Mack TerraPro

Last updated
Mack TerraPro
Joralemon Tubes Service Restoration (20558525020) (cropped).jpg
Production history
TypeHeavy-duty/severe service
Cab-over-engine
ManufacturerMack Trucks
Years builtfrom 2007
PredecessorMC/MR series
Maximum weights
Weight class8
Truck81,000 lb (37,000 kg)
Front axle23,000 pounds (10,000 kg)
Rear axles65,000 lb (29,000 kg)
Drivetrain
Diesel enginesMack MP7, MP8
CNG engineCummins Westport L9N
TransmissionsMack 6-18-spd
Eaton-Fuller 9-18-spd
Allison 5 and 6-spd
Chassis
Front axleSingle, twin-steer avail
Rear axlesSingle and tandem
lift axles available
Drive layout4x2, 6x4, 8x4
plus lift axles

The Mack TerraPro is a series of heavy duty (Class 8) and severe service trucks built by Mack Trucks. They are a forward control cab-over-engine type, where the driver sits in front of the axle. A flat front has two large windshields. A spotting feature is small notches in the lower inside of the windshields. It is used in refuse service and for construction concrete pumps.

Contents

A variant, the TerraPro Low Entry, with the cab mounted very low and forward, was renamed Mack LR in 2018.

Design

The TerraPro is a forward control cab-over-engine with a low cab in front of the axle. This allows very tight turning radius for the overall length of the truck. The low cab also lets a boom operate over it. There is an available right-side driving position. Commonly a 6x4 (3 axles, 2 powered) tandem steer front and extra lift axles are available. Total loaded weight can be up to 81,000 pounds (37,000 kg) on three or more axles.

Advanced electronics are used for engine, chassis, and body controls, as well as maintenance. All trucks have ABS. Rear-view cameras are often fitted.

Mack builds their own major components (engines, transmissions, axles, and suspensions) and promotes an integrated design. Most vendor components are also available but engine choice is very limited.

Engines

The TerraPro is available with two Mack diesels and a Cummins Westport natural gas engine. [1]

The Mack MP7 is the base engine in the TerraPro. It is a 659 cubic inches (10.8 L) overhead cam turbocharged inline six-cylinder diesel engine. It develops 325 to 425 horsepower (242 to 317 kW) and 1,260 to 1,560 pound force-feet (1,710 to 2,120 N⋅m) of torque. [2]

The Mack MP8 engine is the largest engine in the TerraPro. It is a 783 cubic inches (12.8 L) overhead cam turbocharged inline six-cylinder engine. It develops 415 to 505 horsepower (309 to 377 kW) and 1,460 to 1,867 pound force-feet (1,979 to 2,531 N⋅m) of torque. It has been in production since 2007. [3]

The Cummins Westport L9N is a 543 cubic inches (8.9 L) turbocharged inline six-cylinder natural gas engine. It develops 329 horsepower (245 kW) and 1,000 pound force-feet (1,400 N⋅m) of torque. [4]

Transmissions

Both Mack and Eaton-Fuller have manual and automated shifting models. Manual transmissions have five or six main gears, extra ratios are made with different combinations of ranges. Allison transmissions are fully automatic.

Mack mDRIVE automated manual is the base transmission. It has no clutch pedal and shifts itself on demand. The driver can override it but it is normally driven in "D". It can have 12, 13, or 14-speeds. [5] Other Mack manual transmissions have 8-18 speeds.

Eaton-Fuller UltraShift automated shifting systems are available on all of their transmissions from 9- to 18-speeds.

Allison RDS series 5- or 6-speed transmissions are used on most refuse trucks. The RDS is a fully automatic planetary gear transmission with a lock-up torque converter.

Transfer cases are used on concrete pumps. They direct full transmission output to either the drive-line or the pump, but not both.

Frame

A ladder frame with beam axles is used. Front axles are on semi-elliptical leaf springs and tandem steer axles are available. The base rear suspension is a Mack tandem but other axle/suspension available. Wheelbases are from 159 to 220 inches (400 to 560 cm). The TerraPro has more frame options than other Mack trucks.

Dana-Spicer and Meritor supply air brakes, steering systems, driveshafts, and other components.

Axles and suspensions

Front axles are available from 12,000 to 23,000 pounds (5,400 to 10,400 kg). Multi-leaf leaf springs are base, tapered leaves are optional. Springs have an eye mount at front but at the rear the spring goes through a solidly-mounted slipper. The slipper is stronger side to side than the typical shackle arrangement.

Mack powered axles have the drive carrier on top of the housing instead of the front of it like other manufacturers. This lets the driveshafts be in line from the transmission to and between the axles at a higher level above the ground. With the higher level above the ground the driveshafts and u-joints are less prone to dirt and damage, important in on/off road construction.

Other powered axles are available from Dana-Spicer and Meritor. These have front mounted carriers and in tandems the two axle housings are different.

Single rear axles rated at 23,000 pounds (10,000 kg) are available from Mack and Meritor.

The Camelback tandem is the base rear suspension. The Camelback has multiple leaves that rock above the bogey pivot then curve down and under the axles. It is strong in on/off-road service. It is available in ratings of 38,000, 44,000, 52,000, and 65,000 pounds (17,000, 20,000, 24,000, and 29,000 kg).

The mRIDE tandem has tapered leaves that rock above the bogey pivot then go out and above the axles. Struts go from the bottom of the bogey pivot out and under the axle. They have more wheel travel and ground clearance than the camelback. They are rated at 40,000, 48,000, and 52,000 pounds (18,000, 22,000, and 24,000 kg).

Walking beams have low bogie pivots with a balance beam going out and under the axles. Any suspension is above the bogey pivot. Walking beams are very stable at low speeds and when stopped. Mack and Hendrickson models are available.

Vendor tandems from Chalmers, Hendrickson, Meritor, and RAYCO are rated at up to 46,000 pounds (21,000 kg).

Applications

Refuse

Front loaders drive directly up to a container. A boom goes from the body over and then down in front of, the cab. As the truck moves forward slowly two forks pick up the container. The container is then lifted up and over the cab to be dumped into a hopper on the top of the body. Front loaders are used for commercial pickup.

Side loaders drive next to bins placed on the curb. Most have a way to self-load from bins. Some have a low hopper between the cab and body. Others have an arm that picks up the bin, raises it up along the side of the body, then dumps it in a hopper on the top of the body. Side loaders are used for residential curb-side pickup. They have additional right (curb) side driving controls.

Rear loaders have a large hopper on the rear end. Typically a rear crew can load loose material, bins with assist, oversize pieces, and small containers. They are used for residential and light commercial pickup in congested cities.

Roll-off container trucks have a container that is raised in the front and slides off the back of the truck onto the ground. When a loaded box is carried it can be unloaded like a dump truck. They commonly haul construction debris but refuse containers are also left at commercial sites. TerraPros are sometimes used in congested cities when extreme maneuverability is required.

Construction

Concrete pumps have a multi-stage folding boom pivoted near the center of the truck and a hopper at the rear to load the pump. The pump itself is the load and the truck always operates at maximum weight. In transit the boom is folded front to rear. In use the pump uses outriggers and the boom unfolds forward over the cab or to either side. Large pumps can have multiple extra axles.

Concrete conveyors have a telescopic conveyor belt. They do similar work to a pump but are limited and rarely as heavy as a pump.

Other uses

Custom models for limited production are available but the cab-over-engine type has limited applications in the United States. The Massachusetts Bay Transportation Authority in Boston has two and three axle snowplow models.

Related Research Articles

<span class="mw-page-title-main">Mack Trucks</span> American truck manufacturing company

Mack Trucks, Inc. is an American truck manufacturing company and a former manufacturer of buses and trolley buses. Founded in 1900 as the Mack Brothers Company, it manufactured its first truck in 1905 and adopted its present name in 1922. Mack Trucks is a subsidiary of AB Volvo, which purchased Mack along with its then parent company Renault Véhicules Industriels in 2000.

<span class="mw-page-title-main">Ram pickup</span> American full-size pickup built by Stellantis

The Ram pickup is a full-size pickup truck manufactured by Stellantis North America and marketed from 2010 onwards under the Ram Trucks brand. The current fifth-generation Ram debuted at the 2018 North American International Auto Show in Detroit, Michigan, in January of that year.

<span class="mw-page-title-main">Dump truck</span> Truck which can tip its bed, dumping its contents

A dump truck, known also as a dumping truck, dump trailer, dumper trailer, dump lorry or dumper lorry or a dumper for short, is used for transporting materials for construction as well as coal. A typical dump truck is equipped with an open-box bed, which is hinged at the rear and equipped with hydraulic rams to lift the front, allowing the material in the bed to be deposited ("dumped") on the ground behind the truck at the site of delivery. In the UK, Australia, South Africa and India the term applies to off-road construction plants only and the road vehicle is known as a tip lorry, tipper lorry, tipper truck, tip truck, tip trailer or tipper trailer or simply a tipper.

<span class="mw-page-title-main">M939 series 5-ton 6×6 truck</span> 5-ton 6x6 trucks

The M939 is a 5-ton 6×6 U.S. military heavy truck. The basic cargo versions were designed to transport a 10,000 pounds (4,500 kg) cargo load over all terrain in all weather. Designed in the late 1970s to replace the M39 and M809 series of trucks, it has been in service ever since. The M939 evolved into its own family of cargo trucks, dump trucks, semi-tractors, vans, wreckers, and bare chassis/cabs for specialty bodies. 44,590 in all were produced.

<span class="mw-page-title-main">M19 Tank Transporter</span> 45-ton Truck-trailer

The M19 Tank Transporter was a heavy tank transporter system used in World War II and into the 1950s. It consisted of a 12-ton 6×4 M20 Diamond T Model 980 truck and companion 12-wheel M9 trailer.

<span class="mw-page-title-main">Diamond T</span> Defunct American motor vehicle manufacturer

The Diamond T Company was an American automobile and truck manufacturer. They produced commercial and military trucks.

<span class="mw-page-title-main">Logistics Vehicle System</span> American military vehicle family

The Logistics Vehicle System (LVS), nicknamed by U.S. Marines as "Dragon Wagon", is a modular assortment of eight-wheel drive all-terrain vehicle unit combinations used by the United States Marine Corps.

<span class="mw-page-title-main">Articulated hauler</span>

An articulated hauler, articulated dump truck (ADT), or sometimes a dump hauler, is a very large heavy-duty type of dump truck used to transport loads over rough terrain, and occasionally on public roads. The vehicle usually has all-wheel drive and consists of two basic units: the front section, generally called the tractor, and the rear section that contains the dump body, called the hauler or trailer section. Steering is made by pivoting the front in relation to the back by hydraulic rams. This way, all wheels follow the same path, making it an excellent off-road vehicle.

<span class="mw-page-title-main">International Transtar</span> Truck range

The International TranStar, is a range of Class 8 trucks produced by Navistar International for North America. Produced nearly exclusively as a semitractor, the product range is focused towards local delivery and regional shipping.

<span class="mw-page-title-main">M915 (truck)</span> Tractor unit used for line haul missions by the US Army

The M915 is a tractor unit used for line haul missions by the United States Army. Designed for use on improved roads, it does not have a driven front axle.

<span class="mw-page-title-main">Mack Pinnacle</span>

The Mack Pinnacle is a series of heavy duty trucks produced by Mack Trucks. Introduced in 2006, the Pinnacle is the successor of the Mack Vision. Currently, the product line is sold in the United States and Canada; in Venezuela and Peru, the Pinnacle is marketed as the Mack Vision Elite.

<span class="mw-page-title-main">M123 and M125 10-ton 6x6 trucks</span> 10-ton 6x6 trucks

The Mack M123 (G792) was a 10-ton 6x6 semi-tractor introduced in 1955. The Mack M125 was a heavy cargo truck version of the M123. The M123 was used to tow tank transporter trailers while the M125 towed field artillery pieces.

<span class="mw-page-title-main">Mack MC/MR series</span> Motor vehicle

The Mack MC/MR series, also known as the "Cruise-Hauler", is a cabover truck first introduced in 1978. It is of a distinct "set back front axle" design, with the driver compartment mounted ahead of the front axle and with a large, flat, divided windscreen covering almost half of the truck's frontal aspect.

<span class="mw-page-title-main">6-ton 6×6 truck</span> US military truck

The 6-ton 6×6 truck was a family of heavy tactical trucks built for the United States Army during World War II. The basic cargo version was designed to transport a 6- short ton (5,400 kg) cargo load over all terrain in all weather. The chassis were built by Brockway Motor Company, The Corbitt Company, The Four Wheel Drive Auto Company (FWD), Ward LaFrance Truck Corporation, and White Motor Company. They were replaced by the M54 5-ton 6x6 trucks in the 1950s.

<span class="mw-page-title-main">5-ton 6×6 truck</span>

The 5‑ton 6x6 truck, officially "Truck, 5-ton, 6x6", was a class of heavy-duty six-wheel drive trucks used by the US Armed Forces. The basic cargo version was designed to transport a 5-ton (4,500 kg) load over all roads and cross-country terrain in all weather. Through three evolutionary series there have been component improvements, but all trucks were mechanically very similar. They were the standard heavy-duty truck of the US military for 40 years, until replaced by the Medium Tactical Vehicle (MTV) beginning in 1991.

<span class="mw-page-title-main">Diamond T 4-ton 6×6 truck</span> US Army heavy tactical truck

The Diamond T 4-ton 6×6 truck was a heavy tactical truck built for the United States Army during World War II. Its G-number was G-509. Cargo models were designed to transport a 4-ton (3,600 kg) load over all terrain in all weather. There were also wrecker, dump, and other models. They were replaced by the M39 series 5-ton 6×6 trucks in the 1950s.

<span class="mw-page-title-main">Mack Granite</span>

The Mack Granite is a series of heavy duty and severe service trucks built by Mack Trucks. It has a long, low-profile hood and a high-visibility cab. Designed as straight trucks for local construction, waste removal, and other vocational jobs, it is also available as a semi-tractor. Introduced in 2001, it remains in production as of today.

<span class="mw-page-title-main">Mack LR</span> Truck chassis manufactured by Mack Trucks

The Mack LR(Low Ride) is a series of heavy-duty trucks built by Mack Trucks. They are a forward control cab-over-engine type, where the driver sits in front of the axle. A flat front has two large windshields. The cab is very low-profile and has dual driving controls with a stand-up driving position on the right side. It is used in refuse service with front, side, and rear-loading refuse compactor bodies. Introduced in 2015 it remains in production in 2020.

<span class="mw-page-title-main">Mack Anthem</span>

The Mack Anthem is a series of heavy duty trucks built by Mack Trucks. It has a long low-drag hood and fenders. Introduced in 2018, it is designed primarily for highway use.

<span class="mw-page-title-main">Mack MD</span>

The Mack MD is a series of medium-duty trucks built by Mack Trucks. It has a short, low-profile hood and a high-visibility cab. It is designed as straight trucks for local delivery, construction, and other vocational jobs. The MD was introduced in February 2020 entered full production in July 2020.

References

  1. "TerraPro specifications". Mack Trucks. 2020. Retrieved January 14, 2021.
  2. "MP7". Mack Trucks. 2020. Retrieved January 14, 2021.
  3. Mack MP Engine Series MP7 & MP8. Mack Trucks. 2007. Retrieved December 28, 2020.
  4. L9N sales brochure (PDF). Cummins Westport. 2018. Retrieved January 15, 2021.
  5. "Mack Transmissions". Mack Trucks. 2020. Retrieved December 28, 2020.