Track (moving medium)

Last updated

A track is a path on a recording medium. There are some variations in nomenclature; for some media a track is a logical (content based) path and for others it is based on the geometry of the medium. The term is not used for punched cards.

Contents

Content-based tracks

The terms session, title or track may be used, depending on the medium.

LP

A track on a long playing record (LP) is a segment of the spiral groove recording a single movement, song or other work. Usually, unrecorded sections of the groove guide the tone arm between consecutive tracks. However occasionally - for example on some language learning records - the tracks are not connected, and the tone arm must be moved manually to the next track's lead-in groove.

Optical disks

A track, session or title on an audiovideo optical disk is a segment recording a single movement, song or other work.

Geometry-based tracks

On some devices a track is defined based on the geometry of the medium, typically running for the full length or circumference.

Linear

On magnetic cards, magnetic strips and tape, tracks normally [lower-alpha 1] run the full length of the medium. Some devices record multiple tracks in parallel either to improve speed or to provide separate channels for, e.g., stereophonic sound.

Punched tape

On Punched tape, also known as paper [lower-alpha 2] tape, a track runs the length of the tape and all tracks are recorded in parallel. References to the number of tracks sometimes use the word channel or level. Five level tape is used for Baudot, eight-level for ASCII and twelve level for carriage control tapes.

Magnetic tape reels and cartridges

On analog audio tape, a track runs the length of the tape and typically contains a single channel; stereophonic and quadraphonic recording use multiple tracks.

On digital tape, a track runs the length of the tape; typically all tracks are written and read in parallel.

Magnetic cards and strips

On magnetic cards [lower-alpha 3] and magnetic strips used as storage media, a track runs the length of the card or strip; typically multiple tracks are written and read in parallel and considered to be a single logical track.

The NCR CRAM, [1] RCA Model 3488 Random Access Computer Equipment [2] and RCA 70/568-11 Mass Storage Unit [3] used magnetic cards in a magazine (deck for CRAM).inch).

The IBM 2321 Data Cell [4] used magnetic strips in a cell and subcell. The tracks had variable length count key data (CKD) records.

Magnetic stripe cards

Magnetic stripe cards are commonly used as credit cards, identity cards, and transportation tickets. Standardized cards contain up to three parallel tracks. Unusually, two different recording densities are used (210 and 75 bits per

Helical scan

On some videotape and magnetic tape media, a read/write head moves across the width of the tape while the tape is moving, providing a diagonal Helical scan. An example is the IBM 3850 Mass Storage System (MSS).

Rotating

A track [lower-alpha 4] on a rotating magnetic disk or drum normally [lower-alpha 5] runs for the circumference of the medium. All tracks on a magnetic drum have the same capacity.

Early rotating drives recorded bits at a constant angular density and all tracks had the same data capacity. On all contemporary disk drives a track contains fixed length sectors. However, some older disks and drums recorded variable length records, and the DASD subsystems supported for general use by IBM's flagship operating systems simulate the Count Key Data (CKD) organization.

The first disk drive, the 1957 IBM 350 disk storage, had ten 100 character sectors per track; the tracks on contemporary disk drives are substantially larger.

In the early days of the industry sectors were referred to by several other names.

Drums

All tracks on a rotating drum have the same data capacity. Early drums were used for main memory, and tracks were divided into fixed length words, typically 36 bits [6] for use on binary computers and ten digits plus sign [7] for use on decimal computers. Drums used for auxiliary storage typically had fixed length sectors, but the IBM 7320 [8] on the IBM 7090 and 7094 had variable length records controlled by a format track and the IBM 2301, [9] 2303 [10] and 7320 [11] on the S/360 had variable length CKD records.

Disks

The first disk drive, the 1957 IBM 350 disk storage, had ten 100 character sectors per track and recorded at a constant angular density; the tracks on contemporary disk drives are substantially larger and are recorded at a constant linear density, so that outer tracks contain more data than inner tracks. Most of the industry designed disk drives with fixed length sectors, however the IBM 1301 and IBM 1302 on the 7000 series had variable length records controlled by format tracks and all DASD on S/360 had variable length CKD records. Although IBM supports FBA and SCSI disk drives on IBM Z, its flagship z/OS operating system only has limited support for SCSI drives and requires CKD drives for most functions.

Virtual Geometry

Starting with the 3350, IBM offered disc drives with new geometries that could present the appearance of older disk drives. At the present time almost all IBM mainframes use DASD subsystems that look like 3390 drives but use SCSI disks and SSDs to actually store the data.

Notes

  1. ↑ But see Helical scan.
  2. ↑ The term paper tape was often used to refer to perforated Mylar tape.
  3. ↑ Not to be confused with magnetic stripes on, e.g., credit cards.
  4. ↑ Sometimes called a band.
  5. ↑ The RCA Data Record File [5] (DRF) used a spiral track.

Related Research Articles

<span class="mw-page-title-main">Disk storage</span> General category of storage mechanisms

Disk storage is a general category of storage mechanisms where data is recorded by various electronic, magnetic, optical, or mechanical changes to a surface layer of one or more rotating disks. A disk drive is a device implementing such a storage mechanism. Notable types are the hard disk drive (HDD) containing a non-removable disk, the floppy disk drive (FDD) and its removable floppy disk, and various optical disc drives (ODD) and associated optical disc media.

<span class="mw-page-title-main">Floppy disk</span> Removable disk storage medium

A floppy disk or floppy diskette is a type of disk storage composed of a thin and flexible disk of a magnetic storage medium in a square or nearly square plastic enclosure lined with a fabric that removes dust particles from the spinning disk. Floppy disks store digital data which can be read and written when the disk is inserted into a floppy disk drive (FDD) connected to or inside a computer or other device.

<span class="mw-page-title-main">Hard disk drive</span> Electro-mechanical data storage device

A hard disk drive (HDD), hard disk, hard drive, or fixed disk, is an electro-mechanical data storage device that stores and retrieves digital data using magnetic storage with one or more rigid rapidly rotating platters coated with magnetic material. The platters are paired with magnetic heads, usually arranged on a moving actuator arm, which read and write data to the platter surfaces. Data is accessed in a random-access manner, meaning that individual blocks of data can be stored and retrieved in any order. HDDs are a type of non-volatile storage, retaining stored data when powered off. Modern HDDs are typically in the form of a small rectangular box.

<span class="mw-page-title-main">IBM System/360</span> IBM mainframe computer family (1964–1977)

The IBM System/360 (S/360) is a family of mainframe computer systems that was announced by IBM on April 7, 1964, and delivered between 1965 and 1978. It was the first family of computers designed to cover both commercial and scientific applications and a complete range of applications from small to large. The design distinguished between architecture and implementation, allowing IBM to release a suite of compatible designs at different prices. All but the only partially compatible Model 44 and the most expensive systems use microcode to implement the instruction set, featuring 8-bit byte addressing and binary, decimal and hexadecimal floating-point calculations.

A direct-access storage device (DASD) is a secondary storage device in which "each physical record has a discrete location and a unique address". The term was coined by IBM to describe devices that allowed random access to data, the main examples being drum memory and hard disk drives. Later, optical disc drives and flash memory units are also classified as DASD.

<span class="mw-page-title-main">UNIVAC</span> Series of mainframe computer models

UNIVAC was a line of electronic digital stored-program computers starting with the products of the Eckert–Mauchly Computer Corporation. Later the name was applied to a division of the Remington Rand company and successor organizations.

<span class="mw-page-title-main">Drum memory</span> Magnetic data storage device

Drum memory was a magnetic data storage device invented by Gustav Tauschek in 1932 in Austria. Drums were widely used in the 1950s and into the 1960s as computer memory.

IBM manufactured magnetic disk storage devices from 1956 to 2003, when it sold its hard disk drive business to Hitachi. Both the hard disk drive (HDD) and floppy disk drive (FDD) were invented by IBM and as such IBM's employees were responsible for many of the innovations in these products and their technologies. The basic mechanical arrangement of hard disk drives has not changed since the IBM 1301. Disk drive performance and characteristics are measured by the same standards now as they were in the 1950s. Few products in history have enjoyed such spectacular declines in cost and physical size along with equally dramatic improvements in capacity and performance.

<span class="mw-page-title-main">IBM 305 RAMAC</span> IBM computer released in 1956

The IBM 305 RAMAC was the first commercial computer that used a moving-head hard disk drive for secondary storage. The system was publicly announced on September 14, 1956, with test units already installed at the U.S. Navy and at private corporations. RAMAC stood for "Random Access Method of Accounting and Control", as its design was motivated by the need for real-time accounting in business.

<span class="mw-page-title-main">Magnetic storage</span> Recording of data on a magnetizable medium

Magnetic storage or magnetic recording is the storage of data on a magnetized medium. Magnetic storage uses different patterns of magnetisation in a magnetizable material to store data and is a form of non-volatile memory. The information is accessed using one or more read/write heads.

This article discusses support programs included in or available for OS/360 and successors. IBM categorizes some of these programs as utilities and others as service aids; the boundaries are not always consistent or obvious. Many, but not all, of these programs match the types in utility software.

Magnetic-tape data storage is a system for storing digital information on magnetic tape using digital recording.

<span class="mw-page-title-main">NCR Century 100</span> 1968 computer system

The NCR Century 100 was NCR's first all integrated circuit computer built in 1968. All logic gates were created by wire-wrapping NAND gates together to form flip-flops and other complex circuits. The console of the system had only 18 lights and switches and allowed entry of a boot routine, or changes to loaded programs or data in memory. A typewriter console was also available.

<span class="mw-page-title-main">Disk sector</span> Logical or physical division of storage media

In computer disk storage, a sector is a subdivision of a track on a magnetic disk or optical disc. For most disks, each sector stores a fixed amount of user-accessible data, traditionally 512 bytes for hard disk drives (HDDs) and 2048 bytes for CD-ROMs and DVD-ROMs. Newer HDDs use 4096-byte (4 KiB) sectors, which are known as the Advanced Format (AF).

Count key data (CKD) is a direct-access storage device (DASD) data recording format introduced in 1964, by IBM with its IBM System/360 and still being emulated on IBM mainframes. It is a self-defining format with each data record represented by a Count Area that identifies the record and provides the number of bytes in an optional Key Area and an optional Data Area. This is in contrast to devices using fixed sector size or a separate format track.

Fixed-block architecture (FBA) is an IBM term for the hard disk drive (HDD) layout in which each addressable block on the disk has the same size, utilizing 4 byte block numbers and a new set of command codes. FBA as a term was created and used by IBM for its 3310 and 3370 HDDs beginning in 1979 to distinguish such drives as IBM transitioned away from their variable record size format used on IBM's mainframe hard disk drives beginning in 1964 with its System/360.

<span class="mw-page-title-main">IBM 2321 Data Cell</span>

The IBM 2321 Data Cell is a discontinued direct access storage device (DASD) for the IBM System/360. It was announced with System/360 in April, 1964. It holds up to 400 megabytes of data, with an access time of 95 milliseconds to 600 milliseconds, depending on the addressed strip position and data arrangement in each data cell.

Beginning with its 1964 System/360 announcement, IBM's mainframes initially accessed CKD subsystems via a channel connected to separate Storage Control Units (SCUs) with attached Direct Access Storage Devices (DASD), typically a hard disk drive. This practice continued in IBM's larger mainframes thru System/370; however low end systems generally used lower cost integrated attachments where the function of the SCU was combined with that of the channel, typically called an Integrated File Adapter.

In addition to the drums used as main memory by IBM, e.g., IBM 305, IBM 650, IBM offered drum devices as secondary storage for the 700/7000 series and System/360 series of computers.

References

IBM2301
IBM System/360 Component Descriptions -- 2820 Storage Control and 2301 Drum Storage (PDF) (Third ed.), IBM, September 1968, A22-6895-2
IBM2841-0
IBM System/360 Component Descriptions 2841 Storage Control Unit 2302 Disk Storage Models 3 and 4 2311 Disk Storage Drive 2321 Data Cell Drive, Model 1 7320 Drum Storage (PDF), IBM, A26-5988-0
IBM2841-7
IBM System/360 Component Descriptions - 2841 and Associated DASD (PDF) (Eighth ed.), IBM, December 1969, GA26-5988-7
NCR315
Input, Output File Operations (PDF). The National 315 Electronic Data Processing System. NCR Corporation. 1961. F-7405. Retrieved January 3, 2023.
RCA3301
System Reference Manual (PDF). RCA 3301 Electronic Data Processing System. RCA. September 1967. 94-16-000. Retrieved January 3, 2023.
RCA 70/500
Random Access Device Series 70/500 (PDF). 70-06-500-1. RCA. November 1967. 70-06-500. Retrieved January 1, 2023.
  1. ↑ NCR315, pp.  7-12, Card Random Access Memory (CRAM).
  2. ↑ RCA3301, pp.  XVII-8-XVII-23, XVII Random Access Devices - Random Access Computer Equipment.
  3. ↑ RCA 70/500, pp.  69-80, Model 70/568-11 Mass Storage Unit.
  4. ↑ IBM2841-0, pp.  37-40, IBM 2321 Data Cell Drive.
  5. ↑ RCA 301 Electronic Data Processing System Programmers' Reference Manual (PDF), April 1960, p.  7, 93-16-000
  6. ↑ The UNIVAC Scientific General Purpose Computer System (Model 1103A) PRELIMINARY INFORMATION (PDF), Remington Rand, 1 December 1955
  7. ↑ "Storage" (PDF). IBM 650 magnetic drum data-processing machine manual of operation (PDF). 1955. p. 7. 22-6060-2.
  8. ↑ IBM 7090/7094 Data Processing Systems IBM 7320 Drum Storage (PDF), IBM, 1962, G22-6717
  9. ↑ IBM2301, pp.  30-31, IBM 2301 Drum Storage.
  10. ↑ IBM2841-7, pp.  73-76, IBM 2303 Drum Storage.
  11. ↑ IBM2841-0, pp.  41-42, IBM 7320 Drum Storage.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.