1,568 to 1,759lb (711 to 798kg) (unladen U.K.spec)
The Triumph Spitfire is a British sports car manufactured over five production iterations between 1962 and 1980. Styled for Standard-Triumph in 1957 by Italian designer Giovanni Michelotti, the Spitfire was introduced at the London Motor Show in 1962.[5] It was manufactured at the Standard-Triumph Canley works, with approximately 315,000 produced over 18 years.[6]
Developed on a shortened variant of the Triumph Herald saloon's chassis, the Spitfire shared the Herald's running gear and Standard SC engine. The design used body-on-frame construction, augmented by structural components within the bodywork and rear trailing arms attached to the body rather than the chassis. A manually deployable convertible top, substantially improved on later models, provided weather protection and a bespoke hard-top was available as a factory option.
The Spitfire was conceived of by Standard-Triumph to compete in the small sports car market against the Austin-Healey Sprite. The Sprite used the drive train of the Austin A30/A35 in a new lightweight body, while the Spitfire used mechanicals from the Herald saloon. Where the Austin A30 used unitary construction, the Herald used a separate backbone chassis— which Triumph was able to downsize, saving the cost of developing a completely new chassis-body unit.
Giovanni Michelotti, who had designed the Herald, styled the bodywork, which featured wind-down windows (in contrast to the Sprite and Midget, which used side curtains) and a cowl composed of the bonnet and wings that opened forward for engine access. The Spitfire's introduction was delayed by its company's financial troubles in the early 1960's and was subsequently announced shortly after Standard Triumph was taken over by Leyland Motors. While taking stock of their new acquisition, Leyland officials found Michelotti's prototype under a dust sheet in a factory corner, and quickly approved it for production.[8]
The production design changed little from the prototype: the full-width rear bumper was replaced by two part-bumpers curving around each corner, with overriders. Mechanicals derived from the Herald saloon/sedan, with the notable addition of front disc brakes. Bodywork was bolted to the much-modified Herald chassis, the outer rails and the rear outriggers having been removed; with structural outer sills to stiffen the overall design.
Rear suspension was by a single transverse-leaf swing axle,[9] an arrangement, that unless ameliorated by any of several options, can allow rear tyres to undergo large camber changes during fast cornering, leading to oversteer– a dynamically unstable condition in which a vehicle can lose control and spin. As did many manufacturers who used a swing axle arrangement (e.g., Mercedes, Renault, Volkswagen), Triumph would later modify the rear suspension. In 1970, the rear suspension was decambered, by incorporating what Triumph called a "swing spring". One leaf was eliminated from the stack and only the bottom leaf was attached rigidly to the differential. The remaining leaves were mounted to pivot freely — thereby eliminating the worst characteristics of the original swing-axle design.
The Spitfire was an inexpensive small sports car and as such received rather basic trim by today's standards, including rubber mats and a large plastic steering wheel. It was nonetheless considered fairly comfortable at the time, as it had wind-down windows and exterior door locks, as well as relatively full instrumentation.[9] These early cars were referred to both as "Triumph Spitfire Mark Is" and "Spitfire 4s",[1] different from the later Spitfire Mark IV. The "Spitfire 4" name indicated the possibility of the appearance of a six-cylinder version.[10]
In UK specification the inline four produced 63bhp (47kW) at 5,750rpm, and 67lb⋅ft (91N⋅m) of torque at 3,500rpm. This gave a top speed of 92mph (148km/h), and a 0 to 60mph (97km/h) acceleration in 16.4 seconds. Average fuel consumption was 31 mpg.[1]
For 1964 an overdrive became optional to the four-speed manual gearbox.[5] Wire wheels and a hard top were also available.[5]
In March 1965 the Spitfire Mark II launched with a retuned engine, featuring a revised camshaft profile, water-heated intake manifold, and tubular exhaust manifold, increasing power to 67bhp (50kW) at 6,000 rpm.[1] The coil-spring design clutch of the Mark I was replaced with a Borg & Beck diaphragm spring clutch; North American models retained the coil-spring housing and were also equipped with ACDelco distributors. Exterior trim featured a new grille and badges, and the interior featured revised seats, covering most exposed surfaces with rubber cloth. Carpeting replaced the original moulded rubber floor mats.[1]
Its base price was £550; the Austin-Healey Sprite's was £505 and the MG Midget's £515.[1] Top speed was claimed to be 96mph (154km/h) and its 0–60mph time of 14.8 seconds was considered "lively".[1] The factory claimed that at highway speeds (70mph (110km/h)) the car achieved 38.1 miles per imperial gallon (7.41L/100km; 31.7mpg‑US).[1]
The Mark III, introduced in March 1967, was the first major facelift to the Spitfire. The front bumper was raised in response to new crash regulations, and the front coil springs were slightly raised. Slightly revised bonnet pressings were carried over. Rear overriders were deleted and bumper mounted reversing lights became standard (initially as two separate lights on either side of the number plate, latterly as a single light in a new unit above the number plate). The interior received a wood-veneer instrument surround and a smaller, 15-inch, wire spoked steering wheel. A folding hood replaced the earlier, more complicated design. For most of the Mark III range, the instrument cluster remained centre-mounted (as in the Mark I and Mark II), easily accommodating right-hand and left-hand drive versions.
The 1,147cc engine was replaced with a bored-out 1,296cc unit (the bore increasing from 69.3mm (2.73in) to 73.7mm (2.90in), stroke retained at 76mm (3.0in)), as fitted on the new Triumph Herald 13/60 and Triumph 1300 saloons. A new quieter exhaust gave a sweet distinct note and reduced cabin noise. In SU twin-carburettor form, the engine put out a claimed 75bhp (56kW) at 6,000 rpm, and 75lb⋅ft (102N⋅m) of torque at 4,000 rpm, and made the Mark III a comparatively quick car by the standards of the day.[citation needed] Options included wire wheels, factory hard top and a Laycock de Normanville overdrive. The Mark III was the fastest Spitfire yet, achieving 60mph (97km/h) in 13.4 seconds,[1] and reaching a top speed of 95mph (153km/h). Average fuel consumption was 33mpg.[1] The Mark III continued production into 1971, well after introduction of the Mark IV.[1]
Interior
On 8 February 1968, Standard-Triumph general manager George Turnbull drove the 100,000th Triumph Spitfire off the Canley production line.[11] More than 75% of this number had been exported outside the UK, including 45% to the US and 25% to mainland European markets.[11]
The 1968 model featured dual system (aka tandem) brakes with a brake failure warning device. The engine used a revised camshaft and a distributor with idle speed ignition timing retarded to address emissions. The twin SU carburettors now included overrun valves in the throttle discs and anti-tampering features on carburettor fuel-air mixture nuts.[12]
Starting in 1969, US-bound models were "federalised" to comply with safety and emissions regulations. A reduced compression ratio of 8.5:1 resulted in a slight decrease in power (68bhp) and 73ft-lbs of torque. However, the 0–60 time of 14 seconds was still faster than the Mark II. The instrument panel was moved in front of the driver, and new seats were introduced with integrated headrests to help against whiplash. Cosmetically, the wood dash was replaced with a matte black finished assembly intended to imitate an aircraft cockpit.
The Mark III's final production year (1970) included an integrated rear reverse and license plate lamp, side lamps at the front and rear and new badging.[13] The separate "Triumph" letters on the front of the bonnet were removed and "Triumph" and "Spitfire" rectangular badges were used in the front, rear sides and rear. A limited number of U.S. market 1970s were adorned with an RAF style "Spitfire" badge (U.K. models had a plain badge without the RAF roundel) that rested in the right corner (car opposing point of view) of the bonnet. Additional exterior changes introduced included a zip up rear window, black radiator grille and a black (vs body coloured) windscreen surround. Full wheel covers of two styles were used including the 1969 introduced model with "SPITFIRE" circumscribing the hub and a unique derivative without the branding. Interior changes included a steering column mounted ignition switch, a key-in-ignition warning buzzer, driver's side under-dash courtesy lamp and a new black spoked steering wheel. Under the bonnet, some markets had the twin SU carburettors replaced with a single Zenith-Stromberg carburettor.[13]
The Mark IV featured a redesigned rear, similar to the Triumph Stag and Triumph 2000 models, both also designed by Michelotti. The front end was revised with a new bonnet pressing, eliminating the weld lines on top of the wings, door handles were recessed, the convertible top received squared-off corners. The interior was revised to include a full-width dashboard, with instruments ahead of the driver rather than over the centre console, initially finished in black plastic and then from 1973 finished in wood.
The engine was now rated at 63 horsepower for the UK market, with a 9:1 compression ratio and twin SU HS2 carburettors. (The less powerful North American version continued to use a single Zenith Stromberg carburettor and an 8.5:1 compression ratio) due to the German DIN system; the output was the same for the early Mark IV. Performance was slower than the Mark III due to its weight increase and taller 3.89:1 final drive as opposed to the earlier 4.11:1.
The Mk. IV engine displaced 1,296cc (79.1cuin) throughout the production run, and in 1973 received larger big-end bearings to rationalise production with the TR6 2.5-litre engines. The engine was also detuned to meet new emissions regulations. With the overall weight also increasing to 1,717lb (779kg) performance dropped, with 0 to 60mph (0 to 97km/h) now in 15.8 seconds and top speed reduced to 90mph (140km/h).[1] Fuel economy was 32mpg‑imp (8.8L/100km; 26.6mpg‑US).[1]
A revised hardtop also became available, with rear quarter-lights and a flatter rear screen.
Importantly, the heavily criticised rear suspension was decambered, incorporating what Triumph called a "swing spring". One leaf of the suspension "stack" was eliminated and only the bottom leaf was attached rigidly to the differential. The remaining leaves were mounted to pivot freely — eliminating the worst characteristics of the original swing-axle. This was a different approach than that taken with the Triumph GT6 Mk II (GT6+) and Triumph Vitesse Mark 2, both of which received new lower wishbones and Rotoflex half-shaft couplings. The result on all these cars was improved handling.
The Mark IV went on sale in the UK at the end of 1970 with a base price of £735.[1]
In 1973 in the United States and Canada, and 1975 in the rest of the world, the 1500 engine was used on the MK IV body to make the Spitfire 1500. Although in this final incarnation the engine was rather rough and more prone to failure than the earlier units, torque was greatly increased by increasing the cylinder stroke to 87.5mm (3.44in), which made it much more drivable in traffic.[1]
A 1976 Spitfire 1500 photographed in London the following year
While the rest of the world saw 1500s with a compression ratio of 8.0:1, the American market model was fitted with a single Zenith-Stromberg carburettor and a compression ratio reduced to 7.5:1 to allow it to run on lower octane unleaded fuel.[1] With the addition of a catalytic converter and exhaust gas recirculating system, the engine only delivered 53bhp (40kW) (DIN) with a slower 0–60mph time of 16.3 seconds.[14] The notable exception to this was the 1976 model year, where the compression ratio was raised to 9.1:1. This improvement was short-lived, however, as the ratio was again reduced to 7.5:1 for the remaining years of production.
Rear view of a 1978 Spitfire 1500
In the UK the 9:1 compression ratio, less restrictive emissions control equipment, and the Type HS2 SU carburettors now being replaced with larger Type HS4 models,[1] led to the most powerful variant to date. The 1500 Spitfire now produced 71hp (DIN) at 5,500 rpm, and produced 82lb⋅ft (111N⋅m) of torque at 3,000 rpm.[1] Top speed was now at the 100mph (160km/h) mark, and 0 to 60mph (97km/h) was reached in 13.2 seconds.[1] Fuel economy was reduced to 29mpg.[1]
Further improvements to the suspension followed with the 1500 included longer swing axles and a lowered spring mounting point for more negative camber and a wider rear track. The wider, lower stance gave an impressive skid pad result of 0.87g average. The gearbox gained synchromesh on its bottom gear.
The final Triumph Spitfire to roll off the assembly line is this yellow 1980 hardtop example, pictured here at the British Motor Museum
The American market Spitfire 1500 is identified by large plastic over-riders and wing mounted reflectors on the front and back wings. US specification models up to 1978 featured chrome bumpers, and on the 1979 and 1980 models these were replaced by black rubber bumpers with built-in over-riders, using chassis extensions to support the bumpers.
Detail improvements continued to be made throughout the 1500's production run, including reclining seats with "chequered brushed nylon centre panels" and head restraints, introduced for domestic market cars early in 1977 along with a new set of column stalk operated minor controls (as fitted already in the TR7) replacing the old dashboard mounted knobs and switches.[15] Also added for the model's final years were a wood dash, hazard flashers and an electric screen washer, in place of the previous manual pump operated ones.[15] Options such as the hard top, tonneau cover, map light and overdrive continued to be popular, but wire wheels ceased to be available.
The 1980 model was the last and the heaviest Spitfire, weighing 1,875lb (850.5kg).[1] Base prices for the 1980 model year were $7,365 in the US and £3,631 in the UK.[1]
Assembled at Canley in August 1980 shortly before the factory closed, the last Spitfire was an Inca Yellow UK-model including the factory hardtop and overdrive options. Never sold to the public, it remains on display at the British Motor Museum.
Motorsports
Popular in street and rally racing, Spitfires won numerous SCCA National Sports Car Championships in F and G Production classes; won its class at the 1964 Tour de France rally, coming in second overall, and won the 1964 Geneva Rally. In 1965, a Spitfire won its class in the Alpine Rally.[16]
Related Research Articles
The Austin-Healey Sprite is a small open sports car produced in the United Kingdom from 1958 until 1971. The Sprite was announced to the press in Monte Carlo by the British Motor Corporation on 20 May 1958, two days after that year's Monaco Grand Prix. It was intended to be a low-cost model that "a chap could keep in his bike shed", yet be the successor to the sporting versions of the pre-war Austin Seven. The Sprite was designed by the Donald Healey Motor Company, with production being undertaken at the MG factory at Abingdon. It first went on sale for £669, using a tuned version of the Austin A-Series engine and as many other components from existing cars as possible to keep costs down.
The Triumph TR6 is a sports car that was built by the Triumph Motor Company of England. While production began several months earlier, the TR6 was officially introduced in January as a 1969 model year vehicle. The last TR6 was produced on the 20th of July 1976. Of the 91,850 TR6s produced, 83,480 were exported, almost all of them to the United States, while only 8,370 were sold in the UK.
The Triumph 2000 is a mid-sized, rear wheel drive automobile which was produced in Coventry by the Triumph Motor Company between 1963 and 1977. It was introduced on 15 October 1963. It was styled by Giovanni Michelotti.
The Triumph GT6 is a 6-cylinder sports coupé built by Standard-Triumph, based on their popular Triumph Spitfire convertible. Production ran from 1966 to 1973.
The Triumph Herald is a small two-door car introduced by Standard-Triumph of Coventry in 1959 and made through to 1971. The body design was by the Italian stylist Giovanni Michelotti, and the car was offered in saloon, convertible, coupé, estate and van models, with the latter marketed as the Triumph Courier.
The Sunbeam Rapier is an automobile produced by Rootes Group from 1955 until 1976, in two different generations, the "Series" cars and the later (1967–76) fastback shape, part of the "Arrow" range.
The Triumph Vitesse is a compact six-cylinder car built by Standard-Triumph from 1962 to 1971. The car was styled by Giovanni Michelotti, and was available in saloon and convertible variants.
The MGB is a two-door sports car manufactured and marketed from 1962 until 1980 by the British Motor Corporation (BMC), later the Austin-Morris division of British Leyland, as a four-cylinder, soft-top sports car. It was announced and its details first published on 19 September 1962. Variants include the MGB GT three-door 2+2 coupé (1965–1980), the six-cylinder sports car and coupé MGC (1967–1969), and the eight-cylinder 2+2 coupé, the MGB GT V8 (1973–1976).
The MG T-Type is a series of body-on-frame open two-seater sports cars that were produced by MG from 1936 to 1955. Known as the Midget, the series, included the TA, TB, TC, TD, and TF models. Although the design was contemporary in the 1930s, it had grown outdated by the 1950s, and was replaced by the all new MGA in 1955.
The Austin-Healey 100 is a sports car that was built by Austin-Healey from 1953 until 1956.
The Humber Super Snipe is a car which was produced from 1938 to 1967 by British-based manufacturer Humber Limited.
The Aston Martin DB6 is a grand tourer made by British car manufacturer Aston Martin and was produced from September 1965 to January 1971. The "DB" designation is from the initials of David Brown who built up the company from 1947 onwards.
The Triumph TR5 is a sports car built by the Triumph Motor Company in Coventry, England, between August 1967 and September 1968.
Fairthorpe Ltd was a British manufacturer of motorcars, active between 1954 and 1973. Production was in Chalfont St Peter, Buckinghamshire, England between 1954 and 1961, from 1961 to 1973 in Denham, Buckinghamshire.
The Triumph TR3 is a British sports car produced from 1955 to 1962 by the Standard Motor Company of Coventry, England. A traditional open two-seater, the TR3 is an evolution of the company's earlier TR2 model, with greater power and improved braking. Updated variants, popularly but unofficially known as the "TR3A" and "TR3B", entered production in 1957 and 1962 respectively. The TR3 was succeeded by the mechanically similar, Michelotti-styled Triumph TR4.
The Standard Vanguard is a car which was produced by the Standard Motor Company in Coventry, England, from 1947 until 1963.
The Jaguar 420 and its Daimler Sovereign equivalent were introduced at the October 1966 London Motor Show and produced for two years as the ultimate expression of a series of "compact sporting saloons" offered by Jaguar throughout that decade, all of which shared the same wheelbase. Developed from the Jaguar S-Type, the 420 cost around £200 more than that model and effectively ended buyer interest in it, although the S-Type continued to be sold alongside the 420/Sovereign until both were supplanted by the Jaguar XJ6 late in 1968.
The TVR M series is a line of sports cars built by automaker TVR between 1972 and 1979. The series replaced the outgoing TVR Vixen and Tuscan models, and is characterized by a common chassis and shared body style. As with other TVR models before and since, the M-series cars use a front mid-engine, rear-wheel drive layout and body-on-frame construction. The bodies themselves were built from glass-reinforced plastic (GRP). The era of the M series is commonly associated with Martin Lilley who, together with his father, took ownership of the company on 30 November 1965.
The Triumph Fury is a prototype two-door drophead coupé commissioned by the Standard-Triumph Company of Coventry, England. It was the first Triumph sports car built on a unitary construction platform.
The Standard SC engine is a cast-iron overhead valve straight-four engine designed and initially produced by Standard Triumph. Over its production life displacement grew from an initial size of just over 800 cc to nearly 1500 cc. Introduced in the Standard Eight in 1953, it would eventually be used in a wide range of vehicles from Standard, Triumph, and MG.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
