Muzzleloader

Last updated
A "Brown Bess" muzzle-loading musket, used by the British Army from 1722 to 1838 British Military Short Land Pattern Musket.jpg
A "Brown Bess" muzzle-loading musket, used by the British Army from 1722 to 1838

A muzzleloader is any firearm in which the user loads the projectile and the propellant charge into the muzzle end of the gun (i.e., from the forward, open end of the gun's barrel). This is distinct from the modern designs of breech-loading firearms, in which user loads the ammunition into the breech end of the barrel. The term "muzzleloader" applies to both rifled and smoothbore type muzzleloaders, and may also refer to the marksman who specializes in the shooting of such firearms. The firing methods, paraphernalia and mechanism further divide both categories as do caliber (from cannons to small-caliber palm guns).

Contents

Modern muzzleloading firearms range from reproductions of sidelock, flintlock and percussion long guns, to in-line rifles that use modern inventions such as a closed breech, sealed primer and fast rifling to allow for considerable accuracy at long ranges.

Modern mortars use a shell with the propelling charge and primer attached at the base. Unlike older muzzleloading mortars, which were loaded the same way as muzzleloading cannon, the modern mortar is fired by dropping the shell down the barrel where a pin fires the primer, igniting the main propelling charge. Both the modern mortar and the older mortar were used for high angle fire. However, the fact that the mortar is not loaded in separate steps may make its definition as a muzzleloader a matter of opinion.

Muzzleloading can apply to anything from cannons to pistols but in modern parlance the term most commonly applies to black powder small arms. It usually, but not always, involves the use of a loose propellant (i.e., gunpowder) and projectile, as well as a separate method of ignition or priming.

Loading

Loaded muzzleloading cannon. (1) Priming charge (2) Main propellant charge (3) Wadding (4) Projectile (5) Wadding CMM - Przekroj mozdzierza.JPG
Loaded muzzleloading cannon. (1) Priming charge (2) Main propellant charge (3) Wadding (4) Projectile (5) Wadding
Wadding recovered from the wreck of the packet ship Hanover and was found inside a loaded cannon, National Maritime Museum Cornwall (2014) Hanover, Falmouth Packet, wadding from loaded cannon.JPG
Wadding recovered from the wreck of the packet ship Hanover and was found inside a loaded cannon, National Maritime Museum Cornwall (2014)

In general, the sequence of loading is to put in first gunpowder, by pouring in a measured amount of loose powder, historically mostly by using a powder flask (or powder horn), or by inserting a pre-measured bag or paper packet of gunpowder (called a cartridge) or by inserting solid propellant pellets. The gunpowder used is typically black powder or black powder substitutes like Pyrodex. Sometimes two types of gunpowder (and two flasks) were used consisting of finer priming powder for the flash pan and coarser powder for the main charge behind the ball. This was particularly the case with earlier muzzleloaders like matchlocks but appear to have been less common with flintlocks and was irrelevant with percussion locks since they used percussion caps rather than priming powder.

Wadding is made from felt, paper, cloth or card and has several different uses. In shotguns, a card wad or other secure wadding is used between the powder and the shot charge to prevent pellets from dropping into the powder charge and on top of the shot charge to hold it in place in the barrel. In smooth bore muskets and most rifles used prior to cartridges being introduced in the mid-to late nineteenth century, wadding was used primarily to hold the powder in place.

On most naval cannons, one piece of wadding was used to hold the powder in place and served the purpose of creating a better seal around the shot. Another was used to act as a plug to stop the shot rolling out because of the swaying of the ship.

The use of cartridges with both gunpowder charge and ball, made up in batches by the shooter or a servant, was known from very early on, but until roughly around 1800 loading using a powder flask and a bag of balls was more common outside of the military. The measuring stage for the barrel charge of gunpowder could be avoided by carrying a number of pre-measured charges in small containers of wood, metal or cloth, often carried on a bandolier. These were known by various names, including "chargers" or "apostles" as 12 were often carried. For most of the time muzzleloaders were in use, a round ball and pre-measured powder charge could be carried in a paper or cloth wrapping. The shooter would bite off the end of the paper cartridge with his teeth and pour the powder into the barrel followed by the ball encased in the paper wrapping.

The projectiles and wads were then pushed down into the breech with a ramrod until they were firmly seated on the propellant charge. Priming powder could be carried in a separate priming flask and poured into the priming pan or a little powder from the cartridge was used, and the frizzen was pushed down to hold the priming powder in place. After the gunpowder and projectile or shot charge were placed in the barrel a ramrod was used to firmly pack everything down at the base of the barrel. Then either a priming charge was placed in the priming pan or a percussion cap was placed on the nipple, the firing mechanism initiated; the cock or hammer was then cocked to make the firearm ready to fire.

Projectile types and history

A pair of French rifled, flintlock, duelling pistols by Nicolas Noel Boutet 1794-1797. Royal Ontario Museum, Toronto, Canada. The set of accessories includes a small hammer as rifled pistols used slightly oversized bullets; a hammer was needed to drive the bullet down the barrel when loading. French cased duelling pistols, Nicolas Noel Boutet, single shot, flintlock, rifled, .58 caliber, blued steel, Versailles, 1794-1797 - Royal Ontario Museum - DSC09477.jpg
A pair of French rifled, flintlock, duelling pistols by Nicolas Noël Boutet 1794–1797. Royal Ontario Museum, Toronto, Canada. The set of accessories includes a small hammer as rifled pistols used slightly oversized bullets; a hammer was needed to drive the bullet down the barrel when loading.

Muzzleloading firearms generally use round balls, cylindrical conical projectiles, and shot charges.

In some types of rifles firing round ball, a lubricated patch (see Kentucky rifle) of fabric is wrapped around a ball which is slightly smaller than the barrel diameter. In other types of round ball firing rifles, a ramrod and hammer is used to force the round ball down through the rifling. When fired, either the lead ball or the wrapping grips the rifling and imparts spin to the ball which usually gives improved accuracy. In rifles firing Minié balls, the patch, often the paper wrapping from the cartridge, is used as an initial seal and to hold powder in place during loading.

The Minié ball replaced the round ball in most firearms, especially for military use, in the 1840s and 1850s[ citation needed ]. It has a hollow base which expands to grip the rifling. The combination of the spinning Minié ball and the consistent velocity provided by the improved seal gave far better accuracy than the smoothbore muzzleloaders that it replaced.

Modern usage

When aiming for great accuracy, muzzle-loaders are usually cleaned ("swabbed") before reloading, so that there is no residue left in the barrel to reduce accuracy, though in competitions run by the international governing body, the MLAIC, this is prohibited for military rifle and musket events. However, in small arms muzzleloading rifles, swabbing is only done after every 5-10 shots. Large caliber muzzle-loaders such as cannons are always swabbed between shots to prevent accidents caused by live sparks igniting the fresh charge of powder as it is being loaded.

Muzzleloading

Varsity Scouts of the Boy Scouts of America learning about muzzleloading rifles VarsityScoutsBlackpowderShooting2004.jpg
Varsity Scouts of the Boy Scouts of America learning about muzzleloading rifles

Muzzleloading is the sport or pastime of firing muzzleloading guns. Muzzleloading guns, both antique and reproduction, are used for target shooting, hunting, historical re-enactment and historical research. The sport originated in the United States in the 1930s, just as the last original users and makers of muzzleloading arms were dying out. The sport received a tremendous boost in the 1960s and 1970s. The Muzzle Loaders Associations International Committee (www.MLAIC.org) was formed in 1970 and held its first World Championship in 1971. Since then a flourishing industry manufacturing working reproductions of historic firearms now exists in the United States and Europe, particularly in northern Italy, for example at Gardone Val Trompia, in the Province of Brescia. In the United States muzzleloading guns are, subject to a number of qualifications, generally not considered firearms. Subject to state law they may be possessed by persons who might otherwise not be legally allowed to own a firearm. [2]

The American National Muzzle Loading Rifle Association holds two national tournaments a year in Friendship, Indiana as well as the Western National Shoot Event held in Phoenix, Arizona.

The Muzzle Loaders Associations International Committee (MLAIC) governs international competition with muzzle-loading arms. The MLAIC holds a Short Range World Championship in even-numbered years and a Long Range World Championship (300–1,000 yd (270–910 m)) on odd numbered years (South Africa has won the last 5 Long Range World Championships).

Modern use

Driven by demand for muzzleloaders for special extended primitive hunting seasons, firearms manufacturers have developed in-line muzzleloading rifles with designs similar to modern breech-loading centerfire designs. [3] Knight Rifles pioneered the in-line muzzleloader in the mid-1980s, manufacturing and selling them to this day. [4] Savage Arms has created the 10ML-II, which can be used with smokeless powder, reducing the cleaning required. [5] However, Savage has discontinued the production of smokeless muzzleloaders. Remington Firearms also have a muzzleloader in production, the model "700 Ultimate" or "700 SL Ultimate". There are several custom gun makers that are currently building smokeless muzzleloaders on new or donor bolt actions. [6]

See also

Muzzle-loading gun on its carriage Grand Turk(28).jpg
Muzzle-loading gun on its carriage

Related Research Articles

<span class="mw-page-title-main">Firearm</span> Gun for an individual

A firearm is any type of gun that uses an explosive charge and is designed to be readily carried and used by an individual. The term is legally defined further in different countries.

<span class="mw-page-title-main">Rifle</span> Common long range firearm

A rifle is a long-barreled firearm designed for accurate shooting and higher stopping power, with a barrel that has a helical or spiralling pattern of grooves (rifling) cut into the bore wall. In keeping with their focus on accuracy, rifles are typically designed to be held with both hands and braced firmly against the shooter's shoulder via a buttstock for stability during shooting. Rifles have been used in warfare, law enforcement, hunting and target shooting sports.

<span class="mw-page-title-main">Single-shot</span> Firearm that holds one round of ammunition

In firearm designs, the term single-shot refers to guns that can hold only a single round of ammunition inside and thus must be reloaded manually after every shot. Compared to multi-shot repeating firearms ("repeaters"), single-shot designs have no moving parts other than the trigger, hammer/firing pin or frizzen, and therefore do not need a sizable receiver behind the barrel to accommodate a moving action, making them far less complex and more robust than revolvers or magazine/belt-fed firearms, but also with much slower rates of fire.

<span class="mw-page-title-main">Bullet</span> Projectile propelled by a firearm, sling, or air gun

A bullet is a kinetic projectile, a component of firearm ammunition that is shot from a gun barrel. They are made of a variety of materials, such as copper, lead, steel, polymer, rubber and even wax; and are made in various shapes and constructions, including specialized functions such as hunting, target shooting, training, and combat. Bullets are often tapered, making them more aerodynamic. Bullet size is expressed by weight and diameter in both imperial and metric measurement systems. Bullets do not normally contain explosives but strike or damage the intended target by transferring kinetic energy upon impact and penetration.

<span class="mw-page-title-main">Cartridge (firearms)</span> Pre-assembled firearm ammunition consisting of a casing, projectile, propellant, and primer

A cartridge, also known as a round, is a type of pre-assembled firearm ammunition packaging a projectile, a propellant substance and an ignition device (primer) within a metallic, paper, or plastic case that is precisely made to fit within the barrel chamber of a breechloading gun, for convenient transportation and handling during shooting. Although in popular usage the term "bullet" is often used to refer to a complete cartridge, the correct usage only refers to the projectile.

<span class="mw-page-title-main">Rifling</span> Grooves in a weapon barrel for accuracy

Rifling is the term for helical grooves machined into the internal surface of a firearms's barrel for imparting a spin to a projectile to improve its aerodynamic stability and accuracy. It is also the term for creating such grooves.

<span class="mw-page-title-main">Flintlock</span> Firearm with flint-striking ignition

Flintlock is a general term for any firearm that uses a flint-striking ignition mechanism, the first of which appeared in Western Europe in the early 16th century. The term may also apply to a particular form of the mechanism itself, also known as the true flintlock, that was introduced in the early 17th century, and gradually replaced earlier firearm-ignition technologies, such as the matchlock, the wheellock, and the earlier flintlock mechanisms such as the snaplock and snaphaunce.

<span class="mw-page-title-main">Breechloader</span> Class of gun which is loaded from the breech

A breechloader is a firearm in which the user loads the ammunition from the breech end of the barrel, as opposed to a muzzleloader, in which the user loads the ammunition from the (muzzle) end of the barrel.

<span class="mw-page-title-main">Smoothbore</span> Weapon that has a barrel without rifling

A smoothbore weapon is one that has a barrel without rifling. Smoothbores range from handheld firearms to powerful tank guns and large artillery mortars.

<span class="mw-page-title-main">Gun barrel</span> Firearm component which guides the projectile during acceleration

A gun barrel is a crucial part of gun-type weapons such as small firearms, artillery pieces, and air guns. It is the straight shooting tube, usually made of rigid high-strength metal, through which a contained rapid expansion of high-pressure gas(es) is used to propel a projectile out of the front end (muzzle) at a high velocity. The hollow interior of the barrel is called the bore, and the diameter of the bore is called its caliber, usually measured in inches or millimetres.

Internal ballistics, a subfield of ballistics, is the study of the propulsion of a projectile.

A rifled musket, rifle musket, or rifle-musket is a type of firearm made in the mid-19th century. Originally the term referred only to muskets that had been produced as a smoothbore weapon and later had their barrels replaced with rifled barrels. The term later included rifles that directly replaced, and were of the same design overall as, a particular model of smoothbore musket.

This article explains terms used for the British Armed Forces' ordnance (weapons) and ammunition. The terms may have different meanings depending on its usage in another country's military.

<span class="mw-page-title-main">M1819 Hall rifle</span> Rifle

The M1819 Hall rifle was a single-shot breech-loading rifle designed by John Hancock Hall, patented on May 21, 1811, and adopted by the U.S. Army in 1819. It was preceded by the Harpers Ferry M1803. It used a pivoting chamber breech design and was made with either flintlock or percussion cap ignition systems. The years of production were from the 1820s to the 1840s at the Harpers Ferry Arsenal. This was the first breech-loading rifle to be adopted in large numbers by any nation's army, but not the first breech-loading military rifle – the Ferguson rifle was used briefly by the British Army in the American Revolutionary War. The Hall rifle remained overshadowed by common muskets and muzzleloading rifles which were still prevalent until the Civil War. The early flintlocks were mostly converted to percussion ignition.

A muzzle-loading rifle is a muzzle-loaded small arm or artillery piece that has a rifled barrel rather than a smoothbore. The term "rifled muzzle loader" typically is used to describe a type of artillery piece, although it is technically accurate for small arms as well. A shoulder arm is typically just called a "rifle", as almost all small arms were rifled by the time breechloading became prevalent. Muzzle and breechloading artillery served together for several decades, making a clear distinction more important. In the case of artillery, the abbreviation "RML" is often prefixed to the guns designation; a Rifled breech loader would be "RBL", or often just "BL", since smoothbore breechloading artillery is almost nonexistent. A muzzle loading weapon is loaded through the muzzle, or front of the barrel. This is the opposite of a breech-loading weapon or rifled breechloader (RBL), which is loaded from the breech-end of the barrel. The rifling grooves cut on the inside of the barrel cause the projectile to spin rapidly in flight, giving it greater stability and hence range and accuracy than smoothbore guns. Hand held rifles were well-developed by the 1740s. A popularly recognizable form of the "muzzleloader" is the Kentucky Rifle, which was actually developed in Pennsylvania. The American Longrifle evolved from the German "Jäger" rifle.

<span class="mw-page-title-main">Armstrong gun</span> British artillery piece

An Armstrong gun was a uniquely designed type of rifled breech-loading field and heavy gun designed by Sir William Armstrong and manufactured in England beginning in 1855 by the Elswick Ordnance Company and the Royal Arsenal at Woolwich. Such guns involved a built-up gun construction system of a wrought-iron tube surrounded by a number of wrought-iron strengthening coils shrunk over the inner tube to keep it under compression.

The following are terms related to firearms and ammunition topics.

<span class="mw-page-title-main">4 bore</span> Black powder hunting caliber

Four bore or 4 bore is a black powder caliber of the 19th century, used for the hunting of large and potentially dangerous game animals. The specifications place this caliber between the larger 2 bore and the smaller 6 bore rifles. This caliber was the quintessential elephant gun caliber of the black powder safari rifles. The caliber was also used for the Coffman cartridges used for starting large aero engines such as the Rolls-Royce Griffon as used in the later Marks of Supermarine Spitfire.

The 6 bore, also known as the 6 gauge, is an obsolete caliber that was used commonly in 19th-century black-powder firearms.

<span class="mw-page-title-main">68-pounder gun</span> Naval gun

The 68-pounder cannon was an artillery piece designed and used by the British Armed Forces in the mid-19th century. The cannon was a smoothbore muzzle-loading gun manufactured in several weights, the most common being 95 long cwt (4,800 kg), and fired projectiles of 68 lb (31 kg). Colonel William Dundas designed the 112 cwt version in 1841 and it was cast the following year. The most common variant, weighing 95 cwt, dates from 1846. It entered service with the Royal Artillery and the Royal Navy and saw active service with both arms during the Crimean War. Over 2,000 were made and it gained a reputation as the finest smoothbore cannon ever made.

References

  1. Jeff Kinard (2003). Pistols: An Illustrated History of Their Impact. ABC-CLIO. pp. 33–34. ISBN   978-1-85109-470-7.
  2. ATF.gov Top 10 Frequently Asked Firearms Questions and Answers
  3. "In-line Muzzleloaders". Field & Stream. No. Nov 1996. November 1996. Retrieved 11 July 2020.
  4. Jim Braaten (3 June 2009), "Knight Muzzleloading Rifles looks to close production", Minneapolis Star Tribune, archived from the original on 11 May 2015
  5. "Hunting drives today's blackpowder market". Shooting Industry. May 2004. Archived from the original on 2012-07-18.
  6. McClintock, Brian (February 10, 2011). "The Modernization of the Muzzleloaded Rifle". Popular Mechanics . Archived from the original on January 30, 2018.