Carbon nanotube supported catalyst

Last updated
Scanning transmission X-ray microscopy image of pod-like carbon nanotube decorated with Fe nanoparticles (red). Fe-decorated carbon nanotube.jpg
Scanning transmission X-ray microscopy image of pod-like carbon nanotube decorated with Fe nanoparticles (red).

Carbon nanotube supported catalyst is a novel supported catalyst, using carbon nanotubes as the support instead of the conventional alumina or silicon support. The exceptional physical properties of carbon nanotubes (CNTs) such as large specific surface areas, excellent electron conductivity incorporated with the good chemical inertness, and relatively high oxidation stability makes it a promising support material for heterogeneous catalysis. [2]

Contents

The catalyst is a substance, usually used in small amounts relative to the reactants, that increases the rate of a chemical reaction without itself undergoing any permanent chemical change. [3] One or more kinds of catalysts can be loaded on another material with a high surface area, which serves as the support, to form a supported catalyst as a whole system. In a supported catalyst system, the significance of using the support are to increase the dispersion of the active phases, to have a better control of the porous structure, to improve mechanical strength, to prevent sintering and to assist catalysis. [4] There is a wide spectrum of supports ranging from conventional and most commonly alumina to novel various kinds of activated carbon. Synthesis methods and functions vary greatly due to different kinds of support and catalytic materials.

The challenge in making a supported nanoparticulate catalyst is to avoid agglomeration. This can be achieved by using a poly-functional anchoring agent, and drying under a relatively low temperature. Relative research are deposition of palladium and platinum particles on activated carbon, using a poly-acrylate anchor. [5] To unveil more molecular details of the extensive interactions between precursors and supports in an aqueous environment, studies of adsorption and precipitation chemistry must be taken into account. Progress is being made in the use of chemical vapor deposition for the synthesis of supported catalysts. Combinatorial techniques have seen their contributions to solid catalyst synthesis.

Background

Catalyst supports and supported catalysts

Catalysts are widely used in various chemical reactions. The activity, stability, selectivity, and regeneration ability are the most important properties to be considered in catalyst design.

The catalyst supports can improve specific properties such as mechanical strength, distribution, stability, catalytical reactivity and selectivity of catalysts. The definition of the support is broad: the shape of support varies, including granular, powdered, colloidal, coprecipitated, extruded, pelleted, spherical, wires, honeycombs, and skeletal supports. Catalyst supports can be either inert or active in reactions. The ensemble of the catalyst and its support can be regarded as an entirety: supported catalyst.

In pre-1940 publications, the supports were only considered as physical carriers on which the catalytic metal or oxide was disposed as broadly and uniformly as possible. But over the years, a better understanding of the cofunctioning of catalysts and their supports has been achieved. It was recognized that the support was actually a promoter in many cases. In Catalysis (Berkman et al. 1940), the difference between a promoter and a support is described as the difference in quantity: when the support exceeds the quantity of the catalyst, it is a support; otherwise it is a promoter. This view was more or less simplistic, but implied the recognition that even at this early year the support was a catalytic component in the broadly construed catalytic composition.

An early purpose of the support was to obtain a solid granular material coated with catalytic component, providing a hard and stable structure to withstand disintegration under gas or liquid flows. Another purpose to load catalytical noble metal on supports is to dilute noble metals in a larger volume. Some supports act as a stabilizer to prevent lower-melting-point materials from agglomeration. Another use of the support was to serve as a reservoir for semi-molten salts.

Many experiments about alumina were conducted at the early period, which helped people to realize that catalysts supported on different species of alumina have different catalytic properties. [6] [7] During the same time frame, it was noticed that the catalyst and the support were cooperating in some cases to produce two simultaneous and mutually beneficial reactions. This was called the dual-functioning catalyst and was observed in those hydrodenitrogenation, hydrodesulfurization, and reforming catalysts reactions.

Traditional carbon materials as supports

Carbon is a ubiquitous element that forms millions of compounds, ranging from simple carbon monoxide to highly complex enzymes. Regarding to its elemental form, although there is no catalytic properties ascribed to diamond, graphite is known to be an active catalyst in some oxidation reactions. Graphitic carbon is also used as a support material where other catalytic components may be dispersed, resulting in an increase of the surface area they expose to the chemical reactants.

The applications of graphite, carbon black and activated charcoal manufactured annually as catalyst support are relatively few. The major catalytical use of charcoals and carbon blacks is to support metals. In addition, charcoals are sometimes used to support compounds such as sulfides and halides. Some graphite is used to support metals, but the most important feature of graphite is its ability to form intercalates, which are the catalysts for some hydrogenation, dehydrogenation, isomerization, alkylation, hydrodealkylation, polymerization and ammonia formation reactions. For charcoal and carbon black-supported metals with various industrial uses, the methods of manufacture can be divided into three broad groups based on the catalytic metal loaded: wet impregnation, hydrolysis impregnation and chemical vapor deposition (CVD). [8]

Carbon nanotubes as supports

Properties

Schematic of CNT-supported catalyst Figure 1. Schematic diagram of CNTs supported catalyst.png
Schematic of CNT-supported catalyst

Many textbooks describe carbon nanotubes (CNTs) in easily understood terms: carbon nanotubes are tubular structures made entirely of rolled-up layers of graphene. [9] [10] The diameters of CNTs ranges from about one nanometer to tens of nanometers, while their lengths can be up to centimeters, much greater than the diameters. In general, the hollow geometry of CNTs leads to large specific surface areas, which makes CNTs extremely attractive supports for heterogeneous catalysts. Another advantage of CNTs is their relatively high oxidation stability which is induced by their structural integrity and chemical inertness. Additionally, CNTs have exceptional physical properties [2] [11] [12] [13] [14] [15] including electrical conductivity, mechanical strength and thermal conductivity, which are important factors for catalyst supports. CNTs can be either metallic or semiconductive, depending on their helicity and diameter, and this property can greatly affect charge transfer processes. CNTs possess a very large Young's modulus, as well as a great tensile strength, and their flexibility property makes them an ideal component for applications in composite materials. CNTs also have good thermal conductivity, which helps to prevent the agglomeration and growth of small nanoparticles during post-annealing treatments, and stabilize newly formed phases.

In summary, CNTs are tough and tensile, owning good electron conductivity and chemical inertness, as well as thermal conductivity. Therefore, they become ideal and unique templates for nanoparticle immobilization, which allows the construction of designed nanoarchitectures. This makes CNTs extremely attractive supports for heterogeneous catalysts and related technologies. [16]

Preparation of carbon nanotubes

CNTs are generally produced by four main techniques: arc discharge, laser ablation, molten salt intercalation, and chemical vapor deposition. Since as-produced CNTs usually contain a variety of impurities such as graphene fragments, amorphous carbon, fullerenes and metal catalyst particles. [17] Since the impurities interfere with most of our desired properties and influence biocompatibility of CNTs, impairing the catalytical performance and limiting the application, they need to be purified and separated. CNTs need to be functionalized with different groups before being used in hybrid materials based on their purpose as well. Furthermore, in many applications we require uniform and stable dispersions of CNTs, but pristine single-walled CNTs (SWCNTs) are insoluble in most solvents, leading to aggregation between individual tubes. We also want to separate CNTs based on whether they are semiconducting or metallic. [18]

The production of CNTs has become easier and cheaper by the years, and the quality of as-prepared CNTs has improved since the contaminated impurities are considered. As a result, the major challenge is to develop cheap and facile methods to improve the uniformity in lengths, diameters and chirality of CNTs. CNTs has great potential as an important bridge connecting the molecular realm and the macroscopic world. [19]

Characterization

The characterization techniques of CNTs supported catalysts are varied. The most common methods include X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDS), X-Ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), scanning electron microscopy (SEM), high-resolution TEM (HRTEM), near-infrared spectroscopy, UV absorption spectroscopy, photoluminescence spectroscopy and fluorescence microscopy. These techniques and methodologies have been employed to not only comprehensively characterize CNT–nanocrystal heterostructures, but also thoroughly investigate the properties of these hybrid materials. [20]

Preparation

To obtain a CNTs supported catalyst, the first step is to load the catalytic materials onto CNTs. A variety of synthesis strategies for the CNT/metal nanoparticle hybrids can be classified as ex situ and in situ techniques. [18]

Ex situ approaches

Ex situ approaches utilize different interactions including covalent interactions, noncovalent interactions, π-π stacking and electrostatic interactions.

Covalent interactions are used to attach inorganic nanoparticles with various function group terminals to CNTs treated by acids. One typical example is amide bond. [21] [22] Because of the excellent biological compatibility of Au, they are so frequently used in biosensing, medical and other related fields. Au nanoparticles have been linked to acid treated CNTs by aminothiols, bifunctional thiols or thioether bonds. [23] Hydrophilic metal oxides such as MnO2, [24] MgO, [25] TiO2 [26] and Zr(SO4)2 [27] can be directly attached to the carboxyl groups, averting the use and separation of linking agent. On the other hand, however, the interactions are relatively weak, and the distribution of the nanoparticles are not as uniform.

Besides covalent bonds, the linkage between catalytic particles and pure CNTs can also be achieved by noncovalent interactions such as van der Waals interactions, hydrogen bonding, π-π stacking, and electrostatic interactions. The surfactant sodium dodecylsulfate (SDS) is widely used to attach diverse nanoparticles including Pt, [28] EuF3, TbF3 [29] and SiO2 [30] [31] to multi-walled carbon nanotubes (MWCNTs). In another approach which utilizes hydrophobic capping agents, for instance, octanethiols [32] and dodecanethiols, [33] [34] both coverage and morphology of the hybrid materials can be well controlled by modifying the length and functional groups of the chains. A similar route is to make use of the delocalized π electrons of CNTs as well as those in aromatic organic compounds containing polar group terminated alkyl chains. [35] [36] [37] [38] [39] The most distinguished advantage of this method is that pyrene compounds are absorpted on CNTs, which improves the solubility of CNTs, together with dispersibility and charge transfer ability of loaded nanoparticles. In another simple and facile approach where electrostatic interactions are utilized, ionic polyelectrolytes are deposited on CNTs so as to attract charged nanoparticles. [40] [41] [42] [43]

In situ approaches

In situ approaches are alternatives for ex situ approaches with a better control of particle dispersion. Inorganic compounds are directly formed on the surface of CNTs via a variety of techniques including electrochemical techniques, sol-gel process, hydrothermal and aerosol techniques and gas-phase deposition.

Electrochemistry is a method that controls the nucleation and growth process of noble metals and alloys efficaciously. Metal complexes in solutions can be reduced by electrons provided on electrodes to form metal nanoparticles, and the size of the metal nanoparticles and their coverage on the sidewalls of CNTs can be controlled by changing electrochemical deposition parameters such as deposition time and nucleation potential. [44] [45]

Sol-gel process is a commonly used solution-based process which can produce glass and ceramic materials of different shapes. [46] In this process, the reactants (usually metal salts or metal organic compounds) go through a series of hydrolysis and condensation reactions and form colloidal or polymeric sols, followed by an aging process to convert the sols into gels. Then gels are then desiccated drying under supercritical conditions and converted into aerogel. This is a cheap technique avoiding the requirement of high temperature, enabling fine controls in chemical composition as well as lowest concentration of dopants. But it also shows the weakness that the product will typically contain an amorphous phase, thus crystallization and post-annealing steps are required and increase the complexity of preparation.

Hydrothermal techniques are developed in recent years. [47] The advantage of this method is to get crystalline particles or films without post-annealing and calcinations. Formation of inorganic nanowires and nanorods can also be achieved by the forced crystallization in hydrothermal process. [48]

In addition, various gas-phase deposition methods are used to load inorganic catalytical particles onto CNTs surface. Among the most commonly used gas-phase deposition methods, chemical [49] [50] [51] [52] and physical [53] [54] [55] [56] vapor depositions enjoy an advantage in excellent control over the size, shape and uniformity. Thin and continuous films can be deposited on carbon substrates, retaining the 3D integrity. Other physical techniques such as sputtering [57] [58] [59] [60] and pulsed laser deposition (PLD), together with chemical methods (for instance, atomic layer deposition (ALD) [61] [62] [63] ), are good alternatives to deposit desired particles on CNTs.

Limitations

One general difficulty to deposit catalytic metal or metal oxides on CNTs is to control the size and distribution of the particles. Many of these preparations suffer from deposition scarcity, unwanted large size or aggregates of catalyst particles even at a relatively low loading content. On the other hand, in order to decorate CNTs with catalytic particles, a functionalization process is generally required beforehand: this makes the preparation more complex and increases the cost. In addition, after attaching functional groups on CNTs, the properties of CNTs are usually affected, and the performance of as-prepared hybrid material will be impaired as a result. For these reasons, more facile preparation methods with less impact on the properties of CNTs need to be developed.

Applications

Although at an early stage of research, CNTs supported metal-nanoparticle catalysts as transition metals Ru, Co, Ag, Pt, Pd, and Au shed new light to catalysis reactions in many fields such as batteries, flat panel displays, and chemical sensors. In organic synthesis like Heck reaction or Fischer–Tropsch synthesis, CNTs supported Pd or Co catalysts are applied to improve catalytic activity or to optimize experimental conditions. For the selective catalytic reduction of NOx with hydrocarbons, CNTs supported Pt–Rh catalyst displays higher NOx reduction activity.

Particularly, with hydrogen carbon-based fuel reserves rapidly running out, fuel cell and battery with application of CNTs-supported metal nanoparticles catalysts have been an active area of research. For example, catalytic hydrogenation of CO2 to produce methanol has been considered as one of the most economical and effective ways to chemically fix huge amount of emitted CO2 and also to improve climate conditions. CNTs supported Pd catalyst has considerable activity and selectivity, which is favored in hydrogenation of CO2.

However, to realize these applications from laboratory devices to industrial prototypes, further optimization is needed. Many challenges remain such as the control of the interface and the morphology, phase composition of the catalysts, and the type and quality of CNTs. Reproducibility problem can not be ignored, and a better understanding of the relationship between structures and properties is also in need.

Carbon nanotube-supported Pd catalyst

In the catalysts of Heck reaction, precious metal Pd was the most used active component. Supported Pd catalysts displayed many advantages. Compared with the traditional homogeneous Pd(OAc)2, PdCl2 catalysts in Heck reaction, CNTs-supported Pd catalyst has higher catalytic activity, better stability, easier separation and more satisfactory reusability.

In experimental process, carbon nanotube supported Pd catalysts were prepared using chemical reduction. Additional chemical reductant is used to solve the agglomeration of Pd nanoparticles. [64] [65]

Figure 2. Heck arylation catalyzed by the CNT supported palladium catalyst Heck arylation catalyzed by the CNT supported palladium catalyst.png
Figure 2. Heck arylation catalyzed by the CNT supported palladium catalyst

Carbon nanotube-supported Pd-metal catalyst

Formic acid is a non-toxic and non-explosive liquid at room temperature. It has low toxicity, facility of storage, handling and primarily high energy density. such advantages are favored for potential applications in small portable fuel cell. Carbon supported Pd catalysts have played a very important role in DFAFC (direct formic acid fuel cell) catalyst research in recent years due to their good activity as well as more efficient Pd metal utilization and lower metal loadings. [66] [67]

The mechanism of formic acid electrooxidation on Pt and Pt-group metal surfaces selection in acid solution follows the dual pathways: dehydrogenation and dehydration. [68] Multi-walled carbon nanotubes (MWCNTs) have higher nanoparticle dispersion as the support of the cathode electrocatalyst. Therefore, it showed a better performance than that electrocatalysts supported on carbon black in DEFCs (direct ethanol fuel cells).

Carbon nanotube-supported Pd-metal-oxide catalyst

Hydrogenation of CO2 has been considered as one of the most economical and effective ways in fixing huge amount of emitted CO2. Supported Pd-metal-oxide catalysts have been found to show considerable activity and selectivity for hydrogenation of CO2 to methanol, and the supporter has significant effect on the performance of the catalyst. [69]

MWCNT-supported Pd–ZnO catalysts for hydrogenation of carbon dioxide to methanol played dual roles as a catalyst supporter and a promoter. Greater amount of hydrogen can be absorbed to generate a micro-environment with higher the concentration of active H-adspecies at the surface of the functioning catalyst, thus increasing the rate of surface hydrogenation reactions. [70]

Carbon nanotubes supported Pt catalyst

Direct ethanol fuel cells (DEFC) and direct methanol fuel cells (DMFC) are highly efficient, pollution-free and noiseless energy conversion systems that can produce electricity through electrochemical reactions. They are expected to be useful as a power source for portable electronic devices including laptop computers, cell-phones, and so on. [71] The activity of electrocatalysts play a key role in the commercialization of DMFC or DEFC. Among the many electrocatalysts, Pt enjoys high electrocatalytic efficiency and has been proved to be the most effective catalysts for alcohol oxidation reactions. Bimetallic catalysts including Pt and a second precious or non-precious metal (like Ru, Rh, Sn, Pb, Sb, Ni, etc.) are often applied to enhance the electrochemical activity of Pr and at the same time avoiding its deactivation when exposed to poisoning intermediates by the bifunctional or ligand mechanisms.

As a kind of electrocatalyst support, CNTs have shown better corrosion-resistance than other catalyst supports such as carbon black under operational conditions. Besides, CNTs not only enjoy a highly electrochemically accessible surface area but can also offer a remarkable electronic conductivity due to its multi-wall structure, which properties render it a competitive electrocatalyst support for Pt-catalyst. [72]

It has been found that the electrochemical activity of different Pt-catalysts follows the order of Pt-WO3/CNT > Pt-Ru/E-TEK-Vulcan > Pt/CNT > Pt/E-TEK-Vulcan > bulk platinum. The reason why CNT based materials have higher electrochemical response is most probably due to its higher surface area that are electroactive. [73]

Carbon nanotubes supported Co nanoparticles catalyst

The Fischer–Tropsch synthesis (FTS) process needs to be catalyzed by certain transition metals as Co, Fe, and Ru which present the highest activity. [74] Among them, Co catalysts are preferred because of their high activity and selectivity to linear hydrocarbons for FTS, more stable, and low cost compared to Ru. Activated carbon has many advantages, such as resistance to acidic or basic media, stable at high temperatures, etc., serving as FTS catalyst support. [75]

Using carbon nanotubes as Co catalyst support was found to decrease the temperature of cobalt oxide species. The strong metal-support interactions are reduced greatly and the reducibility of the catalysts improved significantly. CNTs help to increase the dispersion of metal clusters and thus decreasing the average cobalt clusters size. Research showed that the hydrocarbon yield obtained by inventive CNTs supported Co catalyst is considerably larger than that obtained from Co on alumina supports. [76]

Related Research Articles

<span class="mw-page-title-main">Carbon nanotube</span> Allotropes of carbon with a cylindrical nanostructure

A carbon nanotube (CNT) is a tube made of carbon with a diameter in the nanometer range (nanoscale). They are one of the allotropes of carbon.

The Suzuki reaction is an organic reaction, classified as a cross-coupling reaction, where the coupling partners are a boronic acid and an organohalide, and the catalyst is a palladium(0) complex. It was first published in 1979 by Akira Suzuki, and he shared the 2010 Nobel Prize in Chemistry with Richard F. Heck and Ei-ichi Negishi for their contribution to the discovery and development of palladium-catalyzed cross-couplings in organic synthesis. This reaction is also known as the Suzuki–Miyaura reaction or simply as the Suzuki coupling. It is widely used to synthesize polyolefins, styrenes, and substituted biphenyls. Several reviews have been published describing advancements and the development of the Suzuki reaction. The general scheme for the Suzuki reaction is shown below, where a carbon-carbon single bond is formed by coupling a halide (R1-X) with an organoboron species (R2-BY2) using a palladium catalyst and a base. The organoboron species is usually synthesized by hydroboration or carboboration, allowing for rapid generation of molecular complexity.

The Sonogashira reaction is a cross-coupling reaction used in organic synthesis to form carbon–carbon bonds. It employs a palladium catalyst as well as copper co-catalyst to form a carbon–carbon bond between a terminal alkyne and an aryl or vinyl halide.

<span class="mw-page-title-main">Heterogeneous catalysis</span> Type of catalysis involving reactants & catalysts in different phases of matter

Heterogeneous catalysis is catalysis where the phase of catalysts differs from that of the reactants or products. The process contrasts with homogeneous catalysis where the reactants, products and catalyst exist in the same phase. Phase distinguishes between not only solid, liquid, and gas components, but also immiscible mixtures, or anywhere an interface is present.

Nanomaterial-based catalysts are usually heterogeneous catalysts broken up into metal nanoparticles in order to enhance the catalytic process. Metal nanoparticles have high surface area, which can increase catalytic activity. Nanoparticle catalysts can be easily separated and recycled. They are typically used under mild conditions to prevent decomposition of the nanoparticles.

<span class="mw-page-title-main">Carbon nanofiber</span>

Carbon nanofibers (CNFs), vapor grown carbon fibers (VGCFs), or vapor grown carbon nanofibers (VGCNFs) are cylindrical nanostructures with graphene layers arranged as stacked cones, cups or plates. Carbon nanofibers with graphene layers wrapped into perfect cylinders are called carbon nanotubes.

<span class="mw-page-title-main">Nanocomposite</span> Solid material with nano-scale structure

Nanocomposite is a multiphase solid material where one of the phases has one, two or three dimensions of less than 100 nanometers (nm) or structures having nano-scale repeat distances between the different phases that make up the material.

In organic chemistry, carbon–hydrogen bond functionalization is a type of organic reaction in which a carbon–hydrogen bond is cleaved and replaced with a C−X bond. The term usually implies that a transition metal is involved in the C−H cleavage process. Reactions classified by the term typically involve the hydrocarbon first to react with a metal catalyst to create an organometallic complex in which the hydrocarbon is coordinated to the inner-sphere of a metal, either via an intermediate "alkane or arene complex" or as a transition state leading to a "M−C" intermediate. The intermediate of this first step can then undergo subsequent reactions to produce the functionalized product. Important to this definition is the requirement that during the C−H cleavage event, the hydrocarbyl species remains associated in the inner-sphere and under the influence of "M".

Magnetic nanoparticles are a class of nanoparticle that can be manipulated using magnetic fields. Such particles commonly consist of two components, a magnetic material, often iron, nickel and cobalt, and a chemical component that has functionality. While nanoparticles are smaller than 1 micrometer in diameter, the larger microbeads are 0.5–500 micrometer in diameter. Magnetic nanoparticle clusters that are composed of a number of individual magnetic nanoparticles are known as magnetic nanobeads with a diameter of 50–200 nanometers. Magnetic nanoparticle clusters are a basis for their further magnetic assembly into magnetic nanochains. The magnetic nanoparticles have been the focus of much research recently because they possess attractive properties which could see potential use in catalysis including nanomaterial-based catalysts, biomedicine and tissue specific targeting, magnetically tunable colloidal photonic crystals, microfluidics, magnetic resonance imaging, magnetic particle imaging, data storage, environmental remediation, nanofluids, optical filters, defect sensor, magnetic cooling and cation sensors.

<span class="mw-page-title-main">Electrocatalyst</span> Catalyst participating in electrochemical reactions

An electrocatalyst is a catalyst that participates in electrochemical reactions. Electrocatalysts are a specific form of catalysts that function at electrode surfaces or, most commonly, may be the electrode surface itself. An electrocatalyst can be heterogeneous such as a platinized electrode. Homogeneous electrocatalysts, which are soluble, assist in transferring electrons between the electrode and reactants, and/or facilitate an intermediate chemical transformation described by an overall half reaction. Major challenges in electrocatalysts focus on fuel cells.

<span class="mw-page-title-main">Carbon nanotube chemistry</span>

Carbon nanotube chemistry involves chemical reactions, which are used to modify the properties of carbon nanotubes (CNTs). CNTs can be functionalized to attain desired properties that can be used in a wide variety of applications. The two main methods of CNT functionalization are covalent and non-covalent modifications.

Carbocatalysis is a form of catalysis that uses heterogeneous carbon materials for the transformation or synthesis of organic or inorganic substrates. The catalysts are characterized by their high surface areas, surface functionality, and large, aromatic basal planes. Carbocatalysis can be distinguishable from supported catalysis in that no metal is present, or if metals are present they are not the active species.

<span class="mw-page-title-main">Single-walled carbon nanohorn</span>

Single-walled carbon nanohorn is the name given by Sumio Iijima and colleagues in 1999 to horn-shaped sheath aggregate of graphene sheets. Very similar structures had been observed in 1994 by Peter J.F. Harris, Edman Tsang, John Claridge and Malcolm Green. Ever since the discovery of the fullerene, the family of carbon nanostructures has been steadily expanded. Included in this family are single-walled and multi-walled carbon nanotubes, carbon onions and cones and, most recently, SWNHs. These SWNHs with about 40–50 nm in tubule length and about 2–3 nm in diameter are derived from SWNTs and ended by a five-pentagon conical cap with a cone opening angle of ~20o. Moreover, thousands of SWNHs associate with each other to form the ‘dahlia-like' and ‘bud-like’ structured aggregates which have an average diameter of about 80–100 nm. The former consists of tubules and graphene sheets protruding from its surface like petals of a dahlia, while the latter is composed of tubules developing inside the particle itself. Their unique structures with high surface area and microporosity make SWNHs become a promising material for gas adsorption, biosensing, drug delivery, gas storage and catalyst support for fuel cell. Single-walled carbon nanohorns are an example of the family of carbon nanocones.

<span class="mw-page-title-main">Graphitic carbon nitride</span> Class of chemical compounds

Graphitic carbon nitride (g-C3N4) is a family of carbon nitride compounds with a general formula near to C3N4 (albeit typically with non-zero amounts of hydrogen) and two major substructures based on heptazine and poly(triazine imide) units which, depending on reaction conditions, exhibit different degrees of condensation, properties and reactivities.

Filamentous carbon is a carbon-containing deposit structure that refers to several allotropes of carbon, including carbon nanotubes, carbon nanofibers, and microcoils. It forms from gaseous carbon compounds. Filamentous carbon structures all contain metal particles. These are either iron, cobalt, or nickel or their alloys. Deposits of it also significantly disrupt synthesis gas methanation. Acetylene is involved in a number of method of the production of filamentous carbon. The structures of filamentous carbon are mesoporous and on the micrometer scale in dimension. Most reactions that form the structures take place at or above 280 °C (536 °F).

<span class="mw-page-title-main">Chemiresistor</span>

A chemiresistor is a material that changes its electrical resistance in response to changes in the nearby chemical environment. Chemiresistors are a class of chemical sensors that rely on the direct chemical interaction between the sensing material and the analyte. The sensing material and the analyte can interact by covalent bonding, hydrogen bonding, or molecular recognition. Several different materials have chemiresistor properties: metal-oxide semiconductors, some conductive polymers, and nanomaterials like graphene, carbon nanotubes and nanoparticles. Typically these materials are used as partially selective sensors in devices like electronic tongues or electronic noses.

<span class="mw-page-title-main">Copper nanoparticle</span>

A copper nanoparticle is a copper based particle 1 to 100 nm in size. Like many other forms of nanoparticles, a copper nanoparticle can be prepared by natural processes or through chemical synthesis. These nanoparticles are of particular interest due to their historical application as coloring agents and the biomedical as well as the antimicrobial ones.

<span class="mw-page-title-main">Synthesis of carbon nanotubes</span> Class of manufacturing

Techniques have been developed to produce carbon nanotubes in sizable quantities, including arc discharge, laser ablation, high-pressure carbon monoxide disproportionation, and chemical vapor deposition (CVD). Most of these processes take place in a vacuum or with process gases. CVD growth of CNTs can occur in vacuum or at atmospheric pressure. Large quantities of nanotubes can be synthesized by these methods; advances in catalysis and continuous growth are making CNTs more commercially viable.

Vertically aligned carbon nanotube arrays (VANTAs) are a unique microstructure consisting of carbon nanotubes oriented with their longitudinal axis perpendicular to a substrate surface. These VANTAs effectively preserve and often accentuate the unique anisotropic properties of individual carbon nanotubes and possess a morphology that may be precisely controlled. VANTAs are consequently widely useful in a range of current and potential device applications.

Nitrogen-doped carbon nanotubes (N-CNTs) can be produced through five main methods; chemical vapor deposition (CVD), high-temperature and high-pressure reactions, gas-solid reaction of amorphous carbon with NH3 at high temperature, solid reaction, and solvothermal synthesis.

References

  1. ↑ Chen, Xiaoqi; Xiao, Jianping; Wang, Jian; Deng, Dehui; Hu, Yongfeng; Zhou, Jigang; Yu, Liang; Heine, Thomas; Pan, Xiulian; Bao, Xinhe (2015). "Visualizing electronic interactions between iron and carbon by X-ray chemical imaging and spectroscopy". Chem. Sci. 6 (5): 3262–3267. doi:10.1039/C5SC00353A. PMC   5490425 . PMID   28706694. Open Access logo PLoS transparent.svg
  2. 1 2 Dresselhaus, M. S.; Dresselhaus, G.; Avouris, Ph., eds. (2001). "Carbon nanotubes: synthesis, structures, properties and applications". Topics in Applied Physics. Berlin. 80. ISBN   978-3-540-41086-7.
  3. ↑ IUPAC, Compendium of Chemical Terminology, 2nd ed. (the "Gold Book") (1997). Online corrected version: (2006–) "catalyst"
  4. ↑ Krijn P de Jong (1999). "Synthesis of supported catalysts". Current Opinion in Solid State and Materials Science. 4 (1): 55–62. Bibcode:1999COSSM...4...55D. doi:10.1016/S1359-0286(99)80012-6.
  5. ↑ Hwang, Gan-Lin (2003) U.S. Patent 6,841,509 "Carbon nanocapsule supported catalysts"
  6. ↑ U.S. Patent 3,244,644 (4-5-66) "Method of Preparing a Catalyst Composition Consisting of Eta-Alumina and the Product Thereof"
  7. ↑ U.S. Patent 3,186,957 (6-1-65) "Method of Preparing a Nickel Oxide Alumina Composition and the Product Thereof"
  8. ↑ Stiles, Alvin B. (1987). Catalyst Supports and Supported Catalysts: Theoretical and Applied Concepts. Butterworths. ISBN   978-0409951486.
  9. ↑ Iijima, S. (1991). "Helical microtubules of graphitic carbon". Nature. 354 (6348): 56–58. Bibcode:1991Natur.354...56I. doi:10.1038/354056a0. S2CID   4302490.
  10. ↑ Iijima, S.; Ichihashi, Toshinari (1993). "Single-shell carbon nanotubes of 1-nm diameter". Nature. 363 (6430): 603–605. Bibcode:1993Natur.363..603I. doi:10.1038/363603a0. S2CID   4314177.
  11. ↑ Harris, P. J. F. (2003). Carbon Nanotubes and Related Structures. Cambridge, U.K.: Cambridge University Press. ISBN   978-0521005333.
  12. ↑ Saito, R.; Dresselhaus, G.; Dresselhaus, M. S. (1998). Physical Properties of Carbon Nanotubes. London: Imperial College Press. ISBN   978-1860942235.
  13. ↑ Ajayan, P. M. (1999). "Nanotubes from Carbon". Chem. Rev. 99 (7): 1787–1800. doi:10.1021/cr970102g. PMID   11849010.
  14. ↑ Terrones, M. (2003). "SCIENCE AND TECHNOLOGY OF THE TWENTY-FIRST CENTURY: Synthesis, Properties, and Applications of Carbon Nanotubes". Annu. Rev. Mater. Res. 33: 419–501. Bibcode:2003AnRMS..33..419T. doi:10.1146/annurev.matsci.33.012802.100255.
  15. ↑ Dresselhaus, M. S.; Dresselhaus, G.; Charlier, J. C.; Hernandez, E. (2004). "Electronic, thermal and mechanical properties of carbon nanotubes". Philosophical Transactions of the Royal Society A . 362 (1823): 2065–2098. Bibcode:2004RSPTA.362.2065D. CiteSeerX   10.1.1.512.5536 . doi:10.1098/rsta.2004.1430. PMID   15370472. S2CID   32523882.
  16. ↑ Gregory, G. W.; Craig, E. B.; Richard, G. C. (2006). "Metal Nanoparticles and Related Materials Supported on Carbon Nanotubes: Methods and Application". Small. 2 (2): 182–193. doi:10.1002/smll.200500324. PMID   17193018.
  17. ↑ Salzmann, C. G.; Llewellyn, S. A.; Tobias, G.; Ward, M. A. H.; Huh, Y.; Green, M. L. H. (2007). "The Role of Carboxylated Carbonaceous Fragments in the Functionalization and Spectroscopy of a Single-Walled Carbon-Nanotube Material". Adv. Mater. 19 (6): 883–887. Bibcode:2007AdM....19..883S. doi:10.1002/adma.200601310.
  18. 1 2 Dominik, E. (2010). "Carbon Nanotube-Inorganic Hybrids". Chem. Rev. 110 (3): 1348–1385. doi:10.1021/cr800433k. PMID   20108978.
  19. ↑ Nikolaos, K.; Nikos, T. (2010). "Current Progress on the Chemical Modification of Carbon Nanotubes". Chem. Rev. 110 (9): 5366–5397. doi:10.1021/cr100018g. PMID   20545303.
  20. ↑ Xiaohui Peng; Jingyi Chen; James A. Misewich; Stanislaus S. Wong. (2009). "Carbon nanotube–nanocrystal heterostructures". Chem. Soc. Rev. 38 (4): 1076–1098. doi:10.1039/b811424m. PMID   19421582.
  21. ↑ Chen, J; Hamon, MA; Hu, H; Chen, Y; Rao, AM; Eklund, PC; Haddon, RC (1998). "Solution properties of single-walled carbon nanotubes". Science. 282 (5386): 95–8. Bibcode:1998Sci...282...95C. doi:10.1126/science.282.5386.95. PMID   9756485.
  22. ↑ Banerjee, Sarbajit; Wong, Stanislaus S. (2002). "Synthesis and Characterization of Carbon Nanotube−Nanocrystal Heterostructures". Nano Lett. 2 (3): 195–200. Bibcode:2002NanoL...2..195B. doi:10.1021/nl015651n.
  23. ↑ Zanella, R.; Basiuk, E. V.; Santiago, P.; Basiuk, V. A.; Mireles, E.; Puente-Lee, I.; Saniger, J. M. (2005). "Deposition of gold nanoparticles onto thiol-functionalized multiwalled carbon nanotubes". J. Phys. Chem. B. 109 (34): 16290–5. doi:10.1021/jp0521454. PMID   16853071.
  24. ↑ Wang, G.-X.; Zhang, B.-L.; Yu, Z.-L.; Qu, M.-Z. (2005). "Manganese oxide/MWNTs composite electrodes for supercapacitors". Solid State Ionics. 176 (11–12): 1169–1174. doi:10.1016/j.ssi.2005.02.005.
  25. ↑ Liu, B.; Chen, J. H.; Xiao, C. H.; Cui, K. Z.; Yang, L.; Pang, H. L.; Kuang, Y. F. (2007). "Preparation of Pt/MgO/CNT Hybrid Catalysts and Their Electrocatalytic Properties for Ethanol Electrooxidation". Energy Fuels. 21 (3): 1365–1369. doi:10.1021/ef060452i.
  26. ↑ Kongkanand, A.; Dominguez, R. M.; Kamat, P. V. (2007). "Single wall carbon nanotube scaffolds for photoelectrochemical solar cells. Capture and transport of photogenerated electrons". Nano Lett. 7 (3): 676–80. Bibcode:2007NanoL...7..676K. doi:10.1021/nl0627238. PMID   17309316.
  27. ↑ Juan, J. C.; Jiang, Y.; Meng, X.; Cao, W.; Yarmo, M. A.; Zhang (2007). "Supported zirconium sulfate on carbon nanotubes as water-tolerant solid acid catalyst". J. Mater. Res. Bull. 42 (7): 1278–1285. doi:10.1016/j.materresbull.2006.10.017.
  28. ↑ Lee, C. L.; Ju, Y. C.; Chou, P. T.; Huang, Y. C.; Kuo, L.-C.; Oung, J. C. (2004). "Preparation of Pt nanoparticles on carbon nanotubes and graphite nanofibers via self-regulated reduction of surfactants and their application as electrochemical catalyst". Electrochem. Commun. 7 (4): 453–458. doi:10.1016/j.elecom.2005.01.016.
  29. ↑ Wei, X. W.; Xu, J.; Song, X. J.; Ni, Y. H. Zhongguo (2004). Zhongguo Youse Jinshu Xuebao/Chinese Journal of Nonferrous Metals. 14: 236.{{cite journal}}: Missing or empty |title= (help)
  30. ↑ Whitsitt, E. A.; Moore, V. C.; Smalley, R. E.; Barron, A. R. (2005). "LPD silica coating of individual single walled carbon nanotubes". J. Mater. Chem. 15 (44): 4678. doi:10.1039/b509869f.
  31. ↑ Whitsitt, E. A.; Barron, A. R. (2003). "Silica Coated Single Walled Carbon Nanotubes". Nano Lett. 3 (6): 775–778. Bibcode:2003NanoL...3..775W. doi:10.1021/nl034186m.
  32. ↑ Ellis, A. V.; Vijayamohanan, K.; Goswami, R.; Chakrapani, N.; Ramanathan, L. S.; Ajayan, P. M.; Ramanath, G. (2003). "Hydrophobic Anchoring of Monolayer-Protected Gold Nanoclusters to Carbon Nanotubes". Nano Lett. 3 (3): 279–282. Bibcode:2003NanoL...3..279E. doi:10.1021/nl025824o.
  33. ↑ Rahman, G. M.; Guldi, D. M.; Zambon, E.; Pasquato, L.; Tagmatarchis, N.; Prato, M. (2005). "Dispersable carbon nanotube/gold nanohybrids: Evidence for strong electronic interactions". Small. 1 (5): 527–30. doi:10.1002/smll.200400146. PMID   17193482.
  34. ↑ Han, L.; Wu, W.; Kirk, F. L.; Luo, J.; Maye, M. M.; Kariuki, N. N.; Lin, Y.; Wang, C.; Zhong, C.-J. (2004). "A direct route toward assembly of nanoparticle-carbon nanotube composite materials". Langmuir. 20 (14): 6019–6025. doi:10.1021/la0497907. PMID   16459625.
  35. ↑ Yang, D. Q.; Hennequin, B.; Sacher, E. (2006). "XPS Demonstration of π−π Interaction between Benzyl Mercaptan and Multiwalled Carbon Nanotubes and Their Use in the Adhesion of Pt Nanoparticles". Chem. Mater. 18 (21): 5033–5038. doi:10.1021/cm061256s.
  36. ↑ Murakami, H.; Nomura, T.; Nakashima, N. (2003). "Noncovalent porphyrin-functionalized single-walled carbon nanotubes in solution and the formation of porphyrin–nanotube nanocomposites". Chem. Phys. Lett. 378 (5–6): 481–485. Bibcode:2003CPL...378..481M. doi:10.1016/S0009-2614(03)01329-0.
  37. ↑ Wang, X.; Liu, Y.; Qiu, W.; Zhu, D. (2002). "Immobilization of tetra-tert-butylphthalocyanines on carbon nanotubes: A first step towards the development of new nanomaterials". J. Mater. Chem. 12 (6): 1636–1639. doi:10.1039/b201447e.
  38. ↑ D’Souza, F.; Chitta, R.; Sandanayaka, A. S. D.; Subbaiyan, N. K.; D’Souza, L.; Araki, Y.; Ito, O. (2007). "Self-assembled single-walled carbon nanotube:zinc-porphyrin hybrids through ammonium ion-crown ether interaction: Construction and electron transfer". Chem. Eur. J. 13 (29): 8277–84. doi:10.1002/chem.200700583. PMID   17625800.
  39. ↑ Mu, Y.; Liang, H.; Hu, J.; Jiang, L.; Wan, L. (2005). "Controllable pt nanoparticle deposition on carbon nanotubes as an anode catalyst for direct methanol fuel cells". J. Phys. Chem. B. 109 (47): 22212–6. doi:10.1021/jp0555448. PMID   16853891.
  40. ↑ Correa-Duarte, M. A.; Liz Marza´n, L. M. (2006). "Carbon nanotubes as templates for one-dimensional nanoparticle assemblies". J. Mater. Chem. 16: 22–25. doi:10.1039/b512090j.
  41. ↑ Ostranger, J. W.; Mamedov, A. A.; Kotov, N. A. (2001). "Two modes of linear layer-by-layer growth of nanoparticle—polylectrolyte multilayers and different interactions in the layer-by-layer deposition". J. Am. Chem. Soc. 123 (6): 1101–10. doi:10.1021/ja0029578. PMID   11456663.
  42. ↑ Jiang, K.; Eitan, A.; Schadler, L. S.; Ajayan, P. M.; Siegel, R. W.; Grobert, N.; Mayne, M.; Reyes-Reyes, M.; Terrones, H.; Terrones, M. (2003). "Selective Attachment of Gold Nanoparticles to Nitrogen-Doped Carbon Nanotubes". Nano Lett. 3 (3): 275–277. Bibcode:2003NanoL...3..275J. doi:10.1021/nl025914t.
  43. ↑ Correa-Duarte, M. A.; Perez-Juste, J.; Sanchez-Iglesias, A.; Giersig, M. (2005). "Aligning Au Nanorods by Using Carbon Nanotubes as Templates". Angew. Chem. Int. Ed. 44 (28): 4375–4378. doi:10.1002/anie.200500581. PMID   15954145.
  44. ↑ Guo, D. J.; Li, H. L. (2004). "Electrochemical synthesis of Pd nanoparticles on functional MWNT surfaces". Electrochem. Commun. 6 (10): 999–1003. doi:10.1016/j.elecom.2004.07.014.
  45. ↑ Wei, B.-Y.; Hsu, M.-C.; Su, P.-G.; Lin, H.-M.; Wu, R.-J.; Lai, H.-J. (2004). "A novel SnO2 gas sensor doped with carbon nanotubes operating at room temperature". Sens. Actuators B. 101 (1–2): 81–89. doi:10.1016/j.snb.2004.02.028.
  46. ↑ Brinker, C. J.; Scherer, G. W. (1990). Sol-Gel Sciences The Physics and Chemistry of Sol-Gel Processing. New York: Academic Press. ISBN   978-0121349707.
  47. ↑ Yoshimura, M.; Byrappa, K. (2008). "Hydrothermal processing of materials: Past, present and future". J. Mater. Sci. 43 (7): 2085–2103. Bibcode:2008JMatS..43.2085Y. doi:10.1007/s10853-007-1853-x. S2CID   137590599.
  48. ↑ Menzel, Robert; Peiró, Ana M.; Durrant, James R.; Shaffer, Milo S. P. (2006). "Impact of Hydrothermal Processing Conditions on High Aspect Ratio Titanate Nanostructures". Chem. Mater. 18 (25): 6059–6068. doi:10.1021/cm061721l.
  49. ↑ Kuang, Qin; Li, Song-Fei; Xie, Zhao-Xiong; Lin, Shui-Chao; Zhang, Xian-Hua; Xie, Su-Yuan; Huang, Rong-Bin; Zheng, Lan-Sun (2006). "Controllable fabrication of SnO2-coated multiwalled carbon nanotubes by chemical vapor deposition". Carbon. 44 (7): 1166–1172. doi:10.1016/j.carbon.2005.11.001.
  50. ↑ Li, Chensha; Wang, Dazhi; Wang, Xiaofeng; Liang, Ji (2005). "Controlled electrochemical oxidation for enhancing the capacitance of carbon nanotube composites". Carbon. 43 (7): 1557–1560. doi:10.1016/j.carbon.2004.12.025.
  51. ↑ Peng, H. B.; Golovchenko, J. A. (2004). "Coulomb blockade in suspended Si[sub 3]N[sub 4]-coated single-walled carbon nanotubes" (PDF). Appl. Phys. Lett. 84 (26): 5428. Bibcode:2004ApPhL..84.5428P. doi:10.1063/1.1765733.
  52. ↑ Pan, L.; Shoji, T.; Nagataki, A.; Nakayama, Y. (2007). "Field Emission Properties of Titanium Carbide Coated Carbon Nanotube Arrays". Adv. Eng. Mater. 9 (7): 584–587. doi:10.1002/adem.200700064. S2CID   137465780.
  53. ↑ Kim, H.; Sigmund, W. (2002). "Zinc oxide nanowires on carbon nanotubes". Appl. Phys. Lett. 81 (11): 2085. Bibcode:2002ApPhL..81.2085K. doi:10.1063/1.1504877.
  54. ↑ Yu, Ke; Zhang, Y. S.; Xu, F.; Li, Q.; Zhu, Z. Q.; Wan, Q. (2006). "Significant improvement of field emission by depositing zinc oxide nanostructures on screen-printed carbon nanotube films". Appl. Phys. Lett. 88 (15): 153123. Bibcode:2006ApPhL..88o3123Y. doi:10.1063/1.2195115.
  55. ↑ Zhang, Y; Franklin, Nathan W; Chen, Robert J; Dai, Hongjie (2000). "Metal coating on suspended carbon nanotubes and its implication to metal–tube interaction". Chem. Phys. Lett. 331 (1): 35–41. Bibcode:2000CPL...331...35Z. doi:10.1016/S0009-2614(00)01162-3.
  56. ↑ Pan, Lujun; Konishi, Yasumoto; Tanaka, Hiroyuki; Chakrabarti, Supriya; Hokushin, Shogo; Akita, Seiji; Nakayama, Yoshikazu (2007). "Effect of MgO coating on field emission of a stand-alone carbon nanotube". Journal of Vacuum Science and Technology B. 25 (5): 1581. Bibcode:2007JVSTB..25.1581P. doi:10.1116/1.2770740.
  57. ↑ Ye, JS; Cui, HF; Liu, X; Lim, TM; Zhang, WD; Sheu, FS (2005). "Preparation and characterization of aligned carbon nanotube-ruthenium oxide nanocomposites for supercapacitors". Small. 1 (5): 560–5. doi:10.1002/smll.200400137. PMID   17193486.
  58. ↑ Kim, Hyoun Woo; Shim, Seung Hyun; Lee, Jong Woo (2007). "SiOx-sheathed carbon nanotubes prepared via a sputtering technique". Carbon. 45 (13): 2695–2698. doi:10.1016/j.carbon.2007.08.032.
  59. ↑ Zhu, Y.; Elim, H. I.; Foo, Y.-L.; Yu, T.; Liu, Y.; Ji, W.; Lee, J.-Y.; Shen, Z.; Wee, A. T. S. (2006). "Multiwalled Carbon Nanotubes Beaded with ZnO Nanoparticles for Ultrafast Nonlinear Optical Switching". Adv. Mater. 18 (5): 587–592. Bibcode:2006AdM....18..587Z. doi:10.1002/adma.200501918. S2CID   8195423.
  60. ↑ Jin, Feng; Liu, Yan; Day, Christopher M. (2007). "Barium strontium oxide coated carbon nanotubes as field emitters". Appl. Phys. Lett. 90 (14): 143114. Bibcode:2007ApPhL..90n3114J. doi:10.1063/1.2719645.
  61. ↑ Ikuno, Takashi; Yasuda, Tatsuro; Honda, Shin-Ichi; Oura, Kenjiro; Katayama, Mitsuhiro; Lee, Jung-Goo; Mori, Hirotaro (2005). "Coating carbon nanotubes with inorganic materials by pulsed laser deposition". J. Appl. Phys. 98 (11): 114305–114305–4. Bibcode:2005JAP....98k4305I. doi:10.1063/1.2035891.
  62. ↑ Ikuno, Takashi; Katayama, Mitsuhiro; Kamada, Kazunori; Honda, Shin-Ichi; Lee, Jung-Goo; Mori, Hirotaro; Oura, Kenjiro (2003). "Insulator-Coated Carbon Nanotubes Synthesized by Pulsed Laser Deposition". Jpn. J. Appl. Phys. Lett. 42 (11B): L1356. Bibcode:2003JaJAP..42L1356I. doi:10.1143/JJAP.42.L1356. S2CID   96796372.
  63. ↑ Gomathi, A.; Vivekchand, S. R. C.; Govindaraj, A.; Rao, C. N. R. (2005). "Chemically Bonded Ceramic Oxide Coatings on Carbon Nanotubes and Inorganic Nanowires". Adv. Mater. 17 (22): 2757–2761. Bibcode:2005AdM....17.2757G. doi:10.1002/adma.200500539. S2CID   137689009.
  64. ↑ Zhang, Yan; Chu, Wei Xie; Lijuan Sun, Wenjing (2010). "Preparation and Catalytic Performance of Carbon Nanotube Supported Palladium Catalyst". Chinese Journal of Chemistry. 28 (6): 879–883. doi:10.1002/cjoc.201090165.
  65. ↑ Avelino, C.; Hermenegildo, G.; Antonio, L. (2005). "Catalytic activity of palladium supported on single wall carbon nanotubes compared to palladium supported on activated carbon: Study of the Heck and Suzuki couplings, aerobic alcohol oxidation and selective hydrogenation". J. Mol. Catal. A. 230 (1–2): 97–105. doi:10.1016/j.molcata.2004.11.030.
  66. ↑ Z.L. Liu; L. Hong; M.P. Tham; T.H. Lim; H.X. Jiang (2006). "Nanostructured Pt/C and Pd/C catalysts for direct formic acid fuel cells". J. Power Sources. 161 (2): 831–835. Bibcode:2006JPS...161..831L. doi:10.1016/j.jpowsour.2006.05.052.
  67. ↑ R. Larsen; S. Ha; J. Zakzeski; R.I. Masel (2006). "Unusually active palladium based catalysts for the electrooxidation of formic acid". J. Power Sources. 157 (1): 78–84. Bibcode:2006JPS...157...78L. doi:10.1016/j.jpowsour.2005.07.066.
  68. ↑ R. Parsons; T. VanderNoot (1988). "The oxidation of small organic-molecules -a survey of recent fuel-cell related research". J. Electroanal. Chem. 257 (1–2): 9. doi:10.1016/0022-0728(88)87028-1.
  69. ↑ Fujitani, T; Saito, M; Kanai, Y; Watanabe, T; Nakamura, J; Uchijima, T (1995). "Development of an active Ga2O3 supported palladium catalyst for the synthesis of methanol from carbon dioxide and hydrogen". Applied Catalysis A: General. 125 (2): L199. doi:10.1016/0926-860X(95)00049-6.
  70. ↑ Liang, Xue-Lian; Dong, Xin; Lin, Guo-Dong; Zhang, Hong-Bin (2009). "Carbon nanotube-supported Pd–ZnO catalyst for hydrogenation of CO2 to methanol". Applied Catalysis B: Environmental. 88 (3–4): 315–322. doi:10.1016/j.apcatb.2008.11.018.
  71. ↑ Chen, C.Y.; Liu, D.H.; Huang, C.L.; Chang, C.L. (2007). "Portable DMFC system with methanol sensor-less control". Journal of Power Sources. 167 (2): 442–449. Bibcode:2007JPS...167..442C. doi:10.1016/j.jpowsour.2007.02.056.
  72. ↑ S. S. Dipti; U.C. Chung; W.S. Chung (2009). "Carbon supported Pt–Ni nanoparticles as catalysts in direct methanol fuel cells". Materials Science-Poland. 27: 521.
  73. ↑ Serp, P (2003). "Carbon nanotubes and nanofibers in catalysis". Applied Catalysis A: General. 253 (2): 337–358. doi:10.1016/S0926-860X(03)00549-0.
  74. ↑ E. Iglesia (1997). "Design, synthesis, and use of cobalt-based Fischer–Tropsch synthesis catalysts". Appl. Catal. 161 (1–2): 59–78. doi:10.1016/S0926-860X(97)00186-5.
  75. ↑ Van Berge, P.J; Van De Loosdrecht, J; Barradas, S; Van Der Kraan, A.M (2000). "Oxidation of cobalt based Fischer–Tropsch catalysts as a deactivation mechanism". Catalysis Today. 58 (4): 321–334. doi:10.1016/S0920-5861(00)00265-0.
  76. ↑ Tavasoli, A.; Sadagiani, K.; Khorashe, F.; Seifkordi, A.A.; Rohani, A.A.; Nakhaeipour, A. (2008). "Cobalt supported on carbon nanotubes — A promising novel Fischer–Tropsch synthesis catalyst" (PDF). Fuel Processing Technology. 89 (5): 491–498. doi:10.1016/j.fuproc.2007.09.008.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.