The Austin FX3 is a taxicab that was sold in the United Kingdom by the Austin from 1948 to 1958. It was designed to comply with the Metropolitan PoliceConditions of Fitness for London taxicabs, but was also used in other towns and cities in the UK. It was commissioned from Austin by taxi dealers Mann & Overton and built by Carbodies of Coventry on a chassis supplied by Austin.
The first prototype, the FX had a 1.8-litre sidevalve engine that proved inadequate for the job. The second prototype, the FX2 had a 1.8-litre petrol engine, but this was replaced by the third version, the FX3, which had a 2.2-litre ohv petrol engine. Fitted with an all-steel body from Carbodies the FX3 was registered as JXN 842, and it and the FX2 (registered as JXN 841) went on test in the summer of 1948. It was announced at the Commercial Motor Exhibition in the following November and went into full production in 1949.[1]
Following on from previous designs of London taxi, the FX3 had a traditional 3-door body, with an open luggage platform rather than a front passenger seat beside the driver. The FX3 was fitted with mechanical brakes, with rod operation, beam axles on leaf springs and a built-in Jackall hydraulic jacking system. Like all London taxis, it has a tight turning circle of 25ft (7.6m) diameter, as required by the Conditions of Fitness.[2]
The petrol engine proved too expensive to run and a conversion to a Standard diesel engine was offered by taxi and bus proprietors Birch Brothers of Kentish Town.[3] A 3-litre Perkins engine was also offered and these, as well as pressure for Mann & Overton prompted the Austin Motor Company to develop their own diesel engine.[4] This appeared in 1956 and quickly became the most popular choice in the FX3. The FX3's manual transmission has four forward speeds plus reverse, with synchromesh on all but first gear. In 1957-1958 a series of automatic transmission test vehicles were manufactured, of which only two are known to survive.
Outside London, cab operators in major UK cities like Manchester, Birmingham, Glasgow and Liverpool ran FX3s, either bought new or when they were retired from service in the capital. Examples of four-door FX3s were known to run in Manchester, where, in common with every other UK local authority outside London [5] different taxi licensing regulations were enforced. Several FX3s were exported to Madrid, Spain and proved successful. Attempts to sell them to the United States were a failure.
Austin's standard hire car body FL1
A Hire Car version, the FL1 was also made, which had four full doors, a bench front seat, column gear-change and an umbrella-type handbrake handle. The two occasional seats faced forward. A 'driveaway' chassis-cab was also supplied to outside coachbuilders. Several shooting brake ('woodie' ) bodies were made, as well as newspaper vans for the three London evening papers, the Star, News and Standard. A number of hearse bodies were also mounted on FL1 chassis by such coachbuilders as Simpson and Slater, Alpe and Saunders, Arthur Mulliner and Woodall Nicholson.[6] Undoubtedly the most remarkable body built on an FX3 chassis belonged to Armenian oil magnate Nubar Gulbenkian. Built by London coachbuilders FLM Panelcraft, it was an open-drive town car, with carriage lamps and wickerwork decoration on the body sides. It was powered by a Ford six cylinder engine.[7]
The FX3 was a popular model. Out of a combined production total of 12,435 [8] FX3 and FL1 models, 7,267[9] were licensed in London between 1948 and the end of production in 1958.
The FX3 was replaced in 1958 by the Austin FX4, but continued in use in London until 1968. Many other examples ran for longer outside London. In turn, the FX4 ceased production in 1997 and was replaced by the TX series.
The Austin FX3 is still sought after by collectors and enthusiasts of vintage London Transport. Several Austin FX3s have been shipped to the United States of America and to continental Europe by collectors, hobbyists and for use as advertisement icons.
Carbodies became part of LTI (London Taxis International) and from 2010 is known as The London Taxi Company.
The Austin Princess is a series of large luxury cars that were made by Austin and its subsidiary Vanden Plas from 1947 to 1968. The cars were also marketed under the Princess and Vanden Plas marque names.
A hackney or hackney carriage is a carriage or car for hire. A hackney of a more expensive or high class was called a remise. A symbol of London and Britain, the black taxi is a common sight on the streets of the UK. The hackney carriages carry a roof sign TAXI that can be illuminated at night to indicate their availability for passengers.
Manganese Bronze Holdings plc (MBH) was the holding company of LTI Limited. The firm's sole business in its final years as a company was London black taxicab manufacturing through the LTI subsidiary.
A coachbuilder or body-maker is someone who manufactures bodies for passenger-carrying vehicles. Coachwork is the body of an automobile, bus, horse-drawn carriage, or railway carriage. The word "coach" was derived from the Hungarian town of Kocs.
Wolseley Motors Limited was a British motor vehicle manufacturer founded in early 1901 by the Vickers Armaments in conjunction with Herbert Austin. It initially made a full range, topped by large luxury cars, and dominated the market in the Edwardian era. The Vickers brothers died and, without their guidance, Wolseley expanded rapidly after the war, manufacturing 12,000 cars in 1921, and remained the biggest motor manufacturer in Britain.
The Austin FX4 is a hackney carriage that was produced from 1958 until 1997. It was sold by Austin from 1958 until 1982, when Carbodies, who had been producing the FX4 for Austin, took over the intellectual rights to the car. Carbodies continued production until 1984, when London Taxis International took over rights and continued producing it until 1997. In all, more than 75,000 FX4s were built. The FX4 also featured as a playable car in the 2018 video game Forza Horizon 4.
The Rolls-Royce Phantom III was the final large pre-war Rolls-Royce. Introduced in 1936, it replaced the Phantom II and it was the only V12 Rolls-Royce until the 1998 introduction of the Silver Seraph. 727 V12 Phantom III chassis were constructed from 1936 to 1939, and many have survived. Although chassis production ceased in 1939, cars were still being bodied and delivered in 1940 and 1941. The last car, though the rolling chassis was completed in 1941, was not delivered with a body to its owner until 1947. The Phantom III was the last car that Henry Royce worked on – he died, aged 70, a year into the Phantom III's development.
The London Taxi Company was a taxi design and manufacturing company based in Coventry, England. It formerly traded as London Taxis International and Carbodies.
The LTI TX1 is a Hackney carriage introduced by London Taxis International in 1997 and designed to replace the ageing Austin FX4. It was designed by British product designer Kenneth Grange.
The Nuffield Oxford Taxi, initially produced as the Wolseley Oxford Taxicab was the first new taxicab designed to comply with the Metropolitan Police Conditions of Fitness for London taxicabs to be launched on the British market after the end of the Second World War.
Hooper & Co. was a British coachbuilding business for many years based in Westminster London. From 1805 to 1959 it was a notably successful maker, to special order, of luxury carriages, both horse-drawn and motor-powered.
The MCW Metrocab is a taxicab that was manufactured between 1987 and 2000 and as the Metrocab TTT from 2000 to 2006. It was designed and originally produced by the British vehicle manufacturing company Metro Cammell Weymann (MCW), with ownership passing to Reliant in 1989, Hooper in 1991 and finally Kamkorp in 2000.
The TX4 is a purpose-built taxicab manufactured by The London Taxi Company, a subsidiary of Geely Automobile of China. From 2007 until their liquidation in 2013 it was manufactured by LTI. It is the latest in a long line of purpose-built taxis produced by The London Taxi Company and various predecessor entities. The design has evolved via several mutations from the Austin FX3 of the 1950s. TX4's immediate predecessor is the TXII.
Engines used by the British company Land Rover in its 4×4 vehicles have included four-cylinder petrol engines, and four- and five-cylinder diesel engines. Straight-six cylinder engines have been used for Land Rover vehicles built under licence. Land Rover has also used various four-cylinder, V8, and V6 engines developed by other companies, but this article deals only with engines developed specifically for Land Rover vehicles.
The Austin London Taxicab used a modified Austin Heavy Twelve-Four chassis clothed with new bodies designed by London's largest taxicab retailer and dealer Mann & Overton, and made for them by London coachbuilders.
Mann & Overton Limited owned and operated a motor vehicle dealers business previously known as Mann & Overton's and established 14 May 1901 which came to specialise in the supply and financing of London taxicabs, first Unic then Austin Taxicabs, eventually holding the concession for the Austin taxicab chassis for the whole of the Metropolitan Police Area of London.
W & G Du Cros Limited also well-known as W & G was a business established in 1901 as a motor importers and dealership by Harvey Du Cros, founder of the pneumatic tyre industry also founder and head of the Dunlop Rubber Company and a major investor in businesses connected to the automobile. It grew into a major taxicab business and car and commercial motor-body builder which manufactured it own brand lorries and passenger vehicles.
William Vincent Ltd., often known as Vincent of Reading, was a British coachbuilder founded in 1805 making carriages but in 1899 they made their first car body and later made bodies for commercial vehicles.
New Avon was a British vehicle coachbuilder. The company, based in Warwick, was started when a Ben Tilton and a Captain Philips trading as Avon Coachworks went into business in 1919 to make bodywork for cars. Following a change of ownership and financial reconstruction it became New Avon in 1922.
The Austin D and K series engines are a straight-six engine made by the British Austin Motor Company between 1939 and 1968. It was developed initially for the lorry market; but was used in a number of automobiles in its later life. It was an overhead valve non-crossflow cylinder head design. Both block and head were made out of cast iron. All engines had a forged four main bearing crankshaft.
References
Wikimedia Commons has media related to Austin FX3.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
