span class="mw-page-title-main">Faraday's law of induction</span> Basic law of electromagnetism of magnetic fields inducing a potential difference

Faraday's law of induction is a basic law of electromagnetism predicting how a magnetic field will interact with an electric circuit to produce an electromotive force (emf)—a phenomenon known as electromagnetic induction. It is the fundamental operating principle of transformers, inductors, and many types of electrical motors, generators and solenoids.

<span class="mw-page-title-main">DC motor</span> Motor which works on direct current

A DC motor is any of a class of rotary electrical motors that converts direct current (DC) electrical energy into mechanical energy. The most common types rely on the forces produced by magnetic fields. Nearly all types of DC motors have some internal mechanism, either electromechanical or electronic, to periodically change the direction of current in part of the motor.

<span class="mw-page-title-main">Traction motor</span> Electric motor for vehicle propulsion

A traction motor is an electric motor used for propulsion of a vehicle, such as locomotives, electric or hydrogen vehicles, elevators or electric multiple unit.

<span class="mw-page-title-main">Faraday paradox</span> Apparent paradox with Faradays law of induction

The Faraday paradox or Faraday's paradox is any experiment in which Michael Faraday's law of electromagnetic induction appears to predict an incorrect result. The paradoxes fall into two classes:

<span class="mw-page-title-main">Armature (electrical)</span> Power-producing component of an electric machine

In electrical engineering, the armature is the winding of an electric machine which carries alternating current. The armature windings conduct AC even on DC machines, due to the commutator action or due to electronic commutation, as in brushless DC motors. The armature can be on either the rotor or the stator, depending on the type of electric machine.

<span class="mw-page-title-main">Universal motor</span>

The universal motor is a type of electric motor that can operate on either AC or DC power and uses an electromagnet as its stator to create its magnetic field. It is a commutated series-wound motor where the stator's field coils are connected in series with the rotor windings through a commutator. It is often referred to as an AC series motor. The universal motor is very similar to a DC series motor in construction, but is modified slightly to allow the motor to operate properly on AC power. This type of electric motor can operate well on AC because the current in both the field coils and the armature will alternate synchronously with the supply. Hence the resulting mechanical force will occur in a consistent direction of rotation, independent of the direction of applied voltage, but determined by the commutator and polarity of the field coils.

<span class="mw-page-title-main">Repulsion motor</span>

A repulsion motor is a type of electric motor which runs on alternating current (AC). It was formerly used as a traction motor for electric trains but has been superseded by other types of motors. Repulsion motors are classified as single phase motors.

A brushed DC electric motor is an internally commutated electric motor designed to be run from a direct current power source and utilizing an electric brush for contact.

<span class="mw-page-title-main">Dynamo</span> Electrical generator that produces direct current with the use of a commutator

A dynamo is an electrical generator that creates direct current using a commutator. Dynamos were the first electrical generators capable of delivering power for industry, and the foundation upon which many other later electric-power conversion devices were based, including the electric motor, the alternating-current alternator, and the rotary converter.

In electrical engineering, electric machine is a general term for machines using electromagnetic forces, such as electric motors, electric generators, and others. They are electromechanical energy converters: an electric motor converts electricity to mechanical power while an electric generator converts mechanical power to electricity. The moving parts in a machine can be rotating or linear. Besides motors and generators, a third category often included is transformers, which although they do not have any moving parts are also energy converters, changing the voltage level of an alternating current.

Perepiteia is claimed to be a new generator developed by the Canadian inventor Thane Heins. The device is named after the Greek word for peripety, a dramatic reversal of circumstances or turning point in a story. The device was quickly attributed the term "perpetual motion machine" by several media outlets. Due to the long history of hoaxes and failures of perpetual motion machines and the incompatibility of such a device with accepted principles of physics, Heins' claims about Perepiteia have been treated with considerable skepticism.

References

  1. 1 2 3 Graf, "counterelectromotive force", Dictionary of Electronics
  2. ↑ Griffiths, David Jeffery. (2012). Introduction to Electrodynamics (3rd ed.).
  3. ↑ "Self-Inductance," Naval Electrical Engineering Training Series, Module 02: Introduction to Alternating Current and Transformers. Archived 2006-04-20 at the Wayback Machine
  4. ↑ "Nuclear Power Fundamentals Training Manuals". DC Generators, Counter-Electromotive Force Archived 2007-09-29 at the Wayback Machine (CEMF), DC Equipment Terminology, Electrical Science Volume 2.
  5. ↑ "Back-EMF". Acroname.com. 2006-08-07. Retrieved 2010-02-07.
  6. ↑ "Back EMF Motion Feedback" Back EMF Motion Feedback [ permanent dead link ]
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.