The Y-block engine is a family of overhead valveV8automobile engines produced by Ford Motor Company. The engine is well known and named for its deep skirting, which causes the engine block to resemble a Y. It was introduced in 1954 as a more modern replacement for the outdated side-valvedFord Flathead V8 and was used in a variety of Ford vehicles through 1964.
By 1948, the famous Ford Flathead V8 had been developed about as far as it could go,[1][bettersourceneeded]and it was antiquated by the early 1950s.[2] Ford was the most conservative of the major automakers, holding onto older designs longer than GM or Chrysler, but market forces pushed Ford to develop new designs in the 1950s.[2] Management at Ford instructed its engineers to develop a new engine for the future. By 1952 Ford had new, 215cuin (3.5L) OHV 6-cylinder engine and Lincoln had a 317cuin (5.2L) OHV V8.[1] The company had designed the Y-block for a 1953 introduction, but a shortage of nickel due to the Korean War's needs prevented the company from manufacturing the engine in sufficient quantities,[2] delaying it until 1954.[1]
In 1954 the Y-block displaced 239cuin (3,910cc), the same as the old Ford Flathead V8 but with a bigger bore and a shorter stroke. It produced 130bhp (97kW) as opposed to the Flathead's final 110bhp (82kW), an increase of 18%.[1] The Mercury Y-Block was 256cuin (4,194cc) and produced 161bhp (120kW),[3] again a similar displacement to the 255cuin (4.2L) Mercury Flathead V8 it replaced, but with 29% more power than the older engine's 125bhp (93kW).[4]
The original Lincoln V8 was also known as a Y-Block. Lincoln introduced their engine in 1952, but it was a different design from the Ford Y-Block, and was used on large cars and Ford heavy-duty trucks.
One of the design qualities of the Y-Block V8 is its deep skirting which makes for a very rigid block for added strength in the bottom end. The drawback to this is it also makes for a heavy cylinder block. This being Ford's first OHV engine, they had to feed oil to the rocker arm shafts through a passage from the center cam bearing. Because of the low detergents in oils of that era these passages would often become clogged giving the Y-Block a reputation for bad oiling to the top end. Ford came up with a stop gap measure for this problem by feeding oil via an external tube directly to the rocker shafts from the main oil gallery.[1]
Cylinder heads on the Y-Block have always been a point for discussion. Because of the configuration of the intake ports, vertically in pairs instead of horizontally side by side, and the way in which they make sharp turns around the head bolts, they have been called “bad breathers”. Although their flow can indeed be inferior, they are nonetheless able to rev to 7,000+rpm.[1]
Ford Y-blocks are easily identified. The distributor is located at the back of the engine and off to one side and the valve covers are held on with two studs/washers/nuts through the domed tops.
239
The first Y-block on Ford automobiles and F100 trucks was the 239cuin (3,910cc) version as released in 1954 with EBU casting numbers. The Y-block was the same displacement as the old Ford Flathead V8 that it replaced but with a bigger bore and a shorter stroke (3.5 x 3.1 in). It produced 130bhp (97kW) at 4,200rpm[5] as opposed to the flathead's final 110bhp (82kW) at 3,800rpm,[6] an increase of 18%.[1] Torque was also up compared to the Flathead, with 214lb⋅ft (290N⋅m) at 1,800rpm[5] compared with 196lb⋅ft (266N⋅m) at 2,000rpm.[6] The Y-block was considered a major advancement over the flathead. The 239 was available in 1954 models (EBU casting numbers), and in late 1954 and 1955 (EBV casting numbers), while also in 1955 the bigger 272 and 292 cubic inch siblings were introduced. The 1955 EBV 239 engine exchanges many parts with later model Y-blocks such as the 272 and 292, while the 1954 EBU engine has many parts that do not exchange with the 1955 EBV 239 and later Y-blocks.
256
The original Mercury Y-block, introduced for the 1954 model year, displaced 256cuin (4,194cc). Advertised as the "V-161" engine, it ran a bore and stroke of 3.625 x 3.1 in. The compression ratio was 7.5:1, and the rated power was 161hp (120kW) at 4,400rpm. Torque was 238lb⋅ft (323N⋅m) at 2,200rpm.[3] The engine breathed through a Holley model 2140 (4V) carburetor. The 256 version of the Mercury Y-block was only available in 1954 models and was replaced by the 292 in 1955.[3] The 256 was also used in some F100s in 1955 depending on the production plant location and was also installed in law enforcement sedans.[7]
272
By 1955 Chevrolet introduced its small block V8 with 265cuin (4.3L), not to be outdone Ford increased its displacement to 272cuin (4.5L) and introduced the Thunderbird with a 292cuin (4.8L) engine.[1] The 272cuin (4,465cc) version of the Y-Block was the same bore as the outgoing Mercury 256 cubic inch Y-Block but with a longer stroke (3.625 x 3.3 in).[8] The standard 1955 U-code featured a two barrel Holley carburetor and was rated at 162bhp (121kW) at 4,400rpm and 258lb⋅ft (350N⋅m) at 2,400rpm. The optional "Power Pack" M-code utilized a four barrel Holley carburetor and was rated at 182bhp (136kW) at 4,400rpm.[9]
In 1956 the U-code was updated to produce 173bhp (129kW) at 4,400rpm and 260lb⋅ft (353N⋅m) at 2,400rpm with a manual transmission behind it or 176bhp (131kW) at 4,400rpm and 264lb⋅ft (358N⋅m) at 2,400rpm with an automatic transmission.[10] The M-code 272 was dropped altogether in 1956 in favour of a four barrel M-code version of the 292.[1]
A final version of the 272 in the US was released in 1957 as the B-code.[11] It featured a two barrel Holley carburetor and was rated at 190bhp (142kW) at 4,500rpm and 270lb⋅ft (366N⋅m) at 2,700rpm.[12]
Ford Australia released this V8 motor as its only option in the four-door Customline sedan from 1955-1959 (based on the Canadian Meteor), and its coupé utility, based on the same styling as the Customline, called a Mainline. It was introduced in passenger cars in July 1955, and in the redesigned truck lineup one month later.[13] In late 1956 the Australian 272 switched to a four bolt 2 barrel Autolite carburetor.[14]
This engine, as well as the 292 version starting in 1956, was also produced by Ford of Brazil at its São Paulo plant facility (Ipiranga plant). A new building was opened on November 21, 1958, by the Brazilian President, Juscelino Kubitschek de Oliveira, to produce the first Ford engine in South America. The 272 version was used on Brazilian F-series trucks until 1977 and on the Brazilian Galaxie 500, launched in April 1967.
292
A 292 Y-block engine in a 1955 Ford Crown Victoria Skyliner
The 292cuin (4,778cc) Y-Block was also introduced in 1955. The 292 shared the 3.3 in (83.82mm) stroke of the 272 but with a larger 3.75 in (95.25mm) bore.[8] It was used in the Ford Thunderbird, 1959-60 Edsel, Mercury, and some high-end Ford cars. The Ford version was the P-code "Thunderbird V8", which for cars equipped with a manual transmission had a compression ratio of 8.1:1 and was rated at 193bhp (144kW) at 4,400rpm and with 280lb⋅ft (380N⋅m) at 2,600rpm. Cars equipped with an automatic transmission had a slightly higher compression ratio of 8.5:1 with a quoted 198bhp (148kW) at 4,400rpm and 286lb⋅ft (388N⋅m) at 2,500rpm.[15]
The Mercury division had two versions of the 292 available in 1955. The standard engine had a 7.6:1 compression ratio and was rated at 188bhp (140kW) at 4,400rpm, with 272lb⋅ft (369N⋅m) of torque at 2,500rpm. The top of the range Montclair V8 came with a higher specification version that was rated 198bhp (148kW) at 4,400rpm and 282lb⋅ft (382N⋅m) at 2,500rpm. 1955 would be the only model year that Mercury would use the 292 in version of the Y-Block, with it being replaced by the larger 312 in engine for the 1956 model year.[3]
In 1956 Ford replaced the P-code 292 with a new 312cuin (5.1L) "Thunderbird Special V8" version of the Y-Block, while the M-code 272 was replaced with a new M-Code specification of the 292. This M-code "Thunderbird V8" 292 was now optional on all Fords.[2] The engine when fitted behind manual transmission vehicles had an 8.0:1 compression ratio and was rated at 200bhp (149kW) at 4,600rpm and 285lb⋅ft (386N⋅m) at 2,600rpm,[16] whilst the automatic featured an 8.4:1 compression ratio with a rating of 202bhp (151kW) at 4,600rpm and 289lb⋅ft (392N⋅m) at 2,600rpm.[17]
All Ford Y-Blocks were up on power for the 1957 model year. The 292 was available as the C-code engine option, once again with a slight difference between the manual transmission and "Fordomatic" automatic transmission. Compression was up to 9.1:1 in manual cars, which were rated 206bhp (154kW) at 4,500rpm and 297lb⋅ft (403N⋅m) at 2,700rpm. Automatic vehicles were rated 212bhp (158kW) at 4,500rpm, torque and compression ratio are not listed in the Ford 1957 workshop manual as being any different from the manual car, which seems unlikely given the power difference at the same engine speed.[18]
The 292 would be the longest-lived of the Y-Blocks, carrying on until 1962 in U.S. cars and until 1964 in U.S. trucks.[1] It was also used in Argentina in the F-100 pick-up well into the 1960s, and was known as Fase I (Phase I). In 1971, the engine was modified to accept a new-style cylinder head with a different valve arrangement (E-I-E-I-E-I-E-I versus E-I-I-E-E-I-I-E), new intake and exhaust manifolds and was renamed Fase II (Phase II). In this form, the 292 Fase II continued into the 1980s in the F-100, and was also used in the Argentine Ford Fairlane (built from 1969–1982, and based heavily on the U.S. 1968 model). All Argentine versions of this engine feature a cast crankshaft rather than the forged example that equipped US heavy-duty engines. The 292 version was also produced by Ford of Brazil and equipped the Brazilian LTD starting in 1969. Both the 272 and 292 engines were replaced on Brazilian cars by the 302 windsor family engine starting on 1976 model year.
312
The 312cuin (5.1L)V8 engine came out for the 1956 model year and was again used in high-end Ford and Mercury cars, including the Thunderbird.
Bore x stroke dimensions were 3.80in ×3.44in (96.5mm ×87.4mm).
Depending on model year and application, the 312 was available with a single two- or four-barrel Holleycarburetor, two four-barrel carburetors and with or without a McCulloch (Paxton)supercharger (1957 only).[19][20]
All 1956 U.S. Mercury models were powered by the 312cuin (5.1L) V8 breathing through a four-barrel carburetor. At the beginning of the model year, a 210hp (213PS; 157kW) version with 8.0:1 compression ratio powered Mercury cars with manual transmissions (including three-speed plus overdrive), while a 225hp (228PS; 168kW) version powered cars with automatic transmissions. The 225-horsepower version had an 8.4:1 compression ratio. Later in the model year, a 235hp (238PS; 175kW) version with 9.0:1 compression ratio became available. All 1956 Mercury engines had gold-painted blocks and heads. The 210-horsepower version had red valve covers and air cleaner, while the 225-horsepower version had blue valve covers and air cleaner. The 235-horsepower version had argent silver valve covers and air cleaner. A dealer-installed "M 260" engine kit was released in January 1956. The kit consisted of a hotter camshaft, revised cylinder heads, and an intake manifold mounting two four-barrel carburetors. The kit was advertised as boosting the Mercury 312 V8 to 260hp (264PS; 194kW).
Not generally known, about 40% of these 312s were equipped with vacuum secondary CARTER WCFBs. They are a highly desired version, as the Holleys were cantankerous.[citation needed]
The 312s had no centrifugal timing advance in their distributors until 1957.
The last regular application of the 312 V8 in the U.S. was for certain 1960 Mercury models. Though considered to be a high-performance engine in 1956 and 1957, it was downgraded to an "economy" engine with low compression and two-barrel carburetor by 1960. Ford pickups used the 292cuin (4.8L) version as late as 1965.
When Ford Y-block debuted its power making ability was already hindered by its inherent displacement limit. A quick reference to the engine specifications for 1955-57 shows the Ford V8s ahead of the Chevrolet counterparts in displacement, horsepower, and torque.[citation needed] However, larger CID V8 engines made by Cadillac, Chrysler, Buick, Pontiac and Oldsmobile clearly showed the small CID architecture of the Y-block would need revision in order to keep pace with the other automakers. [citation needed]
Even with the benefit of today's technology (aftermarket rods and stroker cranks), the upper limit of a Y-block is about 348cuin (5.7L), while the Chevrolet could be modified well past the factory limit of 400cuin (6.6L). The result was the introduction in 1958 of the 332 CID "big block" Ford FE engine which ultimately grew to 428 cu in. Later, in 1962, the Ford Windsor engine– which began at 221cuin (3.6L) would fully replace the Y-Block and grow to 351cuin (5.8L).
Related Research Articles
The Ford FE engine is a medium block V8 engine produced by the Ford Motor Company and used in vehicles sold in the North American market between 1958 and 1976. The FE, derived from 'Ford-Edsel', was introduced just four years into the short-lived Ford Y-block engine, which American cars and trucks were outgrowing. It was designed with room to be significantly expanded, and manufactured both as a top-oiler and side-oiler, and in displacements between 332 cu in (5.4 L) and 428 cu in (7.0 L).
The Ford 335 engine family was a group of engines built by the Ford Motor Company between 1969 and 1982. The "335" designation reflected Ford management's decision to produce an engine of that size with room for expansion during its development. This engine family began production in late 1969 with a 351 cu in (5.8 L) engine, commonly called the 351C. It later expanded to include a 400 cu in (6.6 L) engine which used a taller version of the engine block, commonly referred to as a tall deck engine block, a 351 cu in (5.8 L) tall deck variant, called the 351M, and a 302 cu in (4.9 L) engine which was exclusive to Australia.
The Plymouth Barracuda is a two-door pony car that was manufactured by Chrysler Corporation from 1964 through 1974 model years.
The Ford small-block is a series of 90° overhead valve small-block V8 automobile engines manufactured by the Ford Motor Company from July 1961 to December 2000.
The Chrysler B and RB engines are a series of big-block V8 gasoline engines introduced in 1958 to replace the Chrysler FirePower engines. The B and RB engines are often referred to as "wedge" engines because they use wedge-shaped combustion chambers; this differentiates them from Chrysler's 426 Hemi big block engines that are typically referred to as "Hemi" or "426 Hemi" due to their hemispherical shaped combustion chambers. The corporation had been seeking a smaller and lighter replacement for its FirePower engines, in part because new styling dictates meant moving the engine forward in the chassis which negatively affected weight distribution.
The Slant-Six is the popular name for a Chrysler inline-6 internal combustion engine with an overhead valve reverse-flow cylinder head and cylinder bank inclined at a 30-degree angle from vertical. Introduced in 1959 for the 1960 models, it was known within Chrysler as the G-engine. It was a clean-sheet design that began production in 1959 at 170 cubic inches (2.8 L) and ended in 2000 at 225 cubic inches (3.7 L). It was a direct replacement for the flathead Chrysler straight six that the company started business with in 1925 until the old design was discontinued in the 1960s.
The Chevrolet "big-block" engine is a term for a series of large-displacement, naturally-aspirated, 90°, overhead valve, gasoline-powered, V8 engines; that were developed and produced by the Chevrolet Division of General Motors, from the 1950s until present.
The Chevrolet small-block engine is a series of gasoline-powered V8 automobile engines, produced by the Chevrolet division of General Motors between 1954 and 2003, using the same basic engine block. Referred to as a "small-block" for its size relative to the physically much larger Chevrolet big-block engines, the small-block family spanned from 262 cu in (4.3 L) to 400 cu in (6.6 L) in displacement. Engineer Ed Cole is credited with leading the design for this engine. The engine block and cylinder heads were cast at Saginaw Metal Casting Operations in Saginaw, Michigan.
The Pontiac V8 engine is a family of overhead valve 90° V8 engines manufactured by the Pontiac Division of General Motors Corporation between 1955 and 1981. The engines feature a cast-iron block and head and two valves per cylinder. Engine block and cylinder heads were cast at Saginaw Metal Casting Operations then assembled at Tonawanda Engine before delivery to Pontiac Assembly for installation.
The Essex V6 is a 90° V6 engine family built by the Ford Motor Company at the Essex Engine Plant in Windsor, Ontario, Canada. This engine is unrelated to Ford's British Essex V6. Introduced in 1982, versions of the Essex V6 engine family were used in subcompact through to large cars, vans, minivans, and some pickup trucks. The Essex V6 was last used in the 2008 regular-cab F-150, after which it was succeeded by a version of the Ford Cyclone engine. An industrial version of the engine was available until 2015.
The Oldsmobile V8, also referred to as the Rocket, is a series of engines that was produced by Oldsmobile from 1949 until 1990. The Rocket, along with the 1949 Cadillac V8, were the first post-war OHV crossflow cylinder head V8 engines produced by General Motors. Like all other GM divisions, Olds continued building its own V8 engine family for decades, adopting the corporate Chevrolet 350 small-block and Cadillac Northstar engine only in the 1990s. All Oldsmobile V8s were assembled at plants in Lansing, Michigan while the engine block and cylinder heads were cast at Saginaw Metal Casting Operations.
The Buick V8 is a family of V8 engines produced by the Buick division of General Motors (GM) between 1953 and 1981. All were 90° water-cooled V8 OHV pushrod engines, and all were naturally aspirated except one turbocharged version of the 215.
The Ford flathead V8 is a V8 engine with a flat cylinder head introduced by the Ford Motor Company in 1932 and built by Ford through 1953. During the engine's first decade of production, when overhead-valve engines were used by only a small minority of makes, it was usually known simply as the Ford V‑8, and the first car model in which it was installed, the Model 18, was often called simply the "Ford V-8" after its new engine. An automotive milestone as the first affordable V8, it ranks as one of the company's most important developments. The engine was intended to be used for big passenger cars and trucks; it was installed in such until 1953, making the engine's 21-year production run for the U.S. consumer market longer than the 19-year run of the Ford Model T engine. It was also built independently by Ford licensees.. The engine was named on Ward's list of the 10 best engines of the 20th century. It was a staple of hot rodders in the 1950s, and it remains famous in the classic car hobbies even today, despite the huge variety of other popular V8s that followed.
The Ford Motor Company produced straight-six engines from 1906 until 1908 and from 1941 until 2016. In 1906, the first Ford straight-six was introduced in the Model K. The next was introduced in the 1941 Ford. Ford continued producing straight-six engines for use in its North American vehicles until 1996, when they were discontinued in favor of more compact V6 designs.
The Ford MEL is a big-block 90° V8 engine family produced in various configurations by the Ford Motor Company between 1958 and 1967 in displacements from 383–462 cubic inches (6.3–7.6 L), and used in Ford, Edsel, Mercury, and Lincoln vehicles.
The Lincoln Y-block V8 engine was Ford's earliest OHV V8 engine, introduced by Lincoln in the 1952 model year. Like the later and better-known but even more short-lived Ford Y-block engine, its block's deep skirts gave the block the appearance of the letter Y from the front.
The Prince G-series engine was the company's only straight-four and straight-six engines which began production in 1955. A number of variations were made, with both OHV and OHC heads. A diesel four-cylinder with 1.9 L (1,862 cc) was also built, called the D-6. The G series was used in the Skyline, the Laurel, and the Gloria from the 1950s to the early 1970s.
The Chrysler Hemi engine, known by the trademark Hemi or HEMI, refers to a series of high-performance American overhead valve V8 engines built by Chrysler with hemispherical combustion chambers. Three generations have been produced: the FirePower series from 1951 to 1958; a famed 426 cu in (7.0 L) race and street engine from 1964-1971; and family of advanced Hemis (displacing between 5.7 L 6.4 L from 2003 to the present.
The Ford Fairlane is an automobile model that was sold between the 1955 and 1970 model years by Ford in North America. Taking its name from the Dearborn, Michigan estate of Henry Ford, the Fairlane nameplate was used for seven different generations of vehicles. Through its production, the model line would be marketed in a wide variety of body styles, including two-door and four-door sedans, two-door and four-door hardtops, station wagons, and both traditional and retractable-hardtop convertibles.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
