CAT 15

Last updated
Vittoria
Role Primary glider
National origin Italy
ManufacturerConstruzioni Aeronautiche Taliedo (CAT)
First flight1938
Number built1

The CAT 15 was a single-seat primary glider built in Italy just before the Second World War. Only one was constructed.

Contents

Development

Like many primary gliders of the 1930s, the CAT 15 was an attempt to develop Alexander Lippisch's Zögling. One improvement was the pilot's environment, now seated in an open cockpit within a short fuselage nacelle rather than entirely exposed on a fuselage beam. Earlier Zögling variants like the SG-38 had also included a nacelle [1] but not the CAT 15's cleaner strut braced wing which dispensed with many flying wires. The glider was designed and built at the Construzioni Aeronautiche Taliedo (CAT) under the supervision of Ettore Cattaneo. It was intended to take novice pilots through to their B certificate. [2]

The CAT 15 was a high-wing monoplane, with its two spar wing supported centrally on the fuselage girder and braced on each side from the spars at about mid span to the lower fuselage with a V-form steel faired strut. The wing, mounted with slight dihedral, had constant chord and blunt tips. [2] It had an aspect ratio of 7.8, noticeably higher than the Zögling's 6.7. [1] [2]

Its flat, wooden girder fuselage was very similar to that of the Zögling, with an upper and lower horizontal pair of beams and six diagonal and vertical cross braces. Since the CAT 15's wing was rigidly braced it did not need the above wing pylon which anchored the flying wires of the Zögling. The nacelle was a wooden structure with ovoid cross-section and fabric covering which extended aft just beyond the wing trailing edge. The rear of the girder was braced laterally with a pair of steel wires to the wings. The empennage of the CAT 15 was very similar to that of the Zögling, with a triangular tailplane mounted on the upper beam of the girder carrying rectangular elevators with a large cut-out to allow movement of the near-rectangular, deep, balanced rudder. The glider landed on a sprung skid reaching from the nose to the trailing edge. [2]

Specifications

Data from Pedrielli (2011) p.213 [2]

General characteristics

Performance


Related Research Articles

The Horikawa H-22B-3 is a simple, open frame, two seat primary trainer glider designed and built in Japan in the 1950s.

The Bonomi BS.4 Basettino was a primary glider designed and built in Italy in the 1930s.

Bonomi BS.7 Allievo Italia

The Bonomi BS.7 Allievo Italia was a single seat, primary glider designed and built in Italy in the 1920s.

The Bonomi BS.8 Biancone was a single-seat training glider designed and built in Italy in the 1930s. It was developed from the Bonomi BS.7 Allievo Italia primary glider.

The Bonomi BS.11 Milano and BS.12 Roma were primary gliders designed and built in Italy in the 1930s. Only about six were produced.

The Bonomi BS.16 Allievo Bonomi was a single seat primary glider, designed and built in Italy in 1930 and widely used by flying clubs.

The Bonomi BS.24 Biposto Rome was an Italian dual control trainer designed for club use. Six were built in the mid-1930s.

Piana Canova PC.100

The Piana Canova PC.100 was a primary glider designed and built in Italy in the 1930s. It had many of the characteristics of these simple aircraft but differed greatly in using a wing of rhomboidal plan. Only one was built.

The Pagliani Vittoria was a single-seat glider built in Italy during Second World War. Only one was constructed.

The Sala N1 or N1 Sala was a single-seat,18 m span competition glider built in Italy in 1937. Only one was constructed.

The Teichfuss Tenax was an Italian, one-off, single seat glider, designed and built by Luigi Treichfuss in 1926 and influenced by German developments.

The Teichfuss LT.12 Biposto was an Italian tandem seat primary glider designed by Luigi Teichfuss and flown in 1933.

The Teichfuss Grifo was an Italian training glider designed by Luigi Teichfuss and flown in 1934. It was built in small numbers.

The Teichfuss Cicogna was an Italian tailless single-seat motor glider designed by Luigi Teichfuss and flown in 1936.

The Teichfuss Astore was an Italian Intermediate single-seat trainer glider designed by Luigi Teichfuss and flown in 1936. Two were built.

The Teichfuss Balilla was an Italian single seat primary glider, designed by Luigi Teichfuss and flown in 1939.

The Teichfuss Allievo Pavullo was an Italian single seat open frame primary glider, designed by Luigi Teichfuss of Pavullo and first flown in 1940. It was sold in two versions, strut and cable braced. A single two seat variant was also built.

The CAT 28BP was an Italian development of the licence built Dittmar Condor II into a high performance tandem two seat glider. Built in 1938, it anticipated the post-war, two seat Dittmar Condor IV and held the Italian national distance record for many years.

Jacobs Hols der Teufel

The Jacobs Hols der Teufel was a single seat trainer glider produced in complete and plan forms in Germany from 1928. It was built and used worldwide.

The MSrE M-20 was an Hungarian primary glider with a better performance than the first generation of such aircraft. One of its designers was Ernő Rubik and the MSrE M-20 was his first major contribution. Only one was built.

References

  1. 1 2 Simons, Martin (2006). Sailplanes 1920-1945 (2nd revised ed.). Königswinter: EQIP Werbung & Verlag GmbH. pp. 40–1, 47–9. ISBN   3 9806773 4 6.
  2. 1 2 3 4 5 Pedrielli, Vincenzo; Camastra, Francesco (2011). Italian Vintage Sailplanes. Königswinter: EQIP Werbung & Verlag GmbH. pp. 212–3. ISBN   9783980883894.
  3. ↑ "Notes on the Situation of Gliding in Italy". The Sailplane. 18 (5): 107–8. May 1950.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.