High-speed multimedia radio

Last updated

High-speed multimedia radio (HSMM) is the implementation of high-speed wireless TCP/IP data networks over amateur radio frequency allocations using commercial off-the-shelf (COTS) hardware such as 802.11 Wi-Fi access points. This is possible because the 802.11 unlicensed frequency bands partially overlap with amateur radio bands and ISM bands in many countries. Only licensed amateur radio operators may legally use amplifiers and high-gain antennas within amateur radio frequencies to increase the power and coverage of an 802.11 signal.

Contents

A typical piece of equipment used for HSMM (Linksys WRT54G) Linksys WRT54G.jpg
A typical piece of equipment used for HSMM (Linksys WRT54G)

Basics

The idea behind this implementation is to modify commercial 802.11 equipment for use on licensed Amateur Radio frequencies. The main frequency bands being used for these networks are: 900 MHz (33 cm), 2.4 GHz (13 cm), 3.4 GHz (9 cm), and 5.8 GHz (5 cm). [1] [2] [3] [4] [5] Since the unlicensed 802.11 or Wi-Fi frequency bands overlap with amateur frequencies, only custom firmware is needed to access these licensed frequencies. Such networks can be used for emergency communications for disaster relief operations as well as in everyday amateur radio communications (hobby/social).

Capabilities

HSMM can support most of the traffic that the Internet currently does, including video chat, voice, instant messaging, email, the Web (HTTP), file transfer (FTP), and forums. The only differences being that with HSMM, such services are community instead of commercially implemented and it is mostly wireless. HSMM can even be connected to the Internet and used for web surfing, although because of the FCC regulations on permitted content, this is done only when directly used for ham radio activities (under Part 97). Using high gain directional antennas and amplifiers, reliable long-distance wireless links over many miles are possible and only limited by propagation and the radio horizon.

Bandwidths and Speeds

HSMM networks most-often use professional hardware with narrower channel bandwidths such as 5 or 10 MHz to help increase range. It is common for networks to use channel -2 with a 5 MHz bandwidth. For long-range links extending outside of metropolitan areas 802.11b DSSS modulations or 802.11ah (900 MHz) equipment can be used, further increasing range at the cost of speed.

US / FCC Frequencies and channels

The following is a list of the 802.11 channels that overlap into an amateur radio band under the FCC in the United States. Note that the 5 cm amateur band extends from 5.65 to 5.925 GHz, so that there are many frequencies outside the Part 15 ISM/UNII block used for 802.11a. Many commercial grade 802.11a access points can also operate in between the normal channels by using 5 MHz channel spacing instead of the standard 20 MHz channel spacing. 802.11a channels 132, 136 and 140 are only available for unlicensed use in ETSI regions. Channels and frequencies marked in red should not be used.

The following images show the overlapping relationship of the Part 15 unlicensed bands and the Part 97 licensed bands. The images are not to scale.

3.4 GHz 802.11b/g
Hsmmnet-freq-sharing-2.4.gif

5.8 GHz 802.11a
Hsmmnet-freq-sharing-5.8.gif

Acronyms Used: (amateur radio) (ISM) (Radar)

Channels and power

FCC / United States

802.11a

The 802.11a amateur radio band consists of 30 overlapping channels in the 5.650–5.925 GHz (5 cm) band. The 802.11a standard uses OFDM or "Orthogonal Frequency Division Multiplexing" to transmit data and therefore is not classified as spread-spectrum. Because of this 802.11a hardware is not subject to the power rules in FCC Part 97 § 97.311 and the maximum allowable output power is 1,500 watts (W) PEP.

802.11b

The 802.11b amateur radio band consists of 8 overlapping channels in the 2.390–2.450 GHz (13 cm) band. The 802.11b specification uses Direct Sequence Spread Spectrum (DSSS) to transmit data and is subject to the rules of FCC Part 97 § 97.311. Therefore, the maximum allowable power output in the USA is 10 W PEP.

802.11g

The 802.11g amateur radio band consists of 8 overlapping channels in the 2.4 GHz (13 cm) band. The 802.11g standard uses OFDM or "Orthogonal Frequency Division Multiplexing" to transmit data and therefore is not classified as spread-spectrum. Because of this 802.11g hardware is not subject to the power rules in FCC Part 97 § 97.311 and the maximum allowable output power is 1,500 W PEP.

802.11n

The 802.11n amateur radio band consists of 8 overlapping channels in the 2.4 GHz (13 cm) band. The 802.11n standard uses OFDM or "Orthogonal Frequency Division Multiplexing" to transmit data and therefore is not classified as spread-spectrum. Because of this 802.11n hardware is not subject to the power rules in FCC Part 97 § 97.311 and the maximum allowable output power is 1,500 W PEP.

802.11y

The 802.11y amateur radio band consists of 24 overlapping channels in the 3.4 GHz (9 cm) band. The 802.11y standard uses OFDM or "Orthogonal Frequency Division Multiplexing" to transmit data and therefore is not classified as spread-spectrum. Because of this 802.11y hardware is not subject to the power rules in FCC Part 97 § 97.311 and the maximum allowable output power is 1,500 W PEP.

Frequency sharing

FCC / United States

802.11a

The 5 cm band is shared with the fixed-satellite service in ITU Region 1, and the radiolocation service. In ITU Region 2 (US) the primary user is military radiolocation, specifically naval radar. Amateur radio operators have secondary privileges to the Federal radiolocation service in the entire band and may not cause interference to these users. Amateur operators are allocated this band are in a co-secondary basis with ISM devices and space research. Amateur, space research, and ISM operators each have the "right to operate". Due to the lack of a high number of Part 15 users (compared to 2.4 GHz), the noise level tends to be lower in many parts of the US but can be quite congested in urban centers and on mountaintops. The frequencies from 5.6-5.65 GHz (channel 132) should generally be avoided to prevent interfering with TDWR weather radar stations.

802.11b/g/n

The 13 cm band is shared with Part 15 users as well as the Federal radiolocation service, and ISM (industrial, scientific, medical) devices. Amateur radio operators have secondary privileges to the Federal radiolocation service in the entire band and may not cause interference to these users. Amateur radio operators have primary privileges to ISM devices from 2.390–2.417 GHz and secondary privileges from 2.417–2.450 GHz. Because of the high number of Part 15 users, the noise level in this band tends to be rather high.

802.11y

The 9 cm band is shared with fixed services and space-to-Earth communications. Amateur radio operators using this band may not cause interference to other licensed users, including government radar stations. The low number of users tends to make this band quiet.

Identification

As with any amateur radio mode, stations must identify at least once every 10 minutes. One acceptable method for doing so is to transmit one's call sign inside an ICMP echo request (commonly known as a ping). If the access point is set to "master" then the user's call sign may be set as the "SSID" and therefore will be transmitted at regular intervals.

It is also possible to use a DDNS "push" request to automatically send an amateur call sign in plain text (ASCII) every 10 minutes. This requires that a computer's hostname be set to the call sign of the amateur operator and that the DHCP servers lease time be set to less than or equal to 10 minutes. With this method implemented the computer will send a DNS "push" request that includes the local computers hostname every time the DHCP lease is renewed. This method is supported by all modern operating systems including but not limited to Windows, Mac OS X, BSD, and Linux.

802.11 hardware may transmit and receive the entire time it is powered on even if the user is not sending data.

Security

Because the meaning of amateur transmissions may not be obscured, security measures that are implemented must be published. This does not necessarily restrict authentication or login schemes, but it does restrict fully encrypted communications. This leaves the communications vulnerable to various attacks once the authentication has been completed. This makes it very difficult to keep unauthorized users from accessing HSMM networks, although casual eavesdroppers can effectively be deterred. Current schemes include using MAC address filtering, WEP and WPA/WPA2. MAC address filtering and WEP are all hackable by using freely available software from the Internet, making them the less secure options. Per FCC rules the encryption keys themselves must be published in a publicly accessible place if using WEP, WPA/WPA2 or any other encryption[ citation needed ], thereby undermining the security of their implementation. Such measures however are effective against casual or accidental wireless intrusions.

Using professional or modified hardware it is possible to operate on 802.11a channels that are outside the FCC authorized Part 15 bands but still inside the 5.8 GHz (5 cm) or 2.4 GHz (13 cm) amateur radio bands. Transverters or "frequency converters" can also be used to move HSMM 802.11b/g/n operations from the 2.4 GHz (13 cm) band to the 3.4 GHz (9 cm) amateur radio band. Such relocation provides a measure of security by operating outside the channels available to unlicensed (Part 15) 802.11 devices.

Custom frequencies

Using amateur-only frequencies provide better security and interference characteristics to amateur radio operators. In the past it used to be easy to use modified consumer grade hardware to operate 802.11 on channels that are outside of the normal FCC allocated frequencies for unlicensed users but still inside an amateur radio band. However, regulatory concerns with the non-authorized use of licensed band frequencies is making it harder. The newer Linux drivers implement Custom Regulatory Database that prevents a casual user from operating outside of the country-specific operating bands. This requires the use of radio transceivers based on the use of Transverter (or frequency converter) technology.

420 MHz

Doodle Labs is a privately held manufacturing company with headquarters in Singapore that designs and manufactures a line of long range Wireless Data Transceiver devices.

The DL-435 is mini-PCI adapter based on the Atheros wireless chipset.

XAGYL Communications is a Canadian Distributor of Ultra High-Speed, Long Range Wireless equipment.

The XAGYL Communications XC420M is a mini-PCI adapter based on the Atheros wireless chipset.

The Atheros chipset's ability to use 5 MHz transmission bandwidths could allow part 97 operation on the 420–430 MHz ATV sub-band. (Note that 420–430 MHz operation is not allowed near the Canada–US border. Refer to the "Line A" rule.)

900 MHz

Transverters as well as using older 802.11 hardware such as the original NRC WaveLan or FHSS modems made by Aerocomm and FreeWave make it possible to operate on this band. Ubiquiti M9-series also provide hardware capable in this band. Beware that noise floor on this band in the larger cities is usually very high, which severely limits receiver performance.

2.4 GHz custom frequencies

Using professional grade hardware or modified consumer grade hardware it is possible to operate on 802.11b/g hardware on channels that are effectively: "−1" at 2.402 GHz, and "−2" at 2.397 GHz. Using these channels allows amateur operators to move away from unlicensed Part 15 operators but may interfere with amateur radio satellite downlinks near 2.400 GHz and 2.401 GHz.

3.3–3.8 GHz

Frequency conversion involves the use of transverters that convert the operating frequency of the 802.11b/g device from 2.4 GHz to another band entirely. Transverter is a technical term and is rarely used to describe these products which are more commonly known as frequency converters, up/down converters, and just converters. Commercially available converters can convert a 2.4 GHz 802.11b/g signal to the 3.4 GHz (9 cm) band which is not authorized for unlicensed Part 15 users.

Ubiquiti Networks has four radios based on Atheros chipsets with transverters on board for this band. The PowerBridge M3 and M365 for 3.5 GHz and 3.65 GHz respectively for aesthetically low profile PtP (Point-to-Point) connections. The Nanostation M3 and M365 are in a molded weatherproof case with 13.7 dBi dual polarization antennas. The Rocket M3, M365 and M365 GPS are in a rugged case using a hi-power, very linear 2x2 MIMO radio with 2x RP-SMA (Waterproof) connectors. Finally the NanoBridge M3 and M365 for long range PtP connections. These devices use N mode Atheros chipsets along with Ubiquiti's airMax TDMA protocol to overcome the hidden node problem which is commonly an issue when using ptmp wireless outdoors. UBNT currently does not allow sales to U.S. Amateurs and only sell these radios under FCC License. This may be due to exclusion areas near coasts and US Navy installations. The 3.5 GHz band is currently used for DoD or Navy (shipborne and ground-based) radar operations and covers 60 percent of the U.S. population. This however may change due to a recent FCC NPRM & Order.

5.8 GHz custom frequencies

Using professional grade hardware or modified consumer grade hardware it is possible to operate on 802.11a channels 116–140 (5.57–5.71 GHz) and channels above 165 (> 5.835 GHz). These frequencies are outside of the FCC-allocated Part 15 unlicensed band, but still inside of the 5.8 GHz (5 cm) amateur radio band. Modifying consumer hardware to operate on these expanded channels often involves installing after-market firmware and/or changing the "country code" setting of the wireless card. When buying professional grade hardware, many companies will authorize the use of these expanded frequencies for a small additional fee.

Custom firmware

One popular way to access amateur-only frequencies is to modify an off-the-shelf access point with custom firmware. This custom firmware is freely available on the Internet from projects such as DD-WRT and OpenWrt. The AREDN Project supports off-the-shelf firmware that supports Part-97-only frequencies on Ubiquiti and TP-Link hardware. [8] A popular piece of hardware that is modified is the Linksys WRT54GL because of the widespread availability of both the hardware and third-party firmware, however, the Linksys hardware is not frequency agile due to the closed nature of the Linksys drivers.

See also

Related Research Articles

<span class="mw-page-title-main">IEEE 802.11</span> Wireless network standard

IEEE 802.11 is part of the IEEE 802 set of local area network (LAN) technical standards, and specifies the set of medium access control (MAC) and physical layer (PHY) protocols for implementing wireless local area network (WLAN) computer communication. The standard and amendments provide the basis for wireless network products using the Wi-Fi brand and are the world's most widely used wireless computer networking standards. IEEE 802.11 is used in most home and office networks to allow laptops, printers, smartphones, and other devices to communicate with each other and access the Internet without connecting wires. IEEE 802.11 is also a basis for vehicle-based communication networks with IEEE 802.11p.

The ISM radio bands are portions of the radio spectrum reserved internationally for industrial, scientific, and medical (ISM) purposes, excluding applications in telecommunications. Examples of applications for the use of radio frequency (RF) energy in these bands include RF heating, microwave ovens, and medical diathermy machines. The powerful emissions of these devices can create electromagnetic interference and disrupt radio communication using the same frequency, so these devices are limited to certain bands of frequencies. In general, communications equipment operating in ISM bands must tolerate any interference generated by ISM applications, and users have no regulatory protection from ISM device operation in these bands.

<span class="mw-page-title-main">Ultra high frequency</span> Electromagnetic spectrum 300–3000 MHz

Ultra high frequency (UHF) is the ITU designation for radio frequencies in the range between 300 megahertz (MHz) and 3 gigahertz (GHz), also known as the decimetre band as the wavelengths range from one meter to one tenth of a meter. Radio waves with frequencies above the UHF band fall into the super-high frequency (SHF) or microwave frequency range. Lower frequency signals fall into the VHF or lower bands. UHF radio waves propagate mainly by line of sight; they are blocked by hills and large buildings although the transmission through building walls is strong enough for indoor reception. They are used for television broadcasting, cell phones, satellite communication including GPS, personal radio services including Wi-Fi and Bluetooth, walkie-talkies, cordless phones, satellite phones, and numerous other applications.

Wireless local loop (WLL) is the use of a wireless communications link as the "last mile / first mile" connection for delivering plain old telephone service (POTS) or Internet access to telecommunications customers. Various types of WLL systems and technologies exist.

The S band is a designation by the Institute of Electrical and Electronics Engineers (IEEE) for a part of the microwave band of the electromagnetic spectrum covering frequencies from 2 to 4 gigahertz (GHz). Thus it crosses the conventional boundary between the UHF and SHF bands at 3.0 GHz. The S band is used by airport surveillance radar for air traffic control, weather radar, surface ship radar, and some communications satellites, particularly satellites used by NASA to communicate with the Space Shuttle and the International Space Station. The 10 cm radar short-band ranges roughly from 1.55 to 5.2 GHz. The S band also contains the 2.4–2.483 GHz ISM band, widely used for low power unlicensed microwave devices such as cordless phones, wireless headphones (Bluetooth), wireless networking (WiFi), garage door openers, keyless vehicle locks, baby monitors as well as for medical diathermy machines and microwave ovens. India's regional satellite navigation network (IRNSS) broadcasts on 2.483778 to 2.500278 GHz.

Code of Federal Regulations, Title 47, Part 15 is an oft-quoted part of Federal Communications Commission (FCC) rules and regulations regarding unlicensed transmissions. It is a part of Title 47 of the Code of Federal Regulations (CFR), and regulates everything from spurious emissions to unlicensed low-power broadcasting. Nearly every electronics device sold inside the United States radiates unintentional emissions, and must be reviewed to comply with Part 15 before it can be advertised or sold in the US market.

<span class="mw-page-title-main">Cordless telephone</span> Portable telephone that connects to a landline

A cordless telephone or portable telephone has a portable telephone handset that connects by radio to a base station connected to the public telephone network. The operational range is limited, usually to the same building or within some short distance from the base station.

The 33-centimeter or 900 MHz band is a portion of the UHF radio spectrum internationally allocated to amateur radio on a secondary basis. It ranges from 902 to 928 MHz and is unique to ITU Region 2 (Americas). It is primarily used for very local communications as opposed to bands lower in frequency. However, very high antennas with high gain have shown 33 centimeters can provide good long-range communications almost equal to systems on lower frequencies such as the 70 centimeter band. The band is also used by industrial, scientific, and medical (ISM) equipment, as well as low-powered unlicensed devices. Amateur stations must accept harmful interference caused by ISM users but may receive protection from unlicensed devices.

802.11j-2004 or 802.11j is an amendment to the IEEE 802.11 standard designed specially for Japanese market. It allows wireless LAN operation in the 4.9–5.0 GHz band to conform to the Japanese rules for radio operation for indoor, outdoor and mobile applications. The amendment has been incorporated into the published IEEE 802.11-2007 standard.

The Unlicensed National Information Infrastructure (U-NII) radio band, as defined by the United States Federal Communications Commission, is part of the radio frequency spectrum used by WLAN devices and by many wireless ISPs.

IEEE 802.11n-2009, or 802.11n, is a wireless-networking standard that uses multiple antennas to increase data rates. The Wi-Fi Alliance has also retroactively labelled the technology for the standard as Wi-Fi 4. It standardized support for multiple-input multiple-output, frame aggregation, and security improvements, among other features, and can be used in the 2.4 GHz or 5 GHz frequency bands.

IEEE 802.11y-2008 is an amendment to the IEEE 802.11-2007 standard that enables data transfer equipment to operate using the 802.11a protocol on a co-primary basis in the 3650 to 3700 MHz band except when near a grandfathered satellite earth station. IEEE 802.11y is only being allowed as a licensed band. It was approved for publication by the IEEE on September 26, 2008.

Long-range Wi-Fi is used for low-cost, unregulated point-to-point computer network connections, as an alternative to other fixed wireless, cellular networks or satellite Internet access.

IEEE 802.11a-1999 or 802.11a was an amendment to the IEEE 802.11 wireless local network specifications that defined requirements for an orthogonal frequency-division multiplexing (OFDM) communication system. It was originally designed to support wireless communication in the unlicensed national information infrastructure (U-NII) bands as regulated in the United States by the Code of Federal Regulations, Title 47, Section 15.407.

IEEE 802.11g-2003 or 802.11g is an amendment to the IEEE 802.11 specification that operates in the 2.4 GHz microwave band. The standard has extended link rate to up to 54 Mbit/s using the same 20 MHz bandwidth as 802.11b uses to achieve 11 Mbit/s. This specification, under the marketing name of Wi‑Fi, has been implemented all over the world. The 802.11g protocol is now Clause 19 of the published IEEE 802.11-2007 standard, and Clause 19 of the published IEEE 802.11-2012 standard.

The 13 centimeter, 2.3 GHz or 2.4 GHz band is a portion of the UHF (microwave) radio spectrum internationally allocated to amateur radio and amateur satellite use on a secondary basis. The amateur radio band is between 2300 MHz and 2450 MHz, and thereby inside the S-band. The amateur satellite band is between 2400 MHz and 2450 MHz, and its use by satellite operations is on a non-interference basis to other radio users. The license privileges of amateur radio operators include the use of frequencies and a wide variety of modes within these ranges for telecommunication. The allocations are the same in all three ITU Regions.

There are several uses of the 2.4 GHz ISM radio band. Interference may occur between devices operating at 2.4 GHz. This article details the different users of the 2.4 GHz band, how they cause interference to other users and how they are prone to interference from other users.

Wireless Medical Telemetry Service (WMTS) is a wireless service specifically defined in the United States by the Federal Communications Commission (FCC) for transmission of data related to a patient's health (biotelemetry). It was created in 2000 because of interference issues due to establishment of digital television. The bands defined are 608-614 MHz, 1395-1400 MHz and 1427-1432 MHz. Devices using these bands are typically proprietary. Further, the use of these bands has not been internationally agreed to, so many times devices cannot be marketed or used freely in countries other than the United States.

<span class="mw-page-title-main">C band (IEEE)</span> Range of radio frequencies from 4 to 8 GHz

The C band is a designation by the Institute of Electrical and Electronics Engineers (IEEE) for a portion of the electromagnetic spectrum in the microwave range of frequencies ranging from 4.0 to 8.0 gigahertz (GHz). However, the U.S. Federal Communications Commission C band proceeding and auction, designated 3.7–4.2 GHz as C band. The C band is used for many satellite communications transmissions, some Wi-Fi devices, some cordless telephones, as well as some radar and weather radar systems.

References

  1. "Amateur Radio Emergency Data Network". www.arednmesh.org.
  2. "Broadband-Hamnet". www.broadband-hamnet.org.
  3. "ARRL :: Warning". www.arrl.org.
  4. "Using IEEE 802.11b Operating Under Part 97 of the FCC Rules". www.arrl.org.
  5. HSMM Radio Equipment arrl.org
  6. 1 2 3 "IEEE 802.11ah | Sub GHz Wi-Fi | Electronics Notes". www.electronics-notes.com.
  7. "Operation in U-NII Bands – 802.11 Channel Plan (§15.407)". FCC. Retrieved 30 July 2023.
  8. "Amateur Radio Emergency Data Network". AREDNmesh.org.