Military radio antenna kites

Last updated
A "King" kite used by the U.S. Signal Corps. Kite used by the Signal Corps.jpg
A "King" kite used by the U.S. Signal Corps.

Radio antenna kites are used to carry a radio antenna aloft, higher than is practical with a mast. They are most often associated with portable radio systems, usually with pre-World War I field equipment, and were also occasionally used to increase radio range on Naval ships. The use of kite supported antennae was limited because of difficulty in maintaining consistent antenna height, unpredictability of the wind, and improvements in radio antenna, transmission, and reception. During World War II and after they were used in conjunction with survival radios issued to aircraft flying over-water missions.

Contents

History

King Kite, Fort Leavenworth, Kansas c. 1905 King kite.jpg
King Kite, Fort Leavenworth, Kansas c. 1905

Before their radio use, kites were used by the United States and other nations' armed forces for observation, aerial photography, and signaling. They were used non-militarily to hoist radio antennae at least since 1898 when Greenleaf Whittier Pickard used a small box kite, normally used for meteorological observations, to raise a wire half a mile up for wireless tests at the Blue Hill Meteorological Observatory in Milton, Massachusetts. [1]

On December 12, 1901 Guglielmo Marconi sent the first transatlantic radio signal from Poldhu, Cornwall, England, to St. Johns, Newfoundland. The antenna at St. John's was carried by a Baden-Powell Levitor kite, designed by Baden Baden-Powell as a man-carrying observation kite.

The King kite

The first kite used by the United States Army Signal Corps specifically for raising an antenna was designed and built by Sergeant Thomas I. King, Signal Corps Company A, while stationed at Fort Leavenworth, Kansas, in 1905. The “King” kite was large, 7 feet high and 5 feet wide, made of 15 yards of white Japanese silk on a bamboo frame, and weighed less than 2 pounds. [2] Similar to Silas J. Conyne's kite of 1902, [3] it had a diamond shape with a squared-off top and bottom, keel, and large opening in the center to give it some of the stability of a box kite. It was used either singly or in trains of 2 to 4 kites or, on less windy days, in conjunction with a balloon to provide extra lift.

The King kite was used with small portable spark-gap transmitters, and the elevated antenna made little improvement in the distance signals could be transmitted. It did significantly improve in receiving, and signals could be heard from as far away as Cuba on a receiver using an electrolytic detector. [4]

Experiments with Bell tetrahedral kites

Tetrahedral kite built by Alexander Graham Bell being used to lift a radio antenna, 1906. Bell tetrahedral antenna kite.jpg
Tetrahedral kite built by Alexander Graham Bell being used to lift a radio antenna, 1906.

In the spring of 1906 Alexander Graham Bell and Lee deForest teamed up to experiment with Dr. Bell's tetrahedral kites as antenna lifters. Bell had been experimenting with kites in hopes of developing a flying machine. A large, 230 cell kite was used to lift an antenna 400 feet into the air at a station near Fort Myer, Virginia. Signals were successfully sent and received by the Naval wireless telegraph station at the Washington Navy Yard. [5] The message was sent by retired General Henry Harrison Chase Dunwoody, who was working for deForest at the time.

KI-1, KI-2 and KI-3 kites

The United States Signal Corps for a time maintained three models of antenna lifting kites as standard equipment. They were listed in the Signal Corps Storage Catalogue as late as 1920.

Kite KI-1, formerly designated the "folding Malay kite", was made of spruce rods glued and wired together, covered with cloth, measuring 60 by 60 inches. It was used with portable field wireless sets.

The King kite, somewhat modified, was renamed and became standard Signal Corps equipment, available in two types. Kite KI-2 was the smaller at 6 feet high by 6 feet wide, while KI-3 was 7 1/2 by 7 1/2. Both had spruce sticks with a rim of 32 gauge stranded wire, with a covering of "light slate-colored percale". They were intended for use with the SCR-44 field wireless set, a pre-World War I pack set, something still specified in the 1920 Storage Catalogue despite the SCR-44 being obsolete, and listed as so in the same Storage Catalogue. [6]

Army and navy experiments

Kites built to raise signal flags and radio antennae, First Company, Signal Corps, National Guard of New York, 1907. Kites 1st Co Signal Corps.jpg
Kites built to raise signal flags and radio antennae, First Company, Signal Corps, National Guard of New York, 1907.

The British Royal Navy experimented with kite raising antennae on HMS Good Hope in 1903, using a box kite designed by Samuel Franklin Cody. A 300-foot kite raised antenna increased their radio range from 60 or 70 miles to 110 miles. [7] The United States Navy conducted kite antenna experiments on the torpedo boats USS Stringham and USS Bailey in 1911. [8]

Some Signal Corps units conducted kite antenna experiments independently, often constructing their own kites. In June 1907 the First Company, Signal Corps, National Guard of New York, made box, Malay and hexagon shaped kites, to experiment with raising standard international code flag signals and radio antennae. [9]

In 1915 Adjutant General of Massachusetts Charles H. Cole, after hearing that the German ship Prinz Eitel Friedrich had good results using kites to suspend a radio antenna, decided to experiment with kite supported antennae himself. He asked Samuel F. Perkins, a manufacturer of man lifting kites, to assist with the tests at the July maneuvers of the Massachusetts National Guard. Perkins' original configuration, four kites in a chain with an antenna leading from the ground to some point on the kites' tether, swayed up and down considerably, causing the antenna to vary in length, and making tuning difficult. This had been a problem since kites were used for raising antennae, and had all but forced their abandonment after the early experimental years. Perkins was able to solve the problem easily by attaching the antenna at a height corresponding to the kites' lowest position when swaying normally. The antenna itself acted as a tether and kept the kite's string from rising between the point of attachment and the ground. The kite was still able to rise and fall, but only the part of the string between the antenna and the kite itself could rise, and the antenna remained a constant length. [10] The tests were considered a success, and messages sent using a field wireless set with the kite antenna were heard 150 miles away, where the same set could transmit only 25 miles normally. [11]

Emergency radios

Early emergency radio use

The United States Navy experimented with kites for emergency radio use as early as 1922 when Commander Taylor and Lieutenant C. D. Palmer of the Anacostia Air Station Radio Laboratory designed kites to lift antenna for radios in downed seaplanes. The aircraft of the day had trailing antenna that only functioned while in flight. Two kites were issued, one for stronger and the other for lighter winds, as well as a reel of light antenna wire and a small generator that could be placed in the air stream of a functioning engine to power the radio. [12]

Kites M-277-A and M-357-A

In 1941 the German military issued the NSG2 or "Notsender" emergency radio for use in lifeboats. It included a winged box kite to raise the antenna. An NSG2 was captured by the British in 1941 and copied as the "Dinghy Transmitter" T-1333. At first the British used a box kite with the set, but by 1943 were using a kite, similar to Silas J. Conyne's 1911 design, [13] that could be launched by a Very pistol.

A second captured NSG2 was brought to the American army by the British, improved on and issued as the SCR-578-A "Gibson Girl" survival radio in 1942. It was carried by United States Army Air Forces aircraft and intended for use in life rafts. It included the M-277-A collapsible box kite to raise the antenna, which was also included in some of the later SCR-578-B sets. It was similar to the kite included with the NSG2 but did not include the wings. The 17 x 17 x 36 inch frame of the M-277-A was made up of 4 aluminum rods, each rod end was attached at the ends by a hinge to 4 shorter rods, and each of these met in the middle, attached by a locking mechanism, so that the whole thing could be opened up like an umbrella. The yellow cloth was treated with water repellent and part of one section filled with kapok to add buoyancy if it fell into the water. [14] It was designed to be simple to assemble, and could fly in winds from 7 to 40 miles per hour. It packed into a cardboard tube, on which were also printed the assembly instructions.

Kite M-357-A is identical to M-277-A except that the frame could be separated into two pieces, the four main rods attached in their centers by ferrules. The whole thing could be stored in a space 2 by 4 by 19 inches. Instructions for assembly were printed on the upper cloth. M-357-A was issued with the SCR-578-B (some sets included the remaining stock of M-277-A) and the post-war AN/CRT-3, still in use in the early 1970s.

Both kites had two bridle attachment points, one for winds 7–20 miles per hour, the other for 15–40 miles per hour. The SCR-578 and AN/CRT-3 also included a small balloon and hydrogen generator to raise the antenna if there was no wind, however, because the hydrogen generator was caustic and the hydrogen flammable, the kite was the preferred method.

M-277-A.jpg M-357-A kite.jpg M-357-A instructions.jpg
M-277-AM-357-AInstructions for assembling M-357-A

Related Research Articles

<span class="mw-page-title-main">Kite aerial photography</span> Type of photography

Kite aerial photography (KAP) is a type of photography. A camera is lifted using a kite and is triggered either remotely or automatically to take aerial photographs. The camera rigs can range from the extremely simple, consisting of a trigger mechanism with a disposable camera, to complex apparatus using radio control and digital cameras. On some occasions it can be a good alternative to other forms of aerial photography.

<span class="mw-page-title-main">SCR-270</span> Early U.S. Army radar type that detected Pearl Harbor attack

The SCR-270 was one of the first operational early-warning radars. It was the U.S. Army's primary long-distance radar throughout World War II and was deployed around the world. It is also known as the Pearl Harbor Radar, since it was an SCR-270 set that detected the incoming raid about 45 minutes before the December 7, 1941, attack on Pearl Harbor commenced.

<span class="mw-page-title-main">Frank Conrad</span> American electrical engineer and radio pioneer

Frank Conrad was an American electrical engineer, best known for radio development, including his work as a pioneer broadcaster. He worked for the Westinghouse Electrical and Manufacturing Company in East Pittsburgh, Pennsylvania, for half a century. His experimental radio station provided the inspiration, and he acted in an advisory role, for the establishment of Westinghouse's first broadcasting service, over radio station KDKA.

<span class="mw-page-title-main">Camp Evans Historic District</span> Historic district in New Jersey, United States

Camp Evans Historic District is an area of the Camp Evans Formerly Used Defense Site in Wall Township, New Jersey. The site of the military installation is noted for a 1914 transatlantic radio receiver and various World War II/Cold War laboratories of the United States Army. It was designated a National Historic Landmark District in 2012, in recognition of the site's long role in the development of modern civilian and military electronic communications.

<span class="mw-page-title-main">SCR-268 radar</span> U.S. Armys first radar system

The SCR-268 was the United States Army's first radar system. Introduced in 1940, it was developed to provide accurate aiming information for antiaircraft artillery and was also used for gun laying systems and directing searchlights against aircraft. The radar was widely utilized by both Army and Marine Corps air defense and early warning units during World War II. By the end of World War II the system was already considered out of date, having been replaced by the much smaller and more accurate SCR-584 microwave-based system.

<span class="mw-page-title-main">Invention of radio</span> Engineering detection and transmission of Radio Waves

The invention of radio communication was preceded by many decades of establishing theoretical underpinnings, discovery and experimental investigation of radio waves, and engineering and technical developments related to their transmission and detection. These developments allowed Guglielmo Marconi to turn radio waves into a wireless communication system.

<span class="mw-page-title-main">SCR-584 radar</span> Automatic tracking microwave radar.

The SCR-584 was an automatic-tracking microwave radar developed by the MIT Radiation Laboratory during World War II. It was one of the most advanced ground-based radars of its era, and became one of the primary gun laying radars used worldwide well into the 1950s. A trailer-mounted mobile version was the SCR-784.

<span class="mw-page-title-main">SCR-536</span> U.S. WWII hand-held military radio

The SCR-536 was a hand-held radio transceiver used by the US Army Signal Corps in World War II. It is popularly referred to as a walkie talkie, although it was originally designated a "handie talkie".

<span class="mw-page-title-main">Signal Corps Radio</span> U.S. Army radio systems

Signal Corps Radios were U.S. Army military communications components that comprised "sets". Under the Army Nomenclature System, the abbreviation SCR initially designated "Set, Complete Radio", but was later misinterpreted as "Signal Corps Radio."

<span class="mw-page-title-main">SCR-299</span>

The SCR-299 was a U.S. Signal Corps mobile military communications unit used during World War II.

<span class="mw-page-title-main">Mahlon Loomis</span> American inventor of radio

Mahlon Loomis was an American dentist and inventor known for proposing a wireless communication and electric power generating system based on his idea that there were electrically charged layers in the Earth's atmosphere.

<span class="mw-page-title-main">Survival radio</span> Small radios carried to facilitate rescue in an emergency

Survival radios are carried by pilots and search and rescue teams to facilitate rescue in an emergency. They are generally designed to transmit on international distress frequencies. Maritime systems have been standardized under the Global Maritime Distress Safety System. Civil and military organisation's utilized different frequencies to communicate and no infringement on either sector would take place. For emergencies involving civilian aircraft, the radio frequency used is VHF 121.5 MHz and for military aircraft incidents, the frequency used is UHF 243 MHz.

<span class="mw-page-title-main">SCR-300</span> WWII United States military portable radio transceiver

The SCR-300 was a portable radio transceiver used by US Signal Corps in World War II. This backpack-mounted unit was the first radio to be nicknamed a "walkie talkie".

The AN/MRN-1 was an instrument approach localizer used by the Army Air Force during and after World War II. It was standardized on 3 July 1942. It replaced the SCR-241, and was a component of SCS-51.

The AN/MRN-3 was a marker beacon set used by the Army Air Force during and after World War II, it was standardized 23 October 1943, and replaced SCR-241.

The SCR-68 was a military radiotelephone used by the US Army Signal Corps as an aircraft radio in the waning months of World War I. Due to its many problems, primarily its inability to communicate with other radios, like its ground component the SCR-67 or the larger truck mounted SCR-108, over large distances, the SCR-68 quickly became obsolete. Nonetheless, the SCR-68 was one of the first steps towards developing more effective messaging between pilots and commanders, even beyond military usage.

<span class="mw-page-title-main">SCR-508</span> WW2-era US Army radio

The SCR-508 radio was a mobile Signal Corps Radio used by the U.S. Army during World War II, for short range ground communications. The SCR-508 series radio represented the Army's commitment to both FM and crystal tuning, and was used extensively by armor and mechanized units. The turret bustle of late series light and medium tanks was designed around this radio.

<span class="mw-page-title-main">Bellini–Tosi direction finder</span> Type of radio direction finder

A Bellini–Tosi direction finder is a type of radio direction finder (RDF), which determines the direction to, or bearing of, a radio transmitter. Earlier RDF systems used very large rotating loop antennas, which the B–T system replaced with two fixed antennae and a small rotating loop, known as a radiogoniometer. This made RDF much more practical, especially on large vehicles like ships or when using very long wavelengths that demand large antennae.

<span class="mw-page-title-main">SCR-54</span> Crystal radio receiver

The SCR-54 was a tunable, portable crystal radio receiver used by the U. S. Army during World War I for fire control in conjunction with airplanes.

<span class="mw-page-title-main">SCR-602</span> US mobile early-warning radar during WWII

The SCR-602 also known as the AN/TPS-3, was a mobile, lightweight, medium-range, early-warning radar utilized by the United States and its allies during World War II. The radar was originally designed for use during the initial stages of an amphibious assault or military operation where its lightweight relative to other radar systems was a distinct advantage. Once larger radars such as the SCR-270 or AN/TPS-1 came online the SCR-602 could also be used to fill in gaps in radar coverage.

References

  1. Greenleaf Whittier Pickard to George H. Clark, May 26, 1931. George H, Clark Radioana Collection, Smithsonian Institution.
  2. "Trying White Silk Kites at Leavenworth". Topeka Daily Capital. October 10, 1905.
  3. Conyne, Silas J. (Apr 29, 1902), Aeroplane. , retrieved 2016-04-29
  4. "Wireless Message Sent 2,500 Miles Through Air". Lincoln Evening News. November 9, 1905.
  5. "Kites Get Messages". Washington Post. March 28, 1906.
  6. United States Army Signal Corps (1920). Signal Corps Storage Catalogue. U.S. Government Printing Office.
  7. The Electrical Engineer. 1903-08-28. p. 309.
  8. Report of the Chief of the Bureau of Steam Engineering for 1911.
  9. New York (State) Adjutant General's Office (1908). Annual Report of the Adjutant-General of the State of New York for the Year 1907.
  10. Popular Science. Vol. 89. 1916-10-01. p. 630.
  11. Naval Institute Proceedings. United States Naval Institute. September 1915. p. 1667.
  12. Aviation. McGraw-Hill Publishing Company. 1922-03-27. p. 374.
  13. Conyne, Silas J. (Oct 17, 1911), Kite. , retrieved 2016-04-29
  14. United States War Department (1944). Handbook of maintenance instructions for radio set SCR-578-A or SCR-578-B. OCLC   220742323.