Marquois scales (also known as Marquois parallel scales or Marquois scale and triangle or military scales) are a mathematical instrument that found widespread use in Britain, particularly in military surveying, from the late 18th century to World War II. [1]
Invented around 1778 by Thomas Marquois, the Marquois scales consist of a right-angle triangle (with sides at a 3:1 ratio) and two rulers (each with multiple scales). [2] The system could be used to aid precision when marking distances off scales, and to rapidly draw parallel lines a precise distance apart. [3] Quick construction of precise parallel lines was useful in cartography and engineering (especially before the availability of graph paper) and Marquois scales were convenient in some challenging environments where larger equipment like a drawing board and T-square was impractical, such as field survey work and classrooms. [4] Marquois scales fell out of favour among draftsmen in the early 20th century, [5] although familiarity with their use was an entry requirement for the Royal Military Academy at Woolwich around the same time. [4]
Marquois scales were normally made of boxwood, though sets were sometimes made in ivory [6] or metal.
The triangle would be used for many regular set square operations, the rulers likewise would function as rulers, but the unique function was the 3:1 reduction ratio between measured distance and drawn line. [2] [3] : 210–214
A line is drawn along the beveled edge (the side of middle-length) of the triangle. By placing a ruler against the hypotenuse of the triangle and sliding the triangle along the ruler for 3 units of the ruler's scale, drawing another line along the beveled edge results in a parallel line with a distance of only 1 unit from the original line. [2] Using larger distances on a ruler to draw lines smaller distances apart means that margin of error reading off the scale is reduced. Additionally, the end-state is the instruments already in place to slide the triangle again to quickly draw additional lines as desired. [2] [3] : 210–214
Regular set square triangles differ (from a Marquois scales triangle) by being made and used according to the angles of their triangle (eg 45-45-90 or 30-60-90 degrees) rather than according to the ratio between the lengths of their sides. Likewise the scales on other rulers are usually intended to be used directly and the selection differs accordingly. [2] [3] : 182, 210–214
Euclidean geometry is a mathematical system attributed to ancient Greek mathematician Euclid, which he described in his textbook on geometry; Elements. Euclid's approach consists in assuming a small set of intuitively appealing axioms (postulates) and deducing many other propositions (theorems) from these. Although many of Euclid's results had been stated earlier, Euclid was the first to organize these propositions into a logical system in which each result is proved from axioms and previously proved theorems.
Geometry arose as the field of knowledge dealing with spatial relationships. Geometry was one of the two fields of pre-modern mathematics, the other being the study of numbers (arithmetic).
Technical drawing, drafting or drawing, is the act and discipline of composing drawings that visually communicate how something functions or is constructed.
In geometry, straightedge-and-compass construction – also known as ruler-and-compass construction, Euclidean construction, or classical construction – is the construction of lengths, angles, and other geometric figures using only an idealized ruler and a pair of compasses.
In elementary geometry, two geometric objects are perpendicular if their intersection forms right angles at the point of intersection called a foot. The condition of perpendicularity may be represented graphically using the perpendicular symbol, ⟂. Perpendicular intersections can happen between two lines, between a line and a plane, and between two planes.
Angle trisection is a classical problem of straightedge and compass construction of ancient Greek mathematics. It concerns construction of an angle equal to one third of a given arbitrary angle, using only two tools: an unmarked straightedge and a compass.
An engineering drawing is a type of technical drawing that is used to convey information about an object. A common use is to specify the geometry necessary for the construction of a component and is called a detail drawing. Usually, a number of drawings are necessary to completely specify even a simple component. The drawings are linked together by a master drawing or assembly drawing which gives the drawing numbers of the subsequent detailed components, quantities required, construction materials and possibly 3D images that can be used to locate individual items. Although mostly consisting of pictographic representations, abbreviations and symbols are used for brevity and additional textual explanations may also be provided to convey the necessary information.
In trigonometry and geometry, triangulation is the process of determining the location of a point by forming triangles to the point from known points.
A compass, more accurately known as a pair of compasses, is a technical drawing instrument that can be used for inscribing circles or arcs. As dividers, it can also be used as a tool to mark out distances, in particular, on maps. Compasses can be used for mathematics, drafting, navigation and other purposes.
A protractor is a measuring instrument, typically made of transparent plastic or glass, for measuring angles.
John Farey Jr. was an English mechanical engineering, consulting engineer and patent agent, known for his pioneering contributions in the field of mechanical engineering.
A hypsometer is an instrument for measuring height or elevation. Two different principles may be used: trigonometry and atmospheric pressure.
The term Jacob's staff is used to refer to several things, also known as cross-staff, a ballastella, a fore-staff, a ballestilla, or a balestilha. In its most basic form, a Jacob's staff is a stick or pole with length markings; most staffs are much more complicated than that, and usually contain a number of measurement and stabilization features. The two most frequent uses are:
Stadiametric rangefinding, or the stadia method, is a technique of measuring distances with a telescopic instrument. The term stadia comes from a Greek unit of length Stadion which was the typical length of a sports stadium of the time. Stadiametric rangefinding is used for surveying and in the telescopic sights of firearms, artillery pieces, or tank guns, as well as some binoculars and other optics. It is still widely used in long-range military sniping, but in many professional applications it is being replaced with microwave, infrared, or laser rangefinding methods. Although much easier to use, electronic rangefinders can give away the shooter's position to a well-equipped adversary, and the need for accurate range estimation existed for much longer than electronic rangefinders small and rugged enough to be suitable for military use.
The sector, also known as a proportional compass or military compass, was a major calculating instrument in use from the end of the sixteenth century until the nineteenth century. It is an instrument consisting of two rulers of equal length joined by a hinge. A number of scales are inscribed upon the instrument which facilitate various mathematical calculations. It was used for solving problems in proportion, multiplication and division, geometry, and trigonometry, and for computing various mathematical functions, such as square roots and cube roots. Its several scales permitted easy and direct solutions of problems in gunnery, surveying and navigation. The sector derives its name from the fourth proposition of the sixth book of Euclid, where it is demonstrated that similar triangles have their like sides proportional. Some sectors also incorporated a quadrant, and sometimes a clamp at the end of one leg which allowed the device to be used as a gunner's quadrant.
Drafting tools may be used for measurement and layout of drawings, or to improve the consistency and speed of creation of standard drawing elements. Tools such as pens and pencils mark the drawing medium. Other tools such as straight edges, assist the operator in drawing straight lines, or assist the operator in drawing complicated shapes repeatedly. Various scales and the protractor are used to measure the lengths of lines and angles, allowing accurate scale drawing to be carried out. The compass is used to draw arcs and circles. A drawing board was used to hold the drawing media in place; later boards included drafting machines that sped the layout of straight lines and angles. Tools such as templates and lettering guides assisted in the drawing of repetitive elements such as circles, ellipses, schematic symbols and text. Other auxiliary tools were used for special drawing purposes or for functions related to the preparation and revision of drawings. The tools used for manual technical drawing have been displaced by the advent of computer-aided drawing, drafting and design (CADD).
A speed square, also called a rafter square, rafter angle square, and triangle square, is a multi-purpose triangular carpenters' tool use for marking out. Its functions include many of those of a combination square, try square, and framing square. Carpenters use it to make basic measurements and mark lines on dimensional lumber, and as a saw guide for short 45 and 90 degree cuts.
The quadratrix or trisectrix of Hippias is a curve which is created by a uniform motion. It is one of the oldest examples for a kinematic curve. Its discovery is attributed to the Greek sophist Hippias of Elis, who used it around 420 BC in an attempt to solve the angle trisection problem. Later around 350 BC Dinostratus used it in an attempt to solve the problem of squaring the circle.
A schema for horizontal dials is a set of instructions used to construct horizontal sundials using compass and straightedge construction techniques, which were widely used in Europe from the late fifteenth century to the late nineteenth century. The common horizontal sundial is a geometric projection of an equatorial sundial onto a horizontal plane.
Vertical declining dials are sundials that indicate local apparent time. Vertical south dials are a special case: as are vertical north, vertical east and vertical west dials. The word declining means that the wall is offset from one of these 4 cardinal points. There are dials that are not vertical, and these are called reclining dials.