Corvette leaf spring

Last updated

A Corvette leaf spring is a type of independent suspension that utilizes a fiber-reinforced plastic (FRP) mono-leaf spring instead of more conventional coil springs. It is named after the Chevrolet Corvette, [1] the American sports car for which it was originally developed and first utilized. [2] [3] [4] [5] [6] A notable characteristic of this suspension configuration is the mounting of the mono-leaf spring such that it can serve as both ride spring and anti-roll spring. In contrast to many applications of leaf springs in automotive suspension designs, this type does not use the spring as a locating link. While this suspension type is most notably associated with several generations of the Chevrolet Corvette the design has been used in other production General Motors cars, as well as vehicles from Volvo Cars and Mercedes-Benz Sprinter van. Fiat produced cars with a similar configuration, using a multi-leaf steel spring in place of the FRP mono-leaf spring.

Contents

Design

The C5 Corvette's rear suspension Leafs2.jpg
The C5 Corvette's rear suspension

The leaf-spring suspension configuration is independent, because the movement of one wheel is not determined by the position of the other. [6] Control arms are utilized to define the motion of the wheel as the suspension is compressed. The usual coil springs are replaced with a single FRP spring, which spans the width of the car. As in independent suspension systems using coil springs, and unlike the common leaf-spring supported Hotchkiss rear axle, the suspension kinematics are defined only by the control arms.

As in a coil-spring suspension design, the FRP mono-leaf spring supports the weight of the vehicle. However, the FRP leaf springs differ from steel coils and traditional steel multi-leaf springs in a number of significant ways. The FRP plastic springs have 4.3–5.5 times the strain energy storage per weight, compared to steel. [7] This results in a lighter spring for a given application. The single FRP mono-leaf front spring used on the fourth-generation Corvette is 33 percent of the weight of an equivalent set of coil springs. [8] Comparing FRP to conventional steel leaf springs in similar applications, the weight saved is even greater. The third-generation Corvette offered an optional FRP mono-leaf spring as an alternative to the standard multi-leaf steel spring, the 22-kilogram (48 lb) steel spring being replaced by a 3-kilogram (7 lb) FRP spring. [9] Volvo claims a weight savings of 5 kilograms (10 lb) by using a FRP spring in the rear suspension of its second-generation XC90, compared to designs using coil springs. [10]

The relative sliding movement of the leaves of a multi-leaf steel spring results in stiction-based hysteresis with respect to spring compression. This stiction reduces suspension compliance and can compromise both ride quality and handling. [11] Lacking individual leaves, the mono-leaf spring avoids stiction. [8]

FRP springs are advertised as having exceptional cycle life and corrosion resistance. [8] A GM test comparing the third-generation Corvette springs found that failure of the multi-leaf steel springs was likely after 200,000 full-travel cycles. The replacement FRP leaf spring showed no loss of performance after two million full cycles. [9]

Packaging is cited as both an advantage and disadvantage of the transverse FRP leaf spring, as compared to coil springs, depending on the application. The FRP spring is typically set low in the suspension, resulting in a low center of gravity. It also allows manufacturers to avoid tall spring mounts, thus resulting in a flatter load floor about the suspension. [10] James Schefter reports that, as used on the C5 and later Corvettes, the use of OEM coilover damper springs would have forced the chassis engineers to either vertically raise the shock towers or move them inward. In the rear this would have reduced trunk space. In the front this would have interfered with engine packaging. The use of the leaf spring allowed the spring to be placed under the chassis, out of the way, while keeping the diameter of the shock-absorber assembly to that of just the damper, rather than damper and spring. [12] However, in other applications, such as race car designs, the need to span the width of the vehicle resulted in significant design limitations. Coil and torsion springs present better packaging options for racing applications. FRP springs also have limited availability and selection as compared to coil springs. [13] Higher cost has also been cited as a disadvantage, when comparing FRP springs to coil springs on production road cars. [14]

Properties

FEA model of a leaf spring under load. The initial, unbent shape of the spring is shown as a silhouette box. An upward deflection on the right side of the spring results in a smaller upward movement on the left side. Deformed spring model iso and plane.JPG
FEA model of a leaf spring under load. The initial, unbent shape of the spring is shown as a silhouette box. An upward deflection on the right side of the spring results in a smaller upward movement on the left side.

An advantage of the FRP transverse leaf springs—when supported with widely spaced, pivotable mounts—is the ability to replace the anti-roll bar. Typically springs that provide a sufficient ride rate need a supplemental spring (the anti-roll bar) to increase the suspension roll rate. The coupling of the two sides of the transverse leaf spring across the vehicle results in an anti-roll bar like behavior. Corvette engineers have cited this property as enabling the use of a lighter anti-roll bar, [9] and even eliminating the rear anti-roll bar on some versions of the seventh generation Corvette. [15]

When either wheel is deflected upward, the center span of the spring (the portion between the pivotable mounts) deflects downward. If both wheels deflect upward at the same time (for example, when hitting a bump in the road) the center section bends uniformly between the pivot mounts. In a roll, only one wheel is deflected upwards, which tends to form the center of the spring into an S-shaped curve. The result is that the wheel rate of one side of the suspension depends on the displacement of the other side. [8] [9] [13] The extent to which the spring acts as an anti-roll bar depends on the distance between the pivot mounts and their rigidity. [8]

A transverse leaf spring with a central rigid mount. The two spring halves are effectively isolated. Movements of one half of the spring do not affect the other half. Rigid central mount transverse leaf spring.JPG
A transverse leaf spring with a central rigid mount. The two spring halves are effectively isolated. Movements of one half of the spring do not affect the other half.

A simplified flat, rectangular spring illustrates this principle. Deflecting the right side of the spring results in the left side rising. By comparison, a rigid central mount (2nd and 3rd generation Corvettes and other cars) shows no movement on one side when the other is deflected. [6]

Applications

A number of manufacturers have produced vehicles or concepts utilizing independent front or rear suspensions supported by transverse leaf springs that have an anti-roll effect.

Several automotive companies have filed patents for suspension designs using a transverse composite leaf-spring supported in a fashion similar to that of the Corvette.

See also

Related Research Articles

<span class="mw-page-title-main">Shock absorber</span> Mechanical component

A shock absorber or damper is a mechanical or hydraulic device designed to absorb and damp shock impulses. It does this by converting the kinetic energy of the shock into another form of energy which is then dissipated. Most shock absorbers are a form of dashpot.

<span class="mw-page-title-main">MacPherson strut</span> Type of automotive suspension design

The MacPherson strut is a type of automotive suspension system that uses the top of a telescopic damper as the upper steering pivot. It is widely used in the front suspension of modern vehicles. The name comes from American automotive engineer Earle S. MacPherson, who invented and developed the design.

<span class="mw-page-title-main">Torsion bar suspension</span> Vehicle suspension that uses a torsion bar

A torsion bar suspension, also known as a torsion spring suspension, is any vehicle suspension that uses a torsion bar as its main weight-bearing spring. One end of a long metal bar is attached firmly to the vehicle chassis; the opposite end terminates in a lever, the torsion key, mounted perpendicular to the bar, that is attached to a suspension arm, a spindle, or the axle. Vertical motion of the wheel causes the bar to twist around its axis and is resisted by the bar's torsion resistance. The effective spring rate of the bar is determined by its length, cross section, shape, material, and manufacturing process.

<span class="mw-page-title-main">Car suspension</span> Suspension system for a vehicle

Suspension is the system of tires, tire air, springs, shock absorbers and linkages that connects a vehicle to its wheels and allows relative motion between the two. Suspension systems must support both road holding/handling and ride quality, which are at odds with each other. The tuning of suspensions involves finding the right compromise. It is important for the suspension to keep the road wheel in contact with the road surface as much as possible, because all the road or ground forces acting on the vehicle do so through the contact patches of the tires. The suspension also protects the vehicle itself and any cargo or luggage from damage and wear. The design of front and rear suspension of a car may be different.

<span class="mw-page-title-main">Leaf spring</span> Type of vehicle suspension

A leaf spring is a simple form of spring commonly used for suspension in wheeled vehicles. Originally called a laminated or carriage spring, and sometimes referred to as a semi-elliptical spring, elliptical spring, or cart spring, it is one of the oldest forms of vehicle suspension. A leaf spring is one or more narrow, arc-shaped, thin plates that are attached to the axle and chassis in a way that allows the leaf spring to flex vertically in response to irregularities in the road surface. Lateral leaf springs are the most commonly used arrangement, running the length of the vehicle and mounted perpendicular to the wheel axle, but numerous examples of transverse leaf springs exist as well.

<span class="mw-page-title-main">Independent suspension</span> Vehicle suspension in which each wheel is suspended independently

Independent suspension is any automobile suspension system that allows each wheel on the same axle to move vertically independently of the others. This is contrasted with a beam axle or deDion axle system in which the wheels are linked. "Independent" refers to the motion or path of movement of the wheels or suspension. It is common for the left and right sides of the suspension to be connected with anti-roll bars or other such mechanisms. The anti-roll bar ties the left and right suspension spring rates together but does not tie their motion together.

<span class="mw-page-title-main">Ford D3 platform</span> Motor vehicle platform

The Ford D3 platform is an automobile platform assembled by Ford Motor Company. In production between the 2005 and 2019 model years, the D3 platform is the fifteenth generation of full-size cars produced by Ford in North America. Marking the adoption of unibody chassis construction, a transverse engine configuration, front-wheel drive, all-wheel drive, and the lack of a V8 engine, the D3 platform is derived from the 1998-2016 Volvo P2 architecture. Since 2008, the related D4 platform has served as a basis for crossover SUVs.

<span class="mw-page-title-main">General Motors W platform</span> Motor vehicle platform

The W-platform was a General Motors automotive platform underpinning both mid size and full-size front-wheel drive cars — across the platform's three generations from 1987-2016.

<span class="mw-page-title-main">Volvo XC90</span> Swedish mid-size luxury crossover SUV

The Volvo XC90 is a mid-size luxury SUV manufactured and marketed by Volvo Cars since 2002 and now in its second generation.

The Z platform or Z-body automobile platform designation was used on three different types of vehicles made by General Motors not including their trucks.

<span class="mw-page-title-main">Double wishbone suspension</span> Automotive independent suspension design

A double wishbone suspension is an independent suspension design for automobiles using two wishbone-shaped arms to locate the wheel. Each wishbone or arm has two mounting points to the chassis and one joint at the knuckle. The shock absorber and coil spring mount to the wishbones to control vertical movement. Double wishbone designs allow the engineer to carefully control the motion of the wheel throughout suspension travel, controlling such parameters as camber angle, caster angle, toe pattern, roll center height, scrub radius, scuff ([[Abrasion

A swing axle is a simple type of independent suspension, almost always for the rear axles, designed and patented by Edmund Rumpler in 1903. This was a revolutionary invention in automotive suspension, allowing driven (powered) wheels to follow uneven road surfaces independently, thus enabling the vehicle's wheels to maintain better road contact and holding; plus each wheel's reduced unsprung weight means their movements have less impact on the vehicle as a whole. The first automotive application was the Rumpler Tropfenwagen, later followed by the Mercedes 130H/150H/170H, the Standard Superior, the Volkswagen Beetle and its derivatives, the Chevrolet Corvair, and the roll-over prone M151 jeep amongst others.

<span class="mw-page-title-main">De Dion suspension</span>

A de Dion tube is a form of non-independent automobile suspension. It is a considerable improvement over the swing axle, Hotchkiss drive, or live axle. Because it plays no part in transmitting power to the drive wheels, it is sometimes called a "dead axle".

<span class="mw-page-title-main">Anti-roll bar</span> Device that reduces the body roll of a vehicle

An anti-roll bar is an automobile suspension part that helps reduce the body roll of a vehicle during fast cornering or over road irregularities. It links opposite front or rear wheels to a torsion spring using short lever arms for anchors. This increases the suspension's roll stiffness—its resistance to roll in turns.

<span class="mw-page-title-main">Opel GT</span> Sports car manufactured by Opel

The Opel GT is a front-engine, rear-drive two-seat sports car manufactured and marketed by Opel in two generations — separated by a 34-year hiatus.

<span class="mw-page-title-main">Chevrolet Corvette (C5)</span> Fifth generation of the Corvette sports car

The Chevrolet Corvette (C5) is the fifth generation of the Corvette sports car, produced by the Chevrolet division of General Motors for the 1997 through 2004 model years. Production variants include the high performance Z06. Racing variants include the C5-R, a 24 Hours of Daytona and 24 Hours of Le Mans GTS/GT1 winner. The C5 Corvette was the first GM vehicle to feature the third generation small block "LS" engines. Pop-up headlights were featured on a Corvette for the final time during this generation.

<span class="mw-page-title-main">Chevrolet Corvette (C4)</span> Fourth generation of the Corvette sports car

The Chevrolet Corvette (C4) is the fourth generation of the Corvette sports car, produced by American automobile manufacturer Chevrolet from 1983 until 1996. The convertible returned, as did higher performance engines, exemplified by the 375 hp (280 kW) LT5 found in the ZR-1. In early March 1990, the ZR-1 would set a new record for the highest 24 hour-5,000 mile land-speed by going over a speed of 175 mph (282 km/h). With a completely new chassis, modern sleeker styling, and other improvements to the model, prices rose and sales declined. The last C4 was produced on June 20, 1996.

<span class="mw-page-title-main">Twist-beam rear suspension</span> Type of automobile suspension

The twist-beam rear suspension is a type of automobile suspension based on a large H- or C-shaped member. The front of the H attaches to the body via rubber bushings, and the rear of the H carries each stub-axle assembly, on each side of the car. The cross beam of the H holds the two trailing arms together, and provides the roll stiffness of the suspension, by twisting as the two trailing arms move vertically, relative to each other.

<span class="mw-page-title-main">Jaguar independent rear suspension</span> Common component of a number of Jaguar production cars since 1961

Jaguar's independent rear suspension (IRS) unit has been a common component of a number of Jaguar production cars since 1961, passing through two major changes of configuration up to 2006 and last used in the Jaguar XK8 and Aston Martin DB7. This article concentrates on the first generation Jaguar IRS, which firmly established the marque's reputation for suspension sophistication, combining as it did smooth ride with excellent roadholding and low levels of noise, vibration, and harshness (NVH). The two generations overlap in time due to their being used in both full size and sports models that were updated at different times.

<span class="mw-page-title-main">Transverse leaf spring front suspension</span>

Transverse leaf spring front suspension is a type of automotive front suspension, whose usage is most well known in Ford Motor Company products from 1908 to 1948. "Suicide front axle" is a term that has been used for it.

References

  1. ↑ Corvette - The Great American Sports Car - Staff of Old Cars Weekly. F+W Media. 1975-10-02. p. 81. ISBN   9781440217647 . Retrieved 2016-11-14.[ dead link ]
  2. ↑ "The Top 5 Technological Advancements In Corvette History". Corvette Online. 2015-05-16. Retrieved 2016-11-14.
  3. ↑ "Chevrolet Corvette History". Edmunds.com. Retrieved 2016-11-14.
  4. ↑ "Composite leaf springs: Saving weight in production suspension systems". CompositesWorld. 2014-02-03. Retrieved 2016-11-14.
  5. ↑ "ACMA: Automotive Composites Alliance - Auto Composites 101: History of Automotive Composites". Autocomposites.org. Archived from the original on 2017-01-17. Retrieved 2016-11-14.
  6. 1 2 3 Chris Longhurst (2016-10-26). "The Suspension Bible". Car Bibles. Archived from the original on 2007-02-06. Retrieved 2016-11-14.
  7. ↑ Yu, W.J.; Kim, H.C. (1988). "Double tapered FRP beam for automotive suspension leaf spring". Composite Structures. 9 (4): 279–300. doi:10.1016/0263-8223(88)90049-9.
  8. 1 2 3 4 5 Lamm, Michael (1983). The Newest Corvette. Corvette from A to Z-15 (1st ed.). Lamm-Morada Publishing. p. 44. ISBN   978-0932128041. Archived from the original on February 19, 2012.
  9. 1 2 3 4 McLellan, Dave (2002). Corvette from the Inside. Cambridge, MA: Bentley Publishers. pp. 86–87. ISBN   0-8376-0859-7.
  10. 1 2 "Benteler-SGL mass-produces composite leaf springs for the new Volvo XC90 using Loctite Matrix resin from Henkel". Composites Industry News. FRP Today. Retrieved 2015-07-30.[ dead link ]
  11. ↑ Knowles, Don (2010). Today's Technician: Automotive Suspension & Steering. Cengage Learning. p. 115.
  12. ↑ Schefter, James (1998). All Corvettes Are Red. Gallery Books. ISBN   978-0671685010.
  13. 1 2 Smith, Carroll (1984). Engineer to Win. Motorbooks. p. 207. ISBN   9780879381868. If I were involved in the design of a new passenger vehicle, however, I would give serious consideration to the use of a transverse composite single leaf spring of unidirectional glass or carbon filament in an epoxy matrix. This would be the lightest practical spring configuration and, although space constraints would seem to limit its use in racing, it should be perfectly feasible on road-going vehicles, from large trucks to small commuter cars. (Since I wrote this paragraph the new-generation Corvette has come out with just such a spring to control its independent suspension systems-at both end of the car.)
  14. ↑ Edmunds, Dan. "2014 Chevrolet Corvette Stingray Z51 Suspension Walkaround". Edmunds. Retrieved 2015-07-30.
  15. ↑ Noordeloos, Marc. "Vette Engineering Manager Explains the C7 Chassis". Automobile Magazine. Retrieved 2015-08-01.
  16. ↑ McCosh, Dan (April 1998). "Luxury coupes: $24,000 a seat". Popular Science. Retrieved 2015-07-30.
  17. ↑ Schuon, Marshal (Oct 23, 1994). "Behind the Wheel/1995 Volvo 960; A Box That's Well Rounded". The New York Times. Retrieved 2015-07-30.
  18. ↑ Stoklosa, Alexander. "10 Things You Need to Know About the 2016 Volvo XC90". Car and Driver. Archived from the original on 2017-12-29. Retrieved 2015-08-01.
  19. ↑ Amanda Jacob (15 October 2014). "Volvo XC90 features polyurethane composite leaf spring". Archived from the original on 2018-02-02. Retrieved 2018-02-02.
  20. ↑ Wood, Karen. "Composite leaf springs: Saving weight in production suspension systems". Composites World. Retrieved 2015-08-01.
  21. ↑ "The Smart Fortwo Evolution" . Retrieved 2015-08-01.
  22. ↑ "Volkswagen : The 1-Litre Car". Automotive Intelligence News. Retrieved 2015-07-30.
  23. ↑ "The Successor: Indigo 3000" (PDF). Archived from the original (PDF) on 2008-12-16.
  24. ↑ "How it Works: Suspension". Unique Cars and Parts. Retrieved 2015-08-01.
  25. ↑ "Patent US7029017 – Wheel suspension for a motor vehicle with a transverse leaf spring" . Retrieved 2015-08-03.
  26. ↑ "Patent US6029987 – Front axle for a motor vehicle". 1997-05-26. Retrieved 2015-08-03.
  27. ↑ "Patent US5141209 – Transverse leaf spring type suspension". 1988-11-30. Retrieved 2015-08-03.
  28. ↑ "Patent US6811169 – Composite spring design that also performs the lower control arm function for a conventional or active suspension system" . Retrieved 2015-08-03.
  29. ↑ Buchholz, Kami (March 31, 2010). "Composites take prime chassis roles at ZF". Society of Automotive Engineers. Retrieved December 22, 2016.
  30. ↑ "Lightweight Construction: Fighting the Fab". ZF Company corporate website. ZF Company. Retrieved December 22, 2016.
This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.