Twincharger

Last updated

A twincharger refers to a compound forced induction system used on some internal combustion engines. It is a combination of an exhaust-driven turbocharger and a mechanically driven supercharger, each mitigating the weaknesses of the other.

Contents

Twincharging does not refer to a twin-turbo arrangement, but to a setup where two different types of compressors are used (instead of only turbochargers or superchargers).

Overview and advantages

A mechanically driven supercharger offers exceptional response and low-rpm performance, as it does not rely on pressurization of the exhaust manifold (assuming that it is a positive-displacement design, such as a Roots-type or twin-screw, as opposed to a centrifugal supercharger, which does not provide substantial boost in the lower rpm range), but is less efficient than a turbocharger due to increased parasitic load. A turbocharger sized to move a large volume of air tends to respond slowly to throttle input, while a smaller, more responsive turbocharger may fail to deliver sufficient boost pressure through an engine's upper rpm range.

The unacceptable lag time endemic to a large turbocharger is effectively neutralized when combined with a supercharger, which tends to generate substantial boost pressure much faster in response to throttle input, the end result being a lag-free power band with high torque at lower engine speeds and increased power at the upper end. Twincharging is therefore desirable for small-displacement motors (such as VW's 1.4TSI), especially those with a large operating rpm range, since they can take advantage of an artificially broad torque band over a large speed range.

Types

A twincharging system combines a supercharger and turbocharger in a complementary arrangement, with the intent of one compressor's advantage compensating for the other's disadvantage. There are two common types of twincharger systems: series and parallel.

Series

The series arrangement, the more common arrangement of twinchargers, is set up such that one compressor's output feeds the inlet of another. A supercharger is connected to a medium- to large-sized turbocharger. The supercharger provides near-instant manifold pressure (eliminating turbo lag, which would otherwise result when the turbocharger is not up to its operating speed). Once the turbocharger has reached operating speed, the supercharger can either continue compounding the pressurized air to the turbocharger inlet (yielding elevated intake pressures), or it can be bypassed and/or mechanically decoupled from the drivetrain via an electromagnetic clutch and bypass valve, increasing induction efficiency.

Other series configurations exist where no bypass system is employed and both compressors are in continuous use. As a result, compounded boost is always produced as the pressure ratios of the two compressors are multiplied, not added. In other words, if a turbocharger which produces 10 psi (0.7 bar) on its own feeds into a supercharger which produces 10 psi on its own, the resultant manifold pressure would be 27 psi (1.9 bar) rather than 20 psi (1.4 bar). This form of series twincharging allows for the production of boost pressures that would otherwise be inefficient or unachievable with other compressor arrangements.

However, turbo and supercharger efficiencies do not multiply. For example, if a turbocharger with an efficiency of 70% feeds into a Roots supercharger with an efficiency of 60%, the total compression efficiency would be somewhere in between. To calculate this efficiency, it is necessary to calculate the efficiencies of the 2 stages, first calculating the conditions of pressure and temperature at the exit of the first stage and starting from these to calculate for the second stage. Following the previous example, for a first stage of the turbocharger with an efficiency of 70%, the temperature would reach 88.5 °C (191.3 °F) after the first stage, to then enter the supercharger with an efficiency of 60% and leave at a temperature of 186.5 °C (367.7 °F), resulting in a total efficiency of 62%. A large turbocharger that produces 27 psi (1.9 bar) by itself, with a thermal efficiency of around 70%, would produce air only 166 °C (331 °F) in temperature. In addition, the cost of energy to compress air with a supercharger is higher than that of a turbocharger; if the supercharger is not compressing air, there remains only a small parasitic loss of rotating the working parts of the supercharger. This remaining loss can be eliminated by disconnecting the supercharger further using an electromagnetic clutch (such as those used in the VW 1.4TSI or Toyota 4A-GZE to bypass the supercharger in low-load conditions).

With series twincharging, the turbocharger can be of a less expensive and more durable journal bearing variety, and the sacrifice in boost response is more than made up for by the instant-on nature of positive-displacement superchargers. While the weight and cost of the supercharger assembly are always a factor, the inefficiency of the supercharger is minimized once the turbocharger reaches operating speed and the supercharger is effectively disconnected by the bypass valve.

Parallel

Parallel arrangements typically require the use of a bypass or diverter valve to allow one or both compressors to feed the engine optimally. If no valve was used and both compressors were merely routed directly to the intake manifold, the supercharger would blow backwards through the turbocharger compressor rather than pressurize the intake manifold, as that would be the path of least resistance. Thus, a diverter valve must be employed to vent turbocharger air until the appropriate intake manifold pressure has been reached.

Disadvantages

The main disadvantage of twincharging is the complexity and expense of components. Usually, to provide acceptable response, smoothness of power delivery, and adequate power gain over a single-compressor system, expensive electronic and/or mechanical controls must be used. In a spark-ignition engine, a low compression ratio must also be used if the supercharger produces high boost levels, negating some of the efficiency benefits of a lower-displacement engine.

Applications

The concept of twincharging was first used by Lancia in 1985 in its Lancia Delta S4 Group B rally car and its street-legal counterpart, the Delta S4 Stradale. The idea was also successfully adapted to production road cars by Nissan with their March Super Turbo. [1] Additionally, multiple companies have produced aftermarket twincharger kits for cars like the Subaru Impreza WRX, Mini Cooper S, Ford Mustang, and Toyota MR2.

The Volkswagen 1.4 TSI is a 1400 cc engine – utilised by numerous automobiles of the VW Group – that sees use of both a turbocharger and a supercharger, and is available with eight power ratings:

PowerTorqueVehicles
103  kW (140  PS ; 138  bhp ) at 5,600 rpm220  N⋅m (162  lbf⋅ft ) at 1,500–4,000 rpm VW Golf V, VW Jetta V, and VW Touran
110 kW (150 PS; 148 bhp) at 5,800 rpm220 N⋅m (162 lbf⋅ft) at 1,250–4,500 rpm SEAT Ibiza IV
110 kW (150 PS; 148 bhp) at 5,800 rpm240 N⋅m (177 lbf⋅ft) at 1,500–4,000 rpm(CNG version) VW Passat VI, VW Passat VII, VW Touran
110 kW (150 PS; 148 bhp) at 5,800 rpm240 N⋅m (177 lbf⋅ft) at 1,750–4,000 rpm VW Sharan II, VW Tiguan, SEAT Alhambra
118 kW (160 PS; 158 bhp) at 5,800 rpm240 N⋅m (177 lbf⋅ft) at 1,500–4,500 rpm VW Eos, VW Golf VI, VW Jetta VI, VW Scirocco III
125 kW (170 PS; 168 bhp) at 6,000 rpm240 N⋅m (177 lbf⋅ft) at 1,500–4,500 rpm VW Golf V, VW Jetta V, VW Touran
132 kW (179 PS; 177 bhp) at 6,200 rpm250 N⋅m (184 lbf⋅ft) at 2,000–4,500 rpm VW Polo V, SEAT Ibiza Cupra, Škoda Fabia II
136 kW (185 PS; 182 bhp) at 6,200 rpm250 N⋅m (184 lbf⋅ft) at 2,000–4,500 rpm Audi A1

Volvo produces a twincharged 1969 cc inline-four engine that is utilised in their T6, T8, and Polestar models. The T8 adds onto the T6 with a rear electric motor.

PowerTorqueVehicles
320 PS (235 kW; 316 bhp) at 5,700 rpm400 N⋅m (295 lbf⋅ft) at 2,200–5,400 rpm Volvo S60 T6, Volvo V60 T6, Volvo S90 T6, Volvo XC60 T6, Volvo XC90 T6
367 PS (270 kW; 362 bhp) at 6,000 rpm470 N⋅m (347 lbf⋅ft) at 3,100–5,100 rpm Volvo S60 Polestar, Volvo V60 Polestar, Volvo XC60 Polestar
408 PS (300 kW; 402 bhp)640 N⋅m (472 lbf⋅ft) Volvo S60 T8, Volvo V60 T8, Volvo S90 T8, Volvo XC60 T8, Volvo XC90 T8 (with rear electric motor)

Jaguar Land Rover produces a twincharged 3.0L inline-six engine.

PowerTorqueVehicles
340 PS (250 kW; 335 bhp)495 N⋅m (354 lb⋅ft)P340
400 PS (294 kW; 395 bhp)550 N⋅m (406 lb⋅ft)P400

The Danish Zenvo ST1 supercar makes use of both turbocharging and supercharging in its 7.0-litre V8 engine.

PowerTorqueVehicles
1,104 hp (823 kW; 1,119 PS) at 6,900 rpm1,430 N⋅m (1,055 lbf⋅ft) at 4,500 rpmST1

Alternative systems

Anti-lag system

Anti-lag systems work in one of two ways: by running a very rich air–fuel ratio and pumping air into the exhaust to ignite unburnt fuel in the exhaust manifold, or by severely retarding ignition timing to cause combustion to continue well after the exhaust valve has opened. Both methods involve combustion in the exhaust manifold to keep the turbocharger spinning, and the heat from this will shorten the life of the turbine greatly. Therefore, in spite of twincharging's complexity, its largest benefit over anti-lag systems in race cars is reliability.

Variable geometry turbocharger

A variable-geometry turbocharger provides an improved response at varying engine speeds. With an electronically controlled variable angle of incidence, it is possible to have the turbine reach a good operating speed quickly or at lower engine speeds without severely diminishing its utility at higher engine speeds.

Twin-scroll turbocharger

A twin-scroll turbocharger design uses two separate chambers to better harness energy from alternating exhaust gas pulses. The chambers' nozzles may also be of different sizes, to better balance low-rpm response and high-rpm output.

Sequential twin turbochargers

Sequential turbocharger systems use differently-sized turbochargers to decrease turbo lag without compromising ultimate boost output and engine power.

Nitrous oxide

Nitrous oxide (N2O) is mixed with incoming air, serving as an oxidizing agent to burn more fuel for supplemental power when a turbocharger is not spinning quickly. This also produces more exhaust gases so that the turbocharger reaches operating speed faster, providing more oxygen for combustion, and the N2O flow is reduced accordingly. The expense of both the system itself and the consumable N2O can be significant.

Water injection

For increased engine power, and to augment other benefits of forced induction, an aftermarket water injection system can be added to the induction system of both gasoline and diesel internal combustion engines.

Related Research Articles

<span class="mw-page-title-main">Turbocharger</span> Exhaust-powered forced-induction device for engines

In an internal combustion engine, a turbocharger is a forced induction device that is powered by the flow of exhaust gases. It uses this energy to compress the intake air, forcing more air into the engine in order to produce more power for a given displacement.

<span class="mw-page-title-main">Miller cycle</span> Thermodynamic cycle

In engineering, the Miller cycle is a thermodynamic cycle used in a type of internal combustion engine. The Miller cycle was patented by Ralph Miller, an American engineer, U.S. patent 2,817,322 dated Dec 24, 1957. The engine may be two- or four-stroke and may be run on diesel fuel, gases, or dual fuel. It uses a supercharger or a turbocharger to offset the performance loss of the Atkinson cycle.

<span class="mw-page-title-main">Four-stroke engine</span> Internal combustion engine type

A four-strokeengine is an internal combustion (IC) engine in which the piston completes four separate strokes while turning the crankshaft. A stroke refers to the full travel of the piston along the cylinder, in either direction. The four separate strokes are termed:

  1. Intake: Also known as induction or suction. This stroke of the piston begins at top dead center (T.D.C.) and ends at bottom dead center (B.D.C.). In this stroke the intake valve must be in the open position while the piston pulls an air-fuel mixture into the cylinder by producing a partial vacuum in the cylinder through its downward motion.
  2. Compression: This stroke begins at B.D.C, or just at the end of the suction stroke, and ends at T.D.C. In this stroke the piston compresses the air-fuel mixture in preparation for ignition during the power stroke (below). Both the intake and exhaust valves are closed during this stage.
  3. Combustion: Also known as power or ignition. This is the start of the second revolution of the four stroke cycle. At this point the crankshaft has completed a full 360 degree revolution. While the piston is at T.D.C. the compressed air-fuel mixture is ignited by a spark plug or by heat generated by high compression, forcefully returning the piston to B.D.C. This stroke produces mechanical work from the engine to turn the crankshaft.
  4. Exhaust: Also known as outlet. During the exhaust stroke, the piston, once again, returns from B.D.C. to T.D.C. while the exhaust valve is open. This action expels the spent air-fuel mixture through the exhaust port.
<span class="mw-page-title-main">Napier Nomad</span> British diesel aircraft engine

The Napier Nomad is a British diesel aircraft engine designed and built by Napier & Son in 1949. They combined a piston engine with a turbine to recover energy from the exhaust and thereby improve fuel economy. Two versions were tested, the complex Nomad I which used two propellers, each driven by the mechanically independent stages, and the Nomad II, using the turbo-compound principle, coupled the two parts to drive a single propeller. The Nomad II had the lowest specific fuel consumption figures seen up to that time. Despite this the Nomad project was cancelled in 1955 having spent £5.1 million on development, as most interest had passed to turboprop designs.

<span class="mw-page-title-main">Roots blower</span> A positive displacement lobe pump

The Roots blower is a positive displacement lobe pump which operates by pumping a fluid with a pair of meshing lobes resembling a set of stretched gears. Fluid is trapped in pockets surrounding the lobes and carried from the intake side to the exhaust.

<span class="mw-page-title-main">Aircraft engine controls</span>

Aircraft engine controls provide a means for the pilot to control and monitor the operation of the aircraft's powerplant. This article describes controls used with a basic internal-combustion engine driving a propeller. Some optional or more advanced configurations are described at the end of the article. Jet turbine engines use different operating principles and have their own sets of controls and sensors.

Volumetric efficiency (VE) in internal combustion engine engineering is defined as the ratio of the equivalent volume of the fresh air drawn into the cylinder during the intake stroke to the volume of the cylinder itself. The term is also used in other engineering contexts, such as hydraulic pumps and electronic components.

<span class="mw-page-title-main">Naturally aspirated engine</span> Type of internal combustion engine

A naturally aspirated engine, also known as a normally aspirated engine, and abbreviated to N/A or NA, is an internal combustion engine in which air intake depends solely on atmospheric pressure and does not have forced induction through a turbocharger or a supercharger.

<span class="mw-page-title-main">Forced induction</span> Concept in engine design

In an internal combustion engine, forced induction is where turbocharging or supercharging is used to increase the density of the intake air. Engines without forced induction are classified as naturally aspirated.

The GM Ecotec engine, also known by its codename L850, is a family of all-aluminium inline-four engines, displacing between 1.4 and 2.5 litres. Confusingly, the Ecotec name was also applied to both the Buick V6 Engine when used in Holden Vehicles, as well as the final DOHC derivatives of the previous GM Family II engine; the architecture was substantially re-engineered for this new Ecotec application produced since 2000. This engine family replaced the GM Family II engine, the GM 122 engine, the Saab H engine, and the Quad 4 engine. It is manufactured in multiple locations, to include Spring Hill Manufacturing, in Spring Hill, Tennessee, with engine blocks and cylinder heads cast at Saginaw Metal Casting Operations in Saginaw, Michigan.

<span class="mw-page-title-main">Blowoff valve</span> A pressure release system in turbocharged engines

A blowoff valve is a pressure release system present in most petrol turbocharged engines. Blowoff valves are used to reduce pressure in the intake system as the throttle is closed, thus preventing compressor surge.

A wastegate is a valve that controls the flow of exhaust gases to the turbine wheel in a turbocharged engine system.

The anti-lag system (ALS) is a method of reducing turbo lag or effective compression used on turbocharged engines to minimize turbo lag on racing or performance cars. It works by delaying the ignition timing and adding extra fuel to balance an inherent loss in combustion efficiency with increased pressure at the charging side of the turbo. This is achieved as an excess amount of fuel/air mixture escapes through the exhaust valves and combusts in the hot exhaust manifold spooling the turbocharger creating higher usable pressure.

<span class="mw-page-title-main">Boost gauge</span> Type of pressure gauge

A boost gauge is a pressure gauge that indicates manifold air pressure or turbocharger or supercharger boost pressure in an internal combustion engine. They are commonly mounted on the dashboard, on the driver's side pillar, or in a radio slot.

In an internal combustion engine, twin-turbo is a layout in which two turbochargers work in tandem to compress the intake fuel/air mixture. The most common layout features two identical or mirrored turbochargers in parallel, each processing half of a V engine's produced exhaust through independent piping. The two turbochargers can either be matching or different sizes.

In turbocharged internal combustion engines, a boost controller is a device sometimes used to increase the boost pressure produced by the turbocharger. It achieves this by reducing the boost pressure seen by the wastegate.

<span class="mw-page-title-main">Nissan MA engine</span> Reciprocating internal combustion engine

The MA is a straight-4 SOHC 0.9 L, 1.0 L, or 1.2 L engine first introduced in 1982 by Nissan, intended primarily for the K10 series Micra/March model. It shares design similarities with the older E engine, with an 8-valve hemispherical cylinder head but differs in that it uses an aluminium cylinder block. Unusually, the specified ignition timing for the MA10 running on the specified 90 RON gasoline was 2 degrees after top dead centre, reflecting a very high flame speed in the compact combustion chambers.

<span class="mw-page-title-main">Supercharger</span> Air compressor for an internal combustion engine explaning

In an internal combustion engine, a supercharger compresses the intake gas, forcing more air into the engine in order to produce more power for a given displacement.

An electric supercharger is a specific type of supercharger for internal combustion engines that uses an electrically powered forced-air system that contains an electric motor to pressurize the intake air. By pressurizing the air available to the engine intake system, the air becomes more dense, and is matched with more fuel, producing the increased horsepower to the wheels.

<span class="mw-page-title-main">Internal combustion engine</span> Engine in which the combustion of a fuel occurs with an oxidizer in a combustion chamber

An internal combustion engine is a heat engine in which the combustion of a fuel occurs with an oxidizer in a combustion chamber that is an integral part of the working fluid flow circuit. In an internal combustion engine, the expansion of the high-temperature and high-pressure gases produced by combustion applies direct force to some component of the engine. The force is typically applied to pistons, turbine blades, a rotor, or a nozzle. This force moves the component over a distance, transforming chemical energy into kinetic energy which is used to propel, move or power whatever the engine is attached to.

References

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.