On a ship, the fire room, or FR or boiler room or stokehold, referred to the space, or spaces, of a vessel where water was brought to a boil. The steam was then transmitted to a separate engine room, often (but not always) located immediately aft, where it was utilized to power the vessel.[1][failed verification] To increase the safety and damage survivability of a vessel, the machinery necessary for operations may be segregated into various spaces, the fire room was one of these spaces, and was among the largest physical compartment of the machinery space. On some ships, the space comprised more than one fire room, such as forward and aft, or port or starboard fire rooms, or may be simply numbered. Each room was connected to a flue, exhausting into a stack ventilating smoke.
By their nature, fire rooms were less complex than their allied engine room and were normally supervised by less senior personnel.
On a large percentage of vessels, ships and boats, the fire room was located near the bottom, and at the rear, or aft, end of the vessel, and usually comprised few compartments. This design maximized the cargo carrying capacity of the vessel. The fire room on some ships was situated amid-ships, especially on vessels built from the 1880s to the 1990s.
Equipment
Vessels typically contained several engines for different purposes. Main, or propulsion engines are used to turn the ship's propeller and move the ship through the water. The fire room got its name from the days when ships burned coal to heat steam to drive the steam engines or turbines; the room was where the stokers spent their days shoveling coal continuously onto the grates under the boiler; poor men could sometimes pay for a trip across the Atlantic by signing on to work as a stoker for a one way trip, laboring in exchange for a temporary place on the crew. Later heavy fuel oil came into use, first combined with coal, then alone, as the petroleum industry developed, and the cleaner, easier to transport, load and burn liquid was found to be far superior once the appropriate logistical network was set up. With coal power, there was a mechanism for removing ash from the grates, as they would build up rapidly over time (the lighter fly ash would be drawn up the stack with the smoke).[2]
On a steamship, power for both electricity and propulsion is provided by one or more large boilers giving rise to the alternate name boiler room. The latter name was preferred in the British Navy, among others. High pressure steam from the boiler is piped to the engine room to drive reciprocating engines or turbines for propulsion, and turbo generators for electricity. When cruising, it was normal for a naval vessel to damp the fires on up to two-thirds of their boilers, and use the steam from only a few boilers in one or two fire rooms to power the engines at low power. When higher speeds were required, more boilers would be brought on line (they were rarely extinguished entirely, as re-lighting a boiler was time-consuming). In rare occasions, when flank speed was called for, all boilers would be burning at once, generating a great deal of steam for high-speed operation, but at a very inefficient rate of coal consumption. Merchant vessels had much less need for high speed, so they would generally be satisfied with far fewer boilers, and much lower maximum speeds (and even then they would often save on fuel by not using all of the boilers, and traveling at a sedate 4-5 knots).
Naval ships typically were able to generate a large volume of smoke by changing the fuel mix. Prior to the heavy use of radar, a smoke screen could be used to mask the movement of ships (although smoke screens produced by smoke generators were also used). Coal in particular produced a large amount of black smoke, depending on the grade of coal; generally, the smallest amount of smoke was the most desirable, as it made the vessel harder to spot on the horizon.
Damage control
Damage control was enhanced by the separation of the fire and engine rooms. In the event of damage to its associated engine room, steam could be transmitted to another engine room. In turn, an engine room could still operate though its associated fire room had become inoperative.
Two engineering advances resulted in the disappearance of the fire room in the early 1990s. The first was the movement by naval shipbuilding to nuclear-powered vessels. If a room containing nuclear material was subjected to damage, it was assumed that the event would likely result in abandonment of the ship regardless of the separation of rooms.
The second was the adoption of gas turbines in place of oil-fired boilers for all other navy ships. These powered engines directly and needed no boilers.
Safety
Fire precautions
Fire rooms were hot, most often very dirty, and potentially dangerous. The presence of flammablefuel meant that a fire hazard existed in the fire room, which was monitored continuously by the ship's engineering staff and various monitoring systems.
Ventilation
Fire rooms employed some means of providing air for the operation of the flame to ignite the oil and associated ventilation. Only spot ventilation was practical to keep personnel cool.[3] This would require an unrestricted hull opening of the same size as the intake area of the engine itself assuming the hull opening is in the fire room itself.
Forced draft fire rooms were used until World War II. These required that personnel enter through an air lock to maintain the pressure. These were abandoned when the forced draft occasionally failed and blowback occurred killing fire room personnel.
Commonly, screens were placed over openings reducing airflow by approximately 50% so the opening area was increased appropriately. The requirement for general ventilation and the requirement for sufficient combustion air are quite different. A typical arrangement might be to make the opening large enough to provide intake air plus 1,000 cubic feet (28m3) per Minute (CFM) for additional ventilation. Engines pull sufficient air into the fire room for their own operation. However, additional airflow for ventilation usually requires intake and exhaust blowers.
Staffing requirements
When fired up, there were personnel assignments specified underway, as well as in port. For example, for an Iowa-classbattleship, in normal steaming four boilers were operated. This was sufficient to power the ships at speeds up to 27 knots (50km/h). For higher speeds, all eight boilers were lit. Each operating boiler required a minimum of four trained operators on watch: a boiler supervisor (BTOW), a superheater burnerman and saturated burnerman to control the steam temperature and pressure and a checkman, who monitored and controlled the water level in the steam drum. In addition, there was a fireroom messenger and a lower level pumpman on duty whenever the fireroom was steaming.[4]
An engine department or engineering department is an organizational unit aboard a ship that is responsible for the operation, maintenance, and repair of the propulsion systems and the support systems for crew, passengers, and cargo. These include the ship engine, fuel oil, lubrication, water distillation, separation process, lighting, air conditioning, and refrigeration.
A gas turbine, also called a combustion turbine, is a type of continuous flow internal combustion engine. The main parts common to all gas turbine engines form the power-producing part and are, in the direction of flow:
A steamship, often referred to as a steamer, is a type of steam-powered vessel, typically ocean-faring and seaworthy, that is propelled by one or more steam engines that typically move (turn) propellers or paddlewheels. The first steamships came into practical usage during the early 1800s; however, there were exceptions that came before. Steamships usually use the prefix designations of "PS" for paddle steamer or "SS" for screw steamer. As paddle steamers became less common, "SS" is assumed by many to stand for "steamship". Ships powered by internal combustion engines use a prefix such as "MV" for motor vessel, so it is not correct to use "SS" for most modern vessels.
The Florida-class battleships of the United States Navy comprised two ships: Florida and Utah. Launched in 1910 and 1909 respectively and commissioned in 1911, they were slightly larger than the preceding Delaware class design but were otherwise very similar. This was the first US battleship class in which all ships received steam turbine engines. In the previous Delaware-class, North Dakota received steam turbine propulsion as an experiment while Delaware retained triple-expansion engines.
On a ship, the engine room (ER) is the compartment where the machinery for marine propulsion is located. The engine room is generally the largest physical compartment of the machinery space. It houses the vessel's prime mover, usually some variations of a heat engine. On some ships, there may be more than one engine room, such as forward and aft, or port or starboard engine rooms, or may be simply numbered. To increase a vessel's safety and chances of surviving damage, the machinery necessary for the ship's operation may be segregated into various spaces.
Nuclear marine propulsion is propulsion of a ship or submarine with heat provided by a nuclear reactor. The power plant heats water to produce steam for a turbine used to turn the ship's propeller through a gearbox or through an electric generator and motor. Nuclear propulsion is used primarily within naval warships such as nuclear submarines and supercarriers. A small number of experimental civil nuclear ships have been built.
The Hawkins class consisted of five heavy cruisers built for the Royal Navy during the First World War, although none of them saw service during the war. The first ship to be completed, HMS Vindictive, was renamed from HMS Cavendish and converted into an aircraft carrier while under construction. All ships were named after Elizabethan sea captains. The three ships remaining as cruisers in 1939 served in the Second World War, with Effingham being an early war loss through wreck; Raleigh had been lost in a similar shipwreck on uncharted rocks in 1922. Vindictive, though no longer a cruiser, also served throughout the War. This class formed the basis for the definition of the maximum cruiser type under the Washington Naval Treaty of 1922.
The Bangor-class minesweepers were a class of warships operated by the Royal Navy (RN), Royal Canadian Navy (RCN), Imperial Japanese Navy (IJN), and Royal Indian Navy (RIN) during the Second World War.
A thermal power station is a type of power station in which heat energy is converted to electrical energy. In a steam-generating cycle heat is used to boil water in a large pressure vessel to produce high-pressure steam, which drives a steam turbine connected to an electrical generator. The low-pressure exhaust from the turbine enters a steam condenser where it is cooled to produce hot condensate which is recycled to the heating process to generate more high pressure steam. This is known as a Rankine cycle.
The Suffren class was an interwar treaty cruiser built by France for the French Navy. The design was based on the preceding Duquesne-class cruiser and traded speed for protection while retaining the same armament. The first ship, Suffren, was completed to this design. The following ships, Colbert, Foch, Dupleix, were completed to a modified design with heavier secondary armament and rearranged topside. The ships entered service from 1930 to 1933, with Suffren being the sole survivor of the Second World War.
The Normandie class consisted of five dreadnought battleships ordered for the French Navy in 1912–1913. It comprised Normandie, the lead ship, Flandre, Gascogne, Languedoc, and Béarn. The design incorporated a radical arrangement for the twelve 340 mm (13.4 in) main battery guns: three quadruple-gun turrets, the first of their kind, as opposed to the twin-gun turrets used by most other navies. The first four ships were also equipped with an unusual hybrid propulsion system that used both steam turbines and triple-expansion steam engines to increase fuel efficiency.
An engineering officer or simply engineer, is a licensed mariner qualified and responsible for operating and maintaining the propulsion plants and support systems for a watercraft and its crew, passengers and cargo. Engineering officers are usually educated and qualified as engineering technicians.
HMS Spiteful was a Spiteful-class torpedo boat destroyer built at Jarrow, England, by Palmers Shipbuilding and Iron Company for the Royal Navy and launched in 1899. Specified to be able to steam at 30 knots, she spent her entire career serving in the seas around the British Isles.
Marine propulsion is the mechanism or system used to generate thrust to move a watercraft through water. While paddles and sails are still used on some smaller boats, most modern ships are propelled by mechanical systems consisting of an electric motor or internal combustion engine driving a propeller, or less frequently, in pump-jets, an impeller. Marine engineering is the discipline concerned with the engineering design process of marine propulsion systems.
The Umikaze-class destroyers were a class of two destroyers of the Imperial Japanese Navy. They were the first large destroyers designed for open ocean service to be built in Japan.
TS King Edward was an excursion steamer built at Dumbarton for service down the River Clyde to the Firth of Clyde and associated sea lochs on the west coast of Scotland, as far as Campbeltown. The first commercial vessel to be driven by steam turbines, King Edward was remarkably successful for a prototype, serving as a Clyde steamer for half a century from 1901 until 1951, interrupted only by service in the two world wars. The success of the vessel quickly led to the adoption of turbine propulsion for all manner of merchant vessels, from channel ferries and coastal steamers to transatlantic liners.
TSS (RMS) Mona's Queen (III) No. 145308, was a ship built for the Isle of Man Steam Packet Company in 1934. The steamer, which was the third vessel in the company's history to bear the name, was one of five ships to be specially commissioned by the company between 1927 and 1937. They were replacements for the various second-hand steamers that had been purchased to replace the company's losses during the First World War. However, the life of the Mona's Queen proved to be short: six years after being launched she was sunk by a sea mine during the Dunkirk evacuation on 29 May 1940.
Steam-powered vessels include steamboats and steamships. Smaller steamboats were developed first. They were replaced by larger steamships which were often ocean-going. Steamships required a change in propulsion technology from sail to paddlewheel to screw to steam turbines. The latter innovation changed the design of vessels to one that could move faster through the water. Engine propulsion changed to steam turbine in the early 20th century. In the latter part of the 20th century, these, in turn, were replaced by gas turbines.
The Guadiana class was a class of four destroyers employed by the Portuguese Navy between 1913 and 1942. This class is often alternatively referred as the Douro class.
The Goito class was a group of four torpedo cruisers built for the Italian Regia Marina in the 1880s. The members of the class were Goito, Montebello, Monzambano, and Confienza. They were among the first torpedo cruisers built for the Italian fleet, and were built to improve on the previous vessel, Tripoli. Experimental ships, the four Goito-class vessels varied in their dimensions, machinery, and armament, though all were comparable in terms of capabilities, having a top speed of 17 to 18 knots and carrying an armament of four or five 14-inch (360 mm) torpedo tubes.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
