Royal Aircraft Factory R.E.8

Last updated

Royal Aircraft Factory R.E.8
Royal Aircraft Factory R.E.8 - Duxford Airshow 2012.jpg
A vintage R.E.8 performing over the Duxford Jubilee Airshow 2012
Role Reconnaissance, Bomber
Manufacturer Royal Aircraft Factory
Designer John Kenworthy / Walter Barling
First flight17 June 1916
Introduction1916
Retired1918
StatusRetired
Primary users RFC/RAF
Australian Flying Corps
Aviation Militaire Belge
Produced1916–1918
Number built4,077 [1]
Variants Siddeley-Deasy R.T.1

The Royal Aircraft Factory R.E.8 is a British two-seat biplane reconnaissance and bomber aircraft of the First World War that was designed and produced at the Royal Aircraft Factory. It was also built under contract by Austin Motors, Daimler, Standard Motors, Siddeley-Deasy and the Coventry Ordnance Works.

Contents

Intended as a replacement for the vulnerable B.E.2, the R.E.8 was widely regarded as more difficult to fly and gained a reputation in the Royal Flying Corps for being "unsafe" that was never entirely dispelled. Although eventually it gave reasonably satisfactory service, it was never an outstanding combat aircraft. Nonetheless, it remained the standard British reconnaissance and artillery observation aircraft from mid-1917 to the end of the war, serving alongside the rather more popular Armstrong Whitworth F.K.8.

More than 4,000 R.E.8s were eventually produced; these aircraft saw service in a range of different theatres, including Italy, Russia, Palestine and Mesopotamia, as well as the Western Front. The R.E.8 was rapidly withdrawn from service after the end of the war, by which time it was regarded as totally obsolete.

Development

Background

Design of the new type had begun in late 1915, [2] so that it was conceptually at least almost contemporary with the B.E.12 and the B.E.2e – like these earlier types, it was designed for inherent stability in line with the dominant pre-war belief in the necessity of stability to perform the aerial observation role. [3]

The B.E.2 had already been subject to considerable criticism, and a deliberate effort was made to address each of the earlier type's failings. In particular, the more powerful motor was intended to improve the feeble speed and climb of the B.E.2 and to allow a better payload; this permitted the type to operate as a true two-seater: the observer no longer had to be left behind when bombs or a full fuel load were carried. There was no need for his seat to be at the centre of gravity; seated behind the pilot, instead of in front as in the B.E.2, he was in the proper position to operate a machine-gun. Another consequence of the additional engine power was the possibility of fitting a forward-mounted gun for the pilot. [4] [3]

Design and testing

Early production R.E.8 with the small vertical fin. There is no fairing over the sump. R.E.8 (early tail).jpg
Early production R.E.8 with the small vertical fin. There is no fairing over the sump.

As early as March 1916, the design appears to have mostly been settled; features included the selection of a Royal Aircraft Factory 4a air-cooled V12 engine (capable of 140 hp) to power the type along with a sizable fin and rudder. During the early design process, a smaller tail fin was substituted for the original, a step which later caused some controversy. [3] By early April 1916 a mock-up of the R.E.8 had been completed, and construction of a pair of prototypes was underway. On 16 June 1916, the first of these prototypes was submitted for its final pre-flight inspection in advance of the type's maiden flight. [3]

On 17 June 1916, the first R.E.8 test flight was conducted by F.W. Goodden. [5] Goodden would perform all of the early flights with the type; on 1 July 1916, Sefton Brancker was flown by Goodden in the type to Hounslow, London. On 16 July 1916, the second prototype, furnished with a different design of propeller, performed its first flight. [3] During late July 1916, the second of two prototypes was dispatched to France for service trials, the results of which were largely successful, with aircrew being generally quite favourably impressed. During August 1916, the second prototype returned to Farnborough, Hampshire, where it underwent modification based upon its experiences in France. [6]

The R.E.8 possessed a conventional wire-braced fabric-covered wooden structure, along with an unequal-span wing arrangement. [3] The engine installation closely resembled that of the B.E.12, complete with the same large air scoop and similar vertically mounted exhausts protruding over the upper wing to carry the fumes clear of the crew. Apart from the disposition of the cockpits, the main visually distinguishable difference was that the engine was slightly raked back, to improve take off and landing characteristics. [7] The early production R.E.8s were more or less identical to the prototypes. [8]

R.E.8 with enlarged fin, at training unit R.E.8 (trainer).jpg
R.E.8 with enlarged fin, at training unit

The R.E.8 adopted a set of single bay, unequal span wings, identical to those of the earlier B.E.2e; although the span (and thus the wing area) had been increased slightly by the use of a wider upper centre section, and lower stub wings to match. On the B.E.2e, these wings functioned to maintain the stability of the B.E.2c while providing the aircraft with superior levels of manoeuvrability; although the long extensions on the upper wing gave rise to fears they would be prone to collapse if the aircraft was dived too sharply, which in turn did not help to build trust in the aircraft. [4] Several other features, such as the tailplane, were also identical to those previously used upon the B.E.2e.

R.E.8s of No 3 Sqn AFC R.E.8 (3 sqn AFC).jpg
R.E.8s of No 3 Sqn AFC

For the purpose of making the R.E.8 less tiring to fly, the pilot's controls included a wheel to adjust the tailplane incidence in flight and a primitive form of rudder trim (applied to the rudder bar) was provided to alleviate the constant pressure necessary to counteract the torque generated by the propeller. Basic flight controls were installed in the observer's cockpit, which folded out of the way when not in use; these were connected to the elevators, rudder and throttle, but not to the ailerons, and were intended to give observers a chance to make a forced landing if the pilot was killed or incapacitated rather than to offer true dual control. [9]

Although not so underpowered as the B.E.2, the R.E.8 was still handicapped by a less than adequate powerplant, and a model re-engined with the Hispano-Suiza engine was projected as the R.E.8a from quite an early stage. The cowling designed for the liquid-cooled engine closely resembled that of the B.E.12b or the S.E.5a. Supplies of Hispano-Suiza engines, more urgently required for other types, never permitted production of the R.E.8a, although a prototype was constructed and underwent trials during December 1916. [10] Plans to mount Rolls-Royce aero engines, such as the Eagle or Falcon were also abortive, for similar reasons. These engines were in chronically short supply and reserved for various other types in British service, including the Airco DH.4 and the Bristol Fighter.

Production

During August 1916, production of an initial batch of 50 aircraft was commenced by the Royal Aircraft Factory itself. [6] On 25 August, a contract was placed with Austin Motors for the completion of 100 R.E.8s; on 30 August, Siddeley-Deasy was also contracted to produce a further 100 examples. [8] By September 1916, full-scale production was well under way. [11] By the end of September, a further 850 R.E.8s had been ordered from a range of manufacturers. [8] During December 1916, the first contractor-produced R.E.8s began to appear. [12]

The Vickers-Challenger interrupter gear and the Scarff ring were still in short supply, being required for the Sopwith 1½ Strutter and other types; accordingly, a few early R.E.8s were built with a pillar mounting for the observer's gun as an interim measure. An alternative to the pilot's synchronised Vickers had been designed, consisting of a fixed Lewis gun with deflector plates fitted to the propeller, although this was never used, a Vickers gun for the pilot being mounted on the port side of the fuselage in a similar position to that on the B.E.12, at first synchronised by the Vickers-Challenger gear and then by the improved Constantinesco hydraulic gear. [13] [8] Photographs of this armament installation make it clear that the cocking handle of the Vickers gun was in easy reach of the pilot and that a normal Aldis sight was often mounted in the pilot's windscreen, giving the lie to statements that the forward firing gun could not be sighted properly due to its position, although the lack of standisation complicated maintenance in operational squadrons. [14]

In total, 4,077 R.E.8s were constructed; a further 353 aircraft that had been on order were cancelled following the end of the war. Only a handful of production aircraft were actually completed by the Royal Aircraft Factory; the bulk of the work was issued out to several private companies including Austin Motors, Daimler, Standard Motors, Siddeley-Deasy and the Coventry Ordnance Works, which were responsible for the type throughout its production life. [15]

Operational history

The first production aircraft reached 52 Squadron Royal Flying Corps (RFC) in France in November 1916. The inexperienced pilots of 52 Squadron found their new mounts thoroughly dangerous and several were killed spinning in off a stall while attempting to land; they were grateful to return to the B.E.2e by exchanging aircraft with 34 Squadron in January 1917. Experienced pilots had fewer problems with the new type and re-equipment of B.E.2 squadrons continued. Pilot's notes for the R.E.8, prepared in the field, drew attention to the fact that it had a higher landing speed than the B.E.2e (hardly surprising, since it was heavier and had almost the same wing area) and that it gave almost no warning of a stall. [13] This seems to have been the source of most complaints about the type's "trickiness".

Preparing an R.E.8 for a night bombing raid IncendiaryBombsRE8.jpg
Preparing an R.E.8 for a night bombing raid

The Royal Aircraft Factory conducted spinning tests on the type, concluding that the R.E.8 was quite hard to spin and recovered easily; but the fin was redesigned with slightly increased area to improve spin recovery. The modification resulted in the production version being no less stable than the B.E.2e; and while this was an advantage for artillery observation and photography it gave the R.E.8 little chance to out-manoeuvre enemy fighters. An even larger fin was fitted to some R.E.8s used as trainers. Some pilots flew the R.E.8 with an empty reserve fuel tank (or even filled the tank with fire extinguisher fluid) to avoid a perceived tendency of R.E.8s to burn on crashing. None of these measures would have made the aircraft any "safer", if the problem was one of poor stalling characteristics. Several pilots who flew the type mentioned that they had no problems but were careful to keep the airspeed well above stalling point. [16]

Preparing for a night take off R.E8 (night).jpg
Preparing for a night take off

R.E.8s began to arrive at the front in numbers just as the period of German air superiority known as "Bloody April" was taking a heavy toll of all types in the RFC; and early service was not auspicious. On 13 April 1917, six R.E.8s from 59 Squadron were sent on a long range photo reconnaissance mission, missed their intended escorts, and were met by the picked fighter pilots of Jasta 11 , who shot them all down within five minutes. [17]

The casualty rate in R.E.8 squadrons became more sustainable as new Allied fighter types regained air superiority and pilot training and tactics improved. Although never a popular aeroplane, it was reasonably satisfactory for the tasks demanded of it and was even regarded with some affection, gaining the rhyming slang nickname "Harry Tate" (after a popular music hall artist of the time). Some crews flew their slow, cumbersome mounts quite aggressively; the German fighter ace Eduard Ritter von Dostler was shot down by an R.E.8 of 7 Squadron, while 3 Squadron Australian Flying Corps (AFC) was credited with 50 air victories in 12 months of operations. [18] Lts Pithey and Rhodes of 12 Squadron were the most successful R.E.8 crew in air-to-air combat, being credited with twelve victories. [19]

An R.E.8 crew are briefed before a mission R.E.8 (Cockpit area).jpg
An R.E.8 crew are briefed before a mission

Although supplemented by other types, the R.E.8 remained the standard RFC artillery observation, air photography and general short range reconnaissance aircraft for the remainder of the war, equipping 18 RFC squadrons in 1917 and 19 squadrons in 1918. Belgium was the only country other than Britain and the Dominions to operate the R.E.8 during the First World War, receiving 22 in July 1917. At least some of the Belgian examples were fitted with Hispano-Suiza engines, in a SPAD type cowling, rather than the S.E.5a type cowling of the R.E.8a. [10]

It was hoped to be able to replace the R.E.8 with a version of the Bristol Fighter powered by the Sunbeam Arab engine but the combination proved unsuccessful and few "Arab Bristols" were ever built. [20] A few R.E.8 squadrons were issued with one or two standard (Falcon engined) F.2bs in the last weeks of the war. [21] By November 1918, the R.E.8 was regarded as totally obsolete and surviving examples were quickly retired after the Armistice. Nor was the type popular with the private owners who purchased surplus RAF aircraft after the war and no R.E.8s came onto the civil register.

Variants

R.E.8
Standard general purpose aircraft, powered by 140 hp (104 kW) RAF 4a engine.
R.E.8a
Conversion of one R.E.8 with 200 hp (149 kW) Hispano-Suiza engine in a square, S.E.5 (or B.E.12b) type cowling. No production due to shortage of Hispano engines. [22] At least some of the R.E.8s supplied to Belgium were also re-engined with Hispanos – in this case in a cowling resembling that of the later SPADs.
R.E.9
R.E.8 modified with equal-span wings similar to those of the B.E.2c/d and the larger fin and rudder fitted to some R.E.8s at training units. Two were converted in 1917, but they showed no advantage over the standard R.E.8 (climb and manoeuvrability were worse) and no production followed. [22]
R.E.8 F3556 preserved at the Imperial War Museum Duxford RE8 duxford 001.jpg
R.E.8 F3556 preserved at the Imperial War Museum Duxford
Belgian R.E.8 with water-cooled Hispano-Suiza engine in revised cowling RMM Brussel RE8 2.JPG
Belgian R.E.8 with water-cooled Hispano-Suiza engine in revised cowling
Siddeley-Deasy R.T.1
Development of R.E.8 with equal span biplane wings of a new design.

Surviving aircraft

Only two "original" R.E.8s survive from World War One. [1]

The restoration of R.E.8 F3556 at the Imperial War Museum Duxford was completed in 2004. This aircraft, built by Daimler, arrived in France on Armistice Day, still in its original packing case. It is currently displayed suspended from the roof of the AirSpace hangar at Duxford. [23]

The other surviving R.E.8 is a former Aviation Militaire Belge machine preserved at the Brussels Air Museum. It is fitted with the usual Hispano-Suiza engine typical of R.E.8s in Belgian service, in the usual SPAD type cowling and circular frontal radiator. [24]

The Royal Air Force Museum at Hendon has a full size replica R.E.8, which was built by The Vintage Aviator Ltd ( TVAL ) in New Zealand in 2011. It is fitted with a "new build" RAF 4a engine and was successfully test flown at Masterton, NZ, on 1 January 2012, with the registration ZK-TVC. Crated and shipped to England, it was reassembled at The Shuttleworth Collection at Old Warden Airfield in June 2012 and undertook a number of flights painted as 'A3930' of No. 9 Squadron Royal Flying Corps, before being sent by road to Hendon in November 2012. It is now on static display in the Grahame-White Factory. [25]

The Royal Australian Air Force has an airworthy replica R.E.8, built in 2012 and painted in late WW1 era Australian Flying Corps livery. It was previously part of the RAAF Museum collection and as of 2021 is with the Air Force Heritage Squadron.

Operators

Flag of Australia (converted).svg  Australia
Flag of Belgium (civil).svg  Belgium
Flag of Estonia.svg  Estonia
Flag of the Soviet Union.svg  Soviet Union
Flag of the United Kingdom.svg  United Kingdom

Specifications

R.A.F. R.E.8 drawing R.A.F. R.E.8 dwg.jpg
R.A.F. R.E.8 drawing

Data fromThe Royal Aircraft Factory [27]

General characteristics

Performance

Armament

See also

Aircraft of comparable role, configuration, and era

Related lists

Related Research Articles

<span class="mw-page-title-main">Vickers Vimy</span> Type of aircraft

The Vickers Vimy was a British heavy bomber aircraft developed and manufactured by Vickers Limited. Developed during the latter stages of the First World War to equip the Royal Flying Corps (RFC), the Vimy was designed by Rex Pierson, Vickers' chief designer.

<span class="mw-page-title-main">Royal Aircraft Factory B.E.2</span> 1912 military aircraft family by the Royal Aircraft Factory

The Royal Aircraft Factory B.E.2 is a British single-engine tractor two-seat biplane, designed and developed at the Royal Aircraft Factory. Most of the roughly 3,500 built were constructed under contract by private companies, including established aircraft manufacturers and firms new to aircraft construction.

<span class="mw-page-title-main">Bristol F.2 Fighter</span> British fighter aircraft used in World War One

The Bristol F.2 Fighter is a British First World War two-seat biplane fighter and reconnaissance aircraft developed by Frank Barnwell at the British and Colonial Aeroplane Company later known as the Bristol Aeroplane Company. It is often simply called the Bristol Fighter, "Brisfit" or "Biff".

<span class="mw-page-title-main">SPAD S.XIII</span> French WW1 fighter aircraft

The SPAD S.XIII is a French biplane fighter aircraft of the First World War, developed by Société Pour L'Aviation et ses Dérivés (SPAD) from the earlier and highly successful SPAD S.VII.

<span class="mw-page-title-main">SPAD S.VII</span> French WW1 fighter aircraft

The SPAD S.VII was the first of a series of highly successful biplane fighter aircraft produced by Société Pour L'Aviation et ses Dérivés (SPAD) during the First World War. Like its successors, the S.VII was renowned as a sturdy and rugged aircraft with good climbing and diving characteristics. It was also a stable gun platform, although pilots used to the more maneuverable Nieuport fighters found it heavy on the controls. It was flown by a number of the famous aces, such as France's Georges Guynemer, Italy's Francesco Baracca and Australia's Alexander Pentland.

<span class="mw-page-title-main">Royal Aircraft Factory F.E.2</span> Type of aircraft

Between 1911 and 1914, the Royal Aircraft Factory used the F.E.2 designation for three quite different aircraft that shared only a common "Farman" pusher biplane layout.

<span class="mw-page-title-main">Royal Aircraft Factory S.E.5</span> Royal Aircraft Factory aircraft

The Royal Aircraft Factory S.E.5 is a British biplane fighter aircraft of the First World War. It was developed at the Royal Aircraft Factory by a team consisting of Henry Folland, John Kenworthy and Major Frank Goodden. It was one of the fastest aircraft of the war, while being both stable and relatively manoeuvrable. According to aviation author Robert Jackson, the S.E.5 was: "the nimble fighter that has since been described as the 'Spitfire of World War One'".

<span class="mw-page-title-main">Vickers F.B.5</span> Fighter aircraft; first operational purpose-built fighter

The Vickers F.B.5 was a British two-seat pusher military biplane of the First World War. Armed with a single .303 in (7.7 mm) Lewis gun operated by the observer in the front of the nacelle, it was the first aircraft purpose-built for air-to-air combat to see service, making it the world's first operational fighter aircraft.

<span class="mw-page-title-main">Sopwith Dolphin</span> British WW1 biplane fighter aircraft

The Sopwith 5F.1 Dolphin was a British fighter aircraft manufactured by the Sopwith Aviation Company. It was used by the Royal Flying Corps and its successor, the Royal Air Force, during the First World War. The Dolphin entered service on the Western Front in early 1918 and proved to be a formidable fighter. The aircraft was not retained in the postwar inventory and was retired shortly after the war.

<span class="mw-page-title-main">Armstrong Whitworth F.K.8</span> 1916 utility aircraft by Armstrong Whitworth

The Armstrong Whitworth F.K.8 was a British two-seat general-purpose biplane built by Armstrong Whitworth during the First World War. The type served alongside the better known R.E.8 until the end of the war, at which point 694 F.K.8s remained on RAF charge.

<span class="mw-page-title-main">Royal Aircraft Factory B.E.12</span> Type of aircraft

The Royal Aircraft Factory B.E.12 was a British single-seat aeroplane of The First World War designed at the Royal Aircraft Factory. It was essentially a single-seat version of the B.E.2.

<span class="mw-page-title-main">Royal Aircraft Factory F.E.8</span> Type of aircraft

The Royal Aircraft Factory F.E.8 was a British single-seat fighter of the First World War designed at the Royal Aircraft Factory. It could not escape the drag penalty imposed by its tail structure and was no match for the Albatros fighters of late 1916.

<span class="mw-page-title-main">Nieuport 12</span> French WW1 fighter and reconnaissance aircraft

The Nieuport 12 was a French sesquiplane reconnaissance, fighter aircraft and trainer used by France, Russia, Great Britain and the United States during World War I. Later production examples were built as trainers and served widely until the late 1920s.

<span class="mw-page-title-main">Vickers Vampire</span> Type of aircraft

The Vickers F.B.26 Vampire was a British single-seat pusher biplane fighter built by Vickers during the First World War.

<span class="mw-page-title-main">Morane-Saulnier BB</span> Type of aircraft

The Morane-Saulnier BB was a military observation aircraft produced in France during World War I for use by Britain's Royal Flying Corps. It was a conventional single-bay biplane design with seating for the pilot and observer in tandem, open cockpits. The original order called for 150 aircraft powered by 110-hp Le Rhône 9J rotary engines, but shortages meant that most of the 94 aircraft eventually built were delivered with 80 hp Le Rhône 9C rotaries instead. A water-cooled Hispano-Suiza 8A engine was trialled as an alternative in the Type BH, but this remained experimental only. A production licence was sold to the Spanish company Compañía Española de Construcciones Aeronáuticas (CECA), which built twelve fitted with Hispano-Suiza engines in 1916.

<span class="mw-page-title-main">Royal Aircraft Factory F.E.9</span> Type of aircraft

The Royal Aircraft Factory F.E.9 was a prototype British two-seat fighter-reconnaissance aircraft of the First World War. A single-engined pusher biplane of 1917, the F.E.9 had poor performance and handling, and only three were built.

<span class="mw-page-title-main">Royal Aircraft Factory N.E.1</span> Type of aircraft

The Royal Aircraft Factory N.E.1 was a prototype British night fighter of the First World War. A single-engined pusher biplane, it was a development of the Royal Aircraft Factory's earlier F.E.9 fighter, but was not successful, only six being built.

<span class="mw-page-title-main">Vickers F.B.16</span> Type of aircraft

The Vickers F.B.16 was a British single-seat fighter aircraft of the First World War. It was originally designed to be powered by an experimental radial engine, development of which was abandoned. When re-engined with more powerful and reliable water-cooled V-8 engines, the F.B.16 demonstrated good performance, but only a few prototypes were built, the type not entering service.

The Vickers F.B.24 was a British two-seat fighter aircraft of the First World War. Only a few prototypes were built, as, although it had good performance, the Bristol F.2 Fighter was preferred.

<span class="mw-page-title-main">Vickers F.B.25</span> Type of aircraft

The Vickers F.B.25 was a British two-seat night fighter prototype of World War I designed to attack enemy airships. Completed in 1917, it failed in its official flight tests that year and no order for production resulted.

References

Citations

  1. 1 2 Bruce 1966, p. 10.
  2. ↑ Hare 1990, p. 258.
  3. 1 2 3 4 5 6 Bruce 1966, p. 3.
  4. 1 2 Cheesman 1962, pp. 50–56.
  5. ↑ Mason 1994, p. 61.
  6. 1 2 Bruce 1966, pp. 4–5.
  7. ↑ Bruce 1954, p. 577.
  8. 1 2 3 4 Bruce 1966, p. 5.
  9. ↑ Hare 1990, pp. 259–260.
  10. 1 2 Bruce 1966, p. 9.
  11. ↑ Hare 1990, p. 259.
  12. ↑ Bruce 1966, p. 6.
  13. 1 2 Hare 1990, p. 261.
  14. ↑ Bruce 1966, pp. 5–6.
  15. ↑ Bruce 1966, p. 12.
  16. ↑ Rowe 2001 pp. 64–70
  17. ↑ Bruce 1954, pp. 577–578.
  18. ↑ Schaedel 1972, p. 23.
  19. ↑ Franks (et al.) 1997 pp. 72–73
  20. ↑ Cheesman 1962, p.62
  21. ↑ Molkentin 2010, caption to plate 28 (between pp. 184–185)
  22. 1 2 Hare 1990, p. 267.
  23. ↑ "Royal Aircraft Factory RE.8." Imperial War Museum, Retrieved: 28 December 2017.
  24. ↑ "Brussels Air Museum." Archived 25 December 2017 at the Wayback Machine sbap.be, Retrieved: 28 December 2017.
  25. ↑ "Royal Aircraft Factory R.E.8." RAF Museum, Retrieved: 28 December 2017.
  26. ↑ Gerdessen 1982, p. 76.
  27. ↑ Hare 1990, pp. 266–267.
  28. ↑ Bruce 1954, p. 581.

Bibliography

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.