Blocked isocyanates

Last updated

Blocked isocyanates are organic compounds that have their isocyanate functionality chemically blocked to control reactivity. [1] They are the product of an isocyanate moiety (nearly always a di-isocyanate) and a suitable blocking agent. It may also be a polyurethane prepolymer that is NCO terminated but this functionality has also been chemically reacted with a blocking agent. They are usually used in polyurethane applications but not always. [2] They are extensively used in industrial applications such as coatings, sealants and adhesives. [3] [4] [5]

Contents

Overview

A blocked isocyanate can be added to materials that would normally react with the isocyanate such as polyols. They do not react at normal ambient room temperature. A formulation containing a blocked isocyanate is a single component material (and thus usually considered more convenient) but reacts like a two-component product but will not react until heated to the temperature required for activation which varies depending on the blocking agent. [6] The shelf lives when stored at ambient temperature have been reported as good. [7] On heating up to the activation temperature, cure can be as short as 20 minutes depending on the blocking agent and other formulation parameters.

Blocked isocyanates are particularly useful in products with a dual cure mechanisms. As an example, Ultraviolet light initiates the polymerization of an acrylate based polymer that contains hydroxy groups on the polymer backbone. The system would also contain an isocyanate blocked with a malonate. This is now a one-component system. When heat is applied, the polymerization is initiated. Higher temperatures then unblock the isocyanate, allowing the cure and crosslinking of the urethane.

Blocking agents

A number of blocking agents maybe employed but a common one is Methylethyl ketone oxime (MEKO). Caprolactam is also used. [8]

When blocked, there is no isocyanate (NCO) functionality, so it is much easier to disperse the species in water if the desire is to produce waterborne resins. [9] [10] One of the key reasons different blocking agents are used apart from chemical properties is that they unblock at different temperatures. MEKO has a fairly low unblocking temperature and is thus in fairly common usage. A mixture of blocking agents maybe used to optimize properties. [11]

Unblocking temperatures

Different blocking agents for isocyanates have different unblocking temperatures. [12]

Catalysts

Catalysts also have a role in the unblocking of blocked isocyanates. [15] As with regular isocyanates organometallic compounds and tertiary amines may lower the unblocking temperature. Tin compounds, such as dibutyltin dilaurate, dibutyltin diacetate and other metal compounds are effective deblocking catalysts.

Uses

Apart from uses in coatings and adhesives they are also used to enhance the performance of polyester tire cord. [16] Other uses include Powder coatings, Coil Coatings, Cationic Electrocoating and primers. [17] Blocked isocyanates have also been used in tertiary oilfield recovery techniques. A blocked isocyanate is pumped into the rock/geological formation and then an organic compound with an active hydrogen is also pumped down. The result is a polymeric gel assisting with oil recovery. [18] The use of sodium bisulfite as a blocking agent has also allowed them to be used in waterborne resins such as PUDs. [19] Similarly, vanillin maybe used as an isocyanate blocker and is actively being researched. It is then used in single component waterborne coatings. [20]

See also

Related Research Articles

<span class="mw-page-title-main">Polyurethane</span> Polymer composed of a chain of organic units joined by carbamate (urethane) links

Polyurethane refers to a class of polymers composed of organic units joined by carbamate (urethane) links. In contrast to other common polymers such as polyethylene and polystyrene, polyurethane is produced from a wide range of starting materials. This chemical variety produces polyurethanes with different chemical structures leading to many different applications. These include rigid and flexible foams, and coatings, adhesives, electrical potting compounds, and fibers such as spandex and polyurethane laminate (PUL). Foams are the largest application accounting for 67% of all polyurethane produced in 2016.

<span class="mw-page-title-main">Isocyanate</span> Chemical group (–N=C=O)

In organic chemistry, isocyanate is the functional group with the formula R−N=C=O. Organic compounds that contain an isocyanate group are referred to as isocyanates. An organic compound with two isocyanate groups is known as a diisocyanate. Diisocyanates are manufactured for the production of polyurethanes, a class of polymers.

<span class="mw-page-title-main">Thermosetting polymer</span> Polymer obtained by irreversibly hardening (curing) a resin

In materials science, a thermosetting polymer, often called a thermoset, is a polymer that is obtained by irreversibly hardening ("curing") a soft solid or viscous liquid prepolymer (resin). Curing is induced by heat or suitable radiation and may be promoted by high pressure, or mixing with a catalyst. Heat is not necessarily applied externally, but is often generated by the reaction of the resin with a curing agent. Curing results in chemical reactions that create extensive cross-linking between polymer chains to produce an infusible and insoluble polymer network.

<span class="mw-page-title-main">Oxazolidine</span> Chemical compound

Oxazolidine is a five-membered ring heterocycle with the formula (CH2)3(NH)O.The O atom and NH groups are not mutually bonded, in contrast to isoxazolidine. Oxazolidines are derivatives of the parent oxazolidine owing to the presence of substituents on carbon and/or nitrogen. Oxazolines are unsaturated analogues of oxazolidines.

<span class="mw-page-title-main">Polyurea</span> Class of elastomers

Polyurea is a type of elastomer that is derived from the reaction product of an isocyanate component and an amine component. The isocyanate can be aromatic or aliphatic in nature. It can be monomer, polymer, or any variant reaction of isocyanates, quasi-prepolymer or a prepolymer. The prepolymer, or quasi-prepolymer, can be made of an amine-terminated polymer resin, or a hydroxyl-terminated polymer resin.

In organic chemistry, a polyol is an organic compound containing multiple hydroxyl groups. The term "polyol" can have slightly different meanings depending on whether it is used in food science or polymer chemistry. Polyols containing two, three and four hydroxyl groups are diols, triols, and tetrols, respectively.

<span class="mw-page-title-main">Methylene diphenyl diisocyanate</span> Aromatic diisocyanate

Methylene diphenyl diisocyanate (MDI) is an aromatic diisocyanate. Three isomers are common, varying by the positions of the isocyanate groups around the rings: 2,2′-MDI, 2,4′-MDI, and 4,4′-MDI. The 4,4′ isomer is most widely used, and is also known as 4,4′-diphenylmethane diisocyanate. This isomer is also known as Pure MDI. MDI reacts with polyols in the manufacture of polyurethane. It is the most produced diisocyanate, accounting for 61.3% of the global market in the year 2000.

<span class="mw-page-title-main">Polypropylene glycol</span> Chemical compound

Polypropylene glycol or polypropylene oxide is the polymer of propylene glycol. Chemically it is a polyether, and, more generally speaking, it's a polyalkylene glycol (PAG) H S Code 3907.2000. The term polypropylene glycol or PPG is reserved for polymer of low- to medium-range molar mass when the nature of the end-group, which is usually a hydroxyl group, still matters. The term "oxide" is used for high-molar-mass polymer when end-groups no longer affect polymer properties. Between 60 and 70% of propylene oxide is converted to polyether polyols by the process called alkoxylation.

<span class="mw-page-title-main">Polyisocyanurate</span> Type of plastic typically used for thermal insulation

Polyisocyanurate, also referred to as PIR, polyiso, or ISO, is a thermoset plastic typically produced as a foam and used as rigid thermal insulation. The starting materials are similar to those used in polyurethane (PUR) except that the proportion of methylene diphenyl diisocyanate (MDI) is higher and a polyester-derived polyol is used in the reaction instead of a polyether polyol. The resulting chemical structure is significantly different, with the isocyanate groups on the MDI trimerising to form isocyanurate groups which the polyols link together, giving a complex polymeric structure.

<span class="mw-page-title-main">Hexamethylene diisocyanate</span> Chemical compound

Hexamethylene diisocyanate (HDI) is the organic compound with the formula (CH2)6(NCO)2. It is classified as an diisocyanate. It is a colorless liquid. It has sometimes been called HMDI but this not usually done to avoid confusion with Hydrogenated MDI.

<span class="mw-page-title-main">Hexamethylenediamine</span> Chemical compound

Hexamethylenediamine is the organic compound with the formula H2N(CH2)6NH2. The molecule is a diamine, consisting of a hexamethylene hydrocarbon chain terminated with amine functional groups. The colorless solid (yellowish for some commercial samples) has a strong amine odor. About 1 billion kilograms are produced annually.

A thermoset polymer matrix is a synthetic polymer reinforcement where polymers act as binder or matrix to secure in place incorporated particulates, fibres or other reinforcements. They were first developed for structural applications, such as glass-reinforced plastic radar domes on aircraft and graphite-epoxy payload bay doors on the Space Shuttle.

In polymer chemistry, the term prepolymer or pre-polymer, refers to a monomer or system of monomers that have been reacted to an intermediate-molecular mass state. This material is capable of further polymerization by reactive groups to a fully cured, high-molecular-mass state. As such, mixtures of reactive polymers with un-reacted monomers may also be referred to as pre-polymers. The term "pre-polymer" and "polymer precursor" may be interchanged.

Polyaspartic ester chemistry was first introduced in the early 1990s making it a relatively new technology. The patents were issued to Bayer in Germany and Miles Corporation in the United States. It utilizes the aza-Michael addition reaction. These products are then used in coatings, adhesives, sealants and elastomers. Pure polyurea reacts extremely quickly making them almost unusable without plural component spray equipment. Polyaspartic technology utilizes a partially blocked amine to react more slowly with the isocyanates and thus produce a modified polyurea. The amine/diamine or even triamine functional coreactant for aliphatic polyisocyanate is typically reacted with a maleate. Polyaspartic esters (PAE) initially found use in conventional solvent-borne two-component polyurethane coatings.

Moisture-cure polyurethanes -- or polyurethane prepolymer -- are isocyanate-terminated prepolymers that are formulated to cure with ambient water. Cured PURs are segmented copolymer polyurethane-ureas exhibiting microphase-separated morphologies. One phase is derived from a typically flexible polyol that is generally referred to as the “soft phase”. Likewise the corresponding “hard phase” is born from the di- or polyisocyanates that through water reaction produce a highly crosslinked material with softening temperature well above room temperature.

Polyurethane Dispersion, or PUD, is understood to be a polyurethane polymer resin dispersed in water, rather than a solvent, although some cosolvent maybe used. Its manufacture involves the synthesis of polyurethanes having carboxylic acid functionality or nonionic hydrophiles like PEG incorporated into, or pendant from, the polymer backbone. Two component polyurethane dispersions are also available.

<span class="mw-page-title-main">Tetramethylxylylene diisocyanate</span> Chemical compound

Tetramethylxylylene diisocyanate (TMXDI) is an organic compound with the formula C6H4(CMe2NCO)2 (Me = CH3). Introduced in the 1980s by American Cyanamid, the molecule features two isocyanate groups. TMXDI is generally classified as an aliphatic isocyanate, which are generally more UV stable than their aromatic counterparts.

<span class="mw-page-title-main">Dimethylolpropionic acid</span> Organic compound with one carboxyl and two hydroxyl groups

Dimethylolpropionic acid (DMPA) is a chemical compound that has the full IUPAC name of 2,2-bis(hydroxymethyl)propionic acid and is an organic compound with one carboxyl and two hydroxy groups. It has the CAS Registry Number of 4767-03-7.

Waterborne resins are sometimes called water-based resins. They are resins or polymeric resins that use water as the carrying medium as opposed to solvent or solvent-less. Resins are used in the production of coatings, adhesives, sealants, elastomers and composite materials. When the phrase waterborne resin is used, it usually describes all resins which have water as the main carrying solvent. The resin could be water-soluble, water reducible or water dispersed.

Hydrogenated MDI (H12MDI or 4,4′-diisocyanato dicyclohexylmethane) is an organic compound in the class known as isocyanates. More specifically, it is an aliphatic diisocyanate. It is a water white liquid at room temperature and is manufactured in relatively small quantities. It is also known as 4,4'-methylenedi(cyclohexyl isocyanate) or methylene bis(4-cyclohexylisocyanate) and has the formula CH2[(C6H10)NCO]2.

References

  1. ↑ Wicks, Zeno W. (1975-03-01). "Blocked isocyanates". Progress in Organic Coatings. 3 (1): 73–99. doi:10.1016/0300-9440(75)80002-6. ISSN   0300-9440.
  2. ↑ S.Rolph, Marianne; J.Markowska, Anna L.; N.Warriner, Colin; K.O'Reilly, Rachel (2016). "Blocked isocyanates: from analytical and experimental considerations to non-polyurethane applications". Polymer Chemistry. 7 (48): 7351–7364. doi: 10.1039/C6PY01776B .
  3. ↑ "Blocked Isocyanates: OEM -Industrial Coatings" (PDF). Leeson Polyurethanes. Archived (PDF) from the original on 2021-08-25.
  4. ↑ Jones, R. (2008-03-01). "Cross-linking organic coatings with blocked isocyanates". Transactions of the IMF. 86 (2): 75–79. doi:10.1179/174591908X264464. ISSN   0020-2967. S2CID   98308996.
  5. ↑ Subramani, S.; Park, Young-Jun; Cheong, In-Woo; Kim, Jung-Hyun (2004). "Polyurethane ionomer dispersions from a blocked aromatic-diisocyanate prepolymer". Polymer International. 53 (8): 1145–1152. doi:10.1002/pi.1516. ISSN   1097-0126.
  6. ↑ Wicks, Douglas A.; Wicks, Zeno W. (2001-11-01). "Multistep chemistry in thin films; the challenges of blocked isocyanates". Progress in Organic Coatings. 43 (1–3): 131–140. doi:10.1016/S0300-9440(01)00188-6. ISSN   0300-9440.
  7. ↑ S.Rolph, Marianne; J.Markowska, AnnaL.; N.Warriner, Colin; K.O'Reilly, Rachel (2016). "Blocked isocyanates: from analytical and experimental considerations to non-polyurethane applications". Polymer Chemistry. 7 (48): 7351–7364. doi: 10.1039/C6PY01776B .
  8. ↑ "Blocked Isocyanate - an overview | ScienceDirect Topics". www.sciencedirect.com. Retrieved 2021-08-25.
  9. ↑ "Caprolactam And Phenol Blocked MDI Adhesion Promoter 45% Dispersion of Blocked Isocyanate Caprolactam And Phenol". Gloriaful Industry Co., Limited. Retrieved 2021-08-25.
  10. ↑ "Development Of Superior Blocked High-Performance Prepolymers Utilizing Low Monomer Technology". Coatings World. Retrieved 2021-08-25.
  11. ↑ Lee, Jung Min; Subramani, Sankaraiah; Lee, Young Soo; Kim, Jung Hyun (2005-10-01). "Thermal decomposition behavior of blocked diisocyanates derived from mixture of blocking agents". Macromolecular Research. 13 (5): 427–434. doi:10.1007/BF03218476. ISSN   2092-7673. S2CID   53052466.
  12. ↑ "Blocked Isocyanates and Their Usage in Plastic Coatings Applications". www.pcimag.com. Retrieved 2021-09-09.
  13. ↑ Zhou, Zhengfa; Lv, Hongxiang; Wang, Xiaowen; Ren, Fengmei; Xu, Weibing (2013). "Deblocking of the water-soluble isophorone diisocyanate blocked by sodium bisulfite and its application". Journal of Applied Polymer Science. 128 (1): 597–599. doi:10.1002/app.38238. ISSN   1097-4628.
  14. ↑ Kostyk, Barry W.; Wicks, Zeno W. (1979). "Malonic ester-blocked aliphatic isocyanates". Journal of Polymer Science: Polymer Chemistry Edition. 17 (8): 2423–2428. Bibcode:1979JPoSA..17.2423K. doi:10.1002/pol.1979.170170814. ISSN   1542-9369.
  15. ↑ Blank, Werner. "Advances in Catalysis for Organic Coatings" (PDF). King Industries. Archived (PDF) from the original on 2003-03-21.
  16. ↑ Schroeter, A. (2004). "Enhance the treatment of Polyester cord by using a combination of phenolic - and Caprolactam-blocked Isocyanates". Tire Technology International. ISSN   0969-7217.
  17. ↑ Blank, Werner, J. "Catalysis of blocked isocyanates with non tin catalysts" (PDF). King Industries. Archived (PDF) from the original on 2003-03-21.
  18. ↑ Fink, Johannes Karl (2015). "18.6". Petroleum Engineer's Guide to Oilfield Chemicals and Fluids, second edition (2 ed.). Elsevier. pp. 653–693. doi:10.1016/c2015-0-00518-4. ISBN   978-0-12-803734-8.
  19. ↑ Zhou, Zhengfa; Lv, Hongxiang; Wang, Xiaowen; Ren, Fengmei; Xu, Weibing (2013). "Deblocking of the water-soluble isophorone diisocyanate blocked by sodium bisulfite and its application". Journal of Applied Polymer Science. 128 (1): 597–599. doi:10.1002/app.38238. ISSN   1097-4628.
  20. ↑ Knospe, Philipp; Reichmann, René; Gutmann, Jochen S.; Dornbusch, Michael (2023-03-01). "Vanillin as low-temperature isocyanate-blocking agent and its use in one-component aqueous coatings". Journal of Coatings Technology and Research. 20 (2): 501–520. doi:10.1007/s11998-022-00696-w. ISSN   1935-3804. S2CID   254358393.

Further reading

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.