GM Whirlfire engine

Last updated
Whirlfire
Allison GMT-305 (cutaway).png
Cutaway of the Detroit Diesel Allison GMT-305, the commercialized derivative of the GT-305Whirlfire gas turbine engine
Overview
Manufacturer General Motors Research / Detroit Diesel Allison
Production1953–83
Layout
Compression ratio single-stage, rotary
Combustion
Operating principle free-turbine turboshaft

The GMWhirlfire gas turbine engines were developed in the 1950s by the research division of General Motors Corporation and fitted to concept vehicles, including the Firebird concept cars, Turbo-Cruiser buses, and Turbo-Titan trucks through the 1960s. They are free-turbine turboshaft machines with two spools: one compressor/gasifier turboshaft and one power/output turboshaft sharing a common axis without a mechanical coupling between them. Fuel consumption of the first-generation GT-300 was high compared to piston engines, so thermal wheel regenerators were added to the second-generation GT-304, cutting consumption by approximately 1⁄2.

Contents

Initially, the engines were built by GM Research, but starting with the third generation GT-305, the Allison Engine division took over responsibility for commercializing gas turbine technology. This division, later merged with Detroit Diesel and renamed Detroit Diesel Allison, would produce approximately one hundred of the final design GT-404 engines, which incorporated ceramic components. Cost, driven by exotic turbine alloys and materials, and fuel consumption proved to be insoluble issues compared to conventional piston engines and further development of gas turbine engines at General Motors was discontinued in the early 1980s.

Design

Because the Whirlfire engines are free-turbine machines, maximum torque is developed when the output shaft is stalled (not turning), and is approximately double the torque developed at full power output. In addition, the lowest fuel consumption is achieved at full power. [1] : 45–46 

Gas path

In the third-generation GT/GMT-305, the air intake is arranged axially with the turboshafts, which share a common horizontal axis. The single-stage rotary compressor draws air at atmospheric conditions through the intake and expels compressed air out radially into the side compartments, where the rotating drum-shaped regenerators preheat the compressed air using heat extracted from the exhaust gases. The compressed air is channeled through the combustors, where it is mixed with fuel and burned, and the resulting combustion gases are expanded through first the gasifier turbine, which is on the same shaft and is used to drive the rotary compressor, then through the power turbine, which is on the output shaft. [1] : 43–44 

At the gasifier turbine inlet, the design temperature is 1,650 °F (900 °C). For the GMT-305, the rotary speed of the gasifier/compressor shaft is 33,000 RPM, while the power shaft turns at 24,000 RPM at full power; the power shaft speed is stepped down to 3,500 RPM through reduction gearing at the output to make it compatible with automotive components. A governor allows the output shaft to turn up to 4,500 RPM. [1] : 43–44  An accessory shaft is driven from the gasifier/compressor shaft for engine ancillaries, including a gear-type lubrication oil pump. [1] : 44 

Regeneration

Initially, the first engines developed (GT-300 and 302) did not have a regenerator, but adding regeneration to recapture heat from the exhaust gases was found to reduce fuel consumption by 1⁄2 for the second-generation GT-304, so subsequent generations of GM Whirlfire gas turbine engines incorporated a regenerator.

For the GT/GMT-305, two drum regenerators are arranged to either side of the turboshafts in large compartments; the regenerators turn at approximately 30 RPM. Within each side compartment, a vertical bulkhead divides the regenerators into low-pressure exhaust (occupying approximately 2⁄3 of the regenerator) and high-pressure inlet (the remaining 1⁄3) sections. As a regenerator rotates through the exhaust section, it picks up waste heat from the exhaust gases, then as it continues to rotate into the inlet section, the heat is transferred to the compressed air, preheating it before fuel is added in the combustors. [1] : 44 

In addition to improving thermodynamic efficiency, the regenerators serve to muffle engine noise and heat, reducing exhaust temperatures. [1] : 44  The exhaust section operates at a lower pressure than the inlet section, so regenerator sealing is important to minimize loss of high-pressure compressed air. [2]

Engine braking

In a conventional piston engine, engine braking can be used to slow a vehicle without use of the friction brakes; because the power turbine is not mechanically connected to the compressor in a free-turbine turboshaft engine, a similar effect cannot be accomplished. During the development of the Whirlfire engines, GM found the gasifier turbine could generate more power than was required to operate the compressor, so for the fifth-generation GT-309 (1964), GM and Allison coupled the gasifier and power turboshafts using a clutch to extract some of that surplus power. The resulting system, which Allison branded Power Transfer, gave the GT-309 an engine braking effect and improved fuel economy at partial load. [3]

Fuel

As external combustion engines, the GM Whirlfire gas turbines were capable of burning a wide variety of fuels; for example turbine engines burning powdered coal were fitted to a Cadillac Eldorado and Oldsmobile Delta 88 in the early 1980s as a response to the 1979 oil crisis. [4] [5] Other potential sources of fuel included methanol, ethanol, liquefied coal, and shale oil. [6]

Models

Whirlfire gas turbine specifications
EngineOutputTurboshaft speed (RPM) BSFC (lb/hp·hr)WeightApplicationsNotes & Refs.
PowerTorqueGasifierPower
GT-300325 hp (242 kW)26,00013,0001.63775 lb (352 kg)Turbo-Cruiser INo regenerator [7]
GT-302370 hp (280 kW)26,00013,0001.63775 lb (352 kg)Firebird ITwo-burner version of GT-300 [7]
GT-304200 hp (150 kW)35,00028,0000.77850 lb (390 kg)Firebird II, Turbo-Titan IFirst to be equipped with a regnerator to improve fuel consumption [8]
GT-305225 hp (168 kW)33,00027,0000.55600–650 lb (270–290 kg)Firebird III, Turbo-Titan IICommercialized by Detroit Diesel Allison Division as GMT-305
GT-309280 hp (210 kW)875 lb⋅ft (1,186 N⋅m)35,70035,0000.45950 lb (430 kg)Turbo-Titan III, Turbo-Cruiser II/III, RTX, RTS 3T"Power Transfer" system enables engine braking [9]
GT-404325 hp (242 kW)595 lb⋅ft (807 N⋅m)37,10330,8300.4751,700 lb (770 kg) GMC Astro, MCI MC-8, RTS (prototypes) [10]

GT-300/302

Firebird I / XP-21 is powered by the GT-302 Firebird I in Motion expo.jpg
Firebird I / XP-21 is powered by the GT-302

The first engine, carrying an internal designation of GT-300 (1953), did not have a regenerator. The GT-300 had an output of 370 hp (280 kW) when the gasifier (compressor) turbine was spinning at 26,000 RPM and the free (power) turbine was spinning at 13,000 RPM. The weight of the entire engine unit was 775 lb (352 kg). The GT-300 was fitted to an "Old Look" transit bus, which was branded "Turbo-Cruiser". [11] To reduce overall size, the single large burner was replaced by two smaller burners and the engine was re-designated GT-302, which was fitted to Firebird I (XP-21). [1] : 43  [9] [12] [13]

The GT-300 was designed with a 3.5:1 compression ratio and nominal design turboshaft speeds of 24,000 RPM (gasifier) and 12,000 RPM (power). Engine accessories are driven by the gasifier turboshaft through a perpendicular bevel gear arrangement; a conventional automotive starting motor is used to crank the accessory drive shaft (and gasifier turboshaft). [14] A new nickel-base alloy, designated GMR-235, was developed and patented for the turbine blades in the Whirlfire engine. [15] [16]

Externally, the Turbo-Cruiser was distinguished from piston-powered buses by "turbocruiser" script lettering on the sides, blanked-out rear windows, and a large central exhaust stack at the roof. The rearmost seats were replaced by "a complete mobile laboratory with a large [rear-facing] instrumentation panel" for two engineers. [17] : 22  Operating experience with the Turbo-Cruiser showed the engine's mechanical durability; according to W.A. Turunen, "on several occasions, pieces of instrumentation have passed through the machine. The turbine buckets were bent, but in no instance did they fail even after subsequent running of damaged parts." [17] : 23  The bus accumulated 9,000 mi (14,000 km) in testing. [18] : 330 

Brake-specific fuel consumption (BSFC) was a notable issue, which at 1.63 lb/hp·h [19] was significantly greater than that of a comparable Detroit Diesel 8V71 diesel engine (approximately 0.40 lb/hp·h), [20] even though the turbine was 1,500 lb (680 kg) lighter. Other planned improvements would target throttle lag, which was caused by accelerating the gasifier turbine to peak speed, and lack of engine braking. [21]

GT-304

GT-304 (1956) was the first GM gas turbine to include a regenerator, which used exhaust heat to warm intake air, improving fuel consumption to 0.77 lb/hp·h. [19] As fitted to Firebird II, GT-304 output was 200 hp (150 kW) at a gasifier turbine speed of 35,000 RPM. The gasifier turbine idled at 15,000 RPM and the power turbine operated at up to 28,000 RPM. Overall compression ratio in the gasifier stage was 3.5:1. [22] Turbine inlet temperature was increased to 1,650 °F (900 °C) from 1,500 °F (820 °C); after GM Research re-rated the temperature resistance of the GMR-235 superalloy. With the regenerators, the engine weight increased to 850 lb (390 kg); [23] : 31  each regenerator was 150 lb (68 kg). [18] : 340  7.27:1 reduction gearing made the output shaft speed compatible with conventional automobile accessories. A fluid input coupling was used between the engine and transmission; in addition, larger accessories were powered from the transmission, not the gasifier turboshaft, as it had been discovered that at idle, accessory power draw could exceed available surplus power. [23] : 31–32 

The GT-304 also was fitted to the first Turbo-Titan, a heavy-duty Chevrolet Model 10413 truck-tractor with tandem rear axles; Turbo-Titan was tested with various loads, demonstrating superior acceleration and gradeability compared to the Loadmaster V-8 engine that was removed, a 322 cu in (5.3 L) overhead valve V-8 with 195 hp (145 kW) output. [17]

GT-305

The GT-305 (1958) fitted to Firebird III had an output of 225 hp (168 kW) (at turbine speeds of 33,000 RPM gasifier / 27,000 RPM power) [24] and weight of 600–650 lb (270–290 kg). [25] With a regenerator and additional component refinements, GT-305 achieved a brake-specific fuel consumption of 0.55 lb/hp·h, [19] an improvement of 25% compared to the earlier GT-304; similarly, the engine weight of the GT-305 was reduced by 25% compared to the 304. External dimensions were 37 in (940 mm) long, 27.8 in (710 mm) high, and 26 in (660 mm) wide. [26] Exhaust temperature had been reduced considerably; the GT-305 exhaust was 520 °F (271 °C) at full power, decreasing to 275 °F (135 °C) at idle. [18] : 346 

Firebird III had a two-cylinder auxiliary power unit for accessories and a special grade retarder to simulate engine braking, which Jan Norbye criticized as resulting from "the refusal of the turbine experts to tackle the problems at the base ... these two systems seem of dubious value except in an application where cost is no object". [18] : 358–359 

The engine was redesignated GMT-305 in 1959 and further development for regular production was handed off from GM Research to Allison Transmission. [19] [1] : 43  As the GMT-305, it incorporated approximately 30 lb (14 kg) of nickel in alloys, including the turbine blades (GMR-235), turbine wheels (16-25-6), turboshafts (4340), turbine bolts (Inconel X), turbine and bulkhead casings (SAE 60347), and combustion chambers (Hastelloy X). [27] The first GMT-305 prototypes began shipping in November 1959 for fitment to U.S. military vehicles, including the M56 Scorpion and a 28-foot personnel boat. [28] The Whirlfire-powered M56 underwent winter conditions testing and accumulated 1,000 mi (1,600 km) of service with little trouble. [29] In addition, the GMT-305 was fitted to an ore-hauling truck at an open-pit nickel mine in Sudbury, Ontario. [27]

GT-309

GT-307, a proposed successor to GT-305, was designed in 1960 but never built. [18] : 369  Instead, GM moved away from passenger cars with GT-309 (1964), which was designed for heavy-duty applications, as demonstrated by its use in the Chevrolet Turbo Titan III truck and Turbo-Cruiser II/III buses; for this updated engine, the gasifier turbine and compressor were designed to operate at 35,700 RPM, generating 280 hp (210 kW) at a power shaft speed of 35,000 RPM (with reduction gearing, 4,000 RPM). Stall torque was 875 lb⋅ft (1,186 N⋅m) at idle. [30] [9] In addition, the GT-309 was fitted to a conventional GMC Astro-95 cabover tractor and the RTX transit bus prototype of 1969. [18] : 379, 382 

Compared to earlier engines, the turbine inlet temperature was increased again to 1,700 °F (930 °C). [31] The gasifier (compressor) shaft idled at 15,000 RPM and BSFC was 0.45 lb/hp·h. A "power transfer" system was used to harness some of the gasifier turbine to the output shaft; with this engaged, engine braking was available at an effectiveness of two to three times the equivalent effect as using a piston engine. The engine used a single rotating drum regenerator, moved to the top of the engine with a single combustor. [32] With this reconfiguration, GT-309 measured 36 in (910 mm) long, 30 in (760 mm) wide, and 35.5 in (900 mm) high, consuming air at a rate of 4 lb/s (110 kg/min) with a compression ratio of 3.9:1. [18] : 370–371  Whenever the transmission was in gear, the engine operated at a ready-idle speed of 19,300 RPM (gasifier turboshaft) and was capable of accelerating to 32,130 RPM in 2.7 seconds to combat throttle lag. [18] : 371–373  The single regenerator preheated the compressed air from 400 to 1,100 °F (204 to 593 °C), resulting in exhaust gas temperatures of less than 500 °F (260 °C). [18] : 375 

Unlike the GT-305, commercial development of the GT-309 was handled by Detroit Diesel instead. However, Detroit Diesel and Allison were merged in 1970, resulting in the Detroit Diesel Allison Division of General Motors Corporation (DDAD), reuniting road vehicle gas turbine development in GM. [18] : 382 

GT-404/505/606

GT-404, exploded view Allison GT-404 (exploded).png
GT-404, exploded view

The final evolution of the GM gas turbine engine was the GT-404, which was developed by DDAD and had dropped the Whirlfire branding. GT-404 output was 325 hp (242 kW) at gasifier / power turbine speeds of 37,103 / 30,830 RPM, with a stall torque of 595 lb⋅ft (807 N⋅m) and BSFC of 0.475 lb/hp·h. [33] Compared to the preceding GT-309, the 404 returned to dual side-mounted regenerators, although the 404 used discs rather than drums. [34] : 79  The 404 was considerably larger and heavier than the preceding 309, at 47 in × 28 in × 39 in (1,190 mm × 710 mm × 990 mm) (W×L×H) and 1,700 lb (770 kg). [18] : 383  A special version of the Allison Transmission HT-740 heavy-duty automatic transmission was planned to be mated with the GT-404, which omitted the torque converter and saved some space. [18] : 386 

The first GT-404 engines were shipped from the Detroit Diesel Allison plant in Indianapolis to Detroit and Portland, Oregon in 1971, for installation in prototype over-the-road tractors. [35] In addition, it served in the electrical power generator set for the MIM-104 Patriot surface-to-air missile fire unit. [36] The list price of the first versions, at US$9,000(equivalent to $50,000 in 2023), reportedly was "barely adequate to cover production costs" and not competitive with conventional diesel engines. [18] : 387  Serial production was scheduled to begin in 1972, and GT-505 and 606 variants were planned to follow in 1973, with increased outputs of 400–450 hp (300–340 kW) (505) and 550 hp (410 kW) (606). [37] Limited field experience with the 404 was obtained between 1974 and 1977, [38] including use in MC-7 Super 7 Turbocruiser buses for Greyhound. [39] Later versions of the 404 used advanced materials, including aluminum silicate ceramic disc regenerators. [34] : 79 

The GM RTS-3T candidate prototype (1972) tested under the Transbus Program also used a GT-404. In the late 1970s, the U.S. Departments of Energy and Transportation jointly conducted the Gas Turbine Transit Bus Demonstration Program, using the DDA GT-404 gas turbine in both transit buses and highway coaches. [40] [41] 11 GT-404-4 engines were built for this program; this version was rated at a nominal 300 hp (220 kW) output with a turbine inlet temperature of 1,875 °F (1,024 °C); [34] : 77  as-shipped, tested engine output varied from 282.8–304.3 hp (210.9–226.9 kW), with BSFC between 0.428 to 0.447 lb/hp·h. [34] : 92  Under the demonstration program, four GT-404-powered RTS-II (T8H-603) transit buses and four MCI MC-8 Americruiser coaches were placed into revenue service for the MTA (in Baltimore, Maryland) and Greyhound Lines, respectively. The MTA terminated its test in July 1981 after three months in revenue service; [34] : 51  by the time the study concluded in 1983, it had been placed under the auspices of NASA. [42]

Because GM declined to convert the RTS-II buses to accommodate the turbine engines, a fabricator was contracted to custom install them; the GT-404-4 engines were hand-built at a per-unit cost of US$250,000(equivalent to $1,170,000 in 2023). [42] : I-5, I-6  Externally, the modified RTS-II turbine buses for MTA required a boxy cover at back of the bus to accommodate the relocated air conditioning condenser, changing the profile from a slanted rear end to a boxier look. [34] : 117  The turbine engines were installed in Greyhound MC-8 fleet numbers 5991 (engine T6), 5992 (T5, later T8), 5993 (T7), and 5994 (T5, later T9); and MTA RTS-II fleet numbers 3318 (T11), 3319 (T11, later T14), 3320 (T14, later T13), and 3321 (T13, later T15 & T12). Engine T10 was cannibalized for parts before being installed into a bus. [34] : Appendix C  Over 170,610 mi (274,570 km) of service with Greyhound, the four MC-8 buses averaged 4.26 mpg‑US (55.2 L/100 km), less efficient than diesel piston-engined peer coaches, which achieved 5.66 mpg‑US (41.6 L/100 km) on average. Similarly, over 19,660 mi (31,640 km) of revenue service with MTA, the four RTS-II buses averaged 2.7 mpg‑US (87 L/100 km), consuming more than peer transit buses, which averaged 4.3 mpg‑US (55 L/100 km) on similar routes. [34]

See also

Related Research Articles

<span class="mw-page-title-main">Turbocharger</span> Exhaust-powered forced-induction device for engines

In an internal combustion engine, a turbocharger is a forced induction device that is powered by the flow of exhaust gases. It uses this energy to compress the intake air, forcing more air into the engine in order to produce more power for a given displacement.

<span class="mw-page-title-main">Gas turbine</span> Type of internal and continuous combustion engine

A gas turbine, gas turbine engine, or also known by its old name internal combustion turbine, is a type of continuous flow internal combustion engine. The main parts common to all gas turbine engines form the power-producing part and are, in the direction of flow:

<span class="mw-page-title-main">Pratt & Whitney Canada PT6</span> Turboprop aircraft engine family by Pratt & Whitney Canada

The Pratt & Whitney Canada PT6 is a turboprop aircraft engine produced by Pratt & Whitney Canada. Its design was started in 1958, it first ran in February 1960, first flew on 30 May 1961, entered service in 1964, and has been continuously updated since. The PT6 consists of two basic sections: a gas generator with accessory gearbox, and a free-power turbine with reduction gearbox. In aircraft, the engine is often mounted "backwards," with the intake at the rear and the exhaust at the front, so that the turbine is directly connected to the propeller. Many variants of the PT6 have been produced, not only as turboprops but also as turboshaft engines for helicopters, land vehicles, hovercraft, and boats; as auxiliary power units; and for industrial uses. By November 2015, 51,000 had been produced, which had logged 400 million flight hours from 1963 to 2016. It is known for its reliability, with an in-flight shutdown rate of 1 per 651,126 hours in 2016. The PT6A turboprop engine covers the power range between 580 and 1,940 shp, while the PT6B/C are turboshaft variants for helicopters.

<span class="mw-page-title-main">Rolls-Royce T406</span> Rolls-Royce North America turboshaft aircraft engine (1986)

The Rolls-Royce T406 is a turboshaft engine that powers the Bell Boeing V-22 Osprey tiltrotor. The engine delivers 6,000 shp (4,470 kW).

<span class="mw-page-title-main">Turboshaft</span> Gas turbine used to spin a shaft

A turboshaft engine is a form of gas turbine that is optimized to produce shaft horsepower rather than jet thrust. In concept, turboshaft engines are very similar to turbojets, with additional turbine expansion to extract heat energy from the exhaust and convert it into output shaft power. They are even more similar to turboprops, with only minor differences, and a single engine is often sold in both forms.

<span class="mw-page-title-main">Allison T56</span> American-built military turboprop (1954–)

The Allison T56 is an American single-shaft, modular design military turboprop with a 14-stage axial flow compressor driven by a four-stage turbine. It was originally developed by the Allison Engine Company for the Lockheed C-130 Hercules transport entering production in 1954. It has been a Rolls-Royce product since 1995 when Allison was acquired by Rolls-Royce. The commercial version is designated 501-D. Over 18,000 engines have been produced since 1954, logging over 200 million flying hours.

Allison Transmission Holdings Inc. is an American manufacturer of commercial duty automatic transmissions and hybrid propulsion systems. Allison products are specified by over 250 vehicle manufacturers and are used in many market sectors, including bus, refuse, fire, construction, distribution, military, and specialty applications.

The General Motors Firebird comprises a quartet of prototype cars that General Motors (GM) engineered for the 1953, 1956, and 1959 Motorama auto shows. The cars' designers, headed by Harley Earl, took Earl's inspiration from the innovations in fighter aircraft design at the time. General Motors never intended the cars for production, but rather to showcase the extremes in technology and design that the company was able to achieve.

<span class="mw-page-title-main">Allison Model 250</span> Turboshaft aircraft engine

The Allison Model 250, now known as the Rolls-Royce M250, is a highly successful turboshaft engine family, originally developed by the Allison Engine Company in the early 1960s. The Model 250 has been produced by Rolls-Royce since it acquired Allison in 1995.

<span class="mw-page-title-main">GM "old-look" transit bus</span> GM bus manufactured from 1940 to 1969

The GM "old-look" transit bus was a transit bus that was introduced in 1940 by Yellow Coach beginning with the production of the model TG-3201 bus. Yellow Coach was an early bus builder that was partially owned by General Motors (GM) before being purchased outright in 1943 and folded into the GM Truck Division to form the GM Truck & Coach Division. The Yellow Coach badge gave way to the GM nameplate in 1944. Production of most "old-look" models was stopped upon the release of the GM New-Look bus in 1959, however some smaller "old-look" models continued to be built until 1969. Approximately 38,000 "old-look" buses were built during the 29-year production run. The "old-look" name is an unofficial retronym applied to this series of GM buses after the release of the GM New-Look series.

<span class="mw-page-title-main">Lycoming LTS101</span> Turboshaft engine family

The LycomingLTS101 is a turboshaft engine family ranging from 650 to 850 shaft horsepower, used in a number of popular helicopters, and, as the LTP101 turboprop, light aircraft. Both models carry the US military designation T702. The engine was originally designed at the Lycoming Turbine Engine Division in Stratford, Connecticut, but is now produced by Honeywell Aerospace.

<span class="mw-page-title-main">Turbomeca Turmo</span>

The Turbomeca Turmo is a family of French turboshaft engines manufacturered for helicopter use. Developed from the earlier Turbomeca Artouste, later versions delivered up to 1,300 kW (1,700 shp). A turboprop version was developed for use with the Bréguet 941 transport aircraft.

<span class="mw-page-title-main">Avco-Lycoming AGT1500</span> Turbine engine

The Avco-Lycoming AGT1500 is a gas turbine engine. It is the main powerplant of the M1 Abrams series of tanks. The engine was originally designed and produced by the Lycoming Turbine Engine Division in the Stratford Army Engine Plant. In 1995, production was moved to the Anniston Army Depot in Anniston, Alabama, after the Stratford Army Engine Plant was shut down.

<span class="mw-page-title-main">General Electric T64</span> Turboshaft engine

The General Electric T64 is a free-turbine turboshaft engine that was originally developed for use on helicopters, but which was later used on fixed-wing aircraft as well. General Electric introduced the engine in 1964. The original engine design included technical innovations such as corrosion resistant and high-temperature coatings. The engine features a high overall pressure ratio, yielding a low specific fuel consumption for its time. Although the compressor is all-axial, like the earlier General Electric T58, the power turbine shaft is coaxial with the HP shaft and delivers power to the front of the engine, not rearwards. Fourteen compressor stages are required to deliver the required overall pressure ratio. Compressor handling is facilitated by 4 rows of variable stators. Unlike the T58, the power turbine has 2 stages.

<span class="mw-page-title-main">Boeing T50</span>

The Boeing T50 was a small turboshaft engine produced by Boeing. It was the first turboshaft engine to ever power a helicopter: a modified Kaman K-225 in 1951. Based on Boeing's earlier Model 500 gas generator, the T50's main application was in the QH-50 DASH helicopter drone of the 1950s. An up-rated version designated Model 550 was developed to power the QH-50D and was given the military designation T50-BO-12.

The Boeing T60 was a family of small turboshaft/turboprop engines produced by Boeing, based on Boeing's earlier Model 500 gas generator and Model 502 (T50) turboshaft engines.

<span class="mw-page-title-main">Klimov TV2-117</span> 1960s Soviet turboshaft aircraft engine

The Klimov TV2-117 is a Soviet gas-turbine turboshaft engine intended for helicopter use. Designed in the early 1960s by the Isotov Design Bureau the engine became the first purpose built gas turbine engine for helicopter use by the Soviet Union with previous helicopter turbines being adapted aeroplane powerplants. It was later produced by Klimov, production ending in 1997.

<span class="mw-page-title-main">MAN Turbo 6022</span> 1960s German turboshaft aircraft engine

The MAN Turbo 6022 is a German gas turbine turboshaft engine for helicopter use. Designed in the early 1960s by BMW the engine powered the third prototype of the MBB Bo 105 on its maiden flight in December 1967.

The Chevrolet Turbo Titan III was a gas turbine-powered concept cabover heavy truck designed and built as a working prototype by General Motors in 1965. It was accompanied by a matching custom trailer built in stainless steel; the Turbo Titan III was first shown to the public at the 1965 session of the 1964 New York World's Fair.

The Allison T78 was a turboprop engine that first ran in March 1965. It used a regenerator that recovered and reused exhaust heat to reduce fuel consumption.

References

  1. 1 2 3 4 5 6 7 8 Fetters, J.C. (April 6–7, 1959). "Allison Division of General Motors Corporation". Proceedings. Gas Turbine Progress Meeting. WAshington, D.C. pp. 35–50.
  2. ↑ Vickers, Paul T. (March 8–11, 1959). Rotary Regenerators for the Whirlfire Vehicular Turbines. Gas Turbine Power Conference. Cincinnati, Ohio: The American Society of Mechanical Engineers. doi:10.1115/59-GTP-12.
  3. ↑ Lyndall, Jack (November 1964). "The coming age of turbine power ... can it meet the challenge of tomorrow's superhighways?". Fleet Owner. Retrieved 19 September 2022.
  4. ↑ Piot, D.K. (June 18, 1981). "Powdered coal: auto firm tests its potential as a gasoline substitute". The Christian Science Monitor. Retrieved 19 September 2022.
  5. ↑ Roy, Rex (January 2, 2009). "Coal in Your Stocking? Fuel Up the Cadillac" . The New York Times. Retrieved 19 September 2022.
  6. ↑ Holusha, John (June 4, 1981). "G.M. Displays Car Fueled With Coal Dust". The New York Times. Retrieved 19 September 2022.
  7. 1 2 Turunen, W. A. (1955). "Pinwheels or Pistons? — A Progress Report on Automotive Gas Turbines, SAE Technical Paper 550236". Transactions. 63. SAE International: 72–83. doi:10.4271/550236. JSTOR   44468550.
  8. ↑ Turunen, W.A.; Collman, J.S. (1957). "The Regenerative Whirlfire Engine for Firebird II". Transactions. 65. SAE International: 478–487. JSTOR   44564383.
  9. 1 2 3 Turunen, W.; Collman, J. (1965). "The General Motors Research GT-309 Gas Turbine Engine". SAE Transactions. 74: 357–377. doi:10.4271/650714. JSTOR   44554219.
  10. ↑ Amann, C.A. (1973). "An Introduction to the Vehicular Gas Turbine Engine". Transactions. 82. SAE International: 2197–2215. JSTOR   44717615.
  11. ↑ Brophy, Jim (June 2, 2018). "Bus Stop Classics: General Motors (GM) Turbo Cruiser I, II and III Urban Transit Coaches — Maverick (Top Gun), Your Bus is Here ..." Curbside Classic. Retrieved 8 February 2022.
  12. ↑ "The XP-21 Firebird: General Motors' Newest Experiment on Wheels" (PDF). General Motors. 1954. Retrieved 13 September 2022.
  13. ↑ "GM's XP21 'Firebird' Exhibited in Motorama". AllisoNews. Vol. XIII, no. 30. Allison Division, General Motors Corporation. January 22, 1954. Retrieved 13 September 2022.
  14. ↑ Turunen, W.A. (1963). "Pinwheels or Pistons? A Progress Report on Automotive Gas Turbines". In Carroll, William (ed.). Automotive Gas Turbines . Studio City, California: Coda Publications. pp. 12–17. Retrieved 19 September 2022.
  15. ↑ Hanink, D.K.; Webbere, F.J.; Boegehold, A.L. (1955). "Development of a New Gas Turbine Super Alloy GMR-235". Transactions. SAE Technical Paper Series. 63. SAE International: 704–716. doi:10.4271/550288. JSTOR   44468603.
  16. ↑ US 2688536,Callaway, Samuel R.&Webbere, Fred J.,"High-temperature creep resistant alloy",published 1954-09-07, assigned to General Motors Corporation
  17. 1 2 3 Carroll, William, ed. (1963). "Chevrolet Turbine-Powered Cross Country Truck Test". Automotive Gas Turbines . Studio City, California: Coda Publications. pp. 18–24. Retrieved 19 September 2022.
  18. 1 2 3 4 5 6 7 8 9 10 11 12 13 Norbye, Jan P. (1975). "18. Case History: General Motors". The Gas Turbine Engine: Design, Development, Applications . Radnor, Pennsylvania: Chilton Book Company. p. 319. ISBN   0-8019-5753-2 . Retrieved 19 September 2022.
  19. 1 2 3 4 "Allison Given Responsibility For Marketing Whirlfire GMT-305 Gas Turbine Engine". AllisoNews. Vol. XVIII, no. 28. Allison Division, General Motors Corporation. January 16, 1959. pp. 1, 4. Retrieved 13 September 2022.
  20. ↑ "Truck Model 8V-71TT, 305 hp" (PDF). Detroit Diesel Allison. July 1975. Retrieved 15 September 2022.
  21. ↑ Kincaid, Kenneth (1955). "A Report on Gas Turbines". Automobile Yearbook. True (magazine). pp. 64–69. Retrieved 13 September 2022.
  22. ↑ "The story of Firebird II | 'THREE-ZERO-FOUR': The Gas Turbine Family Car, General Motors latest 'laboratory on wheels'" (PDF). General Motors. 1956. Retrieved 13 September 2022.
  23. 1 2 Turunen, W.A. (1963). "The Regenerative Whirlfire Engine for the Firebird II". In Carroll, William (ed.). Automotive Gas Turbines . Studio City, California: Coda Publications. pp. 28–33. Retrieved 19 September 2022.
  24. ↑ "Introducing the newest General Motors 'laboratory on wheels...' an amazing experience in automatic car control! Firebird III" (PDF). General Motors. 1962. Retrieved 13 September 2022.
  25. ↑ "New Firebird III Unveiled by GM". AllisoNews. Vol. XVIII, no. 11. Allison Division, General Motors Corporation. September 19, 1958. Retrieved 13 September 2022.
  26. ↑ "Briefing the Record: Firebird III". Mechanical Engineering. Vol. 80, no. 11. The American Society of Mechanical Engineers. November 1958. p. 111.
  27. 1 2 Schwartz, F.L. (May–June 1960). "'Whirlfire' Hauls Ore". Gas Turbine. Vol. 1, no. 3. Stamford, Connecticut: Gas Turbine Publications, Inc. pp. 32–33.
  28. ↑ "First Prototype Whirlfire Engine Shipped to Ordinance". AllisoNews. Vol. XIX, no. 21. Allison Division, General Motors Corporation. November 25, 1959. Retrieved 13 September 2022.
  29. ↑ "Allison GMT-305 Whirlfire Engine Completes Arctic Test Program in Manitoba". AllisoNews. Vol. XIX, no. 41. Allison Division, General Motors Corporation. April 15, 1960. pp. 1, 4. Retrieved 13 September 2022.
  30. ↑ Senefsky, Bill (September 1, 2003). "Chevrolet Turbo-Titan III Concept Vehicle – Space Truckin'". Motor Trend. Retrieved 8 February 2022.
  31. ↑ Wade, W.R.; Cornelius, W. (September 27–28, 1971). Walter Cornelius; William G. Agnew (eds.). Emission Characteristics of Continuous Combustion Systems of Vehicular Powerplants — Gas Turbine, Steam, Stirling. Symposium on Emissions from Continuous Combustion Systems. Warren, Michigan: Plenum Press. ISBN   0-306-30702-2.
  32. ↑ "Turbo-Titan III ... a glimpse into tomorrow's trucking!" (PDF). Chevrolet. 1965. Archived from the original (PDF) on 2023-03-29. Retrieved 2022-09-15.
  33. ↑ Best, G.C.; Flanigan, E.E. (March 26–30, 1972). Allison GT-404—The VIP Engine-Versatile Industrial Power. Gas Turbine and Fluids Engineering. San Francisco, California: The American Society of Mechanical Engineers. doi: 10.1115/72-GT-93 .
  34. 1 2 3 4 5 6 7 8 Nigro, D.N.; Stewart, R.G.; Apple, S.A. (March 1982). Support and Power Plant Documentation for the Gas Turbine Powered Bus Demonstration Program (PDF) (Report). National Aeronautics and Space Administration, Lewis Research Center. Retrieved 16 September 2022.
  35. ↑ "First of New Gas Turbines Shipped from Indianapolis". Power News. Vol. 1, no. 4. Detroit Diesel Allison Division of General Motors. May 1971. Retrieved 15 September 2022.
  36. ↑ "Salute the Patriot". Power News. Vol. 12, no. 1. Detroit Diesel Allison Division of General Motors Corporation. January–February 1982. Retrieved 15 September 2022.
  37. ↑ Marunas, P. Raymond (February 1973). "Marine Power: Detroit Diesel Allison Raises New Turbine Family". Motor Boating & Sailing. Vol. 131, no. 2. New York, New York: The Hearst Corporation. p. 86. Retrieved 19 September 2022.
  38. ↑ Flanigan, E.; Nigro, D. (1979). Field Experience with the Detroit Diesel Allison 404/505 Industrial Gas Turbine Engines. Automotive Engineering Congress and Exposition. doi:10.4271/790129.
  39. ↑ "Division Extends a Welcome to Conference on Cities Group". Power News. Vol. 1, no. 5 (Detroit ed.). Detroit Diesel Allison Division of General Motors Corporation. June 1971. p. 2. Retrieved 19 September 2022.
  40. ↑ Booz, Allen & Hamilton (April 1978). Dept. of Energy/Dept. of Transportation Gas Turbine Transit Bus Demonstration Program: Program Plan (Report). U.S. Department of Energy. Retrieved 15 September 2022.
  41. ↑ Nigro, D. N. (July 1979). Gas Turbine Engines and Transmissions for Bus Demonstration Programs | Technical Status Report for Period 30 April 1979 - 31 July 1979 (PDF) (Report). Detroit Diesel Allison Division, GMC. Retrieved 15 September 2022.
  42. 1 2 Booz, Allen & Hamilton Inc. (June 1983). Demonstration and Evaluation of Gas Turbine Transit Buses (PDF) (Report). National Aeronautics and Space Administration, Lewis Research Center. Retrieved 15 September 2022.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.