Graduation (scale)

Last updated
A ruler with two linear scales: the metric and imperial. It includes shorter minor graduations and longer major graduations. Ruler Figure.png
A ruler with two linear scales: the metric and imperial. It includes shorter minor graduations and longer major graduations.

A graduation is a marking used to indicate points on a visual scale, which can be present on a container, a measuring device, or the axes of a line plot, usually one of many along a line or curve, each in the form of short line segments perpendicular to the line or curve. Often, some of these line segments are longer and marked with a numeral, such as every fifth or tenth graduation. The scale itself can be linear (the graduations are spaced at a constant distance apart) or nonlinear.

Contents

Linear graduation of a scale occurs mainly (but not exclusively) on straight measuring devices, such as a rule or measuring tape, using units such as inches or millimetres.

Graduations can also be spaced at varying spatial intervals, such as when using a logarithmic, for instance on a measuring cup, can vary in scale due to the container's non-cylindrical shape.

Graduations along a curve

Circular graduations of a scale occur on a circular arc or limb of an instrument. In some cases, non-circular curves are graduated in instruments. A typical circular arc graduation is the division into angular measurements, such as degrees, minutes and seconds. These types of graduated markings are traditionally seen on devices ranging from compasses and clock faces to alidades found on such instruments as telescopes, theodolites, inclinometers, astrolabes, armillary spheres, and celestial spheres.

There can also be non-uniform graduations such as logarithmic or other scales such as seen on circular slide rules and graduated cylinders.

A slide rule. This is an example of a mathematical instrument with graduated logarithmic and log-log scales. Slide rule scales back.jpg
A slide rule. This is an example of a mathematical instrument with graduated logarithmic and log-log scales.
A half circle protractor graduated in degrees (180deg). Protractor Rapporteur Degrees V3.jpg
A half circle protractor graduated in degrees (180°).

Manufacture of graduations

Graduations can be placed on an instrument by etching, scribing or engraving, painting, printing or other means. For durability and accuracy, etched or scribed marks are usually preferable to surface coatings such as paints and inks. Markings can be a combination of both physical marks such as a scribed line and a paint or other marking material. For example, it is common for black ink or paint to fill the grooves cut in a scribed rule. Inexpensive plastic devices can be molded and painted or molded with two or more colors of plastic used. Some rather high-quality devices can be manufactured with plastic and reveal high-precision graduations.

Graduations traditionally have been scribed into an instrument by hand with a sharp, hard tool. [1] Later developments in devices such as dividing engines allowed the process to be automated with greater precision. Modern devices can be stamped, cut on a milling machine or with a CNC machine. In the case of stamping, the master has the precision built into itself and the stamped device is as accurate as the stamping process allows. Similarly, molding of plastic can be as precise as the mold process. With proper concern for such effects as thermal expansion or contraction and shrinkage, the precision can be very high.

US graduation style

The US graduation style of an instrument was a Federal standard for codes used by manufacturers to quickly determine which types of scales are marked on the instrument.

Machinists rule graduations [2]
Graduation No.FacesEdges
1front1/10″, 1/20″, 1/50″, 1/100″
1/12″, 1/24″, 1/48″
reverse1/16″, 1/32″, 1/64″
1/14″, 1/28″
2front1/10″, 1/20″, 1/50″, 1/100″
1/12″, 1/24″, 1/48″
reverse1/16″, 1/32″, 1/64″
1/8″
3front1/32″
1/64″
reverse1/10″
1/50″
4front1/32″
1/64″
reverse1/8″
1/16″
4-1front1/8″
1/16″
reverseSame as front face, but from opposite end
Same as front face, but from opposite end
5front1/32″
1/64″
reverse1/10″
1/100″
6-1front1/10″
1/50″
reversenot graduated
not graduated
6-2front1/10″
1/10″
reverse1/50″
1/50″
7front1/32″ (or 1/16″)
1/64″ (or 1/32″)
reverse1/16″ (or 1/64″)
1/100″
9front1/16″
1/32″
reverse1/64″
not graduated
10front1/32″
1/64″
reversenot graduated
not graduated
11front1/100″
1/64″
reversenot graduated
not graduated
12front1/50″
1/100″
reversenot graduated
not graduated
16front1/32″
1/64″
reverse1/50″
1/100″
M-1front1.0 mm
0.5 mm
reversenot graduated
not graduated
M-2front1.0 mm (or 1.0 and 0.5 mm)
1.0 mm (or 1.0 and 0.5 mm)
reverse1.0 mm
0.5 mm
ME-1front0.5 mm
1/64″
reversenot graduated
not graduated
ME-2front1.0 mm
1/64″ (or 1/32″ and 1/64″)
reverse1.0 mm (or 1.0 and 0.5 mm)
1/32″

Other commonly recognized styles are:[ citation needed ]

Suffix key:

See also

Related Research Articles

<span class="mw-page-title-main">Slide rule</span> Mechanical analog computer

A slide rule is a hand-operated mechanical calculator consisting of slidable rulers for evaluating mathematical operations such as multiplication, division, exponents, roots, logarithms, and trigonometry. It is one of the simplest analog computers.

<span class="mw-page-title-main">Dual in-line package</span> Type of electronic component package

In microelectronics, a dual in-line package is an electronic component package with a rectangular housing and two parallel rows of electrical connecting pins. The package may be through-hole mounted to a printed circuit board (PCB) or inserted in a socket. The dual-inline format was invented by Don Forbes, Rex Rice and Bryant Rogers at Fairchild R&D in 1964, when the restricted number of leads available on circular transistor-style packages became a limitation in the use of integrated circuits. Increasingly complex circuits required more signal and power supply leads ; eventually microprocessors and similar complex devices required more leads than could be put on a DIP package, leading to development of higher-density chip carriers. Furthermore, square and rectangular packages made it easier to route printed-circuit traces beneath the packages.

<span class="mw-page-title-main">Micrometer (device)</span> Tool for the precise measurement of a components length, width, and/or depth

A micrometer, sometimes known as a micrometer screw gauge, is a device incorporating a calibrated screw widely used for accurate measurement of components in mechanical engineering and machining as well as most mechanical trades, along with other metrological instruments such as dial, vernier, and digital calipers. Micrometers are usually, but not always, in the form of calipers. The spindle is a very accurately machined screw and the object to be measured is placed between the spindle and the anvil. The spindle is moved by turning the ratchet knob or thimble until the object to be measured is lightly touched by both the spindle and the anvil.

<span class="mw-page-title-main">Ruler</span> An instrument used to measure distances or to draw straight lines

A ruler, sometimes called a rule, scale or a line gauge, is an instrument used to make length measurements, whereby a user estimates a length by reading from a series of markings called "rules" along an edge of the device. Commonly the instrument is rigid and the edge itself is a straightedge, which additionally allows one to draw straight lines. Some rulers, such as cloth or paper tape measures, are non-rigid. Specialty rulers exist that have flexible edges that retain a chosen shape; these find use in sewing, arts, and crafts.

<span class="mw-page-title-main">Potentiometer</span> Type of resistor, usually with three terminals

A potentiometer is a three-terminal resistor with a sliding or rotating contact that forms an adjustable voltage divider. If only two terminals are used, one end and the wiper, it acts as a variable resistor or rheostat.

<span class="mw-page-title-main">Vernier scale</span> Auxiliary scale of a measurement device, used to increase precision

A vernier scalever-NEE-er) , named after Pierre Vernier, is a visual aid to take an accurate measurement reading between two graduation markings on a linear scale by using mechanical interpolation, thereby increasing resolution and reducing measurement uncertainty by using vernier acuity to reduce human estimation error. It may be found on many types of instrument measuring linear or angular quantities, but in particular on a vernier caliper, which measures lengths.

In elementary mathematics, a number line is a picture of a straight line that serves as spatial representation of numbers, usually graduated like a ruler with a particular origin point representing the number zero and evenly spaced marks in either direction representing integers, imagined to extend infinitely. The metaphorical association between numbers and points on the line links arithmetical operations on numbers to geometric relations between points, and provides a conceptual scaffold for learning mathematics.

<span class="mw-page-title-main">Alidade</span> Device that allows one to sight a distant object

An alidade or a turning board is a device that allows one to sight a distant object and use the line of sight to perform a task. This task can be, for example, to triangulate a scale map on site using a plane table drawing of intersecting lines in the direction of the object from two or more points or to measure the angle and horizontal distance to the object from some reference point's polar measurement. Angles measured can be horizontal, vertical or in any chosen plane.

<span class="mw-page-title-main">Tape measure</span> Flexible ruler used to measure size or distance

A tape measure or measuring tape is a flexible ruler used to measure length or distance.

<span class="mw-page-title-main">Combination square</span> Measuring and marking tool

A combination square is a multi-purpose measuring and marking tool used in metalworking, woodworking, and stonemasonry. It is composed of a rule and one or more interchangeable heads that can be attached to the rule. Other names for the tool include adjustable square, combo square, and sliding square.

<span class="mw-page-title-main">Goniometer</span> Angle measuring instrument

A goniometer is an instrument that either measures an angle or allows an object to be rotated to a precise angular position. The term goniometry derives from two Greek words, γωνία (gōnía) 'angle' and μέτρον (métron) 'measure'. The protractor is a commonly used type in the fields of mechanics, engineering, and geometry.

<span class="mw-page-title-main">Meterstick</span> Straightedge or folding ruler used to physically measure lengths

A meterstick, metrestick, or yardstick is either a straightedge or foldable ruler used to measure length, and is especially common in the construction industry. They are often made of wood or plastic, and often have metal or plastic joints so that they can be folded together. Normal length of a meterstick made for the international market is either one or two meters, while a yardstick made for the U.S. market is typically one yard long.

<span class="mw-page-title-main">Calipers</span> Tool used to measure dimensions of an object

Caliper(s) or calliper(s) are an instrument used to measure the dimensions of an object; namely, the diameter or depth of a hole. The word caliper comes from latin roots meaning precise pincer.

<span class="mw-page-title-main">Indicator (distance amplifying instrument)</span> Distance amplifying instrument

In various contexts of science, technology, and manufacturing, an indicator is any of various instruments used to accurately measure small distances and angles, and amplify them to make them more obvious. The name comes from the concept of indicating to the user that which their naked eye cannot discern; such as the presence, or exact quantity, of some small distance.

A scale ruler is a tool for measuring lengths and transferring measurements at a fixed ratio of length; two common examples are an architect's scale and engineer's scale. In scientific and engineering terminology, a device to measure linear distance and create proportional linear measurements is called a scale. A device for drawing straight lines is a straight edge or ruler. In common usage, both are referred to as a ruler.

A level staff, also called levelling rod, is a graduated wooden or aluminium rod, used with a levelling instrument to determine the difference in height between points or heights of points above a vertical datum. When used for stadiametric rangefinding, the level staff is called a stadia rod.

<span class="mw-page-title-main">Dividing engine</span>

A dividing engine is a device employed to mark graduations on measuring instruments.

<span class="mw-page-title-main">Transversal (instrument making)</span>

Transversals are a geometric construction on a scientific instrument to allow a graduation to be read to a finer degree of accuracy. Their use creates what is sometimes called a diagonal scale, an engineering measuring instrument which is composed of a set of parallel straight lines which are obliquely crossed by another set of straight lines. Diagonal scales are used to measure small fractions of the unit of measurement.

<span class="mw-page-title-main">Diameter tape</span> Measurement tool

A diameter tape (D-tape) is a measuring tape used to estimate the diameter of a cylinder object, typically the stem of a tree or pipe. A diameter tape has either metric or imperial measurements reduced by the value of π. This means the tape measures the diameter of the object. It is assumed that the cylinder object is a perfect circle. The diameter tape provides an approximation of diameter; most commonly used in dendrometry.

The Battenberg course indicator is a mechanical calculating device invented by Prince Louis of Battenberg in 1892 for taking station on other vessels whose range, bearing, course and speed are known. By extension, it has a range of other functions related to relative velocity calculations.

References

  1. Daumas, Maurice, Scientific Instruments of the Seventeenth and Eighteenth Centuries and Their Makers, Portman Books, London 1989 ISBN   978-0-7134-0727-3
  2. "Federal Specification GGG-R-791H, Rules, Measuring". July 19, 1994.