Swiss coordinate system

Last updated

The Swiss coordinate system (or Swiss grid) is a geographic coordinate system used in Switzerland and Liechtenstein for maps and surveying by the Swiss Federal Office of Topography (Swisstopo).

Contents

A first coordinate system was introduced in 1903 under the name LV03 (Landesvermessung 1903, German for “land survey 1903”), based on the Mercator projection and the Bessel ellipsoid. With the advent of GPS technology, a new coordinate system was introduced in 1995 under the name LV95 (Landesvermessung 1995, German for “land survey 1995”) after a 7-year measurement campaign.

LV is translated as MN in English. [1]

LV03

Introduced in 1903, this first geographic coordinate system rested upon the two dominant methodological pillars of geodesy and cartography at the time: the Bessel ellipsoid and the Mercator projection. Its measurements used the Bessel ellipsoid as an approximation of the Earth's shape, and its maps used the Mercator projection as a projection technique. Although not ideal, these approximations still offered a high level of precision in the case of Switzerland, due to the small size of its territory (41,285 km2 with max. 350km lengthways and 220km from North to South).

The fundamental reference point of the LV03 coordinate system was the old observatory of Bern, nowadays the location of the Institute of Exact Sciences of Bern University, in downtown Bern (Sidlerstrasse 5 - 46°57'3.9" N, 7°26'19.1" E). The coordinates of this reference point were arbitrarily fixed at 600'000 m E / 200'000 m N – with the East coordinate (E) noted before the North coordinate (N), unlike in the traditional latitude / longitude coordinate system. In selecting the values of these reference coordinates, the intention of the Swiss Federal Office of Topography was to guarantee that every point of the Swiss territory be identified by positive coordinates. The reference coordinates thus needed to be large enough to allow for positive coordinates to be allocated to the southernmost and westernmost areas of Switzerland. This goal was largely met by the 600'000 m E / 200'000 m N reference coordinates, as the corresponding origin point (0 m E / 0 m N) was located in Southwest France, near Bordeaux. In addition, the ratio between the East (E) and North (N) coordinates of the reference point was also set to be sufficiently high to guarantee that E coordinates be bigger than N coordinates over the entire Swiss territory.

Examples of LV03 coordinates

-       Rigi E=679520, N=212273

-       Zürich-Seebach E=684592, N=252857

LV95

With the advent of GPS technology, it became clear over the course of the 1980s that the LV03 coordinate system was no longer in a position to meet the rapidly growing precision standards set by new technologies. For instance, a difference of several meters was discovered when comparing the performance of LV03 and GPS technology in the measurement of the distance between the westernmost and easternmost areas of Switzerland (Geneva and Lower Engadin). As a result, the Swiss Federal Office of Topography decided to launch a new land survey campaign in 1988, with the intention of gathering precise data for the development of a new coordinate system based on WGS84. This survey ended in 1995, which is the reason why it was officially called LV95 (Landesvermessung 1995, German for “land survey 1995”).

The new coordinate system was designed with two main goals in mind: significantly increasing the precision of geographic coordinates, while at the same time preserving the conceptual foundations of the old LV03 for the sake of continuity. As such, the LV95 system continues to provide coordinates in the same order (East (E) before North (N)), and continues to allocate positive coordinates to every point of the Swiss territory.

In order to nonetheless achieve a clear distinction between the two systems, an additional digit was added to the coordinates of LV95: any East coordinate (E) now starts with a 2, and any North coordinate (N) with a 1. Consequently, LV95 coordinates are given by pairs of 7-digit numbers, whereas LV03 used pairs of 6-digit numbers – for instance the coordinates (2 600 000m E / 1 200 000m N) in LV95 would be expressed as (600 000m E / 200 000m N) in LV03. [2]

Another significant difference lies in the location of the fundamental reference point of the two systems. Under the LV95 system, coordinates are no longer calculated by referring to the old observatory of Bern (as was the case under the LV03 system), but instead to the Zimmerwald Observatory, located outside of Bern (approximately 10km to the South). Exact formulas used for the conversion of LV95 coordinates into latitude and longitude are provided by the Swiss Federal Office of Topography in its formal documentation of the LV95 system. [3]

Although the new geographic coordinate system LV95 was introduced in 1995, it was only progressively brought to use by Swiss authorities, with the official deadline for its definitive implementation having been fixed for the year 2016. Nowadays the LV95 system has become the main geographic reference frame of various institutions and governmental agencies, such as the Federal Statistical Office, the Swiss Army and the Swiss Border Guard, as well as cantonal police corps, emergency services and cadastre offices. Likewise, the official National Maps of Switzerland are now also founded upon this new coordinate system.

See also

Related Research Articles

<span class="mw-page-title-main">Geodesy</span> Science of measuring the shape, orientation, and gravity of the Earth and other astronomical bodies

Geodesy is the science of measuring and representing the geometry, gravity, and spatial orientation of the Earth in temporally varying 3D. It is called planetary geodesy when studying other astronomical bodies, such as planets or circumplanetary systems.

<span class="mw-page-title-main">Latitude</span> Geographic coordinate specifying north–south position

In geography, latitude is a coordinate that specifies the north–south position of a point on the surface of the Earth or another celestial body. Latitude is given as an angle that ranges from –90° at the south pole to 90° at the north pole, with 0° at the Equator. Lines of constant latitude, or parallels, run east–west as circles parallel to the equator. Latitude and longitude are used together as a coordinate pair to specify a location on the surface of the Earth.

<span class="mw-page-title-main">Projected coordinate system</span> Cartesian geographic coordinate system

A projected coordinate system – also called a projected coordinate reference system, planar coordinate system, or grid reference system – is a type of spatial reference system that represents locations on Earth using Cartesian coordinates (x, y) on a planar surface created by a particular map projection. Each projected coordinate system, such as "Universal Transverse Mercator WGS 84 Zone 26N," is defined by a choice of map projection (with specific parameters), a choice of geodetic datum to bind the coordinate system to real locations on the earth, an origin point, and a choice of unit of measure. Hundreds of projected coordinate systems have been specified for various purposes in various regions.

<span class="mw-page-title-main">Ordnance Survey National Grid</span> System of geographic grid references used in Great Britain

The Ordnance Survey National Grid reference system (OSGB) is a system of geographic grid references used in Great Britain, distinct from latitude and longitude.

<span class="mw-page-title-main">Transverse Mercator projection</span> Adaptation of the standard Mercator projection

The transverse Mercator map projection is an adaptation of the standard Mercator projection. The transverse version is widely used in national and international mapping systems around the world, including the Universal Transverse Mercator. When paired with a suitable geodetic datum, the transverse Mercator delivers high accuracy in zones less than a few degrees in east-west extent.

<span class="mw-page-title-main">Swisstopo</span> Swiss geological survey

Swisstopo is the official name for the Swiss Federal Office of Topography, Switzerland's national mapping agency.

<span class="mw-page-title-main">Geodetic datum</span> Reference frame for measuring location

A geodetic datum or geodetic system is a global datum reference or reference frame for precisely representing the position of locations on Earth or other planetary bodies by means of geodetic coordinates. Datums are crucial to any technology or technique based on spatial location, including geodesy, navigation, surveying, geographic information systems, remote sensing, and cartography. A horizontal datum is used to measure a location across the Earth's surface, in latitude and longitude or another coordinate system; a vertical datum is used to measure the elevation or depth relative to a standard origin, such as mean sea level (MSL). Since the rise of the global positioning system (GPS), the ellipsoid and datum WGS 84 it uses has supplanted most others in many applications. The WGS 84 is intended for global use, unlike most earlier datums.

<span class="mw-page-title-main">Universal Transverse Mercator coordinate system</span> Map projection system

The Universal Transverse Mercator (UTM) is a map projection system for assigning coordinates to locations on the surface of the Earth. Like the traditional method of latitude and longitude, it is a horizontal position representation, which means it ignores altitude and treats the earth surface as a perfect ellipsoid. However, it differs from global latitude/longitude in that it divides earth into 60 zones and projects each to the plane as a basis for its coordinates. Specifying a location means specifying the zone and the x, y coordinate in that plane. The projection from spheroid to a UTM zone is some parameterization of the transverse Mercator projection. The parameters vary by nation or region or mapping system.

<span class="mw-page-title-main">Lambert conformal conic projection</span> Conic conformal map projection

A Lambert conformal conic projection (LCC) is a conic map projection used for aeronautical charts, portions of the State Plane Coordinate System, and many national and regional mapping systems. It is one of seven projections introduced by Johann Heinrich Lambert in his 1772 publication Anmerkungen und Zusätze zur Entwerfung der Land- und Himmelscharten.

<span class="mw-page-title-main">Spatial reference system</span> System to specify locations on Earth

A spatial reference system (SRS) or coordinate reference system (CRS) is a framework used to precisely measure locations on the surface of Earth as coordinates. It is thus the application of the abstract mathematics of coordinate systems and analytic geometry to geographic space. A particular SRS specification comprises a choice of Earth ellipsoid, horizontal datum, map projection, origin point, and unit of measure. Thousands of coordinate systems have been specified for use around the world or in specific regions and for various purposes, necessitating transformations between different SRS.

<span class="mw-page-title-main">Cartography of Switzerland</span> Overview of the cartography of Switzerland

The cartography of Switzerland is the history of surveying and creation of maps of Switzerland. Switzerland has had its current boundaries since 1815, but maps of the Old Swiss Confederacy were drawn since the 16th century. The first topographical survey on a federal level began in 1809, resulting in the Topographic Map of Switzerland or Dufour Map. From 1869 to 1901, this map was replaced by the Topographic Atlas of Switzerland or Siegfried Map.

<span class="mw-page-title-main">National Maps of Switzerland</span> Series of official Swiss maps

The National Maps of Switzerland, also referred to as the Swisstopo maps, are a set of official map series designed, edited and distributed by Swisstopo, the Swiss Federal Office of Topography. Each map series is based on an oblique, conformal, cylindrical projection, with a Swiss Coordinate system. All maps are updated in a complete cycle of about six years.

<span class="mw-page-title-main">Irish Transverse Mercator</span> Geographic coordinate system for Ireland

Irish Transverse Mercator (ITM) is the geographic coordinate system for Ireland. It was implemented jointly by the Ordnance Survey Ireland (OSi) and the Ordnance Survey of Northern Ireland (OSNI) in 2001. The name is derived from the Transverse Mercator projection it uses and the fact that it is optimised for the island of Ireland.

<span class="mw-page-title-main">Israeli Transverse Mercator</span> Geographic coordinate system for Israel

Israeli Transverse Mercator (ITM), also known as the New Israel Grid is the new geographic coordinate system for Israel. The name is derived from the transverse Mercator projection it uses and the fact that it is optimized for Israel. ITM has replaced the old coordinate system Israeli Cassini Soldner (ICS), also known as the Old Israel Grid (OIG). It became the official grid for Israel in 1998.

<span class="mw-page-title-main">Helmert transformation</span> Transformation method within a three-dimensional space

The Helmert transformation is a geometric transformation method within a three-dimensional space. It is frequently used in geodesy to produce datum transformations between datums. The Helmert transformation is also called a seven-parameter transformation and is a similarity transformation.

The Bessel ellipsoid is an important reference ellipsoid of geodesy. It is currently used by several countries for their national geodetic surveys, but will be replaced in the next decades by modern ellipsoids of satellite geodesy.

<span class="mw-page-title-main">Earth ellipsoid</span> Geometric figure which approximates the Earths shape

An Earth ellipsoid or Earth spheroid is a mathematical figure approximating the Earth's form, used as a reference frame for computations in geodesy, astronomy, and the geosciences. Various different ellipsoids have been used as approximations.

<span class="mw-page-title-main">Geodetic coordinates</span> Geographic coordinate system

Geodetic coordinates are a type of curvilinear orthogonal coordinate system used in geodesy based on a reference ellipsoid. They include geodetic latitude (north/south) ϕ, longitude (east/west) λ, and ellipsoidal heighth. The triad is also known as Earth ellipsoidal coordinates.

<span class="mw-page-title-main">Hellenic Geodetic Reference System 1987</span>

The Hellenic Geodetic Reference System 1987 or HGRS87 is a geodetic system commonly used in Greece (SRID=2100). The system specifies a local geodetic datum and a projection system. In some documents it is called Greek Geodetic Reference System 1987 or GGRS87.

<span class="mw-page-title-main">Web Mercator projection</span> Mercator variant map projection

Web Mercator, Google Web Mercator, Spherical Mercator, WGS 84 Web Mercator or WGS 84/Pseudo-Mercator is a variant of the Mercator map projection and is the de facto standard for Web mapping applications. It rose to prominence when Google Maps adopted it in 2005. It is used by virtually all major online map providers, including Google Maps, CARTO, Mapbox, Bing Maps, OpenStreetMap, Mapquest, Esri, and many others. Its official EPSG identifier is EPSG:3857, although others have been used historically.

References

  1. ↑ "Swiss Map Raster 200". Swisstopo . Retrieved 2 October 2023.
  2. ↑ "National Survey LV95". www.swisstopo.admin.ch. Retrieved 2023-12-30.
  3. ↑ "Transformation and calculation services". www.swisstopo.admin.ch. Retrieved 2019-12-02.


This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.