Triumph Vitesse

Last updated

Triumph Vitesse
RedTriumphVitesse.JPG
Overview
Manufacturer Standard-Triumph
Production1962–1971
51,212 built
Designer Giovanni Michelotti
Body and chassis
Body style Two-door saloon
Two-door convertible
Three-door estate (by special order)
Layout FR layout
Related Triumph Herald, Triumph GT6
Powertrain
Engine 1596 cc Triumph I6
1998 cc Triumph I6
Transmission Four-speed manual with
Optional overdrive
Dimensions
Wheelbase 91.5 in (2,324 mm) [1]
Length153 in (3,886 mm)
Width60 in (1,524 mm)
Height52.5 in (1,334 mm)
Kerb weight 2,072 lb (940 kg)
Chronology
Successor Triumph Dolomite

The Triumph Vitesse is a compact six-cylinder car built by Standard-Triumph from 1962 to 1971. The car was styled by Giovanni Michelotti, and was available in saloon and convertible variants. [2]

Contents

The Vitesse name was first used by Austin in the 1914 to 1916 Austin 20 (hp) and 30 (hp) Vitesse models. This was followed in 1922 by G. N.(Godfrey & Nash) on their GN Vitesse Cycle-car, and then by Triumph on a car made from 1935-1938.

After the last Triumph Vitesse was made in 1971, the Vitesse name remained unused until 1982. In 1982, Rover began to use the name on their SD1 until 1986. They also used it from 1984-1990 on the SD3 216, and on the Rover 800 from October 1988 - 1991, at which time it was rebodied as the R17 version. The R17 was produced until 1998 as the Rover Vitesse Sport.

Vitesse 6

1965 Triumph Vitesse Saloon 1965 Triumph Vitesse Heritage Motor Centre, Gaydon.jpg
1965 Triumph Vitesse Saloon

The Triumph Vitesse was introduced on May 25, 1962 and reused a name previously used by the pre-Second World War Triumph Motor Company from 1936–38. The engine was an inline 6-cylinder performance version of the Triumph Herald small saloon. The Herald had been introduced in 1959 and was a 2-door car styled by the Italian designer Giovanni Michelotti. Within two years, Triumph began to give thought to a sports saloon based on the Herald and using their 6-cylinder engine. Michelotti was again approached for styling, and he came up with a car that used almost all body panels from the Herald, combined with a new front end with a slanted 4-headlamp design.

Standard-Triumph fitted a 1596 cc version of their traditional straight-6 [3] derived from the engine used in the Standard Vanguard Six, but with a smaller bore diameter of 66.75 mm (2.628 in), compared with the 74.7 mm (2.94 in) bore on the Vanguard, equipped with twin Solex B32PIH semi-downdraught carburetors. These were soon replaced by B321H carburetors due to issues with accelerator pumps. A "seam" on the cylinder block between the third & fourth cylinders reveals the design beginnings of the 803cc  Standard SC engine block, first used in the Standard Eight of 1953. The gearbox was strengthened and upgraded to closer (more sporting) gear ratios, and also offered with optional Laycock De Normanville 'D-type' overdrive with a 20% higher ratio for the top gear (the equivalent change from 3rd to 4th in a standard transmission), giving for more relaxed and economical cruising. Models fitted with overdrive had a chrome badge with "Overdrive" in italic text on the left side of the boot opposite the Vitesse 6 chrome script badge on the right. Synchromesh was present on 2nd, 3rd and 4th gears.

The rear axle was changed to a slightly uprated differential, but retaining the same 4.11:1 ratio and flange sizes as the Herald. Front disc brakes were standard as were larger rear brake drums, and the Herald fuel tank was enlarged, retaining the reserve feature (essentially a curved pickup pipe that could be rotated to dip into the last few centimeters of fuel) of the smaller Herald tank. The front suspension featured uprated springs to cope with the extra weight of the new engine, while the rear suspension, a swing-axle transverse-leaf system, was mostly unchanged from the Herald. The chassis looked outwardly similar to the early Heralds, but in fact was substantially re-designed and strengthened, especially around the differential mountings, improvements which were immediately passed through to Herald production. The dash and instrument panel of the earliest Vitesse was the same as the Herald, with a single speedometer dial featuring fuel and temperature gauge insets. The Vitesse was available in convertibles and saloon forms; a coupé never got beyond the prototype stage. The separate chassis construction of the car meant that no additional strengthening to chassis or body was considered necessary for the convertible model, the only concession being additional door catches to prevent the doors opening during hard cornering.

A handful of Vitesse estates also were assembled to special order at Standard-Triumph's Service Depot at Park Royal in West London.

Triumph Vitesse 3-door estate Vitesse Estate (3782387714).jpg
Triumph Vitesse 3-door estate

The Vitesse received a more luxurious interior compared to the Herald; wooden door capping were added to match the wooden dashboard and the car featured slightly better seats and door trims. Optional extras included a vinyl/fabric 'Britax Weathershield' sunroof on saloon models. Exterior trim was also improved with an elongated stainless steel trim piece which extended further down the body than the Herald, including a Vitesse specific piece of trim rearward of the petrol filler cap and satin-silver anodized alloy bumper capping replacing the white rubber Herald items.

In September 1963 the Vitesse received its first facelift, when the dashboard was revised with a full range of Smith instruments instead of the large single dial from the Herald (large speedometer and cable driven tachometer flanked by smaller 2 inch fuel and temperature gauges). From September 1965, at commission number HB27986, the twin Solex carburettors were replaced by twin Stromberg CD 150 carburetors. Power output increased from the original 70 bhp (52 kW) at 5,000 rpm and torque of 92.5 lb⋅ft (125 N⋅m). There was a claimed increase of 13–14 bhp, and the motoring magazine tested top speed rose to 91 mph (146 km/h), with the 0–80 mph (0–129 km/h) time decreasing from 46.6 seconds to 33.6 seconds.

The Vitesse 6 sold extremely well for Triumph, proving to be the most popular Vitesse sold during the model's lifetime. The car received initial praise for its performance, fuel economy, interior and tight turning circle.

Sports 6

The Vitesse 6 convertible was exported to the US as the left-hand drive Triumph Sports 6 from 1962 until 1964. Original US price (POE East Coast) was $2,499, and it was offered in White, Signal Red or Black. The Vitesse Saloon was never officially imported to the US. Due to its high retail price and competition from cars such as Ford's new Mustang, only 679 were sold before it was withdrawn from the market.

Vitesse 2-Litre

A 1967 Cactus Green Triumph Vitesse 2-Litre convertible (although fitted with mock rostyle wheel trims only introduced on the Mk2; the original 2 litre had hubcaps) Triumph Vitesse Mint Green.jpg
A 1967 Cactus Green Triumph Vitesse 2-Litre convertible (although fitted with mock rostyle wheel trims only introduced on the Mk2; the original 2 litre had hubcaps)

In September 1966, Triumph upgraded the engine to 1998cc, in line with the new Triumph GT6 coupé, and relaunched the Vitesse as the Vitesse 2-Litre. [4] Power was increased to 95 bhp (71 kW), endowing the new car with a claimed 0–60 mph time of just under 12 seconds, and lifting top speed to 104 mph (167 km/h). (The 2-Litre was advertised by Triumph as "The Two Seater Beater"). Other detail modifications for the 2-litre included a stronger clutch, all synchromesh gearbox, larger front brakes, and a stronger differential with a slightly higher 3.89:1 ratio. Wider & stronger 4.5-inch wheel rims were fitted, but radial-ply tyres were still optional at extra cost. There was a satin silver anodized aluminium-alloy cowling above the new reversing light, and badges on the side of the bonnet and in the centre of the grille read 2 litre. The Vitesse boot badge was retained as italic script but lost the 6 of the earlier model - replacing that with the rectangular 2 litre badge and with a chrome strip underlining the Vitesse badge. Cars with overdrive had a separate badge on the cowling above the number plate/reversing light. Inside the car, the seats were improved, with softer (more plush) covering and a better back-rest shape which slightly improved rear-seat knee-room. A new leather-covered three-spoke steering wheel was also added. The Vitesse Mk I was sold until 1968. [4]

Vitesse Mk II

The Vitesse Mark 2 was launched in October 1968 as the final update to the Vitesse range. For the Mark 2, Triumph focused on improvements to the rear suspension by fitting new lower wishbones and Rotoflex half-shaft couplings. This system, also shared with the new GT6 MKII (GT6+ in the US market), and the first GT6 MkIIIs, improved higher speed handing and roadholding. The solid swing axles of the Herald and earlier Vitesses had camber changes of some 15 degrees from the limits of travel. By adding the lower wishbone and the divided drive shaft whilst retaining the transverse leaf spring as the top link, this camber change was reduced to about 5 degrees.

There were other improvements: the engine was tweaked once more to provide 104 bhp (78 kW), cutting the 0–60 mph time to just over 11 seconds and providing a top speed of over 100 mph (160 km/h). The main changes were to the valve timing, to give earlier opening and later closing of the inlet valves compared with the earlier 2-litre engine. (38/78 btdc/atdc for the Mk2 vs 30/60 for the 2 litre). Design changes to the cylinder head allowed for increased inlet valve diameters and better porting. Another major difference in the cylinder head removed the "step" in earlier 1600 and 2 litre incarnations. This meant that in the earlier cars the head studs on the right (manifold) side were short and ended under the manifolds, necessitating unbolting the (hot) manifolds and dropping them back to retorque the studs after a head gasket replacement. The MKII head was full width so all the studs were accessible. The inlet manifolds of the MkII were shorter than the 2 litre to keep inlet tract length the same. The Stromberg carburetors were also changed from 150 CD to 150 CDS, the S referring to the use of a spring between the dashpot cover and piston.

The exterior featured a new grille with 3 sets of horizontal elements that were also used (in longer form) in the Herald 13/60, Rostyle wheel trims and silver painted steel rear panel (described by Triumph as "ceramic"). The interior was upgraded once more in order to share parts with the new Herald 13/60, though the Vitesse included a tachometer and larger ashtray. A new colour range was offered for the Mark 2 models. The aluminium cowling above the reversing light gained an oblong chromed VITESSE badge, and the separate chromed Mazak TRIUMPH letters on the bonnet and the boot lid were also deleted. The badges on the bonnet sides were changed to read Mk2 instead of 2 litre. Cars with overdrive had a small badge that fitted below the new rectangular Triumph boot badge.

The Vitesse continued to sell well until its discontinuation in July 1971, seven months before being replaced by the Triumph Dolomite. [5]

Production figures

Triumph Vitesse Triumph Vitesse .jpg
Triumph Vitesse

Related Research Articles

<span class="mw-page-title-main">Triumph Stag</span> Motor vehicle

The Triumph Stag is a 2+2 sports tourer which was sold between 1970 and 1978 by the British Triumph Motor Company, styled by Italian designer Giovanni Michelotti.

<span class="mw-page-title-main">Triumph Dolomite</span> Motor vehicle

The Triumph Dolomite small saloon car was produced by the Triumph Motor Company division of the British Leyland Corporation in Canley, Coventry between October 1972 and August 1980.

<span class="mw-page-title-main">Ford Zephyr</span> Motor vehicle

The Ford Zephyr is an executive car manufactured by Ford of Britain from 1950 until 1972. The Zephyr and its luxury variants, the Ford Zodiac and Ford Executive, were the largest passenger cars in the British Ford range from 1950 until their replacement by the Consul and Granada models in 1972.

<span class="mw-page-title-main">Triumph Spitfire</span> Motor vehicle

The Triumph Spitfire is a British sports car manufactured over five production iterations between 1962 and 1980. Styled for Standard-Triumph in 1957 by Italian designer Giovanni Michelotti, the Spitfire was introduced at the London Motor Show in 1962. It was manufactured at the Standard-Triumph Canley works, with approximately 315,000 produced over 18 years.

<span class="mw-page-title-main">Vauxhall Carlton</span> Motor vehicle

The Vauxhall Carlton is a series of large family car/executive car sold in two distinct generations by the Vauxhall division of GM Europe between 1978 and 1994. The Carlton was based on the Opel Rekord E (Mk.1) and Omega A (Mk.2).

<span class="mw-page-title-main">Triumph 2000</span> Motor vehicle

The Triumph 2000 is a mid-sized, rear wheel drive automobile which was produced in Coventry by the Triumph Motor Company between 1963 and 1977. It was introduced on 15 October 1963. It was styled by Giovanni Michelotti.

<span class="mw-page-title-main">Triumph GT6</span> Motor vehicle

The Triumph GT6 is a 6-cylinder sports coupé built by Standard-Triumph, based on their popular Triumph Spitfire convertible. Production ran from 1966 to 1973.

<span class="mw-page-title-main">Triumph Herald</span> Motor vehicle

The Triumph Herald is a small two-door car introduced by Standard-Triumph of Coventry in 1959 and made through to 1971. The body design was by the Italian stylist Giovanni Michelotti, and the car was offered in saloon, convertible, coupé, estate and van models, with the latter marketed as the Triumph Courier.

<span class="mw-page-title-main">Sunbeam Rapier</span> Motor vehicle

The Sunbeam Rapier is an automobile produced by Rootes Group from 1955 until 1976, in two different generations, the "Series" cars and the later (1967–76) fastback shape, part of the "Arrow" range.

<span class="mw-page-title-main">Vauxhall Cresta</span> Motor vehicle

The Vauxhall Cresta is a British automobile which was produced by Vauxhall from 1954 to 1972. The Cresta was introduced in 1954 as an upmarket version of the Vauxhall Velox, itself a six-cylinder version of the Vauxhall Wyvern. The Cresta models were the E (1954–1957), PA (1957–1962), PB (1962–1965) and PC (1965–1972). The Viscount (1966–1972) was an upmarket Cresta PC.

<span class="mw-page-title-main">Triumph TR4A</span> Motor vehicle

The Triumph TR4A is a sports car built by the Triumph Motor Company at its Coventry factory in the United Kingdom between 1965 and 1967. It is an evolution of the Giovanni Michelotti styled TR4, with the TR4's Hotchkiss drive replaced by an independent rear suspension, indicated by an "IRS" badge attached to the car's rear.

<span class="mw-page-title-main">Jaguar Mark 2</span> Motor vehicle

The Jaguar Mark 2 is a mid-sized luxury sports saloon built from late 1959 to 1967 by Jaguar in Coventry, England. The previous Jaguar 2.4 Litre and 3.4 Litre models made between 1955 and 1959 are identified as Mark 1 Jaguars.

<span class="mw-page-title-main">Fiat 2300</span> Motor vehicle

The Fiat 2300 is a six-cylinder executive car which was produced by Italian automotive manufacturer Fiat between 1961 and 1968. The 2300 was made as saloon, estate car and coupé. The 2300 saloon is noteworthy as in 1966 it became the first Fiat model to be available with an automatic transmission.

<span class="mw-page-title-main">Bond Equipe</span> Motor vehicle

The Bond Equipe is an English 2+2 sports car, manufactured by Bond Cars Ltd from 1963 to 1970. It was the first 4-wheeled vehicle from Bond Cars.

<span class="mw-page-title-main">Standard Vanguard</span> Motor vehicle made in England

The Standard Vanguard is a car which was produced by the Standard Motor Company in Coventry, England, from 1947 until 1963.

<span class="mw-page-title-main">Hillman Super Minx</span> Motor vehicle

The Hillman Super Minx is a family car which was produced by Hillman from 1961 to 1967. It was a slightly larger version of the Hillman Minx, from the period when the long-running Minx nameplate was applied to the "Audax" series of designs.

<span class="mw-page-title-main">Jaguar Mark VIII</span> Motor vehicle

The Jaguar Mark VIII is a luxury four-door automobile introduced by the Jaguar company of Coventry at the 1956 London Motor Show.

<span class="mw-page-title-main">Sunbeam-Talbot 90</span> Motor vehicle

The Sunbeam-Talbot 90 is an automobile which was produced and built by Sunbeam-Talbot from 1948 to 1954 and continued as the Sunbeam Mk III from 1954 to 1957.

<span class="mw-page-title-main">Triumph I6</span> Reciprocating internal combustion engine

The Triumph Six Cylinder or Triumph I6 engine is a cast-iron overhead valve straight-six engine produced by Standard Triumph. It is an evolution of the Standard Motor Company's inline-4 Standard Eight, with the addition of two cylinders and a larger displacement.

<span class="mw-page-title-main">Triumph Fury</span> Two-door prototype drophead coupé

The Triumph Fury is a prototype two-door drophead coupé commissioned by the Standard-Triumph Company of Coventry, England. It was the first Triumph sports car built on a unitary construction platform.

References

  1. Cardew, Basil (1966). Daily Express Review of the 1966 Motor Show. London: Beaverbrook Newspapers.
  2. "All BUYERS GUIDEs 02" (PDF). The Triumph Sports Six Club. Retrieved 29 April 2022.
  3. "Triumph Vitesse 1600". The Triumph Sports Six Club. Retrieved 29 April 2022.
  4. 1 2 "Triumph Vitesse 2-Litre MkI". The Triumph Sports Six Club. Retrieved 29 April 2022.
  5. Motoring Which? magazine, July 1973

Further reading