USS ABSD-3

Last updated
USS ABSD-3
ABSD3GuamMarianasIslandsUSSPennsylvaniaBB-38.jpg
ABSD-3 at Guam Apra Harbor repairing the USS Pennsylvania (BB-38) in September of 1945
History
Flag of the United States.svgUnited States
NameABSD-3 (AFDB-3)
Builder
Laid down1943-1943
Launched1943
AcquiredApril 1944
Commissioned27 October 1944
Out of service1948
ReclassifiedAFDB-3 (Large Auxiliary Floating Dry Dock)
Honours and
awards

American Campaign Medal ribbon.svg American Campaign Medal Asiatic-Pacific Campaign Medal ribbon.svg Asiatic-Pacific Campaign Medal World War II Victory Medal ribbon.svg World War II Victory Medal

Contents

General characteristics
TypeAdvance Base Sectional Drydock
Displacement30,800 long tons (31,294 t)
Length844 ft 3 in (257.33 m)
Beam246 ft 5 in (75.11 m)
Draft8 ft 8 in (2.64 m)
PropulsionNone
Complement22 officers and 471 enlisted men
Armament
  • 14 × 40 mm (1.6 in) guns
  • 14 × 20 mm (0.79 in) guns
USS ABSD-3 at Guam, empty ABSD-3atGuam.jpg
USS ABSD-3 at Guam, empty
USS AFDB-3 (ABSD-3) with rail traveling 15-ton crane, in Guam USSAFDB-3 USSABSD-3.jpg
USS AFDB-3 (ABSD-3) with rail traveling 15-ton crane, in Guam

ABSD-3 is an advanced base sectional dock, constructed of nine advance base dock (ABD) sections for the US Navy as an auxiliary floating drydock for World War II. ABSD-3 was delivered to the US Navy in April 1944, and was commissioned on 27 October 1944. Advance Base Sectional Dock-3 (Auxiliary Floating Dock Big-3) was constructed in sections during 1942 and 1943.

Each section was 3,850 tons and 80 feet long. Each section had a 256 feet beam, 75 feet molded depth and 10,000 tons lifting capacity. There were four ballast compartments in each section. With all nine sections joined, she was 844 feet long and 28 feet tall (keel to welldeck), with an inside clear width of 133 feet 7 inches. The length includes 3 feet between each section and 50 platforms at each end. There were 12 ballast tanks in each section. ABSD-2 had a traveling 15-ton capacity crane with an 85-foot radius and two or more support barges. The two side walls were folded down under tow to reduce wind resistance and lower the center of gravity. ABSD-3 had six capstans for pulling, each rated at 24,000 lbf (110,000 N) at 30 ft/min (0.15 m/s). Four of the capstans were reversible. [1] [2] [3] [4]

Construction

The nine sections that made up dock ABSD-3 were built at four different shipyards, to speed up construction:

[4]

World War II

Commissioned on 27 October 1944, the USS ABSD-3 was assigned to the Asiatic-Pacific Theater. It was towed in sections to the Naval Base Guam at Apra Harbor in Guam, Marianas Islands. After assembling she was placed in service to repair ships at Guam with ABSD-6.

On an island in the harbor at Guam the Navy built a base to support the crew of ABSD-3 and ABSD-6. At the base were supplies, movie theater, mess hall, officers' clubs, movie theater, and enlisted club. The base was built mostly with quonset huts.

The largest repairs at Guam were that of the USS Pennsylvania near the end of World War II; the ship was hit by a kamikaze attack off Okinawa on 12 August 1945. Due to the Pennsylvania's 28.9 ft (8.8 m) draft with a full load, the battleship had to unload much of her ammunition and fuel oil before entering AFDB-3. The USS Idaho (BB-42) was also repaired in ABSD-3 after a kamikaze attack on the same day.

Able to lift 90,000 tons, ABSD-3 could raise large ships such as aircraft carriers, battleships, cruisers, and large auxiliary ships, out of the water for repair below the waterline. She was also used to repair multiple smaller ships at the same time. Ships in continuous use during war need repair both from wear and from war damage from naval mine and torpedoes. Rudders and propellers are best serviced on dry docks. Without ABSD-2 and her sister ships, at remote locations months could be lost in a ships returning to a home port for repair. ABSD-3 had power stations, ballast pumps, repair shops, and machine shops, and could be self-sustaining. ABSD-2 had two rail track moveable cranes able to lift tons of material and parts, for removing damaged parts and installing new parts.

The first ship repaired at Guam was on 5 March 1945 and the last ship on 5 March 1946, after one year of operation. [5] [4]

Post-war

After the war ABSD-3 was decommissioned from the US Navy on 1 April 1946. Some sections were laid up in the Atlantic Reserve Fleet in Green Cove Springs, Florida. Some sections were stored in the James River Reserve Fleet from 1979 to 1982. [7]

She was struck from the Naval Register on 1 August 1981.

On 1 April 1982 eight sections were sold to Bath Iron Works in Bath, Maine. In 1982 she was towed to Portland, Maine. Bath Iron Works used the dock to lift new-built guided missile destroyers (DDG) to install sonar domes on the new ships' bows. The USS Samuel B. Roberts (FFG-58) was one of the ships serviced at the Bath Iron Works in May 1998. Bath Iron Works built a new land dry lock facility and no longer needed ABSD-3. [8]

In 1999 she was sold and then in 2000 moved to two pieces (four sections) with the heavy-lift ship MV Blue Marlin to a shipyard in Rijeka, Croatia. [9] [2] [4]

Related Research Articles

<span class="mw-page-title-main">Seeadler Harbor</span>

Seeadler Harbor, also known as Port Seeadler, is located on Manus Island, Admiralty Islands, Papua New Guinea and played an important role in World War II. In German, "Seeadler" means sea eagle, pointing to German colonial activity between 1884 and 1919 in that area. The bay was named in 1900 after the German cruiser SMS Seeadler.

<i>Los Alamos</i> (AFDB-7)

ABSD-7, an advanced base sectional dock, was constructed of seven advance base docks (ABD) as follows: ABD-37, ABD-38, ABD-39, and ABD-40 were built by Chicago Bridge & Iron Company, Morgan City, Louisiana, and completed in December 1944 and January and February 1945; ABD-51 and ABD-52 were built by Pollock-Stockton Shipbuilding Company, Stockton, California, and completed in January and March 1945; and ABD-58 was built by Pittsburgh-Des Moines Steel Co., Pittsburgh, Pennsylvania, and completed in October 1944.

USS <i>Artisan</i> US Navy floating drydock, 1943 to 1987

USS Artisan (ABSD-1), later redesignated as (AFDB-1), was a ten-section, non-self-propelled, large auxiliary floating drydock of the United States Navy. The only U.S. warship with this name, Artisan was constructed in sections during 1942 and 1943 by the Everett-Pacific Shipbuilding & Dry Dock Company, in Everett, Washington; the Chicago Bridge & Iron Company, in Eureka, California; the Pollock-Stockton Shipbuilding Company, in Stockton, California; and the Chicago Bridge & Iron Company, in Morgan City, Louisiana. This ship was commissioned at Everett, Washington, on 10 May 1943, Captain Andrew R. Mack in command. With all ten sections joined, she was 927 feet (283 m) long, 28 feet (8.5 m) tall, and with an inside clear width of 133 feet 7 inches (40.72 m).

USS LST-453 was a United States Navy LST-1-class tank landing ship used in the Asiatic-Pacific Theater during World War II. She was converted at Brisbane, Australia, into an Achelous-class repair ship, shortly after commissioning, and used in the repairing of landing craft. She was later renamed for Remus, she was the only US Naval vessel to bear the name.

USS <i>Sculptor</i> Cargo ship of the United States Navy

USS Sculptor (AK-103) was a Crater-class cargo ship commissioned by the US Navy for service in World War II. Sculptor was named after the constellation Sculptor. She was responsible for delivering troops, goods and equipment to locations in the Asiatic-Pacific Theater.

<span class="mw-page-title-main">Auxiliary floating drydock</span> Type of United States Navy drydocks

An auxiliary floating drydock is a type of US Navy auxiliary floating dry dock. Floating dry docks are able to submerge underwater and to be placed under a ship in need of repair below the water line. Water is then pumped out of the floating dry dock, raising the ship out of the water. The ship becomes blocked on the deck of the floating dry dock for repair. Most floating dry docks have no engine and are towed by tugboats to their destinations. Floating dry docks come in different sizes to accommodate varying ship sizes, while large floating dry docks come in sections and can be combined to increase their size and lift power. Ballast pontoon tanks are flooded with water to submerge or pumped dry to raise the ship.

USS <i>AFDM-2</i> Large auxiliary floating drydock of the US Navy

USS AFDM-2,, is an AFDM-3-class medium auxiliary floating drydock built in Mobile, Alabama by the Alabama Drydock and Shipbuilding Company for the U.S. Navy. Originally named USS YFD-4, Yard Floating Dock-4, she operated by Todd Shipyards at New Orleans, Louisiana for the repair of US ships during World War II. YFD-4 was renamed an Auxiliary Floating Dock Medium AFDM-2 in 1945 after the war.

USS <i>AFDB-2</i> Large auxiliary floating drydock of the US Navy

USS ABSD-2, later redesignated as AFDB-2, was a ten-section, non-self-propelled, large auxiliary floating drydock of the US Navy. Advance Base Sectional Dock-2 was constructed in sections during 1942 and 1943 by the Mare Island Naval Shipyard in Vallejo, California for World War II. Her official commissioning ceremony took place on 14 August 1943 with CDR Joseph J. Rochefort in command. With all ten sections joined, she was 927 feet (283 m) long, 28 feet (8.5 m) tall, and with an inside clear width of 133 feet 7 inches (40.72 m). ABSD-2 had a traveling 15-ton capacity crane with an 85-foot (26 m) radius and two or more support barges. The two side walls were folded down under tow to reduce wind resistance and lower the center of gravity. ABSD-2 had 6 capstans for pulling, each rated at 24,000 lbf (110,000 N) at 30 ft/min (0.15 m/s), 4 of the capstans were reversible. There were also 12 ballast compartments in each section.

USS <i>ABSD-6</i> WWII American floating drydock

ABSD-6 is an advanced base sectional dock which was constructed of nine advance base docks (ABD) sections for the US Navy as an auxiliary floating drydock for World War II. ABSD-6 was built by Mare Island Naval Shipyard at Vallejo, California. ABSD-6 was commissioned on 28 September 1944. Advance Base Sectional Dock-6 was constructed in sections during 1942 and 1943. Each section are 3,850 tons and are 93 feet long each. Each Section had a 165 feet beam, a 75 feet molded depth and had 10,000 tons lifting capacity each. There were 4 ballast compartments in each section. With all nine sections joined, she was 825 feet long, 28 feet tall, and with an inside clear width of 133 feet 7 inches. ABSD-2 had a traveling 15-ton capacity crane with an 85-foot radius and two or more support barges. The two side walls were folded down under tow to reduce wind resistance and lower the center of gravity. ABSD-6 had 6 capstans for pulling, each rated at 24,000 lbf (110,000 N) at 30 ft/min (0.15 m/s), 4 of the capstans were reversible.

USS <i>ABSD-4</i> Large auxiliary floating drydock of the US Navy

USS ABSD-4, later redesignated as AFDB-4, was a nine-section, non-self-propelled, large auxiliary floating drydock of the US Navy. Advance Base Sectional Dock-4 was constructed in sections during 1942 and 1943 by the Mare Island Naval Shipyard in Vallejo, California for World War II. With all ten sections joined, she was 927 feet long, 28 feet tall, and with an inside clear width of 133 feet 7 inches. ABSD-4 had a traveling 15-ton capacity crane with an 85-foot radius and two or more support barges. The two side walls were folded down under tow to reduce wind resistance and lower the center of gravity. ABSD-4 had 6 capstans for pulling, each rated at 24,000 lbf (110,000 N) at 30 ft/min (0.15 m/s), 4 of the capstans were reversible. There were also 4 ballast compartments in each section.

USS <i>ABSD-5</i> WWII American floating drydock

USS ABSD-5, later redesignated as AFDB-5, was a nine-section, non-self-propelled, large auxiliary floating drydock of the US Navy. Advance Base Sectional Dock-5 was constructed in sections during 1943 and 1944 by the Chicago Bridge & Iron Company in Morgan City, Louisiana for World War II. With all nine sections joined, she was 825 feet long, 28 feet tall, and with an inside clear width of 133 feet 7 inches. ABSD-5 had two traveling 15-ton capacity crane with an 85-foot radius and two or more support barges. The two side walls were folded down under tow to reduce wind resistance and lower the center of gravity. ABSD-5 had 6 capstans for pulling, each rated at 24,000 lbf (110,000 N) at 30 ft/min (0.15 m/s), 4 of the capstans were reversible. There were also 4 ballast compartments in each section.

Everett-Pacific Shipbuilding & Dry Dock Company was established in 1942 to build ships needed for World War II. Yard construction began on 1 March 1942. As part of the Emergency Shipbuilding Program, the US Navy provided some of the capital to start Everett-Pacific Shipbuilding at Port Gardner Bay in Everett, Washington. Everett-Pacific was sold in 1945 to the Pacific Car and Foundry, who was already a major manufacturer of railcars and trucks. Pacific Car and Foundry was building barges for the US Navy during World War II at plants in Renton, Seattle and Tacoma in the state of Washington. The lease for the shipyard in Everett, Washington ended in 1949 and the yard closed. Pacific Car and Foundry in 1972 changed its name to Paccar Inc. to reflect its major products. The Everett-Pacific shipyard site later became part of Western Gear, a heavy machinery manufacturer. From 1987 to 1992, the shipyard was rebuilt to become part of Naval Station Everett. Everett-Pacific Shipbuilding was started by William Pigott Jr. a Seattle businessmen and his brother Paul Pigott (1900-1961). William Pigott Jr. was born in 26 Aug. 1895 in Pueblo, CO and died on 8 July 1947 in San Francisco, CA.

Pollock-Stockton Shipbuilding Company was established in 1942 to build ships needed for World War II. As part of the Emergency Shipbuilding Program the US Navy provided some of the capital to start Pollock-Stockton Shipbuilding at Stockton, California. The shipyard was located at San Joaquin River and Stockton Channel, near Louis Park. After the war the shipyard closed down in February 1946.

<span class="mw-page-title-main">Naval Advance Base Espiritu Santo</span> Major World War 2 base

Naval Advance Base Espiritu Santo or Naval Base Espiritu Santo, most often just called Espiritu Santo, was a major advance Naval base that the U.S. Navy Seabees built during World War II to support the Allied effort in the Pacific. The base was located on the island of Espiritu Santo in the New Hebrides, now Vanuatu, in the South Pacific. The base also supported the U.S. Army and Army Air Corps, U.S. Coast Guard, and US Marine Corps. It was the first large advance base built in the Pacific. By the end of the war it had become the second-largest base in the theater. To keep ships tactically available there was a demand for bases that could repair and resupply the fleet at advance locations, rather than return them to the United States. Prior to December 7th, Pearl Harbor was the U.S. fleet's largest advance base in the Pacific. Espiritu became capable of all aspects necessary to support the Fleet's operations from fleet logistics in fuel, food, and ammunition, to transport embarkation for combat operations or returning to the continental United States. The ship repair facilities and drydocks were capable of attending to most damage and routine maintenance. Had it not existed, ships would have had to return to Pearl Harbor, Brisbane, or Sydney for major repairs and resupply. The base became a major R and R destination for the fleet.

<span class="mw-page-title-main">Bethlehem Sabine Shipyard</span> US Shipyard in Texas

Bethlehem Sabine Shipyard, or Sabine Shipyard was a 223-acre shipyard of Bethlehem Steel in Port Arthur, Texas. The Bethlehem Shipbuilding Corporation's Sabine Shipyard opened in August 1985. The yard serviced offshore drilling rigs and ships. The Sabine Shipyard had a nation's largest floating drydock. Bethlehem purchased the United States Navy surplus drydock, USS ABSD-5 that was at Pearl Harbor, Hawaii. USS ABSD-5 seven-sections were tugged to the Sabine Yard arriving in December 1984. USS ABSD-5 has a lift capacity of 64,000 tons.

<span class="mw-page-title-main">Naval Base Manus</span> Major US Navy Base on Manus Island, Papua New Guinea

Manus Naval Base was a number of bases built after the World War II Battle of Manus by United States Navy on the Manus Island and a smaller island just east, Los Negros Island in the Admiralty Islands chain. The major naval base construction started with the Los Negros landings on February 28, 1944. The Navy repaired and did the expansion of the airfields on the Admiralty Islands. United States Navy Seabee built or repaired the facilities on the islands. The large Manus Naval Base, also called the Admiralty Island base, supported United States Seventh Fleet, Southwest Pacific command, and part of the Pacific Fleet. The base was abandoned by the US Navy after the war.

References

  1. The Pacific War Online Encyclopedia, Floating Dry Docks
  2. 1 2 Building the Navy's Bases in World War II, History of the Bureau of Yards and Docks and the Civil Engineer Corps 1940-1946 Chapter IX, Floating Drydocks
  3. Angas, W. Mack, Capt. (CEC) USN (November 1945). "Sea Going Navy Yard Follows The Fleet". Popular Science : 121–124. Retrieved 2012-07-10.{{cite journal}}: CS1 maint: multiple names: authors list (link)
  4. 1 2 3 4 navsource.org, ABSD-3
  5. UN Navy Bureau of Ships Journal, Volume 1, page 7 May 1952
  6. ABSD-3 Repair records
  7. marad, Sections B
  8. Photos of USS Samuel B. Roberts on blocks in AFDB-3 in 1988
  9. "Floating Dry-Docks (AFDB, AFDM, AFDL, ARD, ARDM, YFD)". shipbuildinghistory.com. 30 April 2015. Retrieved 8 January 2019.