Heaving to

Last updated
Plan view of a sloop hove to. The jib is backed to windward, the mainsail is slightly eased, and the rudder is fixed in an attempt to turn into the wind (which is coming from the top of the diagram). Hove-to.svg
Plan view of a sloop hove to. The jib is backed to windward, the mainsail is slightly eased, and the rudder is fixed in an attempt to turn into the wind (which is coming from the top of the diagram).

In sailing, heaving to (to heave to and to be hove to) is a way of slowing a sailing vessel's forward progress, as well as fixing the helm and sail positions so that the vessel does not have to be steered. [1] It is commonly used for a "break"; this may be to wait for the tide before proceeding, or to wait out a strong or contrary wind. For a solo or shorthanded sailor it can provide time to go below deck, to attend to issues elsewhere on the boat or to take a meal break. [2] [3] Heaving to can make reefing a lot easier, especially in traditional vessels with several sails. [4] : 113  It is also used as a storm tactic. [5]

Contents

A sailing vessel that is hove to is still, for the purposes of the collision regulations, on a defined tack. Therefore, unless other considerations dictate differently, it is helpful to heave to on the starboard tack, in order to be a "stand-on vessel", as per the regulations. [4] : 327 

The term is also used in the context of vessels under power and refers to bringing the vessel to a complete stop. For example, in waters over which the United States has jurisdiction the Coast Guard may, under 14 U.S.C. §522, demand that a boat "heave to" in order to enforce federal laws. [6]

Hove to

A brig hove to. The fore and main courses are clewed up (to reduce the amount of load on the rig) and the main topsail is backed to take the way off the vessel. The opium clipper Lanrick.jpg
A brig hove to. The fore and main courses are clewed up (to reduce the amount of load on the rig) and the main topsail is backed to take the way off the vessel.

A sailing vessel is hove to when it is at or nearly at rest because the driving action from one or more sails is approximately balanced by the drive from the other(s). This always involves "backing" one or more sails, so that the wind is pressing against the forward side of the cloth, rather than the aft side as it normally would for the sail to drive the vessel forwards. [1] On a square rigged vessel with more than one mast, a number of options are available; these generally involve bracing round the square topsail on one or more masts to an aback position to counterbalance the sails that remain set in their normal position. [7] : 225–230  On a modern two-sailed sloop, there is only the jib and the mainsail. A cutter may have more than one headsail, and a ketch, yawl or schooner may have more than one sail on a boom. In what follows, the jibs and boomed sails on such craft can either be treated as one of each, or lowered for the purposes of reduced windage, heel or complexity when heaving to for any length of time. [8]

When a sloop is hove to, the jib is backed. This means that its windward sheet is tight holding the sail to windward. The mainsail sheet is often eased, or the mainsail reefed, to reduce forward movement, or "fore-reaching". The rudder is placed so that, should the boat make any forward movement, it will be turned into the wind, so as to prevent forward momentum building up. [9] In a centerboard boat the centerboard will be partially raised and the tiller held down hard. [10]

Heaving to

For a sloop sailing along normally, either of two maneuvers will render the sailboat to be hove to.

First, the jib can be literally heaved to windward, using the windward sheet and releasing the other. [5] [11] Then the rudder would be put across so as to turn gently towards the wind. Without the drive of the jib, and allowing time for momentum to die down, the sailboat will be unable to tack and will stop hove to. This method may be preferable when broad reaching or running before a strong wind in a heavy sea and the prospect of tacking through the wind in order to heave to may not appeal. Bearing away from the wind so that the headsail is blanketed by the mainsail can make it easier to haul in the windward sheet.

Alternatively, the vessel can simply be turned normally to tack through the wind, without freeing the jibsheet. [5] [1] [11] The mainsail should self-tack onto the other side, but the jib is held aback. Finally the rudder is put the other way, as if trying to tack back again. Without the drive of the jib, she cannot do this and will stop hove to. This method is fast to implement and is recommended by sail training bodies such as the RYA as a "quick stop" reaction to a man overboard emergency, for sailing boats that have an engine available for further maneuvers to approach and pick up the casualty. [12]

Finally, in either case, the tiller or wheel should be lashed so that the rudder cannot move again, and the mainsheet adjusted so that the boat lies with the wind ahead of the beam with minimal speed forward. Usually this involves easing the sheet slightly compared to a closehauled position, but depending on the relative sizes of the sails, the shape and configuration of the keel and rudder and the state of the wind and sea, each skipper will have to experiment. [8] [1] After this the boat can be left indefinitely, only keeping a lookout for other approaching vessels.

When hove to, the boat will heel, there will be some drift to leeward and some tendency to forereach, so adequate seaway must be allowed for. In rough weather, this leeway can actually leave a "slick" effect to windward, in which the waves are smaller than elsewhere. [8] This can make a rest or meal break a little more comfortable at times.

To come out from the hove-to position and get under way again, the tiller or wheel is unlashed and the windward jibsheet is released, hauling in the normal leeward one. Bearing off the wind using the rudder will get the boat moving and then she can be maneuvered onto any desired course. [9] It is important when choosing the tack, heaving to, and remaining hove to, in a confined space that adequate room is allowed for these maneuvers. [13]

Heaving to as a storm tactic

Heaving to has been used by a number of yachts to survive storm conditions (winds greater than Force 10, 48–55 knots, 89–102 km/h, 55–63 mph). [5] During the June 1994 Queen's Birthday Storm, [14] all yachts that hove to survived the storm. [15] This included Sabre, a 10.4 m (34 ft) steel cutter with two persons on board, which hove to in wind speeds averaging 80 knots for 6 hours with virtually no damage. [5] [16]

During the ill-fated 1979 Fastnet race, of 300 yachts, 158 chose to adopt storm tactics; 86 "lay ahull", whereby the yacht adopts a "beam on" attitude to the wind and waves; 46 ran before the wind under bare poles or trailing warps/sea anchors, and 26 hove to. 100 yachts suffered knock downs; 77 rolled (that is turtled) at least once. Not one of the hove to yachts were capsized (knocked down or turtled) or suffered any serious damage. [17] The "heave to" maneuver is described in the story of the first Golden Globe yacht race of 1968. [18]

See also

Related Research Articles

<span class="mw-page-title-main">Sailing</span> Propulsion of a vehicle by wind power

Sailing employs the wind—acting on sails, wingsails or kites—to propel a craft on the surface of the water, on ice (iceboat) or on land over a chosen course, which is often part of a larger plan of navigation.

<span class="mw-page-title-main">Sailboat</span> Boat propelled partly or entirely by sails

A sailboat or sailing boat is a boat propelled partly or entirely by sails and is smaller than a sailing ship. Distinctions in what constitutes a sailing boat and ship vary by region and maritime culture.

<span class="mw-page-title-main">Rig (sailing)</span> Description of the specific ways that a sailing craft is rigged

A sailing vessel's rig is its arrangement of masts, sails and rigging. Examples include a schooner rig, cutter rig, junk rig, etc. A rig may be broadly categorized as "fore-and-aft", "square", or a combination of both. Within the fore-and-aft category there is a variety of triangular and quadrilateral sail shapes. Spars or battens may be used to help shape a given kind of sail. Each rig may be described with a sail plan—formally, a drawing of a vessel, viewed from the side.

A jib is a triangular sail that sets ahead of the foremast of a sailing vessel. Its tack is fixed to the bowsprit, to the bows, or to the deck between the bowsprit and the foremost mast. Jibs and spinnakers are the two main types of headsails on a modern boat.

A tack is a nautical term both for the lower, windward corner of a sail and, separately, for the windward side of a sailing craft (side from which the wind is coming while under way—the starboard or port tack. Generally, a boat is on a starboard tack if the wind is coming over the starboard side of boat with sails on port side. Similarly, a boat is on a port tack if the wind is coming over the port side of boat. However, confusion can result when a boat is on a 'run', with the wind coming directly from astern and the mainsail and jib/genoa are on opposite sides of the vessel. Therefore, the windward side is defined as the side opposite to that on which the mainsail is being carried. On a starboard tack the mainsail is carried on the port side. On a port tack the mainsail is carried on the starboard side. It is the position of the mainsail that determines the tack.

<span class="mw-page-title-main">Jibe</span> Basic sailing maneuver, where ship turns its stern through the wind

A jibe (US) or gybe (Britain) is a sailing maneuver whereby a sailing vessel reaching downwind turns its stern through the wind, which then exerts its force from the opposite side of the vessel. Because the mainsail boom can swing across the cockpit quickly, jibes are potentially dangerous to person and rigging compared to tacking. Therefore, accidental jibes are to be avoided while the proper technique must be applied so as to control the maneuver. For square-rigged ships, this maneuver is called wearing ship.

<span class="mw-page-title-main">Staysail</span>

A staysail ("stays'l") is a fore-and-aft rigged sail whose luff can be affixed to a stay running forward from a mast to the deck, the bowsprit, or to another mast.

<span class="mw-page-title-main">Spinnaker</span> Sail designed for sailing off the wind

A spinnaker is a sail designed specifically for sailing off the wind on courses between a reach to downwind. Spinnakers are constructed of lightweight fabric, usually nylon, and are often brightly colored. They may be designed to perform best as either a reaching or a running spinnaker, by the shaping of the panels and seams. They are attached at only three points and said to be flown.

This glossary of nautical terms is an alphabetical listing of terms and expressions connected with ships, shipping, seamanship and navigation on water. Some remain current, while many date from the 17th to 19th centuries. The word nautical derives from the Latin nauticus, from Greek nautikos, from nautēs: "sailor", from naus: "ship".

<span class="mw-page-title-main">Tacking (sailing)</span> A sailing maneuver

Tacking or coming about is a sailing maneuver by which a sailing craft, whose next destination is into the wind, turns its bow toward and through the wind so that the direction from which the wind blows changes from one side of the boat to the other, allowing progress in the desired direction. Sailing vessels are unable to sail higher than a certain angle towards the wind, so "beating to windward" in a zig-zag fashion with a series of tacking maneuvers, allows a vessel to sail towards a destination that is closer to the wind that the vessel can sail directly.

<span class="mw-page-title-main">Model yachting</span>

Model yachting is the pastime of building and racing model yachts. It has always been customary for ship-builders to make a miniature model of the vessel under construction, which is in every respect a copy of the original on a small scale, whether steamship or sailing ship. There are fine collections to be seen at both general interest museums such as the Victoria and Albert Museum in London and at many specialized maritime museums worldwide. Many of these models are of exquisite workmanship, every rope, pulley or portion of the engine being faithfully reproduced. In the case of sailing yachts, these models were often pitted against each other on small bodies of water, and hence arose the modern pastime. It was soon seen that elaborate fittings and complicated rigging were a detriment to rapid handling, and that, on account of the comparatively stronger winds in which models were sailed, they needed a greater draught. For these reasons modern model yachts, which usually have fin keels, are of about 15% or 20% deeper draught than full-sized vessels, while rigging and fittings have been reduced to absolute simplicity. This applies to models built for racing and not to elaborate copies of steamers and ships, made only for show or for " toy cruising."

Rounding-up is a phenomenon that occurs in sailing when the helmsman is no longer able to control the direction of the boat and it heads up into the wind, causing the boat to slow down, stall out, or tack. This occurs when the wind overpowers the ability of the rudder to maintain a straight course.

A mast-aft rig is a sailboat sail-plan that uses a single mast set in the aft half of the hull. The mast supports fore-sails that may consist of a single jib, multiple staysails, or a crab claw sail. The mainsail is either small or completely absent. Mast-aft rigs are uncommon, but are found on a few custom, and production sailboats.

Weather helm is the tendency of sailing vessels to turn towards the source of wind, creating an unbalanced helm that requires pulling the tiller to windward in order to counteract the effect.

<span class="mw-page-title-main">Forces on sails</span>

Forces on sails result from movement of air that interacts with sails and gives them motive power for sailing craft, including sailing ships, sailboats, windsurfers, ice boats, and sail-powered land vehicles. Similar principles in a rotating frame of reference apply to windmill sails and wind turbine blades, which are also wind-driven. They are differentiated from forces on wings, and propeller blades, the actions of which are not adjusted to the wind. Kites also power certain sailing craft, but do not employ a mast to support the airfoil and are beyond the scope of this article.

<span class="mw-page-title-main">Tell-tale (sailing)</span>

A tell-tale, in a nautical or sailing context, is a piece of yarn or fabric attached to a sail, a stay, or any rigging on a sailboat. Typically, a tell-tale is on a port and a starboard stay.

The Marlow-Hunter 18 is an American sailing dinghy that was designed by Glenn Henderson as a day sailer and first built in 2011.

The Beachcomber 25 is an American trailerable sailboat that was designed by Walter Scott as a cruiser and first built in 1979.

The Stiletto 27 is an American trailerable catamaran sailboat that was designed by Bill Higgins and Don Ansley as a racer/cruiser and first built in 1976.

This glossary of nautical terms is an alphabetical listing of terms and expressions connected with ships, shipping, seamanship and navigation on water. Some remain current, while many date from the 17th to 19th centuries. The word nautical derives from the Latin nauticus, from Greek nautikos, from nautēs: "sailor", from naus: "ship".

References

  1. 1 2 3 4 Schell, Andy (21 January 2013). "Cruising Tips: Heaving-To". Sail Magazine. Retrieved 21 June 2017.
  2. ↑ www.sailingusa.info/points_of_sail.htm Archived June 26, 2006, at the Wayback Machine
  3. ↑ "Heavy weather conditions at sea (pictures and further explanation)" . Retrieved 17 April 2015.
  4. 1 2 Cunliffe, Tom (2016). Hand, Reef and Steer: Traditional Sailing Skills for Classic Boats (second ed.). Adlard Coles. ISBN   978-1472925220.
  5. 1 2 3 4 5 Bruce, Peter (2016). Heavy Weather Sailing (7th ed.). Bloomsbury. pp. 192–195. ISBN   9781472928207 . Retrieved 21 June 2017.
  6. ↑ "18 U.S. Code § 2237 - Criminal sanctions for failure to heave to, obstruction of boarding, or providing false information". LII / Legal Information Institute. Retrieved 2022-11-13.
  7. ↑ Harland, John (2015). Seamanship in the age of sail : an account of shiphandling of the sailing man-o-war, 1600-1860. London. ISBN   978-1-8448-6309-9.{{cite book}}: CS1 maint: location missing publisher (link)
  8. 1 2 3 Pardey, Lin (2008). Storm Tactics Handbook, 3rd Ed., Modern methods of heaving-to for survival in extreme conditions. Arcata, California: Pardey Books. pp. 44–48. ISBN   978-1-92921-447-1.
  9. 1 2 "Heaving To - Parking your boat without anchoring". Coastal Boating.net. Retrieved 21 June 2017.
  10. ↑ "Heaving to and the centerboard". The Trailorsailor. Retrieved 21 June 2017.
  11. 1 2 "How to manoeuvre under sail". How to cruise under sail - Safety and comfort for live-aboard, long-distance sailors. 23 June 2010. Retrieved 21 June 2017.
  12. ↑ Pearson, Malcolm (2007). Reeds skipper's handbook: for sail and power. London: Adlard Coles Nautical. p. 127. ISBN   978-0-7136-8338-7.
  13. ↑ Pardey 2008, p. 116.
  14. ↑ Bruce 2016, pp. 241–253.
  15. ↑ Bruce 2016, p. 248.
  16. ↑ Taylor, Kim (1996). The 1994 Pacific Storm Survey. Auckland, N.Z.: Captain Teach Press and Quarry Pub. p. 10. ISBN   1-877197-11-4. OCLC   154204736.
  17. ↑ Pardey 2008, p. 97.
  18. ↑ Nichols, Peter (2002). A Voyage For Madmen. London: Profile Books. p. 320. ISBN   978-1861974655.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.