Foil bearing

Last updated
A foil-air bearing for the core rotor shaft of an aircraft turbine engine. Foilbearing.jpg
A foil-air bearing for the core rotor shaft of an aircraft turbine engine.

A foil bearing, also known as a foil-air bearing, is a type of air bearing. A shaft is supported by a compliant, spring-loaded foil journal lining. Once the shaft is spinning fast enough, the working fluid (usually air) pushes the foil away from the shaft so that no contact occurs. The shaft and foil are separated by the air's high pressure, which is generated by the rotation that pulls gas into the bearing via viscosity effects. The high speed of the shaft with respect to the foil is required to initiate the air gap, and once this has been achieved, no wear occurs. Unlike aerostatic or hydrostatic bearings, foil bearings require no external pressurisation system for the working fluid, so the hydrodynamic bearing is self-starting.

Contents

Development

Foil Bearing FoilBearing.png
Foil Bearing
Load capacity against rotation speed, for Gen I and Gen III bearings Foil Bearing Capacity.png
Load capacity against rotation speed, for Gen I and Gen III bearings

Foil bearings were first developed in the late 1950s by AiResearch Mfg. Co. of the Garrett Corporation using independent R&D funds to serve military and space applications. [1] [2] They were first tested for commercial use in United Airlines Boeing 727 and Boeing 737 cooling turbines in the early and mid-1960s. [3] Garrett AiResearch air cycle machine foil bearings were first installed as original equipment in 1969 in the DC-10's environmental control systems. Garrett AiResearch foil bearings were installed on all US military aircraft to replace existing oil-lubricated rolling-contact bearings. The ability to operate at cryogenic gas temperatures and at very high temperatures gave foil bearings many other potential applications. [4]

Current-generation foil bearings with advanced coatings have greatly exceeded the limitations of earlier designs. Antiwear coatings exist that allow over 100,000 start/stop cycles for typical applications. [5]

Applications

Turbomachinery is the most common application because foil bearings operate at high speed. [6] Commercial applications in production include microturbines, [7] fuel cell blowers, [8] and air cycle machines. The main advantage of foil bearings is the elimination of the oil systems required by traditional bearing designs. Other advantages are:

Areas of current research are:

The main disadvantages are:

See also

Related Research Articles

A lubricant is a substance that helps to reduce friction between surfaces in mutual contact, which ultimately reduces the heat generated when the surfaces move. It may also have the function of transmitting forces, transporting foreign particles, or heating or cooling the surfaces. The property of reducing friction is known as lubricity.

<span class="mw-page-title-main">Gas turbine</span> Type of internal and continuous combustion engine

A gas turbine, also called a combustion turbine, is a type of continuous flow internal combustion engine. The main parts common to all gas turbine engines form the power-producing part and are, in the direction of flow:

<span class="mw-page-title-main">Ball bearing</span> Type of rolling-element bearing

A ball bearing is a type of rolling-element bearing that uses balls to maintain the separation between the bearing races.

Fluid bearings are bearings in which the load is supported by a thin layer of rapidly moving pressurized liquid or gas between the bearing surfaces. Since there is no contact between the moving parts, there is no sliding friction, allowing fluid bearings to have lower friction, wear and vibration than many other types of bearings. Thus, it is possible for some fluid bearings to have near-zero wear if operated correctly.

<span class="mw-page-title-main">Bearing (mechanical)</span> Mechanism to constrain relative movement to the desired motion and reduce friction

A bearing is a machine element that constrains relative motion to only the desired motion and reduces friction between moving parts. The design of the bearing may, for example, provide for free linear movement of the moving part or for free rotation around a fixed axis; or, it may prevent a motion by controlling the vectors of normal forces that bear on the moving parts. Most bearings facilitate the desired motion by minimizing friction. Bearings are classified broadly according to the type of operation, the motions allowed, or the directions of the loads (forces) applied to the parts.

<span class="mw-page-title-main">Labyrinth seal</span> Mechanical seal consisting of tightly interlinked parts to prevent leakage

A labyrinth seal is a type of mechanical seal that provides a tortuous path to help prevent leakage. An example of such a seal is sometimes found within an axle's bearing to help prevent the leakage of the oil lubricating the bearing.

<span class="mw-page-title-main">Lubrication</span> The presence of a material to reduce friction between two surfaces.

Lubrication is the process or technique of using a lubricant to reduce friction and wear and tear in a contact between two surfaces. The study of lubrication is a discipline in the field of tribology.

<span class="mw-page-title-main">Centrifugal compressor</span> Sub-class of dynamic axisymmetric work-absorbing turbomachinery

Centrifugal compressors, sometimes called impeller compressors or radial compressors, are a sub-class of dynamic axisymmetric work-absorbing turbomachinery.

<span class="mw-page-title-main">Magnetic bearing</span> Bearing which supports loads using magnetic levitation

A magnetic bearing is a type of bearing that supports a load using magnetic levitation. Magnetic bearings support moving parts without physical contact. For instance, they are able to levitate a rotating shaft and permit relative motion with very low friction and no mechanical wear. Magnetic bearings support the highest speeds of any kind of bearing and have no maximum relative speed.

<span class="mw-page-title-main">Plain bearing</span> Simplest type of bearing, comprising just a bearing surface and no rolling elements

A plain bearing, or more commonly sliding contact bearing and slide bearing, is the simplest type of bearing, comprising just a bearing surface and no rolling elements. Therefore, the journal slides over the bearing surface. The simplest example of a plain bearing is a shaft rotating in a hole. A simple linear bearing can be a pair of flat surfaces designed to allow motion; e.g., a drawer and the slides it rests on or the ways on the bed of a lathe.

A microturbine (MT) is a small Gas Turbine with similar cycles and components to a heavy gas turbine. The MT power-to-weight ratio is better than a heavy gas turbine because the reduction of turbine diameters causes an increase in shaft rotational speed. Heavy gas turbine generators are too large and too expensive for distributed power applications, so MTs are developed for small-scale power like electrical power generation alone or as combined cooling, heating, and power (CCHP) systems. The MT are 25 to 500 kilowatt gas turbines evolved from piston engine turbochargers, aircraft auxiliary power units (APU) or small jet engines, the size of a refrigerator. Early turbines of 30-70 kW grew to 200-250 kW.

<span class="mw-page-title-main">Turbomachinery</span> Machine for exchanging energy with a fluid

Turbomachinery, in mechanical engineering, describes machines that transfer energy between a rotor and a fluid, including both turbines and compressors. While a turbine transfers energy from a fluid to a rotor, a compressor transfers energy from a rotor to a fluid.

<span class="mw-page-title-main">Allison T56</span> American-built military turboprop (1954–)

The Allison T56 is an American single-shaft, modular design military turboprop with a 14-stage axial flow compressor driven by a four-stage turbine. It was originally developed by the Allison Engine Company for the Lockheed C-130 Hercules transport entering production in 1954. It has been a Rolls-Royce product since 1995 when Allison was acquired by Rolls-Royce. The commercial version is designated 501-D. Over 18,000 engines have been produced since 1954, logging over 200 million flying hours.

<span class="mw-page-title-main">Mohawk Innovative Technology</span>

Mohawk Innovative Technology, Inc. is an American product and research and development technology company that develops oil-free foil bearings, magnetic bearings and non-contacting foil seals for high-speed rotating machinery, such as gas turbine engines, turbochargers, compressors, cryogenic pumps, variable high-speed motors/generators and machines.

Ferrofluidicseals, or magnetic liquid rotary seals, are used in rotating equipment to enable rotary motion while maintaining a hermetic seal by means of a physical barrier in the form of a ferrofluid. The ferrofluid is suspended in place by use of a permanent magnet. Since their development in the 1970s, the seals have seen use in specialised applications such as computer disc drives, vacuum and nuclear systems.

<span class="mw-page-title-main">Centrifugal fan</span> Mechanical fan that forces fluid to move radially outward

A centrifugal fan is a mechanical device for moving air or other gases in a direction at an angle to the incoming fluid. Centrifugal fans often contain a ducted housing to direct outgoing air in a specific direction or across a heat sink; such a fan is also called a blower, blower fan, or squirrel-cage fan. Tiny ones used in computers are sometimes called biscuit blowers. These fans move air from the rotating inlet of the fan to an outlet. They are typically used in ducted applications to either draw air through ductwork/heat exchanger, or push air through similar impellers. Compared to standard axial fans, they can provide similar air movement from a smaller fan package, and overcome higher resistance in air streams.

<span class="mw-page-title-main">Albert Kingsbury</span> Engineer and inventor

Albert Kingsbury was an American engineer, inventor and entrepreneur. He was responsible for over fifty patents obtained between the years 1902 to 1930. Kingsbury is most famous for his hydrodynamic thrust bearing which uses a thin film of oil to support weights of up to 220 tons. This bearing extended the service life of many types of machinery during the early 20th century. It was primarily outfitted on Navy ships during World War I and World War II.

The exoskeletal engine (ESE) is a concept in turbomachinery design. Current gas turbine engines have central rotating shafts and fan-discs and are constructed mostly from heavy metals. They require lubricated bearings and need extensive cooling for hot components. They are also subject to severe imbalance that could wipe out the whole rotor stage, are prone to high- and low-cycle fatigue, and subject to catastrophic failure due to disc bursts from high tensile loads, consequently requiring heavy containment devices. To address these limitations, the ESE concept turns the conventional configuration inside-out and utilizes a drum-type rotor design for the turbomachinery in which the rotor blades are attached to the inside of a rotating drum instead of radially outwards from a shaft and discs. Multiple drum rotors could be used in a multi-spool design.

<span class="mw-page-title-main">Spiral groove bearing</span> Hydrodynamic bearings using spiral grooves to develop lubricant pressure

Spiral groove bearings are self-acting, or hydrodynamic bearings used to reduce friction and wear without the use of pressurized lubricants. They have this ability due to special patterns of grooves. Spiral groove bearings are self-acting because their own rotation builds up the pressure needed to separate the bearing surfaces. For this reason, they are also contactless bearings.

<span class="mw-page-title-main">Rotary union</span>

A rotary union is a union that allows for rotation of the united parts. It is thus a device that provides a seal between a stationary supply passage and a rotating part to permit the flow of a fluid into and/or out of the rotating part. Fluids typically used with rotary joints and rotating unions include various heat transfer media and fluid power media such as steam, water, thermal oil, hydraulic fluid, and coolants. A rotary union is sometimes referred to as a rotating union, rotary valve, swivel union,rotorseal, rotary couplings, rotary joint, rotating joints, hydraulic coupling, pneumatic rotary union, through bore rotary union, air rotary union, electrical rotary union, or vacuum rotary union

References

  1. Giri L. Agrawal (1997). "Foil Air/Gas Bearing Technology — An Overview" (PDF). Publication 97-GT-347. American Society of Mechanical Engineers.
  2. Giri L. Agrawal (July 1998). "Foil Bearings Cleared to Land" (PDF). Mechanical Engineering. Vol. 120, no. 7. Archived from the original (PDF) on 15 April 2016 via R&D Dynamics.
  3. Scholer Bangs (February 1973). "Foil Bearings Help Air Passengers Keep their Cool". Power Transmission Design.
  4. M. A. Barnett; A. Silver (September 1970). "Application of Air Bearings to High-Speed Turbomachinery". Technical Paper No. 700720. SAE Technical Paper Series. Society of Automotive Engineers. 1. doi:10.4271/700720. 700720.
  5. Heshmat, Hooshang (September 2005). "Major Breakthrough in Load Capacity, Speed and Operating Temperature of Foil Thrust Bearings". Technical Paper No. WT2005-63712. American Society of Mechanical Engineers. WT2005-63712. Archived from the original on 2008-02-14. Retrieved 2006-09-25.
  6. R. M. "Fred" Klaass; Christopher DellaCorte (2006). "The Quest for Oil-Free Gas Turbine Engines". SAE Technical Papers. SAE. 2006-01-3055. Archived from the original on 2007-09-30. Retrieved 2007-08-18.
  7. Lubell, D.; DellaCorte, C.; Stanford, M. (2006). "Test Evolution and Oil-Free Engine Experience of a High Temperature Foil Air Bearing Coating". Proceedings of the ASME Turbo Expo 2006: Power for Land, Sea, and Air. Vol. 5: Marine, Microturbines and Small Turbomachinery, Oil and Gas Applications, Structures and Dynamics, Parts A and B. ASME. pp. 1245–1249. doi:10.1115/GT2006-90572. ISBN   0-7918-4240-1. GT2006-90572.
  8. "Compressors with foil bearings applied in fuel cells". 13 April 2020.
  9. Some early history is reported in Giri L. Agrawal (1997), "http://www.rddynamics.com/pdfs/foil-97-gt-347.pdf — An Overview" (PDF). Publication 97-GT-347. American Society of Mechanical Engineers.