| CWJ | |
|---|---|
 | |
| Role | Basic training glider |
| National origin | Poland |
| Manufacturer | ZASPL |
| Designer | Wacław Czerwiński and Władysław Jaworski |
| First flight | 1931 |
| Number built | 80-100 |
The Czerwiński and Jaworski CWJ was a basic training glider designed and flown in Poland in 1931. Between eighty and one hundred examples of it and an improved variant, the CWJ-bis Skaut, were built.
ZASPL, the Aviation Association of students of the Lwów Technical University, was the oldest aviation organization in Poland. Revived after World War I, by 1926 it had workshops in Lwów which began building the glider designs of ZASPL member Wacław Czerwiński. The successful Czerwiński CW III, a 1929 open frame introductory glider, had shown the utility of the type for basic training but it was expensive and ready for development. In response, Czerwiński and Władysław Jarworski designed the CWJ (a fusion of their initials) to fill the national gliding clubs' needs. [1]
The fuselage of the CWJ was essentially an uncovered pine Warren girder, though the rear part of the lower longeron or chord was upward-curved. The unprotected pilot's seat was forward of the wing on a pine fuselage box which reached back to about mid fuselage. The box also carried twin sprung landing skids. The CWJ's two part, twin spar wing was rectangular in plan. Mounted on the upper fuselage longeron, it was wire braced from above via an inverted-V cabane and from below to the lower longeron. [1] Short ailerons reached the tips. [2]
At the rear a broad fin occupied the gap between the upper and lower longerons and had a short, triangular extension above. An almost rectangular rudder ran upwards from the bottom of the fin, extending well above it. The tailplane, mounted on the upper longeron, was triangular in plan. It carried elevators which were rectangular apart from cut-outs for rudder movement. [2]
The CWJ first flew in October 1931, tow-launched by a car. [2] An improved version, the CWJ-bis Skaut (Scout) made its first flight on 3 August 1933 at Czerwony Kamień, the base of the Lwów Aeroclub Gliding School. It had a wing increased in span by 900 mm (35 in), a corresponding 11% increase in wing area and had washout at the wingtips which improved aileron response. The wire wing bracing of the CWJ was replaced by pairs of parallel struts and the fuselage box was strengthened. The empennage was also modified; the fin now had a triangular, rather than straight, leading edge and at some later time the top of the rudder was made almost semi-circular. Early tests showed the sought-after improvement in handling. [1] [3]
Shortly after its successful early tests, early orders from both the government and LOPP took the CWJ into production. Design drawings were also produced for amateur builders and some parts and materials were made available from ZAPL. According to Cynk about eighty examples of the CWJ and CWJ-bis were built in all, including about twenty of the latter, [1] though samalotypolskie.pl says that there were one hundred altogether, eighty of them CWJs. [2] [3] They were used by clubs across Poland and were easy to transport, tough, could be car-launched and were stable in flight though with limited performance. By about 1938 both variants had been retired, displaced by the newer, better performing Kocjan Czajka and Kocjan Wrona. [1] [2] [3]
Data fromGeneral J. Cynk, 1971, [1] Performance samolotypolskie.pl. [2]
General characteristics
Performance
The 1926 German RRG Prüfling of 1926 was a secondary training glider designed for club use. Plans were sold and it was built in Germany and across the world.
The Błażyński Polon was a competitor in the First Polish Glider Contest, held in the late summer of 1923. It was of advanced aerodynamical design, showed promise but was wrecked before the best winds arrived.
The Jach Żabuś was a Polish glider designed to compete in the 1923 First Polish Glider Contest. It lacked vertical flying surfaces, had an unusual control system and made only one short flight. Rebuilt with conventional tail and controls, it won the distance flown prize at the second contest, held in 1925.
The Czerwinski (1927) glider was a simple, open frame, monoplane glider built in Poland to spread enthusiasm for aviation.
The Czerwiński CW I,, was a Polish glider designed and built by a students' group. Its career was brief but it made the first generally recognized soaring flight in Poland, a strong refutation of the current idea that Polish topography was not suited to the sport.
The Czerwiński CW II,, was a Polish open frame glider. In 1929 it set a new national duration record and flew successfully until the end of 1931, when several major structural and aerodynamic modifications improved its performance. A simpler, lighter version, the CW III,, was designed and built in parallel with it and became Poland's first production glider.
The one-off, experimental Czerwiński CW IV was a Polish high performance glider and the nation's first two-seater. It set several national records and influenced later Polish designs.
The Czerwiński CW 5bis was a Polish high performance sailplane, produced and developed between 1933 and 1935. It set several national records, competed at both national and international level and remained a Polish gliding club mainstay until the outbreak of World War II.
The ITS-II was a Polish intermediate training glider. Only about five were built as it was soon outclassed by newer Polish aircraft but some were used until 1935. ITS-IIs were used in early training courses on air towing and another gave the first demonstration of glider aerobatics in Poland. It was also used to set one national record.
The Blaicher B.1 was a Polish glider first flown in 1934. It was intended to fill an intermediate trainer role, but offered no advance on existing aircraft and only the prototype was completed.
The Czerwiński CW 7 was a Polish aerobatic glider first flown in 1934. Despite a structural weakness that prevented inverted flight, a small batch of CW 7s were used by several aeroclubs until the start of World War II.
The Czerwiński CW 8 was a mid-1930s Polish open-frame basic training glider. Its design was advanced and its price low, but its stalling characteristics were too dangerous for beginners, so the thirty-plus examples completed were rapidly withdrawn from use. Two were subsequently modified, one with greater span and the other with a small engine.
The Czajka (transl. Lapwing) or Kocjan Czajka after its designer was a Polish secondary training glider which was in continuous production from 1931 to the start of World War II. More than 160 were completed in Warsztaty Szybowcowe in Warsaw.
The D.W.L. SG-21 Lwów was a Polish high performance sailplane built for the Polish government. Though both it and a development, the SG-28, were one-offs, they set several national records and led to the batch-produced Warsztaty Szybowcowe SG-3.
The Warsztaty Szybowcowe Wrona, or Kocjan Wrona after its designer, was the most numerous and widely used Polish pre-war primary glider.
The Warsztaty Szybowcowe Sroka, or Kocjan Sroka after its designer, was a Polish intermediate training glider. About sixty were built between 1934 and 1939.
The Warsztaty Szybowcowe Sokół was a 1930s Polish aerobatic sailplane. Ten were built and flown by Polish aeroclubs, participating in national and international events, until the outbreak of the Second World War.
The Naleszkiewicz-Nowotny NN 2 was a Polish primary glider first flown in 1931. An improved version followed in 1932 but only three were built in total.
The Jaworski WJ 3 was a Polish, low-cost primary glider first flown in 1936. It did not prove popular and only one was built.
The single-seat Kocjan Komar (Gnat) intermediate trainer, designed in 1932, was the leading and most produced sailplane in pre-war Poland. Production was resumed after World War II as the IS-B Komar and it remained in use until 1965.