The AR platform has become widely popular for makers of hunting and sporting rifles. Although the designations "AR-10" and "AR-15" are respectively trademarks of ArmaLite and Colt, variants of both are made by many manufacturers. The AR-15 rifle usually comes chambered for either the military cartridge 5.56×45mm or the .223 Remington. Because of the pressures associated with the 5.56×45mm, it is not advisable to fire 5.56×45mm rounds in an AR-15 marked as .223 Remington, since this can result in damage to the rifle or injury to the shooter.[citation needed] The AR-15 can be chambered in many other calibers; it is then often referred to as an AR-15 style rifle.
.222 Remington (sometimes chambered in countries where ownership of military cartridges is illegal)
.223 Remington – Original AR-15 cartridge: .223 cartridges may function in a 5.56×45mm rifle, however 5.56×45mm cartridges may produce excessive pressure in a .223 Rem rifle. On the other hand, a.223 Wylde chamberis used on .223 Rem rifle barrels to allow them to safely fire either.223 Remingtonor5.56×45mm NATOammunition.[5]
Some companies have created AR pattern rifles that depart from the standard AR-15 and AR-10 dimensions in order to accommodate other types of ammunition that would not fit into those standards.
Examples include (sorted by overall cartridge length):
Some of the calibers listed above use a proprietary case that is specific to that given cartridge. Other cartridges were derived from re-forming an existing case and possibly trimming the length in order to arrive at a case-shape that meets the standardized SAAMI-spec dimensions.
AR-15:
22 Nosler, Proprietary, uses the head and rim dimensions of the 5.56x45, and a case-body that is similar to the 6.8 SPC case. To increase powder capacity, the shoulder is located higher than the 6.8, and the case is longer. The neck is sized for .224 caliber bullets.
224 Valkyrie, Uses 6.8 SPC cases, trimmed shorter, and the shoulder re-formed at a lower location due to being designed for using relatively long "high BC" (Ballistic Coefficient) bullets. The neck is sized for .224 caliber bullets.
25-45 Sharps, Uses the standard military 5.56x45 case (also .223 cases), the neck is simply expanded to .257"
6.5mm Grendel, The Grendel uses the same head and rim from the .220 Russian and the 7.62x39 with a rim diameter of 0.441-0.449. The 6.5 Grendel bullets have a true diameter of 6.71mm / 0.264" and the 6.5 Grendel case can be formed from abundant 7.62x39 cases with a neck re-sizing die, and fire-forming a slight change to the shoulder, if the case is made from brass. Many of the popular 7.62x39 cases are made from steel, which will not work for reforming the shoulder.
277 Wolverine, Standard military 5.56x45 case (also .223), shoulder is reformed lower, length is trimmed, neck is sized to .277
6.8 SPC (.277), Proprietary. Developed as an all new cartridge in the hopes of gaining a military contract. Rim diameter is 0.421"
300 AAC Blackout, Uses military 5.56x45 (also .223). The shoulder is reformed, length is trimmed, neck is sized to .308. This caliber is very popular, and examples are available in a wide variety of styles. Bullet weights can currently be found between 100gr to 220gr
7.62x40 Wilson Tactical (300 HAM'R), Uses 5.56 NATO cases (also .223). Shoulder is re-formed, length is trimmed, neck is sized to .308. This cartridge is very similar to the 300 AAC Blackout, but the shoulder is slightly higher and the case is slightly taller, which allows for more gunpowder capacity when loading the lighter/shorter high-velocity bullets.
338 Spectre, Uses 10mm Magnum pistol cases with a 6.8 SPC bolt-face. A shoulder is formed, and the case is lightly trimmed to length, and the neck is sized to .338, down from 0.401". The 10mm rim is 0.424" (10.8mm) in diameter, and the SPC rim diameter is 0.422" (10.7mm). The .338 caliber bullets are available in weights between 200gr-250gr.
350 Legend, Proprietary. The head and rim dimensions exactly match the military 5.56x45 case, allowing the use of the standard bolt-face of an AR-15. However, the case has an added taper and is longer than 5.56x45 cases, so these cannot be reformed from any other existing case. The nominal bullet diameter is .357-inch, but SAAMI specs allow the bullet diameter variance to be .355-.357
357 Auto, Wildcat. Uses 10mm magnum pistol cases with a 6.8 SPC bolt-face. The existing 357-Sig pistol is a 9mm bullet shouldered into the larger 40 S&W pistol case. The 10mm cartridge and the 40 S&W are almost identical, but the 10mm case is longer and operates at a higher pressure. This means that you can use existing 357-Sig dies to re-form the straight-wall 10mm case into a shouldered .355" (9mm), and then the neck can be sized up to accept .358 rifle bullets. This is in response to the popularity of the 300 Blackout at subsonic velocities. If the bullet velocity is capped at 1,000-Feet Per Second / FPS in order to subdue the noise of firing, then the impact can be improved by increasing the weight of the bullet. The 357 Auto can be loaded with bullets in .358-caliber, while still fitting within the AR-15 COAL of 2.260". Bullet weights are currently available between 225gr-310gr
358 Yeti, Uses standard military 7.62x51 cases (also .308), length is trimmed, shoulder is reformed, neck is sized to .358". Bullet weights are currently available between 225gr-310gr
375 Stalker, Standard military 7.62x51 cases (also .308), length is trimmed, shoulder is reformed, neck is expanded to .375
375 SOCOM, Proprietary. The case head and rim dimensions exactly match the military 7.62x51 (also .308), however, the case body is slightly wider and has more taper.
400 AR, Wildcat. The parent is the 7.35×51mm Carcano rifle case. It has a rim diameter of 0.447", which allows the use of the 7.62x39mm bolt face of an AR-15. The case is necked out and trimmed off above the shoulder at a case-length of 1.700", with a COAL of 2.250", resulting in a "straight-wall" cartridge. It uses .4005" jacketed rifle bullets, and can accept bullets from .40 S&W and 10mm Auto pistols (135gr–230gr).
400 Legend, Proprietary. The rebated rim dimensions exactly match the 6.8mm Remington SPC case, allowing the use of the 6.8mm SPC bolt-face of an AR-15, but the case has a base diameter of .4400" and cannot be reformed from any other existing case. The 400 LGND uses .4005" jacketed rifle bullets.
450 Bushmaster, Uses .284 Winchester cases. Cut the length to 1.700" to form a straight-wall cartridge, from 2.170". The .284 Winchester case is very similar to the .308, however, the .284 case has a body diameter of 0.500", and the .308 case has a body diameter of 0.471". Both share an identical head/rim. The 450B is limited to 35,000-psi, which is more common in pistols, and lower than similarly sized rifle cartridges. The 450B uses .452" diameter bullets, most often seen in the abundant 45-caliber pistol styles. The 300gr version is rated at 1900fps at the muzzle, and the 250gr at 2200fps.
458 SOCOM, Proprietary. The case head and rim dimensions exactly match the military 7.62x51 (also .308), but the case body is slightly wider and has more taper.
50 Beowulf. Proprietary. The case head and rim dimensions exactly match the .44-Magnum pistol case, and all dimensions from the lower part of the case matches the 50-Action Express (50 AE), which can be described as a .44-Magnum cartridge that has had the body of the case expanded to 50-caliber while leaving the head intact. However, the 50 Beowulf case is longer than the 50AE, so the 50AE cases cannot be used as a donor.
Note about donor cases: The 7.62x51 military cartridge the civilian version is the .308 cartridge. Since its dimensions are taken from the 30-06 cartridge from the 1906 US Army cartridge, the lower half of these case dimensions have been used for designing the .243 Winchester, 25-06, .270 Winchester, .280 Remington, 7mm-08, .308, .30-06, .35 Whelen, and others. Any AR-15/AR-10 cartridge cases that are derived from the 7.62x51 can also be formed from these listed calibers. (7.62x51 & .308 are similar in external dimensions though the Brass has different internal capacity and Max PSI recommendations are different & Chambers are different.)
AR-10:
The AR-10 is slightly larger and heavier than the AR-15. It was originally designed to chamber the military 7.62x51 NATO cartridge (also .308), which has a COAL of 2.800" (71.12mm)
45 Raptor, uses the standard 7.62 NATO case, cut to a length of 1.800" from 2.015", resulting in a straight-wall cartridge, neck is sized to 0.452". The resulting COAL of 2.300" is only 1.02mm longer than the maximum COAL for chambering a cartridge in the smaller AR-15, however, the 45 Raptor chamber pressure is allowed to be as high as 62,000-PSI. This means that the stronger AR-10 receiver and bolt carrier group is needed for shooting this cartridge.
See also
STANAG magazine, a standardized firearm magazine based on the 5.56×45mm cartridge and similar length cartridges
A wildcat cartridge, often shortened to wildcat, is a custom cartridge for which ammunition and/or firearms are not mass-produced. These cartridges are often created in order to optimize a certain performance characteristic of an existing commercial cartridge, or may merely be intended as novelty items.
The .243 Winchester (6×52mm) is a popular sporting rifle cartridge. Developed as a versatile short action cartridge to hunt both medium game and small game alike, it "took whitetail hunting by storm" when introduced in 1955, and remains one of the most popular whitetail deer cartridges. It is also commonly used for harvesting blacktail deer, pronghorns and mule deer with heavier rounds, and is equally suited to varmint hunting with lighter rounds. The .243 is based on a necked down .308 Winchester, introduced only three years earlier. Expanding monolithic copper bullets of approximately 80 to 85 grains or traditional lead rounds of 90 to 105 grains with controlled expansion designs are best suited for hunting medium game, while lighter rounds are intended for varmints.
The .338 Whisper (8.59x38mm) is a wildcat cartridge in the Whisper family, a group of cartridges developed in the early 1990s by J.D. Jones of SSK Industries. Unlike the smaller caliber cartridges in the Whisper family, loads for the .338 Whisper are mainly limited to subsonic velocities.
The Whisper family of firearm cartridges is a group of wildcat cartridges developed in the early 1990s by J.D. Jones at SSK Industries. The Whisper family was developed as a line of accurate, multi-purpose cartridges using relatively heavy rifle bullets for a given caliber in subsonic loads. The intention was to create an extremely accurate cartridge family for military, police, competition and specialized hunting markets that could also be easily sound suppressed.
The .280 Remington, also known as the 7mm-06 Remington and 7mm Express Remington, was introduced in 1957 for the Remington model 740, 760, 721, and 725 rifles.
The 7mm Remington Magnum rifle cartridge was introduced as a commercially available round in 1962, along with the new Remington Model 700 bolt-action rifle. It is a member of the belted magnum family that is directly derived from the venerable .375 H&H Magnum. The original purpose of the belted magnum concept taken from the .300 H&H Magnum and .375 H&H Magnum, was to provide precise headspace control, since the sloping shoulders, while easing cartridge extraction, were unsuitable for this purpose. Improved cartridge extraction reliability is desirable while hunting dangerous game, in particular when a fast follow-up shot is required. The 7mm Remington Magnum is based on the commercial .264 Winchester Magnum, .338 Winchester Magnum, and .458 Winchester Magnum, which were based on the same belted .300 H&H Magnum and .375 H&H Magnum cases, trimmed to nearly the same length as the .270 Weatherby Magnum.
The 8mm Remington Magnum belted rifle cartridge was introduced by Remington Arms Company in 1978 as a new chambering for the model 700 BDL rifle. The 8mm Remington Magnum's parent case is the .375 H&H Magnum. It is a very long and powerful cartridge that cannot be used in standard length actions, such as those that accommodate the .30-06 Springfield.
The .300 Remington Ultra Magnum, also known as the .300 Ultra Mag, 7.62×72mm or .300 RUM, is a 7.62 mm rifle cartridge introduced by Remington Arms in 1999. The .300 Remington Ultra Magnum is one of the largest commercially available .30 caliber magnums currently being produced. It is a beltless, rebated rim cartridge, capable of handling all large North American game, as well as long-range shooting. Among commercially produced .30-caliber rifle chamberings, the .300 Remington Ultra Magnum is second only to the .30-378 Weatherby Magnum in cartridge-case capacity.
The .260 Remington cartridge was introduced by Remington in 1997. Many wildcat cartridges based on the .308 Winchester case had existed for years before Remington standardized this round.
.22 caliber, or 5.6 mm, refers to a common firearms bore diameter of 0.22 inch (5.6 mm) in both rimfire and centerfire cartridges.
The .284 Winchester (7.21x55mmRB) is a rebated rim firearm cartridge, introduced by Winchester in 1963.
Parker Otto Ackley was an American gunsmith, barrel maker, author, columnist, and wildcat cartridge developer. The Ackley Improved family of wildcat cartridges are designed to be easily made by rechambering existing firearms, and fireforming the ammunition to decrease body taper and increase shoulder angle, resulting in a higher case capacity. Ackley improved not only standard cartridges, but also other popular wildcats, and was the first to create a .17 caliber (4.5 mm) centerfire cartridge.
The 6.5mm Creedmoor (6.5×48mm), designated 6.5 Creedmoor by SAAMI, 6.5 Creedmoor by the C.I.P. or 6.5 CM or 6.5 CRDMR for short, is a centerfire rifle cartridge introduced by Hornady in 2007. It was developed by Hornady senior ballistics scientist Dave Emary in partnership with Dennis DeMille, the vice-president of product development at Creedmoor Sports, hence the name. The cartridge is a necked-down modification of the .30 Thompson Center.
The 6×45mm is a rimless, bottlenecked cartridge based on the .223 Remington or 5.56 NATO cartridge necked up to .243 (6mm). The cartridge is also known as the 6mm-223 Remington or 6mm/223.
The 6mm AR is a centerfire wildcat cartridge initially designed by Robert Whitley for long-range performance in an AR-15 rifle.
.30-06 Springfield wildcat cartridges are cartridges developed from a 30-06 Springfield "parent cartridge" through narrowing or widening the cartridge neck to fit a smaller or larger bullet in an attempt to improve performance in specific areas. Such wildcat cartridges are not standardized with recognized small arms standardization bodies like the SAAMI and the CIP.
A varmint rifle is a small-caliber precision firearm or high-powered airgun primarily used for both varmint hunting and pest control. These tasks include killing three types of pests or nuisance animals that spread diseases or destroy crops or livestock:
The .277 Wolverine (6.8x39mm) is a wildcat cartridge. It is a multi-purpose mid-power cartridge with increased ballistic performance over the AR-15's traditional .223 Remington cartridge. The use of a modified 5.56 case means that at minimum, only a new barrel is needed to convert any 5.56-based firearm to .277 Wolverine.
Nosler produces six different rebated rim hunting cartridges. The first to be introduced was .26 Nosler, followed by .28 Nosler, .30 Nosler, .33 Nosler, .22 Nosler, and .27 Nosler.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
