Dynamic soaring

Last updated

Dynamic soaring is a flying technique used to gain energy by repeatedly crossing the boundary between air masses of different velocity. Such zones of wind gradient are generally found close to obstacles and close to the surface, so the technique is mainly of use to birds and operators of radio-controlled gliders, but glider pilots are sometimes able to soar dynamically in meteorological wind shears at higher altitudes.

Contents

Dynamic soaring is sometimes confused with slope soaring which is a technique for achieving elevation.

Basic mechanism

While different flight patterns can be employed in dynamic soaring, the simplest is a closed loop across the shear layer between two airmasses in relative movement, e.g. stationary air in a valley, and a layer of wind above the valley. The gain in speed can be explained in terms of airspeed and groundspeed:

The energy is extracted by using the velocity difference between the two airmasses to lift the flying object to a higher altitude (or to reverse the descent respectively) after the transfer between the airmasses.

Dynamic Soaring Loop Dynamic Soaring Animated Diagram.gif
Dynamic Soaring Loop

In practice, there is a turbulent mixing layer between the moving and stationary air mass. In addition, drag forces are continually slowing the plane. Since higher speed gives rise to higher drag forces, there is a maximum speed that can be attained. Typically around 10 times the windspeed for efficient glider designs.

When seabirds perform dynamic soaring, the wind gradients are much less pronounced, so the energy extraction is comparably smaller. Instead of flying in circles as glider pilots do, birds commonly execute a series of half circles in opposite directions, in a zigzag pattern. An initial climb though the gradient while facing into the wind causes it to gain airspeed. It then makes an 180° turn and dives back through the same gradient but in the downwind direction, which again causes it to gain airspeed. It then makes an 180° turn at low altitude, in the other direction, to face back up into the wind... and the cycle repeats. By repeating the manoeuvre over and over it can make progress laterally to the wind while maintaining its airspeed, which enables it to travel in a cross-wind direction indefinitely.

As drag is slowing the bird, dynamic soaring is a tradeoff between speed lost to drag, and speed gained by moving through the wind gradient. At some point, climbing higher carries no additional benefit, as the wind gradient lessens with altitude.

Birds

Waved albatross Phoebastria irrorata Phoebastria irrorata flying.jpg
Waved albatross Phoebastria irrorata

Albatrosses are particularly adept at exploiting these techniques and can travel thousands of miles using very little energy. Gulls and terns also exhibit this behaviour in flight. Birds that soar dynamically have a skeletal structure that allows them to lock their wings when they are soaring, to reduce muscle tension and effort.

Lord Rayleigh first described dynamic soaring in 1883 in the British journal Nature : [1]

...a bird without working his wings cannot, either in still air or in a uniform horizontal wind, maintain his level indefinitely. For a short time such maintenance is possible at the expense of an initial relative velocity, but this must soon be exhausted. Whenever therefore a bird pursues his course for some time without working his wings, we must conclude either
  1. that the course is not horizontal,
  2. that the wind is not horizontal, or
  3. that the wind is not uniform.
It is probable that the truth is usually represented by (1) or (2); but the question I wish to raise is whether the cause suggested by (3) may not sometimes come into operation.

The first case described above by Rayleigh is simple gliding flight, the second is static soaring (using thermals, lee waves or slope soaring), and the last is dynamic soaring. [2]

Manned aircraft

In his 1975 book Streckensegelflug (published in English in 1978 as Cross-Country Soaring by the Soaring Society of America), Helmut Reichmann describes a flight made by Ingo Renner in a Glasflügel H-301 Libelle glider over Tocumwal in Australia on 24 October 1974. On that day there was no wind at the surface, but above an inversion at 300 meters there was a strong wind of about 70 km/h (40 knots). Renner took a tow up to about 350 m from where he dived steeply downwind until he entered the still air; he then pulled a 180-degree turn (with high g) and climbed back up again. On passing through the inversion he re-encountered the 70 km/h wind, this time as a head-wind. The additional air-speed that this provided enabled him to recover his original height. By repeating this manoeuvre he successfully maintained his height for around 20 minutes without the existence of ascending air, although he was drifting rapidly downwind. In later flights in a Pik 20 sailplane, he refined the technique so that he was able to eliminate the downwind drift and even make headway into the wind.

Unmanned aircraft

The dynamic soaring technique is adapted in unmanned aerial vehicles for enhancing their performance under a thrust-off condition. This improves the endurance and range of the aircraft in austere conditions.[ clarification needed ]

Spacecraft

Dynamic soaring as a means to exceed the solar wind speed by exploiting differences in solar wind speed near the sun, the Earth and/or the heliopause. [3] [4]

Radio-controlled glider

Dynamic soaring with R/C glider near Idaho Falls, Idaho. Wind direction is from right to left. DynamicSoaringKepps.JPG
Dynamic soaring with R/C glider near Idaho Falls, Idaho. Wind direction is from right to left.

In the late 1990s, radio-controlled gliding awoke to the idea of dynamic soaring (a "discovery" largely credited to RC soaring luminary Joe Wurts). [5] Radio-controlled glider pilots perform dynamic soaring using the leeward side of ground features such as ridges, saddles, or even rows of trees. If the ridge faces the wind, and has a steep back (leeward) side, it can cause flow separation off the top of the hill, resulting in a layer of fast air moving over the top of a volume of stagnant or reverse-flow air behind the hill. The velocity gradient, or wind shear, can be much greater than those used by birds or full scale sailplanes. The higher gradient allows for correspondingly greater energy extraction, resulting in much higher speeds for the aircraft. Models repeatedly cross the shear layer by flying in a circular path, penetrating a fast-moving headwind after flying up the back side, turning to fly with the wind, diving down through the shear layer into the stagnant air, and turning again to fly back up the back side of the hill. The loads caused by rapid turning at high speed (the fastest models can pull over 100 Gs) require significant structural reinforcement in the fuselage and wing. Because of this, dynamic soaring models are commonly built using composite materials.

As of February 21, 2023, the highest reported ground speed for radio control dynamic soaring was 908kph or 564 mph (490 kn). [6] There is no official sanctioning organization that certifies speeds, so records are listed unofficially based on readings from radar guns, although analysis from video footage and other sources is also used. Lately, some models have begun carrying on-board telemetry and other instruments to record such things as acceleration, air speed, etc.

Related Research Articles

<span class="mw-page-title-main">Hang gliding</span> Unpowered glider air sport

Hang gliding is an air sport or recreational activity in which a pilot flies a light, non-motorised foot-launched heavier-than-air aircraft called a hang glider. Most modern hang gliders are made of an aluminium alloy or composite frame covered with synthetic sailcloth to form a wing. Typically the pilot is in a harness suspended from the airframe, and controls the aircraft by shifting body weight in opposition to a control frame.

<span class="mw-page-title-main">Wind tunnel</span> Machine used for studying the effects of air moving around objects

Wind tunnels are machines where an object is held stationary inside a tube, and air is blown around it to study the interaction between the object and the moving air. They are used to test the aerodynamic effects of aircraft, rockets, cars, and buildings. Different wind tunnels range in size from less than a foot across, to over 100 feet (30 m), and can have air that moves at speeds from a light breeze to hypersonic velocities.

<span class="mw-page-title-main">Flight</span> Process by which an object moves, through an atmosphere or beyond it

Flight or flying is the process by which an object moves through a space without contacting any planetary surface, either within an atmosphere or through the vacuum of outer space. This can be achieved by generating aerodynamic lift associated with gliding or propulsive thrust, aerostatically using buoyancy, or by ballistic movement.

<span class="mw-page-title-main">Variometer</span> Flight instrument which determines the aircrafts vertical velocity (rate of descent/climb)

In aviation, a variometer – also known as a rate of climb and descent indicator (RCDI), rate-of-climb indicator, vertical speed indicator (VSI), or vertical velocity indicator (VVI) – is one of the flight instruments in an aircraft used to inform the pilot of the rate of descent or climb. It can be calibrated in metres per second, feet per minute or knots, depending on country and type of aircraft. It is typically connected to the aircraft's external static pressure source.

<span class="mw-page-title-main">Wind shear</span> Difference in wind speed or direction over a short distance

Wind shear, sometimes referred to as wind gradient, is a difference in wind speed and/or direction over a relatively short distance in the atmosphere. Atmospheric wind shear is normally described as either vertical or horizontal wind shear. Vertical wind shear is a change in wind speed or direction with a change in altitude. Horizontal wind shear is a change in wind speed with a change in lateral position for a given altitude.

<span class="mw-page-title-main">Lift-to-drag ratio</span> Measure of aerodynamic efficiency

In aerodynamics, the lift-to-drag ratio is the lift generated by an aerodynamic body such as an aerofoil or aircraft, divided by the aerodynamic drag caused by moving through air. It describes the aerodynamic efficiency under given flight conditions. The L/D ratio for any given body will vary according to these flight conditions.

<span class="mw-page-title-main">Speed to fly</span>

Speed to fly is a principle used by soaring pilots when flying between sources of lift, usually thermals, ridge lift and wave. The aim is to maximize the average cross-country speed by optimizing the airspeed in both rising and sinking air. The optimal airspeed is independent of the wind speed, because the fastest average speed achievable through the airmass corresponds to the fastest achievable average groundspeed.

In common usage, wind gradient, more specifically wind speed gradient or wind velocity gradient, or alternatively shear wind, is the vertical component of the gradient of the mean horizontal wind speed in the lower atmosphere. It is the rate of increase of wind strength with unit increase in height above ground level. In metric units, it is often measured in units of meters per second of speed, per kilometer of height (m/s/km), which reduces inverse milliseconds (ms−1), a unit also used for shear rate.

<span class="mw-page-title-main">Lee wave</span> Atmospheric stationary oscillations

In meteorology, lee waves are atmospheric stationary waves. The most common form is mountain waves, which are atmospheric internal gravity waves. These were discovered in 1933 by two German glider pilots, Hans Deutschmann and Wolf Hirth, above the Giant Mountains. They are periodic changes of atmospheric pressure, temperature and orthometric height in a current of air caused by vertical displacement, for example orographic lift when the wind blows over a mountain or mountain range. They can also be caused by the surface wind blowing over an escarpment or plateau, or even by upper winds deflected over a thermal updraft or cloud street.

<span class="mw-page-title-main">Airspeed</span> Speed of an aircraft relative to the surrounding air

In aviation, airspeed is the speed of an aircraft relative to the air it is flying through. It is difficult to measure the exact airspeed of the aircraft, but other measures of airspeed, such as indicated airspeed and Mach number give useful information about the capabilities and limitations of airplane performance. The common measures of airspeed are:

<span class="mw-page-title-main">Ridge lift</span> Wind deflected upwards by an obstacle

Ridge lift is created when a wind strikes an obstacle, usually a mountain ridge or cliff, that is large and steep enough to deflect the wind upward.

<span class="mw-page-title-main">Planetary boundary layer</span> Lowest part of the atmosphere directly influenced by contact with the planetary surface

In meteorology, the planetary boundary layer (PBL), also known as the atmospheric boundary layer (ABL) or peplosphere, is the lowest part of the atmosphere and its behaviour is directly influenced by its contact with a planetary surface. On Earth it usually responds to changes in surface radiative forcing in an hour or less. In this layer physical quantities such as flow velocity, temperature, and moisture display rapid fluctuations (turbulence) and vertical mixing is strong. Above the PBL is the "free atmosphere", where the wind is approximately geostrophic, while within the PBL the wind is affected by surface drag and turns across the isobars.

In aviation, calibrated airspeed (CAS) is indicated airspeed corrected for instrument and position error.

<span class="mw-page-title-main">Pitot–static system</span> System of pressure-sensitive instruments used to determine an aircrafts speed, altitude, etc.

A pitot–static system is a system of pressure-sensitive instruments that is most often used in aviation to determine an aircraft's airspeed, Mach number, altitude, and altitude trend. A pitot–static system generally consists of a pitot tube, a static port, and the pitot–static instruments. Other instruments that might be connected are air data computers, flight data recorders, altitude encoders, cabin pressurization controllers, and various airspeed switches. Errors in pitot–static system readings can be extremely dangerous as the information obtained from the pitot static system, such as altitude, is potentially safety-critical. Several commercial airline disasters have been traced to a failure of the pitot–static system.

Gliding flight is heavier-than-air flight without the use of thrust; the term volplaning also refers to this mode of flight in animals. It is employed by gliding animals and by aircraft such as gliders. This mode of flight involves flying a significant distance horizontally compared to its descent and therefore can be distinguished from a mostly straight downward descent like a round parachute.

Lift is a meteorological phenomenon used as an energy source by soaring aircraft and soaring birds. The most common human application of lift is in sport and recreation. The three air sports that use soaring flight are: gliding, hang gliding and paragliding.

<span class="mw-page-title-main">Glider (sailplane)</span> Type of aircraft used in the sport of gliding

A glider or sailplane is a type of glider aircraft used in the leisure activity and sport of gliding. This unpowered aircraft can use naturally occurring currents of rising air in the atmosphere to gain altitude. Sailplanes are aerodynamically streamlined and so can fly a significant distance forward for a small decrease in altitude.

The drag curve or drag polar is the relationship between the drag on an aircraft and other variables, such as lift, the coefficient of lift, angle-of-attack or speed. It may be described by an equation or displayed as a graph. Drag may be expressed as actual drag or the coefficient of drag.

<span class="mw-page-title-main">Richmond Field</span> Airport

Richmond Field is a privately owned, public use airport located two nautical miles (4 km) southeast of the central business district of Gregory, a city in Livingston County, Michigan, United States.

Numerous accidents have occurred in the vicinity of thunderstorms due to the density of clouds. It is often said that the turbulence can be extreme enough inside a cumulonimbus to tear an aircraft into pieces, and even strong enough to hold a skydiver. However, this kind of accident is relatively rare. Moreover, the turbulence under a thunderstorm can be non-existent and is usually no more than moderate. Most thunderstorm-related crashes occur due to a stall close to the ground when the pilot gets caught by surprise by a thunderstorm-induced wind shift. Moreover, aircraft damage caused by thunderstorms is rarely in the form of structural failure due to turbulence but is typically less severe and the consequence of secondary effects of thunderstorms.

References

  1. Lord Rayleigh (5 April 1883) "The soaring of birds," Nature, vol. 27, no. 701, pages 534–535.
  2. Boslough, Mark B.E. (June 2002). "Autonomous Dynamic Soaring Platform for Distributed Mobile Sensor Arrays" (PDF). Sand Report. Sandia National Laboratories, Albuquerque, New Mexico. SAND2002-1896. Archived from the original (PDF) on 2006-09-23.
  3. Mcrae, Mike (6 December 2022). "'Dynamic Soaring' Trick Could Speed Spacecraft Across Interstellar Space". ScienceAlert . Retrieved 6 December 2022.
  4. Larrouturou, Mathias N.; Higgns, Andrew J.; Greason, Jeffrey K. (28 November 2022). "Dynamic soaring as a means to exceed the solar wind speed". Frontiers in Space Technologies. 3. arXiv: 2211.14643 . Bibcode:2022FrST....317442L. doi: 10.3389/frspt.2022.1017442 .
  5. Sorrel, Charlie (June 24, 2009). "Don't Blink: 392 MPH Glider Tears Through the Air". Wired via www.wired.com.
  6. "List of speed records". RCSpeeds.com. Retrieved February 25, 2023.