Taxiing

Jet airliners taxiing

A privately owned Sea Vixen taxis back from an air show flight, with wings folding as it moves.

Taxiing (rarely spelled taxying) ^[1] is the movement of an aircraft on the ground, under its own power, in contrast to towing or pushback where the aircraft is moved by a tug. The aircraft usually moves on wheels, but the term also includes aircraft with skis or floats (for water-based travel).

An airplane uses taxiways to taxi from one place on an airport to another; for example, when moving from a hangar to the runway. The term "taxiing" is not used for the accelerating run along a runway prior to takeoff, or the decelerating run immediately after landing, which are called the takeoff roll and landing rollout, respectively.

Etymology

Main article: Taxi § Etymology

As early as 1909 aviation journalists envisioned aeroplanes to replace the taxicab in traffic-congested cities. ^[2]

Some aviators and some linguists report that around the year 1911 the slang word "taxi" was in use for an "airplane". They suggest that the way aircraft move under power before they take off or after they land reminded someone of the way taxicabs slowly drove around the block when looking for passengers. ^{[3] [4]}

Also by 1909, French aviation pioneers like Blériot, Farman and Voisin used the term "taxi" for a trainer aircraft, that was so constructed that a pupil would not accidentally get airborne.^{[ citation needed ]}

Usage of the word for an airplane quickly disappeared again, but the verb "to taxi" stuck, and words like the "taxiway" were derived from it.

Propulsion

The thrust to propel the aircraft forward comes from its propellers or jet engines. Reverse thrust for backing up can be generated by thrust reversers such as on the Boeing C-17 Globemaster III, or reversible pitch propellers such as on the Lockheed C-130 Hercules, a rare procedure known as powerback. Most aircraft, however, are not designed to back up on their own and must be pushed back either by hand or by using an aircraft tug.

At low power settings, combustion aircraft engines operate at lower efficiency than at cruise power settings. A typical A320 spends an average of 3.5 hours a day taxiing, using 600 liters (160 U.S. gal) of fuel. Hybrid electrically driven nose gear are under development to allow high use aircraft to shut down the engines during taxi operations. ^[5]

Control

Aircraft on the right hand side has the right-of-way during taxiing.

Steering is achieved by turning a nose wheel or tail wheel/rudder; the pilot controls the direction travelled with their feet. Larger jet aircraft have a tiller wheel on the left side of the cockpit that acts as a steering wheel allowing the nosewheel to be turned hydraulically. Braking is controlled by differential toe or heel brakes. Not all aircraft have steerable wheels, and in some cases steering is solely by means of differential braking (all Van's aircraft for instance) or solely by means of the rudder (including all floatplanes).

Hover taxi

A Eurocopter EC120B hover-taxis

Skid-equipped helicopters and other VTOL (Vertical Take-Off and Landing) aircraft conduct hover taxiing to move in ground effect in the same manner that wheel-equipped aircraft ground taxi. In general hover taxis are conducted at speeds up to 20 kn (37 km/h; 23 mph), or below translational lift. ^[6]

The Bell CH-135 Twin Huey is hover taxied in a manner typical for skid-equipped aircraft of that size:

This sequence is initiated from a stabilized 5 ft hover. Move the aircraft forward over the ground at a brisk walking pace. Maintain a constant height above ground, constant forward speed and ensure that the skids remain parallel to the direction of movement. Anticipate stopping so that large rearward cyclic applications are not required as this may result in the tail skids striking the ground. You are often required to taxi out of wind; be aware that when taxiing downwind in strong wind conditions there may be insufficient rearward cyclic to ensure adequate control and that the tail will be nearer the ground. Taxiing downwind is limited to 30 kts. ^[7]

Safety

When taxiing, aircraft travel slowly. This ensures that they can be stopped quickly and do not risk wheel damage on larger aircraft if they accidentally turn off the paved surface. Taxi speeds are typically 16 to 19 kn (30 to 35 km/h; 18 to 22 mph). ^[8]

Rotor downwash limits helicopter hover-taxiing near parked light aircraft. The use of engine thrust near terminals is restricted due to the possibility of structural damage or injury to personnel caused by jet blast. ^[9]

References

1. Dept, United States Air Force (1956). United States Air Force Dictionary. p. 515.
2. Flight, Volume 1, 1909-12-11, page 804.
3. "Why is taxiing (As done by airplanes, etc) called that?".
4. "Taxi | Etymology, origin and meaning of taxi by etymonline".
5. Majcher, Kristin (1 April 2011). "Torque Test: The German Aerospace Center unveils a silent, emissions-free electric nose wheel drive system for the Airbus A320". Aviation Week Network. Aviation Week. Archived from the original on 18 May 2017. Retrieved 2011-04-22. The new, electric nose wheel can power the A320 both forward and backward without requiring power from the aircraft's main engine. In addition to the energy savings, the electric nose wheel completely eliminates engine noise during taxi maneuvers.
6. Crane, Dale: Dictionary of Aeronautical Terms, third edition, page 263. Aviation Supplies & Academics, 1997. ISBN   1-56027-287-2
7. 10 Tactical Air Group: CFACM 40-35 CH-135 Standard Maneuver Guide, page 1-1, section 103 Taxiing (unclassified). Canadian Forces Air Command, 1984
8. "A Statistical Learning Approach to the Modeling of Aircraft Taxi-Time" (PDF). MIT Lincoln Laboratory. Federal Aviation Administration. 10 Aug 2010. p. 4. Archived (PDF) from the original on April 26, 2014.
9. "Engine Thrust Hazards in the Airport Environment". www.boeing.com.

External links

• Media related to Taxiways at Wikimedia Commonsaircraft
• Media related to Taxiing in aviation at Wikimedia Commons