Variable displacement

Last updated

Variable displacement is an automobile engine technology that allows the engine displacement to change, usually by deactivating cylinders, for improved fuel economy. The technology is primarily used in large, multi-cylinder engines. Many automobile manufacturers have adopted this technology as of 2005, although the concept has existed for some time prior to this.

Contents

Theory of operation

Cylinder deactivation is used to reduce the fuel consumption and emissions of an internal combustion engine during light-load operation. In typical light-load driving the driver uses only around 30 percent of an engine’s maximum power. In these conditions, the throttle valve is nearly closed, and the engine needs to work to draw air. This causes an inefficiency known as pumping loss. Some large capacity engines need to be throttled so much at light load that the cylinder pressure at top dead centre is approximately half that of a small 4-cylinder engine. Low cylinder pressure results in lower fuel efficiency. The use of cylinder deactivation at light load means there are fewer cylinders drawing air from the intake manifold, which works to increase its fluid (air) pressure. Operation without variable displacement is wasteful because fuel is continuously pumped into each cylinder and combusted even though maximum performance is not required. By shutting down half of an engine's cylinders, the amount of fuel being consumed is much less. Between reducing the pumping losses, which increases pressure in each operating cylinder, and decreasing the amount of fuel being pumped into the cylinders, fuel consumption can be reduced by 8 to 25 percent in highway conditions. [1] [2]

Cylinder deactivation is achieved by keeping the intake and exhaust valves closed for a particular cylinder. By keeping the intake and exhaust valves closed, it creates an "air spring" in the combustion chamber – the trapped exhaust gases (kept from the previous charge burn) are compressed during the piston’s upstroke and push down on the piston during its downstroke. The compression and decompression of the trapped exhaust gases have an equalising effect – overall, there is virtually no extra load on the engine. In the latest breed of cylinder deactivation systems, the engine management system is also used to cut fuel delivery to the disabled cylinders. The transition between normal engine operation and cylinder deactivation is also smoothed, using changes in ignition timing, cam timing and throttle position (thanks to electronic throttle control). In most instances, cylinder deactivation is applied to relatively large displacement engines that are particularly inefficient at light load. In the case of a V12, up to 6 cylinders can be disabled. [1]

Two issues to overcome with all variable-displacement engines are unbalanced cooling and vibration.[ citation needed ]

History

The oldest engine technological predecessor for the variable-displacement engine is the hit and miss engine, developed in the late 19th century. These single-cylinder stationary engines had a centrifugal governor that cut the cylinder out of operation so long as the engine was operating above a set speed, typically by holding the exhaust valve open.

Cadillac L62 V8-6-4

Cadillac V8-6-4 emblem 81 Cadillac Sedan de Ville V864 (13923375327).jpg
Cadillac V8-6-4 emblem

First experiments with multiple-cylinder engines during WWII, [3] were re-attempted in 1981 on Cadillac's ill-fated L62 "V8-6-4" engine. The technology was made a standard feature on all Cadillac models except Seville, which had the 350 diesel V-8 engine as a base engine. Cadillac, in conjunction with Eaton Corporation, developed the innovative V-8-6-4 system which used the industry's first engine control unit to switch the engine from 8- to 6- to 4-cylinder operation depending on the amount of power needed. [3] The original multi-displacement system turned off opposite pairs of cylinders, allowing the engine to have three different configurations and displacements. The cars had an elaborate diagnostics procedure, including showing engine trouble codes on the air conditioning display. However, the system was troublesome, misunderstood by customers, and a rash of unpredictable failures led to the technology being quickly retired. [3]

Alfa Romeo Alfetta CEM

In 1981 Alfa Romeo developed in collaboration with the University of Genoa a semi-experimental variable displacement engine version of the Alfa Romeo Alfetta, called Alfetta CEM (Controllo Elettronico del Motore, or Electronic Engine Management), and showed it at the Frankfurt Motor Show. [4] The 130 PS (96 kW; 128 bhp) 2.0-litre modular engine featured fuel injection and ignition systems governed by an engine control unit, which could shut off two of four cylinders as needed in order to reduce fuel consumption. An initial batch of 10 examples were assigned to taxi drivers in Milan, to verify operation and performance in real-world situations. [4] [5] According to Alfa Romeo during these tests cylinder deactivation was found to reduce fuel consumption by 12% in comparison to a CEM fuel-injected engine without variable displacement, and almost by 25% in comparison to the regular production carburetted 2.0-litre. [5] After the first trial, in 1983 a small series of 1000 examples was put on sale, offered to selected clients; [4] 991 examples were produced. Despite this second experimental phase, the project had no further developments.

Mitsubishi MD

In 1982 Mitsubishi developed its own variable displacement in the form of MD (Modulated Displacement) which proved that the technology, first used in Mitsubishi's 1.4 L 4G12 straight-four engine, can function successfully. [6] Because Cadillac's system proved to be a failure and a four-cylinder engine was used, Mitsubishi hailed their own as a world first. [7] The technology was later used in Mitsubishi's V6 engines. [8]

The system worked by disabling the valves on cylinders number 1 and 4 at speeds below 70 km/h (43.5 mph), at idling, and while decelerating. Fuel consumption figures were generally about 20 percent improved over the regular 4G12 engine. [9] Period sources, however, complained about the engine running very roughly while in two-cylinder mode, despite special engine mounts with hydraulic damping. [10] Other efforts taken to minimize vibrations and harshness included a section of flexible exhaust pipe, not operating the system until the coolant temperature reached 70C, and a 70 percent heavier flywheel. [11] Mitsubishi's effort remained short-lived, mainly because of a lack of response from car buyers. [12]

In 1993, a year after Mitsubishi developed its own variable valve timing technology, the MIVEC-MD variant was introduced. The revived MD technology was now in its second generation with improved electronic engine controls enabling the switch from 4 to 2 cylinders to be made almost imperceptibly. In MD mode, the MIVEC engine utilizes only two of its four cylinders, which reduces significantly the energy wasted due to pumping losses. In addition, power loss due to engine friction is also reduced. [7] Depending on conditions, the MIVEC-MD system can reduce fuel consumption by 10–20 percent; although some of this gain is from the variable valve timing system, not from the variable-displacement feature. [8] Modulated Displacement was dropped around 1996. [8]

Aftermarket systems

A number of companies have developed aftermarket cylinder deactivation systems, with varying degrees of success. The 1979 EPA evaluation of the Automotive Cylinder Deactivation System (ACDS), which allowed eight-cylinder engines to be run on four cylinders, found that carbon monoxide and nitrogen oxide emissions were increased beyond the legal limits of the emission standards then in force. [13] While fuel economy was increased, acceleration was seriously compromised, and the loss of engine vacuum led to a dangerous loss of braking assist when the system was in four-cylinder mode. [13] In addition to these issues, while the company proposed a hydraulically controlled system that could be switched from within the car, the version they implemented had to be manually changed in the engine compartment using hand tools. [13]

Present

There are currently two main types of cylinder deactivation mechanizations used today, depending on the type of the engine's valvetrain. The first is for pushrod designs which uses solenoids to alter oil pressure delivered to lock pins in the lifters. With lock pin out of place, the lifters are collapsed and unable to elevate their companion pushrods under the valve rocker arms, resulting in valves that remain closed when the cam pushes on the part in lost motion.

The second type is for overhead cam engines, and uses a pair of locked-together rocker arms that are employed for each valve. One rocker follows the cam profile, while the other actuates the valve. When a cylinder is deactivated, solenoid-controlled oil pressure releases a locking pin between the two rocker arms. While one arm still follows the camshaft, the unlocked arm remains motionless and doesn't move the valve. [14] With computer control, fast cylinder deactivation and reactivation occur almost instantly. [15]

Several automotive manufacturers have engines with cylinder deactivation in current production.

Daimler AG's Active Cylinder Control (ACC) variable displacement technology debuted in 2001 on the 5.8 L V12 in the CL600 and S600.

Mercedes-Benz developed their Multi-Displacement System V12 in the late 1990s, which shuts off every other cylinder in the firing order. It was widely deployed on pushrod V8 engines starting with the 2004 DaimlerChrysler Hemi.

Starting in 2003, Honda introduced Variable Cylinder Management on the J family engines. Honda's system works by deactivating banks of cylinders, switching from 6 to 4 to 3 cylinders.

In 2005, GM introduced their Active Fuel Management cylinder deactivation system (in the Generation IV small-block) which, similar to Chrysler's MDS, switched off half of the cylinders. In 2018 GM introduced an improved system called Dynamic Fuel Management [16] that shuts off any number of cylinders, in a variety of combinations, depending on immediate needs. The system is based on Dynamic Skip Fire, [17] a technology developed by California company Tula Technology [18] and the 6.2L engine incorporating it was named one of Ward's 10 Best Engines for 2019.

In 2012 Volkswagen introduced Active Cylinder Technology (ACT), the first manufacturer to do so in four-cylinder engines. [19]

In November 2016 Ford announced its compact three-cylinder Ecoboost engine with deactivation on one of the cylinders. This is the smallest engine so far to use deactivation, and will allow the benefits to be applied in small cars. [20]

In November 2017, Mazda announced standard cylinder deactivation in all 2018 CX-5 models, and availability on Mazda6 models. [21] [22]

As of the 2020 model year, about 15% of light-duty vehicles sold in the United States used cylinder deactivation, predominantly used by Mazda (64%), GM (44%), Honda (24%), and FCA (23%). [23]

Variable compression ratio. The best known such system was the experimental Saab Variable Compression engine, which used a hinged block to move the pistons closer to or further from the head, thus changing the size of the combustion chambers. Other experimental systems include the Hefley engine, which uses a sliding crank race on an eccentric shaft, [24] and the Scalzo Piston Deactivation Engine, which uses a four-bar linkage, and has the distinction of being able to stop individual pistons entirely. [25] There are currently no production vehicles that use any of these designs.

Additionally, Cadillac's Northstar engine series featured a "limp home" fail-safe mode. If the engine lost coolant, the engine controller would cut fuel and spark to half of the cylinders. With valve operation left unaltered, the noncombustive cylinders would air-cool the engine, allowing it to drive up to 100 miles without coolant.

Variable-displacement technologies

See also

Related Research Articles

<span class="mw-page-title-main">Exhaust gas recirculation</span> NOx reduction technique used in gasoline and diesel engines

In internal combustion engines, exhaust gas recirculation (EGR) is a nitrogen oxide (NOx) emissions reduction technique used in petrol/gasoline, diesel engines and some hydrogen engines. EGR works by recirculating a portion of an engine's exhaust gas back to the engine cylinders. The exhaust gas displaces atmospheric air and reduces O2 in the combustion chamber. Reducing the amount of oxygen reduces the amount of fuel that can burn in the cylinder thereby reducing peak in-cylinder temperatures. The actual amount of recirculated exhaust gas varies with the engine operating parameters.

<span class="mw-page-title-main">Variable-length intake manifold</span>

In internal combustion engines, a variable-length intake manifold (VLIM),variable intake manifold (VIM), or variable intake system (VIS) is an automobile internal combustion engine manifold technology. As the name implies, VLIM/VIM/VIS can vary the length of the intake tract in order to optimise power and torque across the range of engine speed operation, as well as to help provide better fuel efficiency. This effect is often achieved by having two separate intake ports, each controlled by a valve, that open two different manifolds – one with a short path that operates at full engine load, and another with a significantly longer path that operates at lower load. The first patent issued for a variable length intake manifold was published in 1958, US Patent US2835235 by Daimler Benz AG.

<span class="mw-page-title-main">Variable valve timing</span> Process of altering the timing of a valve lift event

Variable valve timing (VVT) is the process of altering the timing of a valve lift event in an internal combustion engine, and is often used to improve performance, fuel economy or emissions. It is increasingly being used in combination with variable valve lift systems. There are many ways in which this can be achieved, ranging from mechanical devices to electro-hydraulic and camless systems. Increasingly strict emissions regulations are causing many automotive manufacturers to use VVT systems.

<span class="mw-page-title-main">MIVEC</span> Automobile variable valve timing technology

MIVEC (Mitsubishi Innovative Valve timing Electronic Control system) is the brand name of a variable valve timing (VVT) engine technology developed by Mitsubishi Motors. MIVEC, as with other similar systems, varies the timing of the intake and exhaust camshafts which increases the power and torque output over a broad engine speed range while also being able to help spool a turbocharger more quickly and accurately.

The GM Ecotec engine, also known by its codename L850, is a family of all-aluminium inline-four engines, displacing between 1.4 and 2.5 litres. Confusingly, the Ecotec name was also applied to both the Buick V6 Engine when used in Holden Vehicles, as well as the final DOHC derivatives of the previous GM Family II engine; the architecture was substantially re-engineered for this new Ecotec application produced since 2000. This engine family replaced the GM Family II engine, the GM 122 engine, the Saab H engine, and the Quad 4 engine. It is manufactured in multiple locations, to include Spring Hill Manufacturing, in Spring Hill, Tennessee, with engine blocks and cylinder heads cast at Saginaw Metal Casting Operations in Saginaw, Michigan.

Active Fuel Management is a trademarked name for the automobile variable displacement technology from General Motors. It allows a V6 or V8 engine to "turn off" half of the cylinders under light-load conditions to improve fuel economy. Estimated performance on EPA tests shows a 5.5–7.5% improvement in fuel economy.

<span class="mw-page-title-main">Mitsubishi 6A1 engine</span> Reciprocating internal combustion engine

The Mitsubishi 6A1 engine is a series of piston V6 engines from Mitsubishi Motors, found in their small and medium vehicles through the 1990s. They ranged from 1.6 to 2.5 L in size, and came with a variety of induction methods and cylinder head designs and configurations.

<span class="mw-page-title-main">Inlet manifold</span> Automotive technology

An inlet manifold or intake manifold is the part of an internal combustion engine that supplies the fuel/air mixture to the cylinders. The word manifold comes from the Old English word manigfeald and refers to the multiplying of one (pipe) into many.

<span class="mw-page-title-main">Mitsubishi Sirius engine</span> Reciprocating internal combustion engine

The Mitsubishi Sirius or 4G6/4D6 engine is the name of one of Mitsubishi Motors' four series of inline-four automobile engines, along with Astron, Orion, and Saturn.

<span class="mw-page-title-main">Mitsubishi 4G9 engine</span> Reciprocating internal combustion engine

The Mitsubishi 4G9 engine is a series of straight-4 automobile engines produced by Mitsubishi Motors. All are 16-valve, and use both single- and double- overhead camshaft heads. Some feature MIVEC variable valve timing, and it was the first modern gasoline direct injection engine upon its introduction in August 1996.

<span class="mw-page-title-main">Mitsubishi 6G7 engine</span> Reciprocating internal combustion engine

The 6G7 series or Cyclone V6 engine is a series of V6 piston engines from Mitsubishi Motors. Five displacement variants were produced from 1986 to 2021, with both SOHC and DOHC, naturally aspirated and turbo charged layouts. While MIVEC variable valve timing has also been implemented in some versions the 2.5, 3.0, and 3.5 L versions were also available with gasoline direct injection. This engine has been the flagship powerplant of the company except when they briefly built a V8 in 1999–2001. The staple of their high-end sedans, it was given twin-turbos for the Mitsubishi GTO, and became the most powerful car ever built by the company at the time.

Variable Cylinder Management (VCM) is Honda's term for its variable displacement technology, which saves fuel by using the i-VTEC system to disable one bank of cylinders during specific driving conditions—for example, highway driving. The second version of VCM (VCM-2) took this a step further, allowing the engine to go from 6 cylinders, down to 4, and further down to 3 as the computer sees fit. The most recent version of VCM (VCM-3) reverted to the previous 3- and 6-cylinder operation.

<span class="mw-page-title-main">Gasoline direct injection</span> Mixture formation system

Gasoline direct injection (GDI), also known as petrol direct injection (PDI), is a mixture formation system for internal combustion engines that run on gasoline (petrol), where fuel is injected into the combustion chamber. This is distinct from manifold injection systems, which inject fuel into the intake manifold.

Manifold vacuum, or engine vacuum in an internal combustion engine is the difference in air pressure between the engine's intake manifold and Earth's atmosphere.

Daimler AG's Active Cylinder Control (ACC) is a variable displacement technology. It debuted in 2001 on the 5.8 L V12 in the CL600 and S600. Like Chrysler's later Multi-Displacement System, General Motors' Active Fuel Management and Honda's Variable Cylinder Management, it deactivates one bank of the engine's cylinders when the throttle is closed.

<span class="mw-page-title-main">Mitsubishi 4A9 engine</span> Reciprocating internal combustion engine

The Mitsubishi 4A9 engine is the newest family range of all-alloy inline four-cylinder engines from Mitsubishi Motors, introduced in the 2004 version of their Mitsubishi Colt supermini, and built by DaimlerChrysler-owned MDC Power in Germany.

<span class="mw-page-title-main">Mitsubishi 4B1 engine</span> Reciprocating internal combustion engine

The Mitsubishi 4B1 engine is a range of all-alloy straight-4 piston engines built at Mitsubishi's Japanese "World Engine" powertrain plant in Shiga on the basis of the Global Engine Manufacturing Alliance (GEMA). Although the basic designs of the various engines are the same, their exact specifications are individually tailored for each partner. The cylinder block and other basic structural parts of the engine were jointly developed by the GEMA companies, but the intake and exhaust manifolds, the cylinder head's intake and exhaust ports, and other elements related to engine tuning were independently developed by Mitsubishi.

<span class="mw-page-title-main">Mitsubishi 6B3 engine</span> Reciprocating internal combustion engine

The Mitsubishi 6B3 engine is a range of all-alloy piston V6 engines developed by Mitsubishi Motors. Currently, only one engine has been developed, a 3.0 L (2,998 cc) V6 first introduced in the North American version of the second generation Mitsubishi Outlander which debuted in October 2006.

Variable valve lift (VVL) is an automotive piston engine technology which varies the height a valve opens in order to improve performance, fuel economy or emissions. There are two main types of VVL: discrete, which employs fixed valve lift amounts, and continuous, which is able to vary the amount of lift. Continuous valve lift systems typically allow for the elimination of the throttle valve.

<span class="mw-page-title-main">Internal combustion engine</span> Engine in which the combustion of a fuel occurs with an oxidizer in a combustion chamber

An internal combustion engine is a heat engine in which the combustion of a fuel occurs with an oxidizer in a combustion chamber that is an integral part of the working fluid flow circuit. In an internal combustion engine, the expansion of the high-temperature and high-pressure gases produced by combustion applies direct force to some component of the engine. The force is typically applied to pistons, turbine blades, a rotor, or a nozzle. This force moves the component over a distance, transforming chemical energy into kinetic energy which is used to propel, move or power whatever the engine is attached to.

References

  1. 1 2 "Cylinder Deactivation Reborn - Part 1, Autospeed, Issue 342, Michael Knowling". 2005-08-03. Archived from the original on 2011-07-28.
    "Cylinder Deactivation Reborn - Part 2, Autospeed, Issue 343, Michael Knowling". Autospeed AU. 2005-08-10. Archived from the original on 2012-03-31.
  2. ↑ Siuru, Bill. "Save Gas: Cylinders get Smart". www.greencar.com. Archived from the original on 2009-07-03.
  3. 1 2 3 "FindArticles.com - CBSi". www.findarticles.com.
  4. 1 2 3 Sabadin, Vittorio (15 April 1983). "L'Alfa riduce i consumi "staccando" i cilindri". La Stampa (in Italian). p. 25. Retrieved 6 March 2015.
  5. 1 2 Fenu, Michele (7 May 1982). "Alfa, il motore modulare per contenere i consumi". La Stampa (in Italian). p. 19. Retrieved 6 March 2015.
  6. ↑ ""Mitsubishi Motors Web Museum", Mitsubishi Motors website". Archived from the original on 2011-07-16.
  7. 1 2 ""Mitsubishi Motors History", Mitsubishi Motors South Africa website". Archived from the original on 2007-01-25. Retrieved 2007-03-12.
  8. 1 2 3 "Mountain of MIVECs" Archived 2007-05-05 at the Wayback Machine , Michael Knowling, AutoSpeed, Issue 346, September 3, 2005
  9. ↑ Fukui, Toyoaki; Nakagami, Tatsuro; Endo, Hiroyasu; Katsumoto, Takehiko; Danno, Yoshiaki (1983). "Mitsubishi Orion-MD — A New Variable Displacement Engine". SAE Transactions. 92, section 3: 362–370. JSTOR   44647614.
  10. ↑ Hartley, John (1982-06-05). "Putting on the pressure". Autocar . Vol. 156, no. 4459. IPC Business Press Ltd. pp. 35–36.
  11. ↑ Fukui et al, p.367
  12. ↑ Higbee, Arthur (20 November 1992). "Mitsubishi Engine Switches Cylinders". The New York Times . Retrieved 28 October 2013.
  13. 1 2 3 EPA, OAR, OTAQ, US. "Vehicles and Engines" (PDF). www.epa.gov.
  14. ↑ "Cylinder Deactivation", About.com, Christine & Scott Gable
  15. ↑ Siuru, Bill. "Variable Displacement for Better MPG". www.greencar.com. Archived from the original on 2012-05-08. Retrieved 2009-11-30.
  16. ↑ "2019 Silverado Leads Industry With Dynamic Fuel Management". media.gm.com. 2018-05-18. Retrieved 2019-02-26.
  17. ↑ Tripathi, Adya; Shost, Mark; Switkes, Joshua; Wilcutts, Mark (2013-04-08). "Design and Benefits of Dynamic Skip Fire Strategies for Cylinder Deactivated Engines". SAE International Journal of Engines. 6 (1): 278–288. doi:10.4271/2013-01-0359. S2CID   110333295.
  18. ↑ "GM adopts advanced cylinder deactivation for 2019 Chevy Silverado V8s". www.sae.org. Retrieved 2019-02-26.
  19. ↑ "Active Cylinder Technology (ACT)". Archived from the original on 2017-06-21. Retrieved 2018-01-21.
  20. ↑ "Three cylinders become two to improve EcoBoost engine efficiency". newatlas.com. 30 November 2016. Retrieved 2017-10-25.
  21. ↑ "2018 Mazda CX-5 Adds Cylinder Deactivation". 22 November 2017.
  22. ↑ "Mazda's New Cylinder-Deactivation Offers Improved Fuel-Efficiency Without Sacrificing Driving Performance". 20 December 2017.
  23. ↑ "Highlights of the Automotive Trends Report". November 2021.
  24. ↑ "乐天娱乐_乐天国际娱乐平台注册㊣24小时在线服务*注册送彩金*》入口". www.hefleyengine.com.
  25. ↑ "The Piston Deactivation Engine". www.scalzoautomotiveresearch.com.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.