The Triumph TR3 is a British sports car produced between 1955 and 1962 by the Standard Motor Company of Coventry, England. A traditional roadster, the TR3 is an evolution of the company's earlier TR2 model, with greater power and improved braking. Updated variants, popularly but unofficially known as the "TR3A" and "TR3B", entered production in 1957 and 1962 respectively. The TR3 was succeeded by the mechanically similar, Michelotti-styled Triumph TR4.
The rugged ‘sidescreen’ TR, so named for its use of removable plexiglass side curtains, was a sales and motorsport success. With approximately 74,800 TR3s sold across all variants, the model was the company's third best seller in the TR range, behind the TR7 (111,500 units) and TR6 (94,500 units) models.[8]
TR3
Although the base car is an open two-seater, an occasional rear seat and bolt-on steel hard top were available as extras.
The TR3 is powered by a 1,991cc (121.5cuin)Standard wet liner engine. This OHVstraight-four initially produced 95bhp (71kW; 96PS), an increase of 5hp over the TR2 thanks to larger SU H6 carburettors. This was later increased to 100bhp at 5000 rpm[6] by the addition of a "high port" cylinder head and enlarged manifold. The four-speed manual gearbox could be supplemented by an electrically engaged overdrive, controlled by a switch on the dashboard. In 1956, the front brakes were changed from drums to discs, a first for a British series production car.[9]
Front suspension is by double wishbones, manganese bronze trunnions, coil springs and telescopic dampers, with an optional anti-roll bar.
Steering is a worm and peg system. Unlike MGs of the same period, the steering mechanism and linkage have considerable play and friction, which increase with wear.[citation needed]
The rear suspension comprises leaf springs, a beam axle, and lever arm dampers. The (box) frame rails are slung under the axle. Wheels are 15 inches in diameter and 4.5 inches wide (increased from 4 inches after the first few TR2s), with 48-spoke wire wheels optional. Wire wheels were usually painted, either body colour or argent (silver), but matte chrome and bright chrome were also available.
Under most conditions the car is responsive and forgiving, but it has some handling issues.[citation needed] The chassis, which is shared by the TR2, TR3, TR3A, TR3B, and TR4, has limited wheel travel. As a result, on very hard cornering, the inside rear wheel can lift, causing sudden oversteer due to the increased load on the outside rear tyre. This is particularly true with radial tyres; the original TR2/3/3A suspension was built for crossply tyres. The wheel lifting is more sudden than that of other cars, because it is caused by coming to the end of the suspension travel while there is still load on the tyre, so the load on the other (outside) rear wheel is a discontinuous function of cornering load, rather than just changing slope.
The TR3 is a true roadster, designed for sunny weather but with removable rain protection. It has a convertible hood that snaps on and off and removable side curtains, allowing very low doors with padding for the driver's arm to rest on. There are holes in the floor, with rubber plugs, so that the originally supplied jack might be used from inside the car, as in the Jaguar XK120.[clarification needed] The optional heater is poor, and the shut-off valve is under the bonnet.
Some 13,377[10] examples of the original "pre-facelift" TR3 were produced, of which 1,286 were sold within the UK; the rest were exported mainly to the US. As of Q1 2011 there were approximately 826 licensed and 115 SORN TR3/3As registered with the DVLA.[11]
Specifications
Production period – October 1955 to Summer 1957
Original price (basic model) – £950
Suspension – Front: independent by unequal-length double wishbones, coil springs and telescopic dampers. Rear: live axle, half-elliptic springs, lever arm dampers.
Brakes – First 4408 models (1955–56): 10-inch (254mm) drums all around. Remaining 9000 (1956–57): front discs; rear drums.[12]
Tyres - 5.50-15 crossply or 155HR15 Pirelli Cinturato CA67
Factory options – Triumph offered a wide range of options and accessories for both the competition-minded owner and those simply wishing to personalise their vehicle. While many of these items were factory fitments, local dealers supplied some as well. Among these were: overdrive, wire wheels (48-spoke, 60-spoke available from 1959), steel hardtop kit (part No. 900711), occasional rear seat (No. 801264), push-button radio, interior heater, leather upholstery, windscreen washer (No. 553729), cast aluminium sump (No. 502126), aluminium ‘Al-fin’ brake drums (No. 202267 or No. 301590 (9- and 10-inch respectively)), spot and fog lamps (Nos. 501703, 501702), and a continental touring kit (No. 502022, spares for travels in remote regions).[13]
Performance
British auto magazine The Motor tested a hardtop TR3 with overdrive in 1956. The car returned a top speed of 105.3mph (169.5km/h) and could accelerate from 0–60mph (97km/h) in 10.8 seconds. A fuel consumption of 27.1 miles per imperial gallon (10.4L/100km; 22.6mpg‑US) was recorded. The test car cost £1,103 including taxes.[6]
Other figures recorded included:
Speed
Time
0–30mph (48km/h)
3.6 s
0–50mph (80km/h)
7.5 s
0–60mph (97km/h)
10.8 s
0–90mph (140km/h)
28.8 s
Distance
Time
Standing 1⁄4 mile
18.1 s
TR3A
Triumph "TR3A"
In 1957 the TR3 was updated, and this revised model was commonly referred to as the Triumph "TR3A". The cars were not, however, badged as such, and the "TR3A" name was not used officially,[14][15] as is evident from contemporary sales brochures.[16] Changes included a new full-width front grille, exterior door handles, and a lockable boot handle. The previously optional full tool kit became standard equipment. The "TR3A" carried over the standard front disc brakes introduced on later TR3s. The car was known for its superior braking ability with its larger tyres (5.90-15 crossply or 165HR15 Pirelli Cinturato), making it an autocross favourite.
In 1959 other changes were made to the car, including raised stampings under the bonnet and boot hinges and under the door handles, as well as a redesigned rear floor section. In addition, the windscreen was attached with bolts rather than the Dzus fasteners used on the early "A" models.
Although the facelifted TR3 is often referred to as the TR3A, it is badged as "Triumph TR3"
The "TR3A" was built between 1957 and 1962.[17] Total production was 58,236 cars, making it the third best-selling TR in its own right. The TR3A was so successful that the original panel press tooling wore out and had to be replaced. It is estimated that only 9,500 of the original 58,000 built survive today.[citation needed]
The "TR3A" is often seen in vintage and production racing today. Despite being over 50 years old, it is still competitive in Sports Car Club of America (SCCA) E-production class.
In June 1977, Road & Track magazine published an article titled "Driving Impressions: TR3A & TR250" in its 30th anniversary issue. For the "TR3A" it reported a 0–60mph (97km/h) time of 12.0 seconds, power output of 100bhp (75kW) at 4800 rpm, observed kerb weight of 2,090lb (950kg) and fuel consumption of 28 miles per imperial gallon (10L/100km; 23mpg‑US).[18]
TR3B
Triumph "TR3B"
"TR3B" is the unofficial name given to the final version of the Triumph TR3, which was produced in 1962. It was sold concurrently with the TR4, which started production in 1961. The "TR3B" was a special short-production run in response to dealer concerns that the buying public might not welcome the TR4.
The appearance of most "TR3B"s is identical to that of the late US-model "TR3A", with the same wider headlamp rims, wider grille, and door handles. Two series of this version were made. 530 cars with a commission number preceded by TSF were produced, 29 of which were built as Triumph Italias. 2,804 cars were produced with commission numbers preceded by TCF. Both series were partly produced in parallel. The TSF cars, like the last run of TR3As, have a 1991cc engine and a transmission with no synchroniser on first gear. The TCF series has a fully synchronised transmission and a 2138cc version of the Standard wet-liner engine with a 9:1 compression ratio. Fitted with two SU H6 carburettors, it makes 105hp (78kW) at 4,650 rpm and 172N⋅m (127lbf⋅ft) of torque at 3,350 rpm. It gets between 20 and 30 miles per US gallon (11.8 and 7.8L/100km; 24 and 36mpg‑imp). Top speed is limited to about 110mph (177km/h) by the gear ratio, unless fitted with an overdrive unit. An electrically operated Laycockde Normanville Type A overdrive, operating on second, third, and fourth gears, was offered as an option. The car weighs 2,137lb (969kg).
After being introduced to Giovanni Michelotti, Triumph managing director Alick Dick invited the Italian designer to produce a concept car for the British company.[19] Michelotti responded with the Triumph TR3 Speciale, also called the "TR Dream Car".[20]
Built by Vignale on an unmodified TR3 chassis, Michelotti's TR Dream Car incorporated many styling cues from contemporary American practice, including tailfins, a full width grille, lidded headlamps in the tops of the front wings, and a two-tone paint treatment.[19][21] The TR3 Speciale debuted at the Geneva International Motor Show in March 1957.[22] Triumph deemed the car too expensive to put into production, but did give the job of designing the new Triumph Herald to Michelotti.[23][19]
TR3 Beta
The TR3 Beta is a prototype of a modified version of the TR3 with wider than standard front and rear tracks, revised mechanicals, and modified bodywork with wider front and rear wings.[24][25] The project is mentioned several times in the minutes of the meeting of the Standard-Triumph board on 19 September 1960.[26]
Different reasons have been mooted to explain why Triumph created the TR3 Beta. One holds that the Beta predated production of the TR4 chassis, and was solely an attempt to improve the handling of the TR3, with the TR4 a beneficiary of the work done on the Beta.[27] Another points out that work on the TR4 was already underway by 1960, when the Beta project was being discussed.[25] Yet another suggests that the Beta project was begun because Triumph lacked the financial resources needed to tool up to produce the new TR4 body.[24]
The team that produced the Beta was headed by Ray Bates. Work started on the car at Triumph's Capmartin Road (aka Radford) plant, and was later transferred back to their Fletchamstead North site.[27] Team member Ray Henderson took chassis X693, cut it in half lengthwise, and widened the chassis. Bates then engineered changes to allow the wider chassis to be built with existing tooling.[26]
The car was designated as a TR3B, and just two examples were built; the Black Beta and the Red Beta.[27][24][26]
In addition to its wider chassis and modified bodywork, the TR3 Beta shared its fully synchronised gearbox, rack-and-pinion steering, and larger engine with the TR4. By late in the project the Beta had also received a new grille and grille surround, wrap around rear bumpers, and tall stone guards. Use of the Triumph Sabrina engine had been considered for the car.[25][24]
After becoming part of Leyland Motors, the TR4 body shell tooling was funded by the new parent company.[24][25] Work on the Beta was stopped.[26]
As of this writing, one of the Beta prototypes is owned by Neil Revington, and is undergoing a restoration.[28]
Motorsports
1960 Triumph "TR3A" in pit lane
The TR3 was campaigned in races, hill climbs, and rallies across Europe and North America, with several outright, team, and class victories to its credit.
After the 1955 Le Mans disaster, the French government moved to restrict sports car rallying in that country to little more than long distance road races. In response, Triumph competition manager Ken Richardson had steel hard tops bolted to 100 TR3s, homologating the new sports car as a "grand touring" coupé, the GT class still permitted to race on French public roadways.[8] A 'grand touring kit' was made available to customers as an optional extra (part No. 554313).[13]
At the 1959 24 Hours of Le Mans, three extensively modified TR3s, referred to as 'TR3S' models, were run. Resembling the production TR3, the Le Mans cars employed glass fibre body shells, were six inches longer than the production vehicle, and were powered by the prototype 1,985cc (121.1cuin)Triumph Sabrina engine.[31] The Jopp/Stoop TR3S ran as high as seventh place overall before being forced to retire due to mechanical difficulties with just over an hour remaining in the race.[8]
The Triumph Motor Company was a British car and motor manufacturing company in the 19th and 20th centuries. The marque had its origins in 1885 when Siegfried Bettmann of Nuremberg formed S. Bettmann & Co. and started importing bicycles from Europe and selling them under his own trade name in London. The trade name became "Triumph" the following year, and in 1887 Bettmann was joined by a partner, Moritz Schulte, also from Germany. In 1889, the businessmen started producing their own bicycles in Coventry, England.
The Triumph TR6 is a sports car that was built by the Triumph Motor Company of England. While production began several months earlier, the TR6 was officially introduced in January as a 1969 model year vehicle. The last TR6 was produced on the 20th of July 1976. Of the 91,850 TR6s produced, 83,480 were exported, almost all of them to the United States, while only 8,370 were sold in the UK.
The Triumph TR8 is a sports car built by the British Triumph Motor Company from 1978 until 1981. It is an eight-cylinder version of the "wedge-shaped" Triumph TR7 which was designed by Harris Mann and manufactured by British Leyland (BL), through its Jaguar/Rover/Triumph (JRT) division. Because of its outstanding performance, the TR8 was often dubbed the "English Corvette". The majority of TR8s were sold in the United States and Canada.
The Triumph TR4 is a sports car produced by the Triumph Motor Company from 1961 to 1965. Successor to the TR3A, the TR4's chassis and drivetrain are closely related to those of its predecessor, but with an updated body designed by Michelotti.
The Triumph Spitfire is a British sports car manufactured over five production iterations between 1962 and 1980. Styled for Standard-Triumph in 1957 by Italian designer Giovanni Michelotti, the Spitfire was introduced at the London Motor Show in 1962. It was manufactured at the Standard-Triumph Canley works, with approximately 315,000 produced over 18 years.
The Triumph TR7 is a sports car that was manufactured in the United Kingdom from September 1974 to October 1981 by British Leyland Motor Corporation (BLMC), which changed its name to British Leyland (BL) in 1975. The car was launched in the United States in January 1975, with its UK home market debut in May 1976. The UK launch was delayed at least twice because of high demand for the vehicle in the US, with final sales of new TR7s continuing into 1982.
The Triumph TR5 is a sports car built by the Triumph Motor Company in Coventry, England, between August 1967 and September 1968.
The Triumph TR4A is a sports car built by the Triumph Motor Company at its Coventry factory in the United Kingdom between 1965 and 1967. It is an evolution of the Giovanni Michelotti styled TR4, with the TR4's Hotchkiss drive replaced by an independent rear suspension, indicated by an "IRS" badge attached to the car's rear.
The Swallow Doretti is a British sports car built on Swallow's own custom chassis using Triumph TR2 mechanicals, made between 1954 and 1955. It was intended for the US market, as a more refined two-seater than what was available there at that time.
The Morgan Plus 4 is a sports car produced by the Morgan Motor Company. It is a more powerful and, in the case of the earlier cars, a slightly longer version of the company's previous 4/4 model. Plus 4 production ran from 1950 to 1969. It was revived in 1985 and filled the gap between the 4/4 and the Plus 8 until 2000. It was again produced from 2005 until it was replaced in 2020 by the "all new" Plus Four built on a bonded aluminium platform.
The Triumph TR2 is a sports car produced by the Standard Motor Company in the United Kingdom between 1953 and 1955. It was only available in roadster form.
The Daimler SP250 is a sports car built by the Daimler Company, a British manufacturer in Coventry, from 1959 to 1964. It was the last car to be launched by Daimler before its parent company, the Birmingham Small Arms Company (BSA), sold it to Jaguar Cars in 1960.
The Triumph TR range of cars was built between 1953 and 1981 by the Triumph Motor Company in the United Kingdom. Changes from the TR2 to the TR6 were mostly evolutionary, with a change from a live axle to independent rear suspension in 1965 and a change from a four-cylinder engine to a six-cylinder engine in 1967. An all-new TR7, with a unit body, an overhead camshaft four-cylinder engine, and a live rear axle, was introduced in late 1974. The TR8, a development of the TR7 with a Rover V8 engine, was introduced in 1979 and was sold alongside the TR7 until TR production ended.
The Triumph Italia 2000 Coupé was built between 1959 and 1962, during which time 330 cars were produced. Designed by Giovanni Michelotti, the TR3 chassis and mechanical components were supplied by the Triumph Motor Company in the United Kingdom, and built by Alfredo Vignale in Turin, Italy.
The Standard Vanguard is a car which was produced by the Standard Motor Company in Coventry, England, from 1947 until 1963.
Henry George Webster, CBE was a British automotive engineer. He is best known for his work at the Triumph Motor Company throughout the 1950s and 1960s.
The Triumph 20TS was a prototype sports car shown by Standard-Triumph in October 1952 at the London Motor Show. Extensive development of the 20TS led to the introduction of the Triumph TR2 in March 1953 at the Geneva Motor Show, after which the 20TS was unofficially referred to as the Triumph TR1. Only one example of this car was ever made by Triumph.
The Triumph Six Cylinder or Triumph I6 engine is a cast-iron overhead valve straight-six engine produced by Standard Triumph. It is an evolution of the Standard Motor Company's inline-4 Standard Eight, with the addition of two cylinders and a larger displacement.
The Triumph Fury is a prototype two-door drophead coupé commissioned by the Standard-Triumph Company of Coventry, England. It was the first Triumph sports car built on a unitary construction platform.
The Triumph Sabrina engine is an internal combustion engine for automotive applications developed by the Triumph Motor Company division of the Standard Motor Company in England in the late 1950s. It powered Triumph's Le Mans team entries in 1959, 1960, and 1961, and was considered for use in a production road car.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
