The Santa Fe Railroad tugboats were used by the Atchison, Topeka and Santa Fe Railway to barge rail cars across the San Francisco Bay for much of the 20th century, as there is no direct rail link to the San Francisco peninsula. In the post World War II period, a fleet of three tugs moved the barges: the Paul P. Hastings, the Edward J. Engel, and the John R. Hayden. After cross-bay float service had ended and the tugs had been sold, the Hastings sank off Point Arena, California in 1992, in water too deep to raise. The Engel sank off Alameda, California in 2007 and was raised and scrapped in the winter of 2013-14. The Hayden remains afloat and in service in Oregon.
Transportation patterns changed with time. Piggy-back truck service increased as direct railcar service declined. The Chronicle at the urging of the railroad[1][unreliable source?] switched to piggy-back truck delivery. As the use of the cross-bay float service declined Santa Fe reduced the tug fleet. The Engel was sold in 1969,[2] and the Hayden was sold in 1976. The Hastings continued as the only tug until 1984. On May 4, 1984, a fire at the Richmond ferry slip killed cross-bay float service, and the Hastings was sold.
The final route for the cross-bay service went from the ferry slip in Richmond, California on the east side of the bay to China Basin on the west side of the bay. China Basin is on the San Francisco Peninsula just south of the San Francisco–Oakland Bay Bridge. The 10.4-mile (16.7km) voyage usually took about an hour and twenty minutes each way.[4]
History of the tugboat fleet
Before World War II
Prior to the end of World War II there were five tugs used on San Francisco Bay at various times:[5]
Richmond, built new for the Santa Fe by Fulton Iron Works in 1899. Sold to Crowley Tugboat Company in December 1925.[6]
A.H. Payson, built new for the Santa Fe in 1902 by Boole & Sons, Oakland CA. She remained in Santa Fe service its entire life, retired in 1948[6] and was sold for scrap in 1950.
E.P. Ripley, built new for the Santa Fe in 1907 by Kruse & Banks, North Bend OR,[6] also sold for scrap in 1950. Ripley was president of the railroad from 1896-1920.
W.B. Storey, built in Elizabeth, New Jersey, in 1919 as Basford[7] by Bethlehem Steel, was purchased used by the Santa Fe in August 1923.[8] It was used for 25 years, then laid up for parts, the remains sold for scrap in 1966. Storey was president of the railroad from 1920-1933.
A.G. Wells, built at Superior, Wisconsin as Hukey in 1919,[7] was purchased used by the Santa Fe in September 1925.[8] She was commandeered by the U.S. Government in 1943 and not returned.
After World War II
All three postwar tugs had steel hulls and entered service powered by a steam engine driving a single screw. In the mid-1960s the Hastings and Hayden were dieselized, but the Engel never was.[citation needed]
Edward J. Engel Santa Fe contracted with Consolidated Steel at Newport Beach, CA to construct a new "streamlined" tug. Launched in May 1945 Engle served till the late '60s.[8] Edward J. Engel, the namesake of the Engle, was the president of the railroad from 1939 to 1944.
During World War II the US Army had many tugboats built. As the war concluded Santa Fe acquired two of the LT (Large Tug) vessels for use in its cross-bay float service and another was built directly for them. All were named after prominent persons in the railroad:
Paul P. Hastings, named after the VP of Traffic for the railroad at the time of his retirement in 1941. Hastings was the brother of Milo Hastings and grandson of Pardee Butler.
John R. Hayden, named after the assistant to Mr. Engel.
Paul P. Hastings
The tugboat Paul P. Hastings in China Basin, San Francisco in 1982. At this time she was the last of the Santa Fe Railroad tugs still in service
On February 11, 1948, she was sold[11][incomplete short citation] to the Atchison, Topeka & Santa Fe Railroad Co. of San Francisco and renamed A.T.&S.F. No. 8, VIN D256253, Call Sign WD9219. She was later renamed the Paul P. Hastings, in honor of Paul P. Hastings, the vice-president of traffic for the railroad, who died in 1947.
The Paul P. Hastings had the longest period of service of the three post-war tugs: 36 years from 1948 until the railroad discontinued service in 1984. By the end she was the sole remnant of the tug fleet.
The Paul P. Hastings was sold and eventually became owned by Robert Whipple of American Navigation (AmNav[12][not specific enough to verify]), a company still doing business in the Bay area. The Abstract of Title shows Levin Metals Corp., a scrap dealer, as an intermediate owner starting at an unspecified date with Whipple taking title on February 26, 1991. The vessel was renamed Terminator. One source[13][unreliable source?] says the tug sat unused for years. In about 1991 Whipple, who had a reputation[14][unreliable source?] for added huge amounts of horsepower to old tugs, added two additional 3,600hp (2,700kW) diesel engines. The tug was not inspected by the United States Coast Guard after the engines were added.[15][incomplete short citation]
The first job for the upgraded tug was to assist the Dock Express 20, a multi-purpose vessel of Dutch registry owned by Dock-Express Shipping B.V,[16][not specific enough to verify] in laying a fiber cable off Point Arena, California. Point Arena is north of San Francisco about 100 miles (160km) and is the closest point on the west coast of the continental United States to Japan, hence is the landing point for many trans-Pacific cables.
The Terminator became a victim of a marine casualty: she sank. Details of the sinking are found in the US Coast Guard Marine Casualty investigation MC93011836 and Marine Violation investigation MV92003258.
Late in the day of Monday, January 27, 1992, the vessels were about 20 nautical miles (37km) off the coast of California just north of Point Arena at N39°9.0', W124°10.5'. The weather was ugly: swell height was 15 feet (4.6m) and increasing, wind speed was 35 knots (65km/h). Trouble started when a two-inch cable parted at the Sampson braid and the Terminator had to approach the Dock Express 20. It was now a little after 6 pm in deepening twilight (sunset was 5:31 pm).
Shortly after completing her approach to 100–150 feet (30–50m) abeam of the Dock Express 20, Terminator lost the use of the center engine. The operator attempted to use the port and starboard engines in a twisting fashion to maneuver the vessel out of danger. Then the starboard engine tripped off-line leaving the Terminator with only one of three engines operating. Attempts to restart the starboard engine failed. The high seas were abeam (perpendicular) to the vessel and pushed her into the protruding sponson (a structure on the side of the ship) of the Dock Express 20, who was restricted in her ability to maneuver as a result of her cable laying operation and because of its size was much less affected by the seas. When the vessels collided the Terminator was coming down off the crest of a swell, while the Dock Express 20 was surging upwards from another wave.
The impact created a hole, estimated at 1 to 2 feet (0.3 to 0.6m) in diameter, in the Terminator's aft lazarette area (a storage space between decks). The incoming water flooded the shaft alley. The watertight door between the shaft alley and main engine compartment was permanently affixed open. A cutting torch was needed before the door could be secured. This process took 20 minutes and only slowed the water coming into the engine room. Pumps to de-water the vessel operated only intermittently. There was no eductor (a type of water pump). The aft peak tank and bilge were filled with concrete (presumably for stability) and this extra weight could not be shifted to another area of the vessel from where the vessel was taking on water.
With the ship starting to sink the order to abandon ship was given about an hour after the collision. After 15 minutes only the bow was visible and after another 10 minutes, the vessel was completely underwater. All crew members entered the life raft and were picked up an hour later by the Craig Foss, a nearby tug which was diverted to assist. The Terminator sank in 800 fathoms (1,500m). About 35,000 US gallons (130,000L) of diesel fuel onboard spilled creating a light sheen in the vicinity which dissipated in a few days without cleanup. The vessel owner, Whipple, was fined $2,100 for the oil spill.
NOAA chart 18620 with the location of the Terminator sinking marked. The ocean is 800 fathoms (1,500m) deep where she rests 20 nautical miles (37km) offshore.
Edward J. Engel
The Edward J. Engel just after she was built in 1945 undergoing her sea trials. Note the fire monitor astern.
The Engel had a single screw and a steel hull of dimensions 141.5×29×12.7ft (43.1×8.8×3.9 m). She was powered by a three-cylinder Skinner Uniflow steam engine, 25 x 20, 1,200ihp (890kW)Babcock & Wilcox water tube boiler, with a 3,311sqft (307.6m2) heating surface, which provided 236psi (1.63MPa) working pressure.[9][unreliable source?] She retained this steam power plant at the time of her sinking in 2007.[2] Her sister tugs were built with steam and later dieselized. Her VIN number was 248085.[18]
On September 30, 1969 with barge traffic declining as piggy-back truck usage increased, the Santa Fe sold[11][incomplete short citation] the Engel to John K. Seaborn, a collector of old tugs and ferries. The sale was not recorded until June 25, 1971. On September 18, 1975 the vessel was removed from documentation because the name was changed to Respect without the consent of the Documentation Officer at the vessel’s home port who at that time had no record of the whereabouts of the vessel or owner.
The next entry in the Abstract of Title for the Engel is on February 24, 2006 when Seaborn sold the vessel to Sause Marine Services, Inc.[19][irrelevant citation] in the person of Gary Sause. Sause intended[20][unreliable source?] to dieselize the vessel whose hull was still in good condition. When Sause received an unsolicited bid for the vessel from Jeff Barnell he accepted it. What Barnell intended to do with the vessel is unknown. In any case he soon sold it to Ron Cook of British Columbia. The Engel/Respect had now changed hands three times in a little over a year. Cook planned to move the vessel to Seattle and restore it. There had been other attempts to restore and preserve the Engel. The Newport Harbor Nautical Museum,[21] near where the tug was built, was contacted but showed no interest. There are several references in Trainorders.COM[22][unreliable source?] in the fall of 2006 about saving the Engel.
For many years the Engel had been anchored in the Oakland estuary in Oakland, California just west of the Park Street bridge. The tug was vandalized on April 9, 2007 and sank the next day. She likely began taking on water following the removal of the brass seacock valve (used to cool the engine with seawater) for its scrap value. Following the sinking, she was under the administration of the U.S. Army Corps of Engineers.[23] As of February 2008 she remained submerged in the estuary, and her location was marked with buoys and a flashing light.[citation needed] On December 20, 2013, she was raised and removed from her sunken location where she impeded a navigable waterway.[24] Her last transit out the estuary was attached to the bow of the DB GENERAL pushed by the TUG FAT CAT. [citation needed] Following raising, the wreck needed to decontaminated, as she contained a large amount of asbestos and oil, as well as contaminated sediment. Following decontamination, the superstructure of the Engle/Respect was removed at Bay Ship and Yacht before the rest of the hull was scrapped at a U.S. Army Corps of Engineers dock in Sausalito in early 2014.[25]
The Edward J. Engel tugboat with carfloat #8 in the Oakland, California estuary
The John R. Hayden tugboat at the Todd shipyard in Alameda, California where she was dieselized. She was built in 1945 for the War Department as Large Tug LT-830. The tug is painted in "Warbonnet" colors which were similar to the Santa Fe diesel-electric locomotives of the time.
History
Name
LT 830
Builder
Tampa Marine Corp.
Christened
1945
Fate
Purchased by Santa Fe Railroad on June 5, 1947 and renamed John R Hayden
History
Name
John R Hayden
Owner
Atchison, Topeka and Santa Fe Railway
Fate
Sold September 16, 1976 and renamed Marine Crusader
History
Name
Marine Crusader
Owner
Marine Leasing Corp
Fate
Sold to Sause Bros Ocean Towing in 1990
History
Name
Titan
Owner
Sause Bros Ocean Towing
Fate
Put up for sale in 2016 Unknown - Listed for sale in 2016
1967: 1,600hp (1,200kW) General Motors 567C EMD F-7 diesel engine
1990: Two 12-cylinder turbo EMD engines
Propulsion
single screw
The John R. Hayden is the only tug of the Santa Fe post World War II tug fleet that remains afloat. She was built in 1945 by the U.S. War Department and is now the Titan owned by Sause Bros. and operating out of Coos Bay, Oregon. She had several other owners and names. She was repowered three times. The VI number (VIN) of the tug is 253495, IMO Number is 8424123.
The Hayden was built in 1945, the final year of World War II, by Tampa Marine Corp. in Tampa, Florida as hull number 40 and designated LT-830 (LT for Large Tug). Dimensions were 142.2ft (43.3m) × 33ft (10m) × 16ft (4.9m), tonnage 581 gt, 35 nt.[9][unreliable source?] She had a single screw.
On September 16, 1976, with barge traffic in decline, the Santa Fe sold the Hayden to Marine Leasing Corp. Marine Leasing repowered the tug, which required rebuilding the superstructure. On December 22, 1983, Marine Leasing renamed the vessel the Marine Crusader. Her home port was then Seattle, Washington.
The repowering of the Marine Crusader was done by Propulsion Systems Inc. of Kent, Washington. The repowered tug put to sea in December 1983 as one of the most highly computerized and automated tugs in the world. It also represented the most complete installation to date of a ship control and monitoring system. The new engines consisted of four General Motors Detroit Diesel 16-cylinder, 1600hp 149T1 diesel engines with a pair of twin-shaft input/single-shaft output Lufkin reduction gears with controllable-pitch propellers. The control system provided automatic engine load control, multiple engine load sharing, pitch control, machinery monitoring, and steering. The control complex involved two electrically isolated units, port and starboard. Machinery control function was divided between the units, each managing its own propulsion subsystem consisting of two engines, reduction gears with clutches and hydraulics for controllable-pitch propeller. There was an automatic pilot function driven by either gyrocompass or magnetic compass as the input heading source. There were four control station in the tug: main bridge, wing stations port and starboard, and an aft control station. All control systems operated off a non-interruptible power system.[27]
As rebuilt, the Marine Crusader had a beam of 33 feet (10m). A new epoxy coating was applied to the hull. She had quarters for an operating crew of eight. She had a gym in the forecastle, a useful accoutrement on long, ocean tow missions. With full tanks the Marine Crusader carried 225,000 gallons of fuel.[28]
On November 26, 1984 Marine Crusader was sold to Alaska Marine Towing Inc. On February 5, 1985 Marine Leasing changed her name to Harris Bay, after a bay in the Kenai peninsula south of Anchorage, Alaska. Alaska Marine ran into financial difficulties and filed for bankruptcy. As part of an August 3, 1988 reorganization the new legal owner of the Harris Bay became United Marine Tug and Barge. On August 29, 1988 they changed her name back to Marine Crusader.
Two years later on July 27, 1990 the tug was sold yet again to its current owner Sause Bros. Ocean Towing[29][irrelevant citation] of Portland, Oregon. Sause Bros. soon gave the tug her current name, Titan, and repowered her with two 12-cylinder turbo EMD engines, with 3½ to 1 Lufkin gears.
Sause has since removed the Titan from service and maintained her laid up in Coos Bay after removing the EMD engines they had installed previously rather than choosing to rebuild them. After determining it would not be cost-effective to repower a 70-year-old hull the decision was made to dispose of the Titan.[citation needed]
It is currently unknown if Titan still remains today, although it is very likely that it is still laid up somewhere in Oregon, despite the fact that it does not appear to be visible anywhere along recent Google Maps imagery in Coos Bay.[original research?]
The John R. Hayden tugboat when she was the Marine Crusader in 1983–1985 and again in 1988–1990
The John R. Hayden tugboat when she was the Harris Bay in the late 1980s at the Marine Power and Equipment docks in Seattle, Washington
The John R. Hayden tugboat, after several changes of owners and names and repowerings, is now owned by Sause Bros. and named Titan. She sails out of Coos Bay, Oregon
Related Research Articles
A tugboat or tug is a marine vessel that manoeuvres other vessels by pushing or pulling them, with direct contact or a tow line. These boats typically tug ships in circumstances where they cannot or should not move under their own power, such as in crowded harbors or narrow canals, or cannot move at all, such as barges, disabled ships, log rafts, or oil platforms. Some are ocean-going, and some are icebreakers or salvage tugs. Early models were powered by steam engines, which were later superseded by diesel engines. Many have deluge gun water jets, which help in firefighting, especially in harbours.
Union Iron Works, located in San Francisco, California, on the southeast waterfront, was a central business within the large industrial zone of Potrero Point, for four decades at the end of the nineteenth and beginning of the twentieth centuries.
A ferry slip is a specialized docking facility that receives a ferryboat or train ferry. A similar structure called a barge slip receives a barge or car float that is used to carry wheeled vehicles across a body of water.
Hercules is a 1907-built steam tugboat that is now preserved at the San Francisco Maritime National Historical Park in San Francisco, California.
San Francisco Bay in California has been served by ferries of all types for over 150 years. John Reed established a sailboat ferry service in 1826. Although the construction of the Golden Gate Bridge and the San Francisco–Oakland Bay Bridge led to the decline in the importance of most ferries, some are still in use today for both commuters and tourists.
USS Lanier (APA-125) was a Haskell-class attack transport in service with the United States Navy from 1944 to 1946. She was scrapped in 1973.
The South Pacific Coast Railroad (SPC) was a 3 ft narrow gauge steam railroad running between Santa Cruz, California, and Alameda, with a ferry connection in Alameda to San Francisco. The railroad was created as the Santa Clara Valley Railroad, founded by local strawberry growers as a way to get their crops to market in San Francisco and provide an alternative to the Southern Pacific Railroad. In 1876, James Graham Fair, a Comstock Lode silver baron, bought the line and extended it into the Santa Cruz Mountains to capture the significant lumber traffic coming out of the redwood forests. The narrow-gauge line was originally laid with 52-pound-per-yard (26 kg/m) rail on 8-foot (2.44 m) redwood ties; and was later acquired by the Southern Pacific and converted to 4 ft 8+1⁄2 instandard gauge.
USS Quapaw (ATF–110/AT-110) was a Abnaki-class fleet ocean tug in the United States Navy. She was named after the Quapaw.
The Mary D. Hume was a steamer built at Gold Beach, Oregon in 1881, by R. D. Hume, a pioneer and early businessman in that area. Gold Beach was then called Ellensburg. The Hume had a long career, first hauling goods between Oregon and San Francisco, then as a whaler in Alaska, as a service vessel in the Alaskan cannery trade, then as a tugboat. She was retired in 1977 and returned to Gold Beach. In 1985 she sank in the Rogue River and has remained there ever since as a derelict vessel on the shoreline. The Hume is listed on the National Register of Historic Places.
Paul Pardee Hastings was a prominent executive of the Atchison, Topeka, and Santa Fe Railroad.
Asbury Park was a high-speed coastal steamer built in Philadelphia, and intended to transport well-to-do persons from New York to summer homes on the New Jersey shore. This vessel was sold to West Coast interests in 1918, and later converted to an automobile ferry, serving on various routes San Francisco Bay, Puget Sound and British Columbia. This vessel was known by a number of other names, including City of Sacramento, Kahloke, Langdale Queen, and Lady Grace.
USS Nokomis (YT-142/YTB-142/YTM-142) was a Woban-class harbor tug built in Bremerton, Wash, and assigned to Pearl Harbor, Hawaii, in 1940. Nokomis was present during the Japanese attack on Pearl Harbor, 7 December 1941. She was the first vessel on scene at the USS Arizona, and was called off by the officers on deck because of the imminent explosion of the battery below deck. It then left and helped beach the USS Nevada, with Hoga (YT-146), and YT-153. The beaching of the Nevada saved Pearl Harbor's mouth from being blocked. After that the USS Nokomis fought fires and dewatered the battleship USS California, for 3 days. This effort made the California salvageable, to be recommissioned again later in the war. Nokomis was also the last vessel to move the surviving YC-699 barge prior to the Japanese attack on Pearl Harbor. Post-war she continued serving Pearl Harbor ships until she was decommissioned in May 1973, and eventually sold for "scrap" to Crowley, in San Francisco. She was renamed Sea Serpent and served many years in the San Francisco Bay as a tug and fire boat. In 1989, after the Loma Prieta earthquake in the SF Bay area, Nokomis and Hoga fought fires alongside each other again.
USS Wenonah (YT-148/YTB-148/YTM-148) was a Woban-class district harbor tug which served during World War II in California ports, and continued her service until she was struck by the Navy in 1974. On 17 August 2009, the Wenonah sank while berthed at Treasure Island, CA, and was raised by the floating crane Left Coast Lifter on 28 August 2009.
Foss Maritime, is an American tugging company. The company was founded in 1889 by Thea Foss (1857–1927) and her husband Andrew Foss. The company is now the largest tug and towing concern on the west coast of the United States.
Alameda was the first of three large-capacity ferries intended to transport passengers across San Francisco Bay. Southern Pacific Transportation Company and predecessor railroads had been operating ferries between San Francisco and Oakland, California since 1862. By the early 20th century, service had stabilized on three routes to the San Francisco Ferry Building from Oakland Pier, Alameda, and the San Antonio Creek estuary. Each route required two ferries shuttling back and forth to meet the departure schedule, with a third ferry in reserve when one boat needed maintenance or repair. Southern Pacific's engineering department designed Alameda for the heavily traveled Oakland Pier route as passenger counts rose during the period of prosperity preceding World War I. Alameda used side wheels for propulsion; but, instead of being powered by a single walking beam engine, wheels were powered independently by two engines for greater maneuverability. The twin stacks were distinctive among 20th century San Francisco Bay ferries.
The SS St. Marys Challenger is a freight-carrying vessel operating on the North American Great Lakes built in 1906. Originally an ore boat, she spent most of her career as a cement carrier when much larger ore boats became common. After a 107-year-long working career as a self-propelled boat, she was converted into a barge and paired with the tug Prentiss Brown as an articulated tug-barge. Before conversion, she was the oldest operating self-propelled lake freighter on the Great Lakes, as well as being one of the last freight-carrying vessels on the Great Lakes to be powered by steam engines.
The California Steam Navigation Company was formed in 1854 to consolidate competing steamship companies in the San Francisco Bay Area and on the Sacramento and San Joaquin Rivers. It was successful in this effort and established a profitable near-monopoly which it maintained by buying out or bankrupting new competitors. In response to the Fraser Canyon gold rush and economic growth in the Pacific Northwest, the company expanded to ocean routes from San Francisco north to British Columbia. Similarly, as California's economy grew, the company offered service from San Francisco south to San Pedro and San Diego. It exited these markets in 1867 when competition drove prices to unprofitable levels. While the California Steam Navigation Company was successful throughout its life in suppressing steamboat competition on its core Bay Area and river routes, it could not control the rise of railroads. These new competitors reduced the company's revenue and profit. Finally, in 1871, the company's assets were purchased by the California Pacific Railroad, and the corporation was dissolved.
Sause Bros., Inc., a pioneering Oregon ocean towing company founded in 1936, is a privately held, fourth-generation family company serving routes along the West Coast of the United States, Hawaii and other islands of the South Pacific, as well as Alaska. It maintains a sixty-vessel fleet of tugboats and barges, employing approximately 400 people at its facilities in Coos Bay, Portland, and Rainier, Oregon; in Long Beach, California; and in Honolulu and Kalaeloa, Hawaii.
Ocean Wave was a steamboat that was operated from 1891 to 1897 on the Columbia River, from 1897 to 1899 on Puget Sound and from 1899 to 1911 as a ferry on San Francisco Bay. Ocean Wave is perhaps best known for transporting summer vacationers from Portland, Oregon to seaside resorts near Ilwaco, Washington during its service on the Columbia River. This vessel is also known for being the first ferry placed in service by the Atchison, Topeka and Santa Fe Railway.
↑ Routing history from Evan Werkema, an active Trainorder.COM member
↑ Transit details from the caption to the March page of the 1991 McMillan Publications Santa Fe Railroad Calendar
↑ List of pre-war tugs from Valley Division Vignettes, Krieger and Icanberry, 1983
1 2 3 Santa Fe Valuation Records-Account 56, Floating Equipment, Live List, July 1, 1916 – December 31, 1927, Scholtz Collection, Temple Railroad & Heritage Museum
1 2 "Tugs", Shipbuilding History, retrieved 30 January 2017
1 2 3 Santa Fe Valuation Records-Account 56, Floating Equipment, Live List, Jan 1, 1928 to __, Scholtz Collection, Temple Railroad & Heritage Museum
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
