Kelmark Engineering

Last updated
Kelmark GT KelmarkGT.jpg
Kelmark GT

Kelmark Engineering was an American automotive specialty shop established in 1969 and based in Okemos, Michigan. It focused on high-performance custom V8 drivetrain swaps, the modification and production of rear and mid-engined cars, and custom-built turn-key automobiles (the Kelmark GT). Until 1986, Kelmark Engineering manufactured kits and complete, finished, turn-key vehicles which were either Volkswagen-based or built on tubular race car-type frames. The outfit gained its name from Jim Kellison [1] and Randy Markham, the two co-creators who started the operation. Up until at least 1989, the Kelmark GT was still available as a kit albeit the manufacturer was Kelmark Motors in Holt, Michigan. The cars are all "rare" models, but the Volkswagen-powered Kelmark GT was the most popular.

Contents

Models

Kelmark Sleeper

Early on Kelmark gained a reputation as an innovator starting with V8 conversions for Volkswagen Beetles and Chevrolet Corvairs. They produced a unique car for the time period: a V8-powered Volkswagen Beetle. [2] It was marketed as the Sleeper, and was meant to look like a stock Beetle. It was this style chassis that the original Kelmark GT Coupe was designed around.

Kelmark V8-Vair

A mid-engine V8 conversion for the Chevrolet Corvair. [2] This mid-engine conversion turned the rear-engined Chevrolet Corvair transaxle around 180 degrees and used a special bell housing and input shaft to bolt the V8 where the stock air-cooled engine would normally be connected. This makes the rotation of the differential backwards.

The main advantage of the Kelmark Conversion is increased power and good engine placement in terms of weight distribution. The setup has a 40/60 front to rear weight distribution ratio. The main disadvantage of the Kelmark Conversion is that it requires rotating the transaxle 180° in the flat plane, and connecting it to the engine with a bell housing adapter. A stronger shaft is needed to withstand the torque of the V8 engine. Also, since the ring gear turns backwards it requires a free flow oil system or a reverse cut ring and pinion gear set. They also required a heavy duty differential or differential modifications. The Corvair differential was not designed to handle more than 250 hp (190 kW). When you put the power and torque of even a mild V8 to the stock differential, it tries to split the case from the pinion gear being forced against the ring gear.

In the early days, Crown created a modified Volkswagen differential carrier by adding two extra pinion gears to the existing two gears which in effect lessened the load and made the differentials last longer. It was called a Beef-a-diff. When Corvair transaxles started to be used in high performance applications the differential again being a weak spot was modified by adding two more pinion gears. This created a cross legged look whence the "spider" nickname was derived.

Back then a CIDCO transaxle could be purchased, this stands for Corvair Improvement Distributing Company as owned by Bob Anderson. At one time he developed Corvair transaxles with many improvements, not only for Corvairs but the kit car industry as well. Bob improved the longevity of the differentials through many modifications, re-manufacture and re-engineering, along with careful assembly. This included having reverse cut ring and pinion gears made for the Kelmark transaxle setup which ran in reverse. His setup was in great demand by the mid-engine Corvair enthusiasts. One of the trademarks of the CIDCO diff is the shoulder bolted steel plate cover on top of the differential in place of the tin cover.

Kelmark 1 GT

Initially constructed as a V8 engine special. The car had exterior styling that was distinctive for its debut in the beginning of 1974. The style of the Kelmark 1 GT Coupe was copied directly from a Dino 206 / 246.

Kelmark II GT

In late 1974 Kelmark Engineering decided to adapt it to fit the Type 1 Volkswagen Beetle chassis. This revised car was introduced as the Kelmark II. The Kelmark 1 GT Coupe was partially restyled into the Kelmark II utilizing styling cues from the experimental Two Rotor Corvette to make production easier/cheaper/better. [3] The Kelmark II had a large in-set hood scoop. The Kelmark GT went back to the smooth hood similar to what it used before on the Kelmark 1 GT.

Kelmark GT

Rear view of a V8-engined Kelmark GT Kelmark GT with a V8.jpg
Rear view of a V8-engined Kelmark GT

The next model iteration after the Kelmark II GT. The Kelmark GT was featured in the magazine Car and Driver in 1977 [4] and 1979. [5] The final body design of the Kelmark GT, as well as the Kelmark II, was 5 inches wider than an original Ferrari-built Dino 246 GTS in order to allow it to fit over a VW chassis. The windshield came from a Ford Pinto, and the side glass was the rear windows of a Chevrolet Caprice/Impala turned backwards. The Kelmark GT was offered in the following packages and could be ordered as a basic kit, partially assembled, or turn-key automobile:

Kelmark GT Independence

A fiberglass body kit for a Standard Volkswagen Beetle chassis using a VW or Porsche Type 4 engine. Many used Hot Rod VW engines such as the 1679, 1835, 1915, 2076 and 2332cc displacement engines with twin carburetors for 'mild' to 'wild' performance increases. A few also utilized the Porsche 356 and Porsche 912 engines.

Kelmark GTS

The same as the Kelmark GT Independence except it was finished in metallic silver. Most had the optional rear high-rise scoop installed at the factory. This allowed clearance to install a Buick 231 Cubic inch V6 using an engine adapter to fit the VW transaxle, such as those sold by Kennedy Engineering.

Kelmark GT Liberator

More customized, and could be mounted on a tube frame, Porsche or heavily modified VW chassis or even a custom combination with Mazda Rotary, Chevy Corvair, Porsche 6, Buick V6 or small-block V8 power. [2] It is estimated that only 200 Kelmark GTs were built as Liberator cars.

Kelmark GT Chairman

A fully loaded Kelmark GT with all luxury options such as leather interior, air conditioning, and high-end stereo equipment as offered by "Kelmark Motors" in Holt, Michigan. The cars were mostly powered by a rear engine, Buick 3.8 litre V6. This caused the car to be tail end heavy; which, unfortunately affected the handling of the car.

Kelmark Toronado GT

A big-block V8 "Super Car" utilizing a custom tube frame to accept an Oldsmobile Toronado drive unit mounted in the mid-engine position driving the rear wheels. Typically, these rare GTs were powered by the Olds 425 or 455 cubic inch (7.5 litre) engine. One of these models was outfitted with a highly tuned, Chevrolet big-block 454 cubic inch engine and was tested by Car and Driver and broke the 200 mph barrier. Thus, becoming the world's fastest street-legal sports car in 1977. Car & Driver reported this as the “Fastest documented speed ever attained by a street machine”, clocked at 202.7 by Car & Driver at the former Transportation Research Center in Ohio (now a part of Honda's US test facility). This proved the cars advanced aerodynamic and performance capabilities.

Bill Porterfield, a former Oldsmobile engineer, was responsible for the record breaking car. Later, he was the design engineer at GM for the Pontiac Fiero. He used a custom tubular frame built by his company Mid-Engineering. This special chassis utilized the Oldsmobile Toronado Turbo-Hydamatic 425 transaxle behind a 700 hp Chevrolet ZL-1, 454 big-block motor. The Mid-Engineering chassis used Chevrolet Corvette rear suspension arms and custom half shafts to allow wide performance tires. To put this accomplishment into perspective one should consider that it took Ferrari until March 1987 to come out with a 200 mph street legal sports car, the Ferrari F40. The F40 was a low production volume special which was not a mainstream Ferrari. Just a few months later Road and Track tested several specialty sports cars. The Ruf CTR Porsche 911 Yellow Bird and the Koenig RS Porsche 911; which, broke 200 mph. These two ran at 211 and 201 mph, respectively. Again, these were low volume custom sports cars. In these same tests, which were completed by Road and Track, with Le Mans winning Paul Frere and Formula One champ Phil Hill driving, the Ferrari Testarossa, Lamborghini Countach 5000S and AMG Hammer Mercedes-Benz 300E all failed to break 200 mph.

Related Research Articles

<span class="mw-page-title-main">Porsche 924</span> German sports car built 1976–1988

The Porsche 924 is a sports car produced by Porsche in Neckarsulm, Germany, from 1976 until 1988. A two-door, 2+2 coupé, the 924 replaced the 912E and 914 as the company's entry-level model.

<span class="mw-page-title-main">Porsche Cayenne</span> German luxury crossover SUV

The Porsche Cayenne is a series of automobiles manufactured by the German company Porsche since 2002. It is a luxury crossover SUV, and has been described as both a full-sized and a mid-sized vehicle. The first generation was known within Porsche as the Type 9PA (955/957) or E1. It was the first V8-engined vehicle built by Porsche since 1995, when the Porsche 928 was discontinued. It is also Porsche's first off-road variant vehicle since its Super and Junior tractors of the 1950s, as well as the first production Porsche with four doors. Since 2014, the Cayenne has been sold alongside a smaller Porsche SUV, the Macan.

<span class="mw-page-title-main">Chevrolet Corvair</span> Compact automobile

The Chevrolet Corvair is a rear-engined, air-cooled compact car manufactured and marketed by Chevrolet over two generations between 1960 and 1969. A response to the Volkswagen Beetle, it was offered in 4-door sedan, 2-door coupe, convertible, 4-door station wagon, passenger van, commercial van, and pickup truck body styles in its first generation (1960–1964), and as a 2-door coupe, convertible or 4-door hardtop in its second (1965–1969). Total production was approximately 1.8 million vehicles from 1960 until 1969.

Reva was a series of cars made by Dan Werbin and Holger Brånby at Reva gård in Sweden in the mid-1960s. They were two seated coupé mid engined sports cars. The first one built in 1964, the Reva GT, was made with a fibreglass body on a VW Beetle chassis. It was followed by the Reva GT Mk1 powered with a VW 1200 engine and fitted with Porsche brakes. Three Mk1s were made. The Mk II model had more rounded shapes, but still used the VW Beetle chassis. The company produced and sold about 20 bodies, but no complete cars. For the 1968 Mk III they wanted to produce a more finished car. The body was made lower and wider and they no longer used the Beetle chassis, but had a custom made chassis made of steel tubes. The prototype was powered by a 3.5 litre Buick V8, the next was fitted with a 5.4 litre Chevrolet Corvette engine and number three had a 5.41 litre Oldsmobile V8. Then the rules for amateur built vehicles in Sweden changed and they had to end production.

<span class="mw-page-title-main">Panoz Esperante</span> Motor vehicle

The Esperante is a sports car made by Panoz, an American car manufacturer.

<span class="mw-page-title-main">Rear-engine, rear-wheel-drive layout</span> Automotive design

In automotive design, an RR, or rear-engine, rear-wheel-drive layout places both the engine and drive wheels at the rear of the vehicle. In contrast to the RMR layout, the center of mass of the engine is between the rear axle and the rear bumper. Although very common in transit buses and coaches due to the elimination of the drive shaft with low-floor buses, this layout has become increasingly rare in passenger cars.

<span class="mw-page-title-main">Transaxle</span> Combined transmission, axle and differential in one assembly.

A transaxle is a single mechanical device which combines the functions of an automobile's transmission, axle, and differential into one integrated assembly. It can be produced in both manual and automatic versions.

<span class="mw-page-title-main">Engine swap</span>

In car tuning culture, an engine swap is the process of removing a car's original engine and replacing it with another. This may be a like-for-like replacement, or to install a non-factory specification engine. Typically, an engine swap is performed for performance, swapping-in a more powerful engine; however, an engine swap may also be performed for maintenance, where older engines may have a shortage of spare parts, and so a modern replacement may be more easily and cheaply maintained.

<span class="mw-page-title-main">Ferrari 275</span> Motor vehicle

The Ferrari 275 is a series of front-engined V12-powered grand touring automobiles with two-seater coupé and spider bodies produced by Ferrari between 1964 and 1968. The first 275 series cars were powered by a 3.3 L (3286 cc) overhead camshaft Colombo 60° V12 engine producing 260–320 hp (190–240 kW). An updated 275 GTB/4 was introduced in 1966, with a revised four overhead camshaft engine producing 300 hp (220 kW). The 275 series were the first road-going Ferraris equipped with a transaxle and independent rear suspension.

<span class="mw-page-title-main">Ferrari 550</span> Grand tourer produced by Ferrari

The Ferrari 550 Maranello is a front-engine V12 2-seat grand tourer built by Ferrari from 1996 to 2002. The 550 Maranello marked Ferrari's return to a front-engine, rear-wheel drive layout for its 2-seater 12-cylinder model, 23 years after the 365 GTB/4 Daytona had been replaced by the mid-engined Berlinetta Boxer.

<span class="mw-page-title-main">Chevrolet Turbo-Air 6 engine</span> Reciprocating internal combustion engine

The Chevrolet Turbo-Air 6 is a flat-six air-cooled automobile engine developed by General Motors (GM) in the late 1950s for use in the rear-engined Chevrolet Corvair of the 1960s. It was used in the entire Corvair line, as well as a wide variety of other applications.

<span class="mw-page-title-main">Morgan Aero 8</span> English sports car model

The Morgan Aero 8 is a sports car built by Morgan Motor Company at its factory in Malvern Link, England from 2000 until 2018.

<span class="mw-page-title-main">Hewland</span> British engineering company

Hewland is a British engineering company, founded in 1957 by Mike Hewland, which specialises in racing-car gearboxes. Hewland currently employ 130 people at their Maidenhead facility and have diversified into a variety of markets being particularly successful in electric vehicle transmission supply.

<span class="mw-page-title-main">Fiberfab Avenger GT</span> Motor vehicle

The Avenger GT was a kit car produced by Fiberfab. It was designed in California and manufactured in the United States and Canada for 12 years, from late 1966 until 1978.

<span class="mw-page-title-main">Fiberfab Valkyrie</span> Motor vehicle

The Valkyrie is a GT sports car introduced in 1966 by the Fiberfab company. The Valkyrie's styling was inspired by the lines of the Ford GT40.

Manta Cars was owned and operated by American brothers Brad and Tim LoVette, and was located in Costa Mesa, California, from 1974 to 1986. Manta produced the Manta Mirage, and later produced other component kit cars, including the rear-engined Volkswagen Beetle-based Manta Montage, and the mid-engined Montage-T, which had a custom space frame chassis and used GM X-body V6 drivetrains. The Montage-T recreated the elusive McLaren M6GT.

<span class="mw-page-title-main">Devin Enterprises</span> American automotive manufacturer

Devin Enterprises was an American automotive manufacturer that operated from 1955 to 1964. Devin was mainly known for producing high quality fiberglass car bodies that were sold as kits, but they also produced automotive accessories as well as complete automobiles. The company was founded by Bill Devin.

<span class="mw-page-title-main">Corvair Powerglide</span> Automatic transmission

Chevrolet Corvair Powerglide is a two-speed automatic transmission designed specially for the then all-new 1960 Chevrolet Corvair compact car that emerged in the fall of 1959 as Chevrolet's competitor in the then booming small car market. The Corvair was powered by a rear-mounted Chevrolet Turbo-Air 6 engine that necessitated a specially designed transaxle. Corvair Powerglide took the principles of the standard Chevrolet Powerglide and modified them to suit the rear-mounted powertrain location of the new Corvair. The Corvair used the Powerglide for all 10 years it was produced; from 1961 to 1963, Pontiac used a modified version of Corvair Powerglide it called 'TempesTorque' for its front-engine, rear-transaxle Tempest, LeMans and Tempest LeMans cars.

Fiberfab was an American automotive manufacturer established in 1964. Starting with accessories and body parts, they progressed to making kit cars and fully assembled automobiles. They became one of the longest lasting kit car manufacturers.

<span class="mw-page-title-main">Lola Mk6</span> British racing car

The Lola Mk6 GT was a racing car with a production run of only three units, built between 1962 and 1963 by British car manufacturer Lola Cars. With its 289 cu in (4.74 L) Ford V8 engine, the Mk6 GT was the first mid-mounted, high displacement V8-powered Grand Touring car, a chassis arrangement that had been used, up until that time, only on formula cars and smaller, more affordable GTs.

References

  1. "History of the Kelmark Kit Car". Archived from the original on 2007-10-20.
  2. 1 2 3 Company marketing brochure, scanned copy available here and here.
  3. "Kelmark History at Bugoholics" Archived 2007-10-20 at the Wayback Machine
  4. Car and Driver , November 1977.
  5. "Going for it", Car and Driver, 1979.