| Vector 1 | |
|---|---|
 | |
| Role | Glider |
| National origin | United States |
| Manufacturer | Stan Hall |
| Designer | Stan Hall |
| First flight | 1975 |
| Introduction | 1975 |
| Number built | one |
The Hall Vector 1 is an American high-wing, ultralight glider that was designed by Stan Hall for serious cross-country flights. [1]
The Vector 1 was intended to take advantage of the US informal rules for hang gliders at the time of its development that in 1982 became the FAR 103 Ultralight Vehicles regulations. These define a hang glider as any unpowered glider with an empty weight of 155 lb (70 kg) or less. The Vector 1 was designed with the goal of building a foot-launchable glider with cross country performance.
With an empty weight of 150 lb (68 kg), the design qualifies as a hang glider and thus does not need to be registered or have a Certificate of Airworthiness. The aircraft resembles a small sailplane and not a traditional hang glider. [1] [2]
The aircraft achieves its light weight through small dimensions, with a wingspan of only 34 ft (10.4 m). The Vector 1 was designed to be foot-launched, with the pilot sitting on a bicycle saddle. After becoming airborne a pair of spring-loaded and hydraulically dampened doors are then closed. The pilot then lands on a fixed skid. The aircraft as designed cannot be tow-launched. [1]
The Vector 1 is made with an all-wooden structure, covered with doped aircraft fabric covering. The wing has conventional three-axis controls and incorporates spoilers. The airfoil is a Wortmann FX-MS-150-B, which was developed for low-speed flight. [1]
The Vector 1 was conceived with four design goals. First was to double the L/D of the then state of the art in foot-launched hang gliders. Hall designed the glider for an L/D of 18:1. Second was for the glider to have full three axis control, operated conventionally. Third was for the design limit load to be 5.33 g, in accordance with the minimum sailplane standard of the time and with the intention for the Vector 1 to be soared like a sailplane. Fourth was that the Vector 1 to be simple and economical to construct. [3]
Vector 1's 150 lb (68 kg) weight came in 25 lb (11 kg) over the weight target that Hall initially hoped for. The root cause for the overweight condition was in the design criteria, especially numbers three and four. The high limit load led to more structural weight. In the interest of affordability Hall used Douglas-fir and Finnish birch plywood for the main structure instead of spruce and mahogany plywood which are lighter, but more expensive and more difficult to procure. He also used streamlined steel bracing for the wing strut because he was unable to find streamlined aluminum parts that would have been structurally sufficient. These weight gains, coupled with the large proportion of gross weight that is made up by the pilot weight and the high pitching moment of the Wortmann FX-MS-150-B airfoil led to the center of gravity of the glider being too far forward. This required Hall to place eight pounds of lead ballast in the tail and enlarge the horizontal tail surfaces. [4]
As a result of the extra weight, more wind was required for successful foot-launching of the Vector 1. As a result, Hall modified the prototype so that it could be auto towed for initial test flights. The test flights exposed the center of gravity issues and showed that with the extra weight the Vector 1 simply flew too fast for safe foot launching. Hall constructed a canopy to try to smooth airflow over the wing center section and thus reduce the stall speed to bring the Vector 1 back down to foot-launching speeds but eventually he lost interest in the project and never flew it again. [4]
Only one example was designed and built between 1973 and 1975 and six test flights were made. [4] In 1983 it was reportedly in storage and had not been flown for a number of years. [1]
On the future of the aircraft, Hall wrote in September 1980:
Is there any future for Vector I? As a foot-launcher, I doubt it. At least I don’t plan to foot launch her. Bones too brittle. As to my permitting someone else to fly her, I’m afraid my requirements for sailplane experience would find few candidates. Most of the pilots whom I would trust would likely feel as I do — too little performance to be interesting. I have my own high-performer to play with in Ibex, and I can do it without having to huff and puff my way up the side of a hill. Anyway, I have too much sweat invested in the aircraft not to be exceedingly particular. Too particular, probably. [4]
Data from Soaring [1]
General characteristics
Performance
Aircraft of comparable role, configuration, and era
The Schleicher ASW 15 is a one-seat sailplane designed in 1968 by Gerhard Waibel and manufactured by Alexander Schleicher GmbH & Co. The ASW 15 has shoulder-mounted wings and an all-flying tailplane, with its single tow-release placement a compromise between winching and aerotowing. The later ASW 15B had several improvements, including a tow-release placed on the plane of symmetry, an 11 cm taller rudder, a slightly larger main wheel, and the provision of a 90-litre water ballast system.
The Glasflügel 303 Mosquito is a composite 15 metre Class single-seat sailplane manufactured by Glasflügel between 1976 and 1980.
The Schweizer SGS 1-34 is a United States Standard Class, single-seat, high-wing glider built by Schweizer Aircraft of Elmira, New York.
The Glasflügel 604 is a high-wing, T-tailed, single seat, FAI Open Class glider that was designed and produced in West Germany by Glasflügel starting in 1970.
The Laister LP-15 Nugget is an American single-seat, high-wing glider designed by Jack and Bill Laister for the FAI Standard Class.
The Bikle T-6 is an American, mid-wing, single seat, glider designed by Paul Bikle and based upon the design of the Schreder HP-14. Even though only one T-6 was built it is noted as the most tested and studied glider with complete data published. It has been used extensively as a comparative reference glider for evaluating other designs during in-flight comparisons.
The Schreder HP-17 was an American mid-wing, V tailed, single seat, experimental glider designed by Richard Schreder to test a new airfoil section.
The Gehrlein GP-1 is an American mid-wing, single seat FAI Standard Class glider that was designed by Jay and Rod Gehrlein and first flown in July 1968.
The Luenger Beta 1 was an American high-wing, single-seat, T-tailed FAI Open Class glider designed by Hans Luenger and Spud Kohler.
The Monaghan Osprey is an American mid-wing, single-seat, T-tailed, FAI Standard Class glider that was designed and constructed by Richard C. Monaghan of Pearblossom, California.
The Parker RP9 T-Bird is an American, high-wing, T-tailed, single-seat, FAI Open Class glider that was designed and constructed by Ray Parker between 1956 and 1962.
The Whigham GW-2 is an American high-wing, single-seat, V-tailed, FAI Open Class glider that was designed and constructed by Gene Whigham, a retired flight test engineer for Convair.
The Whigham GW-5 is an American mid-wing, single seat, FAI Standard Class glider that was designed and constructed by Gene Whigham, a retired flight test engineer for Convair.
The Maupin Carbon Dragon is an American, high-wing, single-seat, glider that was designed by Jim Maupin and made available as plans for amateur construction. Plans are no longer available.
The Glasflügel 205 Club Libelle is a high wing, T-tailed, single seat glider that was designed and produced in West Germany by Glasflügel for club and rental use.
The Lehtovaara PIK-16 Vasama is a Finnish mid-wing, single-seat, FAI Standard Class glider that was designed by Tuomo Tervo, Jorma Jalkanen and Kurt Hedstrom, who were students at the Polyteknikkojen Ilmailukerho (PIK) and produced by Lehtovaara.
The Masak Scimitar was an American mid-wing, single-seat glider that was designed and constructed by Peter Masak.
The Rensselaer RP-1 is an American low-wing, single-seat, foot-launchable glider that was designed and produced by the Rensselaer Polytechnic Institute of Troy, New York.
The EEL ULF 1 is a West German high-wing, single-seat, foot-launched, microlift glider that was designed by Dieter Reich. When it was available it was provided in the form of plans by Entwicklung und Erprobung von Leichtflugzeugen (EEL) for amateur construction. By the end of 2019 the company website had been take down and it is likely that the company has gone out of business.
The Mitchell Wing B-10 is an American high-wing, open cockpit, single-seat ultralight aircraft and motor glider that was designed by Don Mitchell and produced by a variety of companies in the form of kits and plans for amateur construction.