Continuous Tone-Coded Squelch System

Last updated November 08, 2023

In telecommunications, Continuous Tone-Coded Squelch System or CTCSS is one type of in-band signaling that is used to reduce the annoyance of listening to other users on a shared two-way radio communication channel. It is sometimes referred to as tone squelch or PL for Private Line, a trademark of Motorola.^[1] It does this by adding a low frequency audio tone to the voice. Where more than one group of users is on the same radio frequency (called co-channel users), CTCSS circuitry mutes those users who are using a different CTCSS tone or no CTCSS.

CTCSS tone codes are sometimes referred to as sub-channels, but this is a misnomer because no additional radio channels are created. All users with different CTCSS tones on the same channel are still transmitting on the identical radio frequency, and their transmissions interfere with each other; however; the interference is masked under most conditions. Although it provides some protection against interference, CTCSS does not offer any security against interception or jamming, and receivers without CTCSS enabled will still hear all traffic.

A receiver with just a carrier or noise squelch does not suppress any sufficiently strong signal; in CTCSS mode it unmutes only when the signal also carries the correct sub-audible audio tone. The tones are not actually below the range of human hearing, but are poorly reproduced by most communications-grade speakers and in any event are usually filtered out before being sent to the speaker or headphone.

Theory of operation

Radio transmitters using CTCSS always transmit their own tone code whenever the transmit button is pressed. The tone is transmitted at a low level simultaneously with the voice. This is called CTCSS encoding. CTCSS tones range from 67 to 257 Hz. The tones are usually referred to as sub-audible tones. In an FM two-way radio system, CTCSS encoder levels are usually set for 15% of system deviation. For example, in a 5 kHz deviation system, the CTCSS tone level would normally be set to 750 Hz deviation. Engineered systems may call for different level settings in the 500 Hz to 1 kHz (10–20%) range.

The ability of a receiver to mute the audio until it detects a carrier with the correct CTCSS tone is called decoding. Receivers are equipped with features to allow the CTCSS "lock" to be disabled. On a base station console, a microphone may have a split push-to-talk button. Pressing one half of the button, (often marked with a speaker icon or the letters "MON", short for "MONitor") disables the CTCSS decoder and reverts the receiver to hearing any signal on the channel. This is called the monitor function. There is sometimes a mechanical interlock: the user must push down and hold the monitor button or the transmit button is locked and cannot be pressed. This interlock option is referred to as compulsory monitor before transmit (the user is forced to monitor by the hardware design of the equipment itself). On mobile radios, the microphone is usually stored in a hang-up clip or a hang-up box containing a microphone clip. When the user pulls the microphone out of the hang-up clip to make a call, a switch in the clip (box) forces the receiver to revert to conventional carrier squelch mode ("monitor"). Some designs relocate the switch into the body of the microphone itself. In hand-held radios, an LED indicator may glow green, yellow, or orange to indicate another user is talking on the channel. Hand-held radios usually have a switch or push-button to monitor. Some modern radios have a feature called "Busy Channel Lockout", which will not allow the user to transmit as long as the radio is receiving another signal.

A CTCSS decoder is based on a very narrow bandpass filter which passes the desired CTCSS tone. The filter's output is amplified and rectified, creating a DC voltage whenever the desired tone is present. The DC voltage is used to turn on, enable, or unmute the receiver's speaker audio stages. When the tone is present, the receiver is unmuted, when it is not present the receiver is silent.

Because period is the inverse of frequency, lower tone frequencies can take longer to decode (depends on the decoder design). Receivers in a system using 67.0 Hz can take noticeably longer to decode than ones using 203.5 Hz, and they can take longer than one decoding 250.3 Hz. In some repeater systems, the time lag can be significant. The lower tone may cause one or two syllables to be clipped before the receiver audio is unmuted (is heard). This is because receivers are decoding in a chain. The repeater receiver must first sense the carrier signal on the input, then decode the CTCSS tone. When that occurs, the system transmitter turns on, encoding the CTCSS tone on its carrier signal (the output frequency). All radios in the system start decoding after they sense a carrier signal then recognize the tone on the carrier as valid. Any distortion on the encoded tone will also affect the decoding time.

Engineered systems often use tones in the 127.3 Hz to 162.2 Hz range to balance fast decoding with keeping the tones out of the audible part of the receive audio. Most amateur radio repeater controller manufacturers offer an audio delay option—this delays the repeated speech audio for a selectable number of milliseconds before it is retransmitted. During this fixed delay period (the amount of which is adjusted during installation, then locked down), the CTCSS decoder has enough time to recognize the right tone. This way the problem with lost syllables at the beginning of a transmission can be overcome without having to use higher frequency tones.

In early systems, it was common to avoid the use of adjacent tones. On channels where every available tone is not in use, this is good engineering practice. For example, an ideal would be to avoid using 97.4 Hz and 100.0 Hz on the same channel. The tones are so close that some decoders may periodically false trigger. The user occasionally hears a syllable or two of co-channel users on a different CTCSS tone talking. As electronic components age, or through production variances, some radios in a system may be better than others at rejecting nearby tone frequencies.

Digital-Coded Squelch

CTCSS is an analog system. A later Digital-Coded Squelch (DCS) system was developed by Motorola under the trademarked name Digital Private Line (DPL). General Electric responded with the same system under the name of Digital Channel Guard (DCG). The generic name is CDCSS (Continuous Digital-Coded Squelch System). The use of digital squelch on a channel that has existing tone squelch users precludes the use of the 131.8 and 136.5 Hz tones as the digital bit rate is 134.4 bits per second and the decoders set to those two tones will sense an intermittent signal (referred to in the two-way radio field as "falsing" the decoder).^[2]

List of tones

CTCSS tones
NS ^{[lower-alpha 1]}	PL	Hz	Notes
1	XZ	67.0
39	WZ	69.3	^{[lower-alpha 2]}
2	XA	71.9
3	WA	74.4
4	XB	77.0
5	WB	79.7	^{[lower-alpha 3]}
6	YZ	82.5
7	YA	85.4
8	YB	88.5
9	ZZ	91.5
10	ZA	94.8
11	ZB	97.4	^{[lower-alpha 4]}
12	1Z	100.0
13	1A	103.5
14	1B	107.2
15	2Z	110.9
16	2A	114.8
17	2B	118.8
18	3Z	123.0
19	3A	127.3
20	3B	131.8
21	4Z	136.5
22	4A	141.3
23	4B	146.2
NATO		150.0	^{[lower-alpha 5]}^{[lower-alpha 6]}
24	5Z	151.4
25	5A	156.7
40		159.8	^{[lower-alpha 6]}
26	5B	162.2
41		165.5	^{[lower-alpha 6]}
27	6Z	167.9
42		171.3	^{[lower-alpha 6]}
28	6A	173.8
43		177.3	^{[lower-alpha 6]}
29	6B	179.9
44		183.5	^{[lower-alpha 6]}
30	7Z	186.2
45		189.9	^{[lower-alpha 6]}
31	7A	192.8
46		196.6	^{[lower-alpha 6]}
47		199.5	^{[lower-alpha 6]}
32	M1	203.5
48	8Z	206.5	^{[lower-alpha 7]}^{[lower-alpha 6]}
33	M2	210.7
34	M3	218.1
35	M4	225.7
49	9Z	229.1	^{[lower-alpha 7]}^{[lower-alpha 6]}
36	M5	233.6
37	M6	241.8
38	M7	250.3
50	0Z	254.1	^{[lower-alpha 7]}^{[lower-alpha 6]}

CTCSS tones are standardized by the EIA/TIA. The full list of the tones can be found in their original standard RS-220A,^[3] and the most recent EIA/TIA-603-E;^[4] the CTCSS tones also may be listed in manufacturers instruction, maintenance or operational manuals. Some systems use non-standard tones.^[5] The NATO Military radios use 150.0 Hz, and this can be found in the user manuals for the radios. Some areas do not use certain tones. For example, the tone of 100.0 Hz is avoided in the United Kingdom since this is twice the UK mains power line frequency; an inadequately smoothed power supply may cause unwanted squelch opening (this is true in many other areas that use 50 Hz power). Tones typically come from one of three series as listed below along with the two character PL code used by Motorola to identify tones. The most common set of supported tones is a set of 39 tones including all tones with Motorola PL codes, except for the tones 8Z, 9Z, and 0Z (zero-Z).^[6] The lowest series has adjacent tones that are roughly in the harmonic ratio of 2^0.05 to 1 (≈1.035265), while the other two series have adjacent tones roughly in the ratio of 10^0.015 to 1 (≈1.035142). An example technical description can be found in a Philips technical information sheet about their CTCSS products.^[7]

Notes

↑ Non-standard numerical codes. Many radios use a matching set of numerical codes to represent corresponding tones; however, there is no published standard and only partial industry adoption.
↑ Some radios use 69.4 Hz instead, which better fits the harmonic sequence, and this tone is often omitted as a choice.
↑ Also known by the code SP.
↑ Not actually in this harmonic sequence, but an average of the ZA and 1Z tones used to fill the gap between the lower and middle sequences. 98.1 Hz would be the tone after ZA, and the tone before 1Z would be 96.6 Hz, assuming the same harmonics were used.
↑ Many NATO military radios have a switchable 150.0 Hz tone. The list includes the following radios: AN/PRC-68, AN/PRC-117F, AN/PRC-117G, AN/PRC-77, AN/PRC-113, AN/PRC-137, AN/PRC-139, AN/PRC-152, AN/PRC-119, AN/VRC-12, AN/PSC-5, and Thales AN/PRC-148 MBITR.
1 2 3 4 5 6 7 8 9 10 11 12 Non-standard tone not included in current TIA-603-E.
1 2 3 The 8Z, 9Z, and 0Z ("zero-Z") tones are often omitted from radios that use the M1–M7 series of tones.

Reverse CTCSS

Some professional systems use a phase-reversal of the CTCSS tone at the end of a transmission to eliminate the squelch crash or squelch tail. This is common with General Electric Mobile Radio and Motorola systems. When the user releases the push-to-talk button the CTCSS tone does a phase shift for about 200 milliseconds. In older systems, the tone decoders used mechanical reeds to decode CTCSS tones. When audio at a resonant pitch was fed into the reed, it would resonate, which would turn on the speaker audio. The end-of-transmission phase reversal (called "Reverse Burst" by Motorola (and trademarked by them) and "Squelch Tail Elimination" or "STE" by GE ^[8]) caused the reed to abruptly stop vibrating which would cause the receive audio to instantly mute. Initially, a phase shift of 180 degrees was used, but experience showed that a shift of ±120 to 135 degrees was optimal in halting the mechanical reeds. These systems often have audio muting logic set for CTCSS only. If a transmitter without the phase reversal feature is used, the squelch can remain unmuted for as long as the reed continues to vibrate—up to 1.5 seconds at the end of a transmission as it coasts to a stop (sometimes referred to as the "flywheel effect" or called "freewheeling").

Interference and CTCSS

In non-critical uses, CTCSS can also be used to hide the presence of interfering signals such as receiver-produced intermodulation. Receivers with poor specifications—such as scanners or low-cost mobile radios—cannot reject the strong signals present in urban environments. The interference will still be present and may block the receiver, but the decoder will prevent it from being heard. It will still degrade system performance but the user will not have to hear the noises produced by receiving the interference.

CTCSS is commonly used in VHF and UHF amateur radio operations for this purpose. Wideband and extremely sensitive radios are common in the amateur radio field, which imposes limits on achievable intermodulation and adjacent-channel performance.^[9]

Family Radio Service (FRS), PMR446 and other consumer-grade radios often include a feature called "Interference Eliminator Codes", "sub-channels", or "privacy codes". These do not afford privacy or security, but serve only to reduce annoying interference by other users or other noise sources; a receiver with the tone squelch turned off will hear everything on the channel.^[10] GMRS/FRS radios offering CTCSS codes typically provide a choice of 38 tones, but the tone number and the tone frequencies used may vary from one manufacturer to another (or even within product lines of one manufacturer) and should not be assumed to be consistent (i.e. "Tone 12" in one set of radios may not be "Tone 12" in another).^[11]

Related Research Articles

In telecommunications, squelch is a circuit function that acts to suppress the audio output of a receiver in the absence of a strong input signal. Essentially, squelch is a specialized type of noise gate designed to suppress weak signals. Squelch is used in two-way radios and VHF/UHF radio scanners to eliminate the sound of noise when the radio is not receiving a desired transmission.

<span class="mw-page-title-main">Radiotelephone</span> Communications system for transmission of speech over radio

A radiotelephone, abbreviated RT, is a radio communication system for conducting a conversation; radiotelephony means telephony by radio. It is in contrast to radiotelegraphy, which is radio transmission of telegrams (messages), or television, transmission of moving pictures and sound. The term is related to radio broadcasting, which transmit audio one way to listeners. Radiotelephony refers specifically to two-way radio systems for bidirectional person-to-person voice communication between separated users, such as CB radio or marine radio. In spite of the name, radiotelephony systems are not necessarily connected to or have anything to do with the telephone network, and in some radio services, including GMRS, interconnection is prohibited.

Multichannel Television Sound, better known as MTS, is the method of encoding three additional audio channels into analog 4.5 MHz audio carriers on System M and System N. It was developed by the Broadcast Television Systems Committee, an industry group, and sometimes known as BTSC as a result.

PSK31 or "Phase Shift Keying, 31 Baud", also BPSK31 and QPSK31, is a popular computer-sound card-generated radioteletype mode, used primarily by amateur radio operators to conduct real-time keyboard-to-keyboard chat, most often using frequencies in the high frequency amateur radio bands (near-shortwave). PSK31 is distinguished from other digital modes in that it is specifically tuned to have a data rate close to typing speed, and has an extremely narrow bandwidth, allowing many conversations in the same bandwidth as a single voice channel. This narrow bandwidth makes better use of the RF energy in a very narrow space thus allowing relatively low-power equipment to communicate globally using the same skywave propagation used by shortwave radio stations.

A walkie-talkie, more formally known as a handheld transceiver (HT), is a hand-held, portable, two-way radio transceiver. Its development during the Second World War has been variously credited to Donald Hings, radio engineer Alfred J. Gross, Henryk Magnuski and engineering teams at Motorola. First used for infantry, similar designs were created for field artillery and tank units, and after the war, walkie-talkies spread to public safety and eventually commercial and jobsite work.

AM stereo is a term given to a series of mutually incompatible techniques for radio broadcasting stereo audio in the AM band in a manner that is compatible with standard AM receivers. There are two main classes of systems: independent sideband (ISB) systems, promoted principally by American broadcast engineer Leonard R. Kahn; and quadrature amplitude modulation (QAM) multiplexing systems.

Professional mobile radio are person-to-person two-way radio voice communications systems which use portable, mobile, base station, and dispatch console radios. PMR radio systems are based on such standards as MPT-1327, TETRA, APCO 25, and DMR which are designed for dedicated use by specific organizations, or standards such as NXDN intended for general commercial use. These systems are used by police, fire, ambulance, and emergency services, and by commercial firms such as taxis and delivery services. Most systems are half-duplex, in which multiple radios share a common radio channel, and only one can transmit at a time. Transceivers are normally in receive mode, the user presses a push-to-talk button on his microphone when he wants to talk, which turns on his transmitter and turns off his receiver. They use channels in the VHF and UHF bands, giving them a limited range, usually 3 to 20 miles depending on terrain. Output power is typically limited to 4 watts. Repeaters installed on tall buildings, hills or mountain peaks are used to increase the range of systems.

Project 25 is a suite of standards for interoperable digital two-way radio products. P25 was developed by public safety professionals in North America and has gained acceptance for public safety, security, public service, and commercial applications worldwide. P25 radios are a direct replacement for analog UHF radios, but add the ability to transfer data as well as voice, allowing for more natural implementations of encryption and text messaging. P25 radios are commonly implemented by dispatch organizations, such as police, fire, ambulance and emergency rescue service, using vehicle-mounted radios combined with repeaters and handheld walkie-talkie use.

<span class="mw-page-title-main">FM broadcasting</span> Radio transmission of audio by frequency modulation

FM broadcasting is a method of radio broadcasting that uses frequency modulation (FM) of the radio broadcast carrier wave. Invented in 1933 by American engineer Edwin Armstrong, wide-band FM is used worldwide to transmit high-fidelity sound over broadcast radio. FM broadcasting offers higher fidelity—more accurate reproduction of the original program sound—than other broadcasting techniques, such as AM broadcasting. It is also less susceptible to common forms of interference, having less static and popping sounds than are often heard on AM. Therefore, FM is used for most broadcasts of music and general audio. FM radio stations use the very high frequency range of radio frequencies.

A land mobile radio system (LMRS) is a person-to-person voice communication system consisting of two-way radio transceivers which can be stationary, mobile, or portable.

An amateur radio repeater is an electronic device that receives a weak or low-level amateur radio signal and retransmits it at a higher level or higher power, so that the signal can cover longer distances without degradation. Many repeaters are located on hilltops or on tall buildings as the higher location increases their coverage area, sometimes referred to as the radio horizon, or "footprint". Amateur radio repeaters are similar in concept to those used by public safety entities, businesses, government, military, and more. Amateur radio repeaters may even use commercially packaged repeater systems that have been adjusted to operate within amateur radio frequency bands, but more often amateur repeaters are assembled from receivers, transmitters, controllers, power supplies, antennas, and other components, from various sources.

Selcall is a type of squelch protocol used in radio communications systems, in which transmissions include a brief burst of sequential audio tones. Receivers that are set to respond to the transmitted tone sequence will open their squelch, while others will remain muted.

GE Marc V is a historic U.S. format or protocol of trunked, two-way radio introduced by General Electric Mobile Radio in the early 1980s. This equipment was also sold in Australia. The product name looks and sounds similar to GE-Mark V, a turbine controller made by General Electric. GE developed the EDACS radio system based on its success with Marc V.

In telecommunications, falsing is a signaling error condition when a signal decoder detects a valid input although the implied protocol function was not intended. This is also known as a false decode. Other forms are referred to as talk-off.

Mobile radio or mobiles refer to wireless communications systems and devices which are based on radio frequencies, and where the path of communications is movable on either end. There are a variety of views about what constitutes mobile equipment. For US licensing purposes, mobiles may include hand-carried,, equipment. An obsolete term is radiophone.

In a conventional, analog two-way radio system, a standard radio has noise squelch or carrier squelch, which allows a radio to receive all transmissions. Selective calling is used to address a subset of all two-way radios on a single radio frequency channel. Where more than one user is on the same channel, selective calling can address a subset of all receivers or can direct a call to a single radio. Selective calling features fit into two major categories—individual calling and group calling. Individual calls generally have longer time-constants: it takes more air-time to call an individual radio unit than to call a large group of radios.

MDC, also known as Stat-Alert, MDC-1200 and MDC-600, is a Motorola two-way radio low-speed data system using audio frequency shift keying, (AFSK). MDC-600 uses a 600 baud data rate. MDC-1200 uses a 1,200 baud data rate. Systems employ either one of the two baud rates. Mark and space tones are 1,200 Hz and 1,800 Hz. The data are sent in bursts over the radio system's voice channel.

Remote controls are used any time a two-way radio base station is located away from the desk or office where communication originates. For example, a dispatch center for taxicabs may have an office downtown but have a base station on a distant mountain top. A Tone remote, also known as an EIA Tone remote, is a signaling system used to operate a two-way radio base station by some form of remote control.

The Yaesu FT-2900R is a VHF 2M FM mobile amateur radio transceiver. It is no longer in production and has been replaced by the FT-2980.

A reed receiver or tuned reed receiver (US) was a form of multi-channel signal decoder used for early radio control systems. It uses a simple electromechanical device or 'resonant reed' to demodulate the signal, in effect a receive-only modem. The encoding used is a simple form of frequency-shift keying.

References

↑ Romanchik, Dan (February 4, 2022). "No Nonsense Technician Class License Study Guide" (PDF). p. 121. Retrieved August 19, 2023.
↑ Morris, Mike (January 29, 2013). "A Historical and Technical Overview of Tone Squelch Systems" . Retrieved March 6, 2013.
↑ EIA Standard RS-220-A, Continuous Tone-Controlled Squelch Systems (CTCSS). March 1979.
↑ Land Mobile FM or PM – Communications Equipment – Measurement and Performance Standards, TIA-603-E (Technical report). Telecommunications Industry Association. March 2, 2016. p. 10.
↑ List of non-standard CTCSS codes
↑ "CTCSS Compatibility in FRS Radios". Archived from the original on September 24, 2001.
↑ "Information Sheet: Continuous Tone Controlled Squelch System" (PDF). Retrieved July 8, 2019.
↑ Explanation of Reverse Burst & "And Squelch" Archived January 19, 2008, at the Wayback Machine - Kevin K. Custer W3KKC
↑ Wilson, Mark J., ed. (2007). The ARRL Operating Manual for Radio Amateurs. American Radio Relay League. pp. 2-12–2-13. ISBN 0872591093.
↑ Silver, H. Ward (2011). Two-Way Radios and Scanners for Dummies. John Wiley & Sons. pp. 62–64. ISBN 1118054601.
↑ Eisner, Robert H. (July 23, 1999). "CTCSS Compatibility in FRS Radios". Archived from the original on September 27, 2014. Retrieved January 23, 2023.

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.

[NB-3] Non-standard numerical codes. Many radios use a matching set of numerical codes to represent corresponding tones; however, there is no published standard and only partial industry adoption.

[WZ-4] Some radios use 69.4 Hz instead, which better fits the harmonic sequence, and this tone is often omitted as a choice.

[WB-5] Also known by the code SP.

[ZB-6] Not actually in this harmonic sequence, but an average of the ZA and 1Z tones used to fill the gap between the lower and middle sequences. 98.1 Hz would be the tone after ZA, and the tone before 1Z would be 96.6 Hz, assuming the same harmonics were used.

[NATO-7] Many NATO military radios have a switchable 150.0 Hz tone. The list includes the following radios: AN/PRC-68, AN/PRC-117F, AN/PRC-117G, AN/PRC-77, AN/PRC-113, AN/PRC-137, AN/PRC-139, AN/PRC-152, AN/PRC-119, AN/VRC-12, AN/PSC-5, and Thales AN/PRC-148 MBITR.

[xx-8] 1 2 3 4 5 6 7 8 9 10 11 12 Non-standard tone not included in current TIA-603-E.

[xZ-9] 1 2 3 The 8Z, 9Z, and 0Z ("zero-Z") tones are often omitted from radios that use the M1–M7 series of tones.

[1] Romanchik, Dan (February 4, 2022). "No Nonsense Technician Class License Study Guide" (PDF). p. 121. Retrieved August 19, 2023.

[2] Morris, Mike (January 29, 2013). "A Historical and Technical Overview of Tone Squelch Systems" . Retrieved March 6, 2013.

[10] EIA Standard RS-220-A, Continuous Tone-Controlled Squelch Systems (CTCSS). March 1979.

[11] Land Mobile FM or PM – Communications Equipment – Measurement and Performance Standards, TIA-603-E (Technical report). Telecommunications Industry Association. March 2, 2016. p. 10.

[12] List of non-standard CTCSS codes

[13] "CTCSS Compatibility in FRS Radios". Archived from the original on September 24, 2001.

[14] "Information Sheet: Continuous Tone Controlled Squelch System" (PDF). Retrieved July 8, 2019.

[15] Explanation of Reverse Burst & "And Squelch" Archived January 19, 2008, at the Wayback Machine - Kevin K. Custer W3KKC

[16] Wilson, Mark J., ed. (2007). The ARRL Operating Manual for Radio Amateurs. American Radio Relay League. pp. 2-12–2-13. ISBN 0872591093.

[17] Silver, H. Ward (2011). Two-Way Radios and Scanners for Dummies. John Wiley & Sons. pp. 62–64. ISBN 1118054601.

[18] Eisner, Robert H. (July 23, 1999). "CTCSS Compatibility in FRS Radios". Archived from the original on September 27, 2014. Retrieved January 23, 2023.

[1]

[2]

[lower-alpha 1]

[lower-alpha 2]

[lower-alpha 3]

[lower-alpha 4]

[lower-alpha 5]

[lower-alpha 6]

[lower-alpha 7]

[3]

[4]

[5]

[6]

[7]

[8]

[9]

[10]

[11]

v t e Two-way radio
Amateur and hobbyist	Amateur radio Amateur radio repeater Citizens band radio Family Radio Service Public Radio Service General Mobile Radio Service KDR 444 LPD433 Mobile rig Multi-Use Radio Service PMR446 UHF CB (Australia)
Aviation (aeronautical mobile)	Air traffic control Aircraft emergency frequency Airband Common traffic advisory frequency Mandatory frequency airport MULTICOM Single Frequency Approach UNICOM
Land-based commercial and government mobile	Base station Business band Mobile radio Professional mobile radio Radio repeater Specialized Mobile Radio Trunked radio system Walkie-talkie
Marine (shipboard)	2182 kHz 500 kHz Coast radio station Marine VHF radio Maritime mobile amateur radio
Signaling / Selective calling	CTCSS D-STAR Dual-tone multi-frequency MDC-1200 Push-to-talk Quik-Call I Quik-Call II Selcall SELCAL
System elements and principles	Antenna APRS Automatic vehicle location Call sign CAD DC remote Dispatch Dynamic range compression Fade margin Link budget Rayleigh fading Tone remote Radiotelephony procedure Voting (diversity combining)