Injection locking

Last updated

Injection locking and injection pulling are the frequency effects that can occur when a harmonic oscillator is disturbed by a second oscillator operating at a nearby frequency. When the coupling is strong enough and the frequencies near enough, the second oscillator can capture the first oscillator, causing it to have essentially identical frequency as the second oscillator. This is injection locking. When the second oscillator merely disturbs the first but does not capture it, the effect is called injection pulling. Injection locking and pulling effects are observed in numerous types of physical systems, however the terms are most often associated with electronic oscillators or laser resonators.

Contents

Injection locking has been used in beneficial and clever ways in the design of early television sets and oscilloscopes, allowing the equipment to be synchronized to external signals at a relatively low cost. Injection locking has also been used in high performance frequency doubling circuits. However, injection locking and pulling, when unintended, can degrade the performance of phase-locked loops and RF integrated circuits.

Injection from grandfather clocks to lasers

Injection pulling and injection locking can be observed in numerous physical systems where pairs of oscillators are coupled together. Perhaps the first to document these effects was Christiaan Huygens, the inventor of the pendulum clock, who was surprised to note that two pendulum clocks which normally would keep slightly different time nonetheless became perfectly synchronized when hung from a common beam. Modern researchers have confirmed his suspicion that the pendulums were coupled by tiny back-and-forth vibrations in the wooden beam. [1] The two clocks became injection locked to a common frequency.

Cross coupled LC oscillator with output on top Cross coupled LC oscillator.svg
Cross coupled LC oscillator with output on top

In a modern-day voltage-controlled oscillator an injection-locking signal may override its low-frequency control voltage, resulting in loss of control. When intentionally employed, injection locking provides a means to significantly reduce power consumption and possibly reduce phase noise in comparison to other frequency synthesizer and PLL design techniques. In similar fashion, the frequency output of large lasers can be purified by injection locking them with high accuracy reference lasers (see injection seeder).

Injection-locked oscillator

An injection-locked oscillator (ILO) is usually based on cross-coupled LC oscillator. It has been employed for frequency division [2] or jitter reduction in PLL, with the input of pure sinusoidal waveform. It was employed in continuous mode clock and data recovery (CDR) or clock recovery to perform clock restoration from the aid of either preceding pulse generation circuit to convert non-return-to-zero (NRZ) data to pseudo-return-to-zero (PRZ) format [3] or nonideal retiming circuit residing at the transmitter side to couple the clock signal into the data. [4] In the late 2000s, the ILO was employed for a burst-mode clock-recovery scheme. [5]

The ability to injection-lock is an inherent property of all oscillators (electronic or otherwise). This capability can be fundamentally understood as the combined effect of the oscillator's periodicity with its autonomy. Specifically, consider a periodic injection (i.e., external disturbance) that advances or lags the oscillator's phase by some phase shift every oscillation cycle. Due to the oscillator's periodicity, this phase shift will be the same from cycle to cycle if the oscillator is injection-locked. Moreover, due to the oscillator's autonomy, each phase shift persists indefinitely. Combining these two effects produces a fixed phase shift per oscillation cycle, which results in a constant frequency shift over time. If the resultant, shifted oscillation frequency matches the injection frequency, the oscillator is said to be injection-locked. However, if the maximum frequency shift that the oscillator can experience due to the injection is not enough to cause the oscillation and injection frequencies to coincide (i.e., the injection frequency lies outside the lock range), the oscillator can only be injection pulled (see Injection pulling). [6]

Unwanted injection locking

High-speed logic signals and their harmonics are potential threats to an oscillator. The leakage of these and other high frequency signals into an oscillator through a substrate concomitant with an unintended lock is unwanted injection locking.

Gain by injection locking

Injection locking can also provide a means of gain at a low power cost in certain applications.

Injection pulling

Gnome-mime-sound-openclipart.svg
"Injection Locking and Pulling"
Injection pulling and locking heard alternatively when one oscillator of two sweeps in frequency
Problems playing this file? See media help.

Injection (aka frequency) pulling occurs when an interfering frequency source disturbs an oscillator but is unable to injection lock it. The frequency of the oscillator is pulled towards the frequency source as can be seen in the spectrogram. The failure to lock may be due to insufficient coupling, or because the injection source frequency lies outside the locking window (also known as the lock range) of the oscillator. Injection pulling fundamentally corrupts the inherent periodicity of an oscillator.

Spectrogram of the above audio InjectionLockedOscillatorsSpectrogram.png
Spectrogram of the above audio

Entrainment

Entrainment has been used to refer to the process of mode locking of coupled driven oscillators, which is the process whereby two interacting oscillating systems, which have different periods when they function independently, assume a common period. The two oscillators may fall into synchrony, but other phase relationships are also possible. The system with the greater frequency slows down, and the other speeds up.

Dutch physicist Christiaan Huygens, the inventor of the pendulum clock, introduced the concept after he noticed, in 1666, that the pendulums of two clocks mounted on a common board had synchronized, and subsequent experiments duplicated this phenomenon. He described this effect as "odd sympathy". The two pendulum clocks synchronized with their pendulums swinging in opposite directions, 180° out of phase, but in-phase states can also result. Entrainment occurs because small amounts of energy are transferred between the two systems when they are out of phase in such a way as to produce negative feedback. As they assume a more stable phase relationship, the amount of energy gradually reduces to zero. In the realm of physics, Huygens' observations are related to resonance and the resonant coupling of harmonic oscillators, which also gives rise to sympathetic vibrations.

A 2002 study of Huygens' observations show that an antiphase stable oscillation was somewhat fortuitous, and that there are other possible stable solutions, including a "death state" where a clock stops running, depending on the strength of the coupling between the clocks. [7]

Mode locking between driven oscillators can be easily demonstrated using mechanical metronomes on a common, easily movable surface. [8] [9] [10] Such mode locking is important for many biological systems including the proper operation of pacemakers. [11]

The use of the word entrainment in the modern physics literature most often refers to the movement of one fluid, or collection of particulates, by another (see Entrainment (hydrodynamics)). The use of the word to refer to mode locking of non-linear coupled oscillators appears mostly after about 1980, and remains relatively rare in comparison.

A similar coupling phenomenon was characterized in hearing aids when the adaptive feedback cancellation is used. This chaotic artifact (entrainment) is observed when correlated input signals are presented to an adaptive feedback canceller.

In recent years, aperiodic entrainment has been identified as an alternative form of entrainment that is of interest in biological rhythms. [12] [13] [14]

See also

Related Research Articles

<span class="mw-page-title-main">Oscillation</span> Repetitive variation of some measure about a central value

Oscillation is the repetitive or periodic variation, typically in time, of some measure about a central value or between two or more different states. Familiar examples of oscillation include a swinging pendulum and alternating current. Oscillations can be used in physics to approximate complex interactions, such as those between atoms.

<span class="mw-page-title-main">Synchronization</span> Coordination of events to operate a system in unison

Synchronization is the coordination of events to operate a system in unison. For example, the conductor of an orchestra keeps the orchestra synchronized or in time. Systems that operate with all parts in synchrony are said to be synchronous or in sync—and those that are not are asynchronous.

<span class="mw-page-title-main">Crystal oscillator</span> Electronic oscillator circuit

A crystal oscillator is an electronic oscillator circuit that uses a piezoelectric crystal as a frequency-selective element. The oscillator frequency is often used to keep track of time, as in quartz wristwatches, to provide a stable clock signal for digital integrated circuits, and to stabilize frequencies for radio transmitters and receivers. The most common type of piezoelectric resonator used is a quartz crystal, so oscillator circuits incorporating them became known as crystal oscillators. However, other piezoelectricity materials including polycrystalline ceramics are used in similar circuits.

A phase-locked loop or phase lock loop (PLL) is a control system that generates an output signal whose phase is fixed relative to the phase of an input signal. Keeping the input and output phase in lockstep also implies keeping the input and output frequencies the same, thus a phase-locked loop can also track an input frequency. And by incorporating a frequency divider, a PLL can generate a stable frequency that is a multiple of the input frequency.

<span class="mw-page-title-main">Phase noise</span> Frequency domain representation of random fluctuations in the phase of a waveform

In signal processing, phase noise is the frequency-domain representation of random fluctuations in the phase of a waveform, corresponding to time-domain deviations from perfect periodicity (jitter). Generally speaking, radio-frequency engineers speak of the phase noise of an oscillator, whereas digital-system engineers work with the jitter of a clock.

<span class="mw-page-title-main">Pendulum</span> Mechanism for regulating the speed of clocks

A pendulum is a device made of a weight suspended from a pivot so that it can swing freely. When a pendulum is displaced sideways from its resting, equilibrium position, it is subject to a restoring force due to gravity that will accelerate it back toward the equilibrium position. When released, the restoring force acting on the pendulum's mass causes it to oscillate about the equilibrium position, swinging back and forth. The time for one complete cycle, a left swing and a right swing, is called the period. The period depends on the length of the pendulum and also to a slight degree on the amplitude, the width of the pendulum's swing.

<span class="mw-page-title-main">Resonator</span> Device or system that exhibits resonance

A resonator is a device or system that exhibits resonance or resonant behavior. That is, it naturally oscillates with greater amplitude at some frequencies, called resonant frequencies, than at other frequencies. The oscillations in a resonator can be either electromagnetic or mechanical. Resonators are used to either generate waves of specific frequencies or to select specific frequencies from a signal. Musical instruments use acoustic resonators that produce sound waves of specific tones. Another example is quartz crystals used in electronic devices such as radio transmitters and quartz watches to produce oscillations of very precise frequency.

In electronic instrumentation and signal processing, a time-to-digital converter (TDC) is a device for recognizing events and providing a digital representation of the time they occurred. For example, a TDC might output the time of arrival for each incoming pulse. Some applications wish to measure the time interval between two events rather than some notion of an absolute time.

A Colpitts oscillator, invented in 1918 by Canadian-American engineer Edwin H. Colpitts using vacuum tubes, is one of a number of designs for LC oscillators, electronic oscillators that use a combination of inductors (L) and capacitors (C) to produce an oscillation at a certain frequency. The distinguishing feature of the Colpitts oscillator is that the feedback for the active device is taken from a voltage divider made of two capacitors in series across the inductor.

Brainwave entrainment, also referred to as brainwave synchronization or neural entrainment, refers to the observation that brainwaves will naturally synchronize to the rhythm of periodic external stimuli, such as flickering lights, speech, music, or tactile stimuli.

<span class="mw-page-title-main">Neural oscillation</span> Brainwaves, repetitive patterns of neural activity in the central nervous system

Neural oscillations, or brainwaves, are rhythmic or repetitive patterns of neural activity in the central nervous system. Neural tissue can generate oscillatory activity in many ways, driven either by mechanisms within individual neurons or by interactions between neurons. In individual neurons, oscillations can appear either as oscillations in membrane potential or as rhythmic patterns of action potentials, which then produce oscillatory activation of post-synaptic neurons. At the level of neural ensembles, synchronized activity of large numbers of neurons can give rise to macroscopic oscillations, which can be observed in an electroencephalogram. Oscillatory activity in groups of neurons generally arises from feedback connections between the neurons that result in the synchronization of their firing patterns. The interaction between neurons can give rise to oscillations at a different frequency than the firing frequency of individual neurons. A well-known example of macroscopic neural oscillations is alpha activity.

<span class="mw-page-title-main">Arnold tongue</span> Phenomenon in maths

In mathematics, particularly in dynamical systems, Arnold tongues are a pictorial phenomenon that occur when visualizing how the rotation number of a dynamical system, or other related invariant property thereof, changes according to two or more of its parameters. The regions of constant rotation number have been observed, for some dynamical systems, to form geometric shapes that resemble tongues, in which case they are called Arnold tongues.

In serial communication of digital data, clock recovery is the process of extracting timing information from a serial data stream itself, allowing the timing of the data in the stream to be accurately determined without separate clock information. It is widely used in data communications; the similar concept used in analog systems like color television is known as carrier recovery.

In the study of chronobiology, entrainment occurs when rhythmic physiological or behavioral events match their period to that of an environmental oscillation. It is ultimately the interaction between circadian rhythms and the environment. A central example is the entrainment of circadian rhythms to the daily light–dark cycle, which ultimately is determined by the Earth's rotation. Exposure to certain environmental stimuli will cue a phase shift, and abrupt change in the timing of the rhythm. Entrainment helps organisms maintain an adaptive phase relationship with the environment as well as prevent drifting of a free running rhythm. This stable phase relationship achieved is thought to be the main function of entrainment.

<span class="mw-page-title-main">Wilberforce pendulum</span> Coupled mechanical oscillator

A Wilberforce pendulum, invented by British physicist Lionel Robert Wilberforce around 1896, consists of a mass suspended by a long helical spring and free to turn on its vertical axis, twisting the spring. It is an example of a coupled mechanical oscillator, often used as a demonstration in physics education. The mass can both bob up and down on the spring, and rotate back and forth about its vertical axis with torsional vibrations. When correctly adjusted and set in motion, it exhibits a curious motion in which periods of purely rotational oscillation gradually alternate with periods of purely up and down oscillation. The energy stored in the device shifts slowly back and forth between the translational 'up and down' oscillation mode and the torsional 'clockwise and counterclockwise' oscillation mode, until the motion eventually dies away.

In the physics of coupled oscillators, antiresonance, by analogy with resonance, is a pronounced minimum in the amplitude of an oscillator at a particular frequency, accompanied by a large, abrupt shift in its oscillation phase. Such frequencies are known as the system's antiresonant frequencies, and at these frequencies the oscillation amplitude can drop to almost zero. Antiresonances are caused by destructive interference, for example between an external driving force and interaction with another oscillator.

Microelectromechanical system oscillators are devices that generate highly stable reference frequencies used to sequence electronic systems, manage data transfer, define radio frequencies, and measure elapsed time. The core technologies used in MEMS oscillators have been in development since the mid-1960s, but have only been sufficiently advanced for commercial applications since 2006. MEMS oscillators incorporate MEMS resonators, which are microelectromechanical structures that define stable frequencies. MEMS clock generators are MEMS timing devices with multiple outputs for systems that need more than a single reference frequency. MEMS oscillators are a valid alternative to older, more established quartz crystal oscillators, offering better resilience against vibration and mechanical shock, and reliability with respect to temperature variation.

<span class="mw-page-title-main">Phase resetting in neurons</span> Behavior observed in neurons

Phase resetting in neurons is a behavior observed in different biological oscillators and plays a role in creating neural synchronization as well as different processes within the body. Phase resetting in neurons is when the dynamical behavior of an oscillation is shifted. This occurs when a stimulus perturbs the phase within an oscillatory cycle and a change in period occurs. The periods of these oscillations can vary depending on the biological system, with examples such as: (1) neural responses can change within a millisecond to quickly relay information; (2) In cardiac and respiratory changes that occur throughout the day, could be within seconds; (3) circadian rhythms may vary throughout a series of days; (4) rhythms such as hibernation may have periods that are measured in years. This activity pattern of neurons is a phenomenon seen in various neural circuits throughout the body and is seen in single neuron models and within clusters of neurons. Many of these models utilize phase response (resetting) curves where the oscillation of a neuron is perturbed and the effect the perturbation has on the phase cycle of a neuron is measured.

The terms hold-in range, pull-in range, and lock-in range are widely used by engineers for the concepts of frequency deviation ranges within which phase-locked loop-based circuits can achieve lock under various additional conditions.

William F. Egan was well-known expert and author in the area of PLLs. The first and second editions of his book Frequency Synthesis by Phase Lock as well as his book Phase-Lock Basics are references among electrical engineers specializing in areas involving PLLs.

References

  1. ↑ http://phys.org/news/2016-03-huygens-pendulum-synchronization.html - Researchers prove Huygens was right about pendulum synchronization
  2. ↑ Tiebout, M. (2004). "A CMOS direct injection-locked oscillator topology as high-frequency low-power frequency divider". IEEE Journal of Solid-State Circuits. 39 (7). Institute of Electrical and Electronics Engineers (IEEE): 1170–1174. Bibcode:2004IJSSC..39.1170T. doi:10.1109/jssc.2004.829937. ISSN   0018-9200. S2CID   31382407.
  3. ↑ De Matos, M.; Bégueret, J-B.; Lapuyade, H.; Belot, D.; Escotte, L.; Deval, Y. (2005). A 0.25 μm SiGe receiver front-end for 5GHz applications. SBMO/IEEE MTT-S International Conference on Microwave and Optoelectronics. Institute of Electrical and Electronics Engineers (IEEE). pp. 213–217. doi:10.1109/imoc.2005.1579980. ISBN   0-7803-9341-4.
  4. ↑ Gabara, T. (1999). An 0.25μm CMOS injection locked 5.6Gb/s clock and data recovery cell. Symposium on Integrated Circuits and Systems Design. pp. 84–87. doi:10.1109/SBCCI.1999.802973.
  5. ↑ Lee, J.; Liu, M. (2007). A 20Gb/s burst-mode CDR circuit using injection-locking technique. International Solid-State Circuits Conference (ISSCC). Institute of Electrical and Electronics Engineers (IEEE). pp. 46–47. doi:10.1109/ISSCC.2007.373580.
  6. ↑ Hong, B.; Hajimiri, A. (2019). "A general theory of injection locking and pulling in electrical oscillators—Part I: Time-synchronous modeling and injection waveform design". IEEE Journal of Solid-State Circuits. 54 (8). Institute of Electrical and Electronics Engineers (IEEE): 2109–2121. Bibcode:2019IJSSC..54.2109H. doi:10.1109/JSSC.2019.2908753. S2CID   198356617.
  7. ↑ Bennett, Matthew; Schatz, Michael F.; Rockwood, Heidi; Wiesenfeld, Kurt (2002-03-08). "Huygens's clocks". Proceedings of the Royal Society of London. Series A: Mathematical, Physical and Engineering Sciences. 458 (2019). The Royal Society: 563–579. Bibcode:2002RSPSA.458..563.. doi:10.1098/rspa.2001.0888. ISSN   1364-5021. S2CID   6482041.
  8. ↑ Pantaleone, James (2002). "Synchronization of metronomes". American Journal of Physics. 70 (10). American Association of Physics Teachers (AAPT): 992–1000. Bibcode:2002AmJPh..70..992P. doi:10.1119/1.1501118. ISSN   0002-9505.
  9. ↑ Watch the synchronization of 32 metronomes CBS News, 2013 Sept 10
  10. ↑ Goldsztein, Guillermo H.; English, Lars Q.; Behta, Emma; Finder, Hillel; Nadeau, Alice N.; Strogatz, Steven H. (2022-04-01). "Coupled metronomes on a moving platform with Coulomb friction". Chaos: An Interdisciplinary Journal of Nonlinear Science. 32 (4): 043119. arXiv: 2201.06161 . Bibcode:2022Chaos..32d3119G. doi:10.1063/5.0085216. ISSN   1054-1500. PMID   35489851. S2CID   246015335.
  11. ↑ Ermentrout, G. B.; Rinzel, J. (1984-01-01). "Beyond a pacemaker's entrainment limit: phase walk-through". American Journal of Physiology. Regulatory, Integrative and Comparative Physiology. 246 (1). American Physiological Society: R102–R106. doi:10.1152/ajpregu.1984.246.1.r102. ISSN   0363-6119. PMID   6696096.
  12. ↑ Mainen, Z.; Sejnowski, T. (1995-06-09). "Reliability of spike timing in neocortical neurons". Science. 268 (5216). American Association for the Advancement of Science (AAAS): 1503–1506. Bibcode:1995Sci...268.1503M. doi:10.1126/science.7770778. ISSN   0036-8075. PMID   7770778.
  13. ↑ Mori, Toshio; Kai, Shoichi (2002-05-10). "Noise-Induced Entrainment and Stochastic Resonance in Human Brain Waves". Physical Review Letters. 88 (21). American Physical Society (APS): 218101. Bibcode:2002PhRvL..88u8101M. doi:10.1103/physrevlett.88.218101. ISSN   0031-9007. PMID   12059504.
  14. ↑ Butzin, Nicholas C.; Hochendoner, Philip; Ogle, Curtis T.; Hill, Paul; Mather, William H. (2015-11-12). "Marching along to an Offbeat Drum: Entrainment of Synthetic Gene Oscillators by a Noisy Stimulus". ACS Synthetic Biology. 5 (2). American Chemical Society (ACS): 146–153. doi:10.1021/acssynbio.5b00127. ISSN   2161-5063. PMID   26524465.

Further reading

* Wolaver, Dan H. 1991. Phase-Locked Loop Circuit Design, Prentice Hall, ISBN   0-13-662743-9, pages 95–105

* Lee, Thomas H. 2004. The Design of CMOS Radio-Frequency Integrated Circuits, Cambridge, ISBN   0-521-83539-9, pages 563–566

This page is based on this Wikipedia article
Text is available under the CC BY-SA 4.0 license; additional terms may apply.
Images, videos and audio are available under their respective licenses.