The car, announced in July 1947, was completely new, with no resemblance to previous models. Designed in 1945,[2] it was Standard's first post-World War II car and intended for export around the world. It was also the first model to carry the new Standard badge, which was a heavily stylised representation of the wings of a griffin.[3]
In the wake of World War II, many potential customers in the UK and in English-speaking export markets had recently experienced several years of military or naval service, and therefore a car name related to the Royal Navy carried a greater resonance than it would for later generations. The name of the Standard Vanguard recalled HMS Vanguard, the last of the Royal Navy's battleships, launched in 1944 amid much media attention; permission to use the name involved Standard in extensive negotiations with senior Royal Navy personnel.
The Vanguard was first exhibited to the public at the Brussels Motor Show in February 1948.[4] It began to come off the assembly lines in the middle of 1948 but all production was allotted to the export trade.[5] An estate car and a utility pick up version were announced in September, and then a 12 cwt delivery van.[6] Aprons were fitted over the Vanguard's rear wheels from September 1949.[7]
In 1950,[8] the Vanguard and the Triumph Renown were the first cars to be fitted with a Laycock de Normanvilleoverdrive. The Laycock overdrive operated on the second and third gears of the three-speed transmission, creating, in effect, a five-speed gearbox.
The car used a conventional chassis on which was mounted the slab sided body. Suspension was independent at the front with coil springs, and a live axle and leaf springs at the rear. Front and rear anti-roll bars were fitted. The brakes were cable driven with 9-inch (228mm) drums all round, and to make the most of the interior space a column gear change was used initially on the right of the steering wheel then later on the left.[citation needed]
Engine
The same wet liner engine was used throughout the range until the advent of the Six model in 1960, and was an overhead-valve unit of 85mm (3.3in) bore and 92mm (3.6in) stroke with single Solex downdraught carburettor. The compression ratio was 6.7:1. Wet cylinder liners were fitted. The engine was essentially the same as that made by Standard for the Ferguson TE20 tractor, with some changes for automobile use.[citation needed]
Transmission
At first, the transmission included a three-speed gearbox with synchromesh on all forward ratios, controlled using a column-mounted lever. The option of Laycock-de-Normanville overdrive was announced at the end of 1949 and became available in June 1950, priced for UK buyers at slightly under £45 including purchase tax.[12] Laycock overdrives were cable operated on top gear until 1954 when an electric solenoid was added.[citation needed]
A car tested by The Motor magazine in 1949 had a top speed of 78.7mph (126.7km/h) and could accelerate from 0–60mph (97km/h) in 21.5 seconds. A fuel consumption of 22.9 miles per imperial gallon (12.3L/100km; 19.1mpg‑US) was recorded. The test car cost £671 including taxes.[11]
Commercial
In line with the post-war British export drive, virtually the total output was exported for the first two years of production and only in 1950 did significant home market deliveries start. The Vanguard was intended to achieve export sales, with a particular focus on Australia. During the immediate post-war period, cars were in short supply, creating a "seller's market". Restricted availability of the Vanguard helped attract willing buyers.
Closer to home, in the slowly recovering West German market the Standard Vanguard recorded 405 sales in 1950, making it the country's third most popular imported automobile, in a list otherwise featuring much smaller cars from French and Italian manufacturers. In fact, the Vanguard sales in 1950 accounted for more than 70% of the British cars sold in West Germany that year, customers of other UK manufacturers having reportedly been caught out in the late 1940s by the lack of a dealer network and difficulties in obtaining replacement parts.[13]
Standard Vanguard Phase I Saloon
Standard Vanguard Phase I Estate
Standard Vanguard Phase I Coupe Utility
Standard Vanguard Phase I Van
Standard Vanguard Phase I Convertible by Imperia of Belgium
Phase IA - 1952 facelift
The body was updated in 1952 with a lowered bonnet line, a wider rear window and a new grille featuring a wide horizontal chrome bar in place of the narrow, more closely packed slats of the original grille.[14] This became known as the Phase 1A.[10]
The Swiss importer for the Vanguard was an energetic firm called AMAG, which later took on the Swiss Volkswagen franchise. AMAG themselves assembled the Swiss market Phase I Vanguards,[14] and it was at the Geneva Motor Show in March 1953[16] that an extensive re-design was unveiled: the Phase II Vanguard was of a contemporary Pontonthree-box "notch-back" design. Boot/trunk capacity increased by 50% in comparison to that of the Phase I, and visibility was improved with a further enlarged rear window.[14] A new, extended, grille now encompassed the parking lights.[10]
Mechanically there were few changes, but the clutch changed from cable to hydraulic operation and the engine compression ratio increased to 7.2:1. The previously fitted anti-roll bar was no longer used. Wider 6.00x16 tyres were fitted to improve road holding.[citation needed]
A car that was tested by The Motor magazine, without the optional overdrive, had a top speed of 80mph (130km/h) and could accelerate from 0–60mph (97km/h) in 19.9 seconds. A fuel consumption of 23.5 miles per imperial gallon (12.0L/100km; 19.6mpg‑US) was recorded.[16]
In February 1954 Standard became the first British car maker to offer a diesel engine as a factory fitted option.[17] The chassis was stiffened to take the weight of the heavier engine and performance suffered with 65mph (105km/h) about the top speed. Like the petrol engines, the diesel was a Standard-built "20C" engine developed for the Ferguson tractor. The diesels fitted to the tractor were restricted to 2200 rpm and developed 25 horsepower (19kW), but road-going engines in Vanguards had no limiter and so produced 60 horsepower (45kW) at 3800 rpm. However, they retained the tractor's "Ki-Gass", de-compressor and over-fuelling systems, all of which had to be manually operated when starting the engine from cold. 1,973 diesel Vanguards were made.[citation needed]
In 1954 The Motor magazine tested the diesel version and recorded a top speed of 66.2mph (106.5km/h) acceleration from 0–50mph (80km/h) in 31.6 seconds and a fuel consumption of 37.5 miles per imperial gallon (7.5L/100km; 31.2mpg‑US). The test car, which had overdrive, cost £1,099 including taxes.[18]
For 1955, the Australian-built coupé utility was given a re-styled tail which resulted in extra room in the cargo area.[10] It also featured a new full-width rear window and improved cabin features.[10] As the coupe utility variant of the Phase III style was not yet available, an updated Phase II utility was offered in 1956 with a mesh grille, two-tone paint and new interior trim.[10]
Standard Vanguard Phase II Saloon
Standard Vanguard Phase II Estate
Standard Vanguard Phase II Utility
Assembly at AB Nyköpings Automobilfabrik in Sweden
Vanguard Phase III & Vanguard Sportsman
Motor vehicle
Standard Vanguard Phase III Standard Vanguard Sportsman
Standard Vanguard Phase III Saloon
Overview
Production
1955–1958 (Phase III) 37,194 produced 1956–1957 (Sportsman) 901 produced[17]
The Phase III, released to the market for the mid-October 1955 British International Motor Show,[20] was a radical change with the elimination of the separate chassis. There was an overlap in availability of the old model with the Phase II estate continuing into 1956.
UK fuel was no longer restricted to the 72 octane "Pool petrol" of the 1940s and early 1950s, and with the modest increases in available octane levels, the Vanguard's compression ratio was increased to 7.0:1. The 2,088cc (127.4cuin) engine with its single Solex downdraught carburettor now produced 68bhp (51kW; 69PS).
The front suspension was independent, using coil springs, and was bolted to a substantial sub-frame which also carried the recirculating ball steering gear. Semi-elliptic leaf springs were used on the rear axle. Lockheed hydraulic brakes with 9in (229mm) drums were fitted front and rear. The three-speed gearbox had a column change and the optional overdrive was operated by a switch on the steering column. A four-speed floor change became an option.[citation needed]
The new body was lower and had an increased glass area, making it look much more modern, and the old two-piece flat windscreen gave way to a one-piece curved design. The wheelbase increased by 8in (203mm), giving much better passenger accommodation. A heater was now a standard fitting. Bench seats were fitted in front and rear with folding centre arm rests. They were covered in Vynide, with leather available as an option.[citation needed]
The car was lighter than the superseded model, and the gearing was changed to deliver better economy with performance virtually unchanged.[citation needed]
A car with overdrive was tested by the British magazine The Motor in 1956. It had a top speed of 83.7mph (134.7km/h), could accelerate from 0–60mph (97km/h) in 21.7 seconds and had a fuel consumption of 25.9 miles per imperial gallon (10.9L/100km; 21.6mpg‑US). The test car cost £998 including taxes.[19]
For 1957, the Australian-produced Phase III was given a facelift with a new mesh grille.[10] In addition the saloon now sported fins on the rear guards.[10]
Vanguard Sportsman
A performance model, the Vanguard Sportsman, intended to be badged as the Triumph Renown until shortly before launch, was announced in August 1956[21] with a tuned 90bhp (67kW)[21] engine having similar features to the Triumph TR3 sports car. These included an increased compression ratio to 8.0:1, twin SU carburettors,[22] and improved pistons. However, the Sportsman's inlet manifold and carburettors sat at a different angle from those of the TR3,[citation needed] and its engine had the same 85mm bore as the Vanguard's,[22] rather than the 83mm bore of the TR3.[23] The final-drive ratio was lowered to 4.55:1 to give better acceleration, and larger 10in (254mm) drums fitted to the brakes. The standard version had a bench front seat but separate seats were an option.[citation needed]
Although sharing the same basic body shell with the other Vanguard variations, the Sportsman had design variations, including a squarer front grille, which gave the car a slightly higher, squarer appearance than the standard models.[21]
Just 901 examples of the Sportsman model were made up to 1958.[17] Sportsmans then became available to special order, and around another fifty (mostly estate cars) were built between 1958 and 1960. A small number were built before the Vignale makeover in 1958. Popular Classics magazine's test of a Sportsman in 1994 stated that a total of 962 were built.[21]
A Sportsman with overdrive was tested by The Motor in 1956 and it recorded a top speed of 90.7mph (146km/h), acceleration from 0–60mph (97km/h) in 19.2 seconds and a fuel consumption of 25.6 miles per imperial gallon (11.0L/100km; 21.3mpg‑US). The test car cost £1231 including taxes.[24]
Standard Vanguard Phase III Saloon
Standard Vanguard Sportsman
Standard Ensign and Ensign De Luxe
Motor vehicle
Standard Ensign Standard Ensign De Luxe
1960 Standard Ensign Saloon
Overview
Production
1957 to 1961 (Ensign) 18,852 produced 1962 to 1963 (Ensign De Luxe) 2,318 produced[17]
A basic model, the Standard Ensign, with 1670cc engine,[25] was announced in October 1957 restyled by Michelotti.[citation needed] The Ensign shared its body with the Vanguard Series III, but had a cheapened specification in various respects, including a mesh front grille and a simplified instrument panel and dashboard. Despite the generally lower specification, the Ensign was the first Vanguard-based car to have a four-speed gearbox. The gear lever was moved from the column to the floor, and overdrive was optional. Many were bought for company fleets and for the armed forces.[26] Production ceased in 1961 with 18,852 examples having been produced.[17] Production included 901 Mk II versions, produced only in 1961.[17]
An Ensign De Luxe version followed in 1962 and 1963 with a larger 2138cc engine. Unlike the smaller-engined original version, the De Luxe was also available as an estate car.[22]
A 1670cc Ensign was tested by the British magazine The Motor in 1958. It recorded a top speed of 77.6mph (124.9km/h), acceleration from 0–60mph (97km/h) in 24.4 seconds and a fuel consumption of 28.5 miles per imperial gallon (9.9L/100km; 23.7mpg‑US). The test car cost £899 including taxes of £300.[27]
In January 1960 a diesel engined Ensign was announced, featuring the compact "P4C" 1.6litre four-cylinder engine produced by specialists Perkins of Peterborough.[28] Claimed output was 43bhp (32kW), with fuel consumption stated as "about 50 mpg" (5.6 L/100km; 42 mpg-US).[28]
A face-lift of the Phase III was designed by Italian stylist Giovanni Michelotti and coach-builders Vignale in 1958, and was introduced at the October 1958 Earls Court Motor Show.[31] The windscreen and rear window were deeper, and there was a revised grill and trim. A floor change four-speed manual gearbox was now fitted, and the provision of a three-speed gear box with column change offered as an option. An overdrive was also offered an option, as was an automatic. One automatic car is known to have survived - there may be others.[citation needed]
The car had front and rear bench seats, which were covered, as standard, in Vynide. Leather was an option on the home market and cloth for exported models. A heater and (unusual for the time) electric windscreen washers were factory fitted, although a radio remained an option.[citation needed]
A Vignale with overdrive was tested by the British magazine The Motor in 1959. It recorded a top speed of 82.8mph (133.3km/h), acceleration from 0–60mph (97km/h) in 20.8 seconds and a fuel consumption of 28.0 miles per imperial gallon (10.1L/100km; 23.3mpg‑US). The test car cost £1147 including taxes of £383.[32]
Introduced at the end of 1960, the last of the Vanguards featured a six-cylinder 1,998 cc engine with push-rod overhead valves: this was the engine subsequently installed in the Triumph 2000. The compression ratio was 8.0:1, and twin Solex carburettors were fitted giving an output of 80bhp (60kW) at 4500rpm.[33] Externally the only differences from the Vignale were the badging but the interior was updated.
Australian production included coupe utility and van variants.[10] Early in the model run the rear lights of the coupe utility were changed from a vertical to a horizontal layout with a different rear body side panel.[10]
A Vanguard Six was tested by the British magazine The Motor in 1960. It recorded a top speed of 87.2mph (140.3km/h), acceleration from 0–60mph (97km/h) in 17.0 seconds and a fuel consumption of 24.9 miles per imperial gallon (11.3L/100km; 20.7mpg‑US). The test car cost £1021 including taxes of £301.[33]
Standard Vanguard Six Saloon
Standard Vanguard Six Estate
Standard Vanguard Six Utility (later version with horizontal rear lights)
Replacement and end of Standard
Leyland Motors took over Standard-Triumph in 1960 and the prototype Triumph 2000 progressed with new money, the engine being used by the Vanguard Six from 1961 to early 1963. The six was lighter than the old four and was a development based on the Standard Ten unit.[citation needed]
Both the Ensign and the Vanguard were replaced in 1963 by the Triumph 2000, and the Standard name disappeared from the British market after 60 years.
In 1950, the Australian subsidiary of the Standard Motor Company introduced a coupé utility version of the Vanguard Phase I. It was fitted with the same 2088cc four-cylinder engine as used in the saloon.[35] Utility versions of the Vanguard were produced in Australia over the following years,[36] with production ending in 1964.[37]
The Vanguard Utility was sold in the UK as a pickup truck. The main purchaser was the Royal Air Force, which had them in Phase I and II form. The Phase II commercials remained available until 1958, when they were replaced by the Phase 3. Around 50 phase 3 pickups went to Welsh Water and the workshop manual pictures a pickup with a body by Awson. A gown van and a breakdown tender are shown in the brochure.[citation needed]
Sales in the UK were modest, mostly due to stiff competition from the British Motor Corporation and from Standard's other commercial vehicles including the 5cwt and later 7cwt vehicles. With the discontinuation of the Vanguard Utility, the only commercial vehicle produced by the company was the Standard Atlas, and so that was the Vanguard Utility's replacement, but they did share some common parts.[citation needed]
Corgi Toys included a model of the Phase III saloon in their range from 1957 to 1961 as model No 207.[38] Additionally, a Phase III saloon presented as a Royal Air Force Staff Car was available from 1958 to 1962 as model No 352.[39]
↑ (Australia)Advertisement for Standard Vanguard (Vignale) utility, Australian Motor Industries Ltd, Australian Motor Manual (magazine), 1 August 1960, page 29
↑ "Standard 1959". www.classiccarcatalogue.com. Archived from the original on 28 September 2013. Retrieved 26 October 2011.
↑ "The Standard Motor Company. Lord Tedder Describes Expansion And Development". The Times. No.54316. London. 24 November 1958. p.14.
↑ "The Standard Vignale Vanguard". The Motor. 114 (2963). 7 January 1959.
1 2 3 4 5 "The Standard Vanguard Six". The Motor. 118 (3055). 7 December 1960.
The Ford Anglia is a small family car that was designed and manufactured by Ford UK. It is related to the Ford Prefect and the later Ford Popular. The Anglia name was applied to various models between 1939 and 1967. In total, 1,594,486 Anglias were produced. It was replaced by the Ford Escort.
The Ford Prefect is a line of British cars which was produced by Ford UK between 1938 and 1961 as an upmarket version of the Ford Popular and Ford Anglia small family cars. It was introduced in October 1938 and remained in production until 1941. Returning to the market in 1945, it was offered until 1961. The car progressed in 1953 from its original perpendicular or "sit-up-and-beg" style to a more modern three-box structure. Some versions were also built and sold by Ford Australia.
The Ford Zephyr is an executive car manufactured by Ford of Britain from 1950 until 1972. The Zephyr and its luxury variants, the Ford Zodiac and Ford Executive, were the largest passenger cars in the British Ford range from 1950 until their replacement by the Consul and Granada models in 1972.
The Peugeot 404 is a large family car produced by French automobile manufacturer Peugeot from 1960 to 1975. A truck body style variant was marketed until 1988. Styled by Pininfarina, the 404 was offered initially as a saloon, estate, and pickup. A convertible was added in 1962, and a coupé in 1963. The 404 was fitted with a 1.6 litre petrol engine, with either a Solex carburetor or Kugelfischer mechanical fuel injection or a 1.9 litre diesel engine available as options. Introduced at the Paris Motor Show as an option was the inclusion of a 3-speed ZF automatic transmission, similar to the unit already offered on certain BMW models, as an alternative to the standard column-mounted manual unit.
The Singer Gazelle name has been applied to two generations of motor cars from the British manufacturer Singer. It was positioned between the basic Hillman range and the more sporting Sunbeam versions.
The Sunbeam Rapier is an automobile produced by Rootes Group from 1955 until 1976, in two different generations, the "Series" cars and the later (1967–76) fastback shape, part of the "Arrow" range.
The Lancia Flavia is an executive car produced by Italian automaker Lancia from 1961 to 1971.
The Riley 4 / Sixty Eight and Riley 4 / Seventy Two are cars produced by BMC from 1959 to 1969, under the Riley marque. They are closely related to the Pinin Farina-designed MG Magnette Mark III and Wolseley 15/60 and the simpler Austin A55 Cambridge Mark II, Morris Oxford V pair, sharing the MG's rear styling and engine. This Riley was the most expensive car in that series.
The Austin Cambridge is a medium-sized motor car range produced by the Austin Motor Company, in several generations, from September 1954 through to 1971 as cars and to 1973 as light commercials. It replaced the A40 Somerset and was entirely new, with modern unibody construction. The range had two basic body styles with the A40, A50, and early A55 using a traditional rounded shape and later A55 Mark IIs and A60s using Pininfarina styling.
The Austin Westminster series are large saloon and estate cars that were sold by the British manufacturer Austin from 1954, replacing the A70 Hereford. The Westminster line was produced as the A90, A95, A99, A105, and A110 until 1968 when the new Austin 3-Litre took its place. Essentially badge-engineered versions of the Farina Westminsters were also produced using the premium Wolseley and Vanden Plas marques. 101,634 Westminsters were built.
The Humber Super Snipe is a car which was produced from 1938 to 1967 by British-based manufacturer Humber Limited.
The Morris Isis name was first briefly used by Morris Motors Limited on a 6-cylinder car made from 1929 until 1931. It was resurrected on a new 6-cylinder midsize car from the British Motor Corporation in the 1950s to replace the Morris Six MS.
The Rover P4 series is a group of mid-size luxury saloon cars produced by the Rover Company from 1949 until 1964. They were designed by Gordon Bashford.
The Armstrong Siddeley Sapphire is a large automobile which was produced by the British company, Armstrong Siddeley Motors Limited, from 1952 to 1960.
The Fiat 1400 and Fiat 1900 are passenger cars produced by Italian automotive manufacturer Fiat from 1950 to 1958 and from 1952 to 1959 respectively. The two models shared body and platform, but while the 1.4-litre 1400 was Fiat's intermediate offering, the upmarket 1900 had an enlarged 1.9-litre engine and more luxurious trim and equipment, to serve as flagship in the manufacturer's range.
The Humber Hawk is a four-cylinder automobile manufactured by British-based maunufacturer Humber Limited from 1945 to 1967.
The Standard Ten was a model name given to several small cars produced by the British Standard Motor Company between 1906 and 1961. The name was a reference to the car's fiscal horsepower or tax horsepower, a function of the surface area of the pistons. This system quickly became obsolete as an estimate of the power produced by the engine, but it continued to be relevant as a way to classify cars for tax purposes. Like other manufacturers, Standard continued to use the name to define the approximate size of their 'Ten' model long after the origins of the name had, in Britain, become inapplicable.
The Vauxhall Velox is a six-cylinder executive car which was produced by Vauxhall from 1948 to 1965. The Velox was a large family car, directly competing in the UK with the contemporary six-cylinder Ford Zephyr, and to a slightly lesser extent, with the A90, A95, and A110 Austin Westminster models.
The Sunbeam-Talbot 90 is an automobile which was produced and built by Sunbeam-Talbot from 1948 to 1954 and continued as the Sunbeam Mk III from 1954 to 1957.
The Triumph Renown is strictly the name given to the Triumph's large saloon car made from 1949 to 1954 but it is, in reality, part of a three-car series of the 1800, 2000 and Renown models. Together with the Triumph Roadster, they were the first vehicles to carry the Triumph badge following the company's takeover by the Standard Motor Company.
References
Allen, Michael (1985). British Family Cars of the Fifties. Haynes Publishing. ISBN0-85429-471-6.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
