The Gakken EX-System is a series of educational electronics kits produced by Gakken in the late 1970s. The kits use denshi blocks (also known as electronic blocks) to allow electronics experiments to be performed easily and safely. Over 25 years after its original release, one of the main kits from the series was reissued in Japan in 2002.
A brief timeline:
An EX-System kit consists of:
A denshi block (or electronic block) is a small plastic box containing an electronic component. Each block has conductive metal strips on its sides, and when two blocks are placed side-by-side, their metal strips touch allowing electricity to flow between them. The top of each block is labelled with a schematic representation of the component it contains.
A circuit is built by placing a configuration of denshi blocks in a two dimensional grid. Because of the two dimensional layout and the labels on the blocks, a configuration of blocks resembles a schematic of the circuit.
While most denshi blocks are of a standard size, there are some larger blocks for containing complex components. In particular, the synthesiser block and the FM tuner block are much larger, occupying an area 4x5 standard blocks and 3x6 standard blocks, respectively.
The main unit holds the grid of blocks (it has room for 6×8 standard blocks), batteries and some additional circuitry. When fully expanded, the main unit contains:
Some circuits require apparatus which are unsuitable for putting inside blocks, for example, a crystal earpiece. These have wires which terminate in flat metal contacts, and they are connected to the circuit by sliding the contacts between the metal strips of two neighbouring blocks.
Some experiments also involve non-electrical apparatus, for example, the optical fibres from the optical experiments kit. The optical fibres are connected via a special block.
The instruction booklet gives the correct arrangement of blocks to make each circuit, a full schematic for it and a brief explanation of how the experiment works.
The names of the original kits, EX-15, EX-30, etc., give the number of experiments that could be performed with them. By purchasing expansion kits, EX-A, EX-B, etc., any of the kits could be upgraded to support the complete set of 191 experiments. Each expansion kit added new denshi blocks and came with a piece of external apparatus or some circuitry to be installed in the main unit.
Note that the EX-FM kit is compatible with all of the main kits, although some of its experiments require blocks from later kits in the series.
| Name | As upgrade | Significant components | Example experiment |
|---|---|---|---|
| EX-15 | antenna, crystal earpiece | Diode Detector Radio | |
| EX-30 | EX-15 + EX-A | morse key block, short cables | Morse Code Practice Circuit |
| EX-60 | EX-30 + EX-B | IC Amplifier | I-Diode Detector + IC Radio (Fixed Bias) |
| EX-100 | EX-60 + EX-C | tester probes | Wireless Water Level Warning Device |
| EX-120 | EX 100 + EX-D | microphone, CdS cell | Circuit which Buzzes when Struck by Light |
| EX-150 | EX-120 + EX-E | analogue meter | Noise Level Meter |
| EX-181 | EX-150 + EX-System Synthesiser | synthesiser block, resistance board | Sound of Car being Reversed |
| EX-FM | any main kit + EX-FM | FM tuner block | FM Receiver with Microphone Mixer |
The reissued EX-150 kit from 2002 is almost identical to the original EX-150 from the 1970s. Due to differences in the availability of certain components, there are changes in some of the circuitry. A consequence is that some of the experiments have been altered.
The reissued EX-150 sold well enough to justify an expansion kit. It is designed for the reissued EX-150 only and, allegedly, will not work with the original. The expansion contains components for performing optical experiments, including LED blocks, optical fibres and a 555 timer IC block. As some of the experiments involve two separate circuits, a plastic tray with room for 6 x 5 standard blocks is also provided.
An example experiment:
The sound synthesiser was based around the Texas Instruments SN76477 sound chip. Since the chip requires a separate 9V power supply, the synthesiser block had a compartment for holding a 9V battery.
Although the EX-FM tuner block supported 10 new experiments in Japan, in the English language version available in Europe, only 4 experiments are described.
A Japanese man, Hiroyuki Inoue, built an IPv6 communication module as a block for the EX-150. [1]
The Denshi Block system was also sold under the Humbrol, Skilcraft [2] and Tron Link [3] brands.
The FX-System was introduced in 1981. [4] It used the TMS1000 processor.
A motherboard is the main printed circuit board (PCB) in general-purpose computers and other expandable systems. It holds and allows communication between many of the crucial electronic components of a system, such as the central processing unit (CPU) and memory, and provides connectors for other peripherals. Unlike a backplane, a motherboard usually contains significant sub-systems, such as the central processor, the chipset's input/output and memory controllers, interface connectors, and other components integrated for general use.
A breadboard, solderless breadboard, or protoboard is a construction base used to build semi-permanent prototypes of electronic circuits. Unlike a perfboard or stripboard, breadboards do not require soldering or destruction of tracks and are hence reusable. For this reason, breadboards are also popular with students and in technological education.
An analog synthesizer is a synthesizer that uses analog circuits and analog signals to generate sound electronically.
A single-board computer (SBC) is a complete computer built on a single circuit board, with microprocessor(s), memory, input/output (I/O) and other features required of a functional computer. Single-board computers are commonly made as demonstration or development systems, for educational systems, or for use as embedded computer controllers. Many types of home computers or portable computers integrate all their functions onto a single printed circuit board.
A circuit diagram is a graphical representation of an electrical circuit. A pictorial circuit diagram uses simple images of components, while a schematic diagram shows the components and interconnections of the circuit using standardized symbolic representations. The presentation of the interconnections between circuit components in the schematic diagram does not necessarily correspond to the physical arrangements in the finished device.
Heathkit is the brand name of kits and other electronic products produced and marketed by the Heath Company. The products over the decades have included electronic test equipment, high fidelity home audio equipment, television receivers, amateur radio equipment, robots, electronic ignition conversion modules for early model cars with point style ignitions, and the influential Heath H-8, H-89, and H-11 hobbyist computers, which were sold in kit form for assembly by the purchaser.
Place and route is a stage in the design of printed circuit boards, integrated circuits, and field-programmable gate arrays. As implied by the name, it is composed of two steps, placement and routing. The first step, placement, involves deciding where to place all electronic components, circuitry, and logic elements in a generally limited amount of space. This is followed by routing, which decides the exact design of all the wires needed to connect the placed components. This step must implement all the desired connections while following the rules and limitations of the manufacturing process.
A denshi block is a small plastic box containing an electronic component. The blocks are used in some educational electronics kits, such as the Gakken EX-150, to allow experiments to be performed easily and safely.
The Acorn System 1, initially called the Acorn Microcomputer (Micro-Computer), was an early 8-bit microcomputer for hobbyists, based on the MOS 6502 CPU, and produced by British company Acorn Computers from 1979.
Founded by David Hafler and Ed Laurent in Philadelphia, Pennsylvania in 1955, Dynaco was an American hi-fi audio system manufacturer popular in the 1960s and 1970s for its wide range of affordable, yet high quality audio components.. Its best known product was the ST-70 tube stereo amplifier. They also manufactured other tube and solid state amplifiers, preamplifiers, radio tuners and bookshelf loudspeakers. Dynaco was liquidated in 1980, and the trademark is now owned by Radial Engineering Ltd.
An electronic kit is a package of electrical components used to build an electronic device. Generally, kits are composed of electronic components, a circuit diagram (schematic), assembly instructions, and often a printed circuit board (PCB) or another type of prototyping board.
The Fibre Channel electrical interface is one of two related Fibre Channel standards that can be used to physically interconnect computer devices. The other standard is a Fibre Channel optical interface, which is not covered in this article.
The Gibson RD series solid body electric guitars were launched in 1977. Distinguished by its active electronics, they were designed to appeal to those interested in synthesizers as well as guitars. An "unhappy marriage of traditional and modern design", the series was unsuccessful, though the concept of the RD was continued for a while in the Les Paul Artist series.
Gakken Holdings Co., Ltd. is a Japanese publishing company founded in 1947 by Hideto Furuoka, which also produces educational toys. Their annual sales are reported at ¥ 90 billion.
Lectron was a modular electronic experimentation kit designed to introduce youth to basic electronic circuits and theory.
Computer hardware includes the physical parts of a computer, such as the central processing unit (CPU), random access memory (RAM), motherboard, computer data storage, graphics card, sound card, and computer case. It includes external devices such as a monitor, mouse, keyboard, and speakers.
This glossary of computer hardware terms is a list of definitions of terms and concepts related to computer hardware, i.e. the physical and structural components of computers, architectural issues, and peripheral devices.
An optical cage system is an optomechanical system that is used to mount optical elements such as lenses and mirrors together in a rigid assembly. Optical systems built this way can be more compact than can be achieved using an optical table, and the system provides more flexibility than an optical rail. A cage system allows optical engineers and researchers to make self-contained instrument-like systems, without having to machine any custom parts. They are useful for education and research, and for making quick prototypes of new optical designs.
The littleBits Synth Kit is an analogue modular synthesiser developed by the American electronics startup littleBits in collaboration with the Japanese music technology company Korg. Released in late 2013 after a design process of around nine months, the kit features 12 small modules that can be connected to form larger circuits. Several of these bits are adapted from circuits used in Korg's Monotron synthesisers. A booklet detailing over 10 example projects to follow is sold with the kit. A later version of the Synth Kit, the Synth Pro Kit, was released in June 2015 and added three new bits that provide external connectivity for the kit.
{{cite web}}: CS1 maint: bot: original URL status unknown (link)Dostál, J. Electronic kits in education. [ permanent dead link ] Olomouc, EU: Votobia, 2008. 74 s. ISBN 978-80-7220-308-6.[ dead link ]