Layshaft

Last updated
Sectioned 3-speed manual 'crash' gearbox, for a car c. 1935 Gearbox (Autocar Handbook, 13th ed, 1935).jpg
Sectioned 3-speed manual 'crash' gearbox, for a car c. 1935

A layshaft is an intermediate shaft within a gearbox that carries gears, but does not transfer the primary drive of the gearbox either in or out of the gearbox. [1] [2] Layshafts are best known through their use in car gearboxes, where they were a ubiquitous part of the rear-wheel drive layout. With the shift to front-wheel drive, the use of layshafts is now rarer.

Contents

The driving shaft carries the input power into the gearbox. The driven shaft is the output shaft from the gearbox. In car gearboxes with layshafts, these two shafts emerge from opposite ends of the gearbox, which is convenient for RWD cars but may be a disadvantage for other layouts. [3]

For gearboxes in general, gear clusters [lower-roman 1] mounted on a layshaft may either turn freely on a fixed shaft, or may be part of a shaft that then rotates in bearings. There may be multiple separate clusters on a shared shaft and these are allowed to turn freely relative to each other. [lower-roman 2]

Origins

The term layshaft originates with watermill machinery. The layshaft is the gear-carrying shaft that links the wallower (the small spur gear driven at increased speed by the waterwheel) to any upright shafts that carry the millstones. The term, layshaft, was also used by millwrights, in both wind- and watermills, to refer to a shaft that drove secondary machinery such as sack hoists, rather than the main milling machinery.

The term layshaft was also applied to back-geared lathes. These were lathes with a slow-speed mechanism in addition to their usual belt drive. This used two gears on a layshaft behind the headstock, giving a double reduction gear.

Car manual transmissions

In the typical manual gearbox for a RWD car, the driving shaft (input) is in-line with the driven shaft (output), but not permanently connected to it. A reduction gear on the driving shaft drives the layshaft. In car transmissions, the term countershaft is also used. [4] A number of gears on the layshaft may then be connected, one at a time, to the driven shaft. Selecting each of these gears in turn gives the various ratios of the gearbox. [5] All of these gear ratios are reduction gears, the engine speed being higher than the input speed to the final drive of the rear axle.

Early gearboxes used sliding gears to engage and disengage the drive. These were difficult to operate and also wore on the main working surfaces of the gears. An early improvement was to use separate dog clutches instead to engage gears, leaving the gears themselves in 'constant mesh'. A later, and more gradual development, was the introduction of synchromesh. This is an all-metal friction clutch in addition to the positive dog clutch, that gradually engages the gears and matches their speed before the dog clutch engages. [6]

The top gear of the gearbox is achieved without these gears, but by coupling the driven shaft directly to the driving shaft through another dog clutch. This gives a 'direct drive' top gear, which has advantages for both efficiency and quietness at cruising speed. A typical gearbox had 2% losses in each gear set, so 4% for intermediate ranges through their two gears, but approaching 0% for the direct-drive top gear. [3] As the direct top gear is not transmitting torque through the gears, it is also quieter.

In theory, it is also possible to provide an overdrive top gear, another indirect gear, but of a speed-up ratio rather than the reduction ratio of the other gears. The direct-drive ratio then becomes the second-to-top or third gear. This arrangement was used on some early cars, but was uncommon. [3] Where overdrive is provided for a RWD car, this is almost always done by adding a separate overdrive gearbox to the output driven shaft of the gearbox, usually outside the gear casing. [7]

Because of the layout of the gearbox, the layshaft is normally mounted low-down in the gearbox casing below the other shafts. The gear lever enters through the top of the casing and so it is more convenient for the sliding components of the dog clutches to be mounted on the driven shaft, rather than the layshaft. The layshaft gear cluster is thus often a simple one-piece component, typically cast iron gears running in bearings on a fixed steel shaft. The bearings may be plain phosphor bronze bushes, or for high-load applications needle rollers. [4]

Where large numbers of gear ratios, six or more, are to be provided then these will require a third or more gear clusters on the layshaft. [lower-roman 3] To maintain the proportions of the overall gearbox as more compact, rather than becoming long and thin, these gearboxes may use twin layshafts. This requires an additional driven gear for each layshaft, but the mechanism is otherwise very similar. The use of multiple layshafts also developed into the multiple clutch gearbox, used for some buses, where each ratio has its own layshaft and separate plate or hydraulic clutches, rather than dog clutches, are used to select between them. [8]

Where a power take-off is required, usually for industrial vehicles to drive winches, hydraulic pumps etc., this is often driven from one end of the layshaft, as this is more accessible shaft than the main shafts, already in use by the drivetrain.

'All-indirect' gearboxes

Early, pre-1911, all-indirect gearbox Gearbox retouched.png
Early, pre-1911, all-indirect gearbox

Some gearboxes do not use a layshaft, but rely on indirect gears throughout. [3]

All-indirect were used for some very early cars, before the advantages of the direct-drive top gear were recognised. They contain no dog clutches; at the time, gear changing was still carried out by sliding the gears in and out of mesh. Once the dog clutch came into use, the further advantage of a direct-drive top gear was immediately recognised.

FWD all-indirect manual gearbox, with final drive taken from the second shaft Manual Transmission for Volkswagen Golf.jpg
FWD all-indirect manual gearbox, with final drive taken from the second shaft

With the popularity of front-wheel drive from the 1960s, the all-indirect gearbox has become common. These have been used for both transverse engine layouts, where the offset of two shafts is more convenient than the in-line arrangement of a layshaft gearbox, [9] and for longitudinal transaxle designs, such as the VW Beetle or many Renaults, [lower-roman 4] where the requirement was to have both driven and driving shafts at the same end of the gearbox.

Although the loss of the direct-drive top ratio loses the ability for 0% losses when cruising, this is compensated for by reducing losses in other ratios from 4% to 2%. [lower-roman 5] [3] Noise is also reduced by modern metallurgy and gear cutting, which give quieter and more efficient gear profiles.

As the gearbox efficiency remains constant for all ratios of an all-indirect gearbox, it is now convenient to provide overdrive top gears, even when these are no longer direct-drive or 1:1 ratios. One of the first mass-market cars to offer such a feature was the VW Polo and the Formel E, with a deliberately-labelled '-E' for 'economy' overdrive ratio.

See also

Related Research Articles

<span class="mw-page-title-main">Clutch</span> Mechanical device that connects and disconnects two rotating shafts or other moving parts

A clutch is a mechanical device that engages and disengages power transmission, especially from a drive shaft to a driven shaft. In the simplest application, clutches connect and disconnect two rotating shafts. In these devices, one shaft is typically attached to an engine or other power unit, while the other shaft provides output power for work. Typically the motions involved are rotary, but linear clutches also exist.

Differential (mechanical device) Type of simple planetary gear train

A differential is a gear train with three drive shafts that has the property that the rotational speed of one shaft is the average of the speeds of the others, or a fixed multiple of that average.

<span class="mw-page-title-main">Automatic transmission</span> Type of motor vehicle transmission that automatically changes gear ratio as the vehicle moves

An automatic transmission is a multi-speed transmission used in internal combustion engine-based motor vehicles that does not require any driver input to change forward gears under normal driving conditions. It typically includes a transmission, axle, and differential in one integrated assembly, thus technically becoming a transaxle.

Overdrive (mechanics) Operation of an automobile cruising at sustained speed with reduced engine revolutions

Overdrive is the operation of an automobile cruising at sustained speed with reduced engine revolutions per minute (RPM), leading to better fuel consumption, lower noise, and lower wear. The term is ambiguous. The most fundamental meaning is that of an overall gear ratio between engine and wheels, such that the car is over-geared, and cannot reach its potential top speed, i.e. the car could travel faster if it were in a lower gear, with the engine turning at higher RPM.

<span class="mw-page-title-main">Propulsion transmission</span> Drivetrain transmitting propulsion power

Propulsion transmission is the mode of transmitting and controlling propulsion power of a machine. The term transmission properly refers to the whole drivetrain, including clutch, gearbox, prop shaft, differential, and final drive shafts. In the United States the term is sometimes used in casual speech to refer more specifically to the gearbox alone, and detailed usage differs. The transmission reduces the higher engine speed to the slower wheel speed, increasing torque in the process. Transmissions are also used on pedal bicycles, fixed machines, and where different rotational speeds and torques are adapted.

<span class="mw-page-title-main">Manual transmission</span> Motor vehicle manual gearbox; stick shift

A manual transmission (MT), also known as manual gearbox, standard transmission, or stick shift, is a multi-speed motor vehicle transmission system, where gear changes require the driver to manually select the gears by operating a gear stick and clutch.

Freewheel Mechanism which disconnects a driveshaft from a faster-rotating driven shaft

In mechanical or automotive engineering, a freewheel or overrunning clutch is a device in a transmission that disengages the driveshaft from the driven shaft when the driven shaft rotates faster than the driveshaft. An overdrive is sometimes mistakenly called a freewheel, but is otherwise unrelated.

Drive shaft Mechanical component for transmitting torque and rotation

A drive shaft, driveshaft, driving shaft, tailshaft, propeller shaft, or Cardan shaft is a component for transmitting mechanical power and torque and rotation, usually used to connect other components of a drivetrain that cannot be connected directly because of distance or the need to allow for relative movement between them.

TorqueFlite Automotive part

TorqueFlite is the trademarked name of Chrysler Corporation's automatic transmissions, starting with the three-speed unit introduced late in the 1956 model year as a successor to Chrysler's two-speed PowerFlite. In the 1990s, the TorqueFlite name was dropped in favor of alphanumeric designations, although the latest Chrysler eight-speed automatic transmission has revived the name.

<span class="mw-page-title-main">Direct-shift gearbox</span> Type of dual-clutch transmission

A direct-shift gearbox is an electronically-controlled, dual-clutch, multiple-shaft, automatic gearbox, in either a transaxle or traditional transmission layout, with automated clutch operation, and with fully-automatic or semi-manual gear selection. The first dual-clutch transmissions were derived from Porsche in-house development for the Porsche 962 in the 1980s.

Preselector gearbox Type of manual transmission

A preselector gearbox is a type of manual transmission mostly used on passenger cars and racing cars in the 1930s, in buses from 1940-1960 and in armoured vehicles from the 1930s to the 1970s. The defining characteristic of a preselector gearbox is that the gear shift lever allowed the driver to "pre-select" the next gear, usually with the transmission remaining in the current gear until the driver pressed the "gear change pedal" at the desired time.

ATTESA is a four-wheel drive system used in some automobiles produced by the Japanese automaker Nissan, including some models under its luxury marque Infiniti.

<span class="mw-page-title-main">Gear stick</span> Lever used for shifting gears manually

A gear stick, gear lever, gearshift or shifter, more formally known as a transmission lever, is a metal lever attached to the transmission of an automobile. The term gear stick mostly refers to the shift lever of a manual transmission, while in an automatic transmission, a similar lever is known as a gear selector. A gear stick will normally be used to change gear whilst depressing the clutch pedal with the left foot to disengage the engine from the drivetrain and wheels. Automatic transmission vehicles, including hydraulic automatic transmissions, automated manual and older semi-automatic transmissions, like VW Autostick, and those with continuously variable transmissions, do not require a physical clutch pedal.

<span class="mw-page-title-main">Non-synchronous transmission</span> Form of manual transmission

A non-synchronous transmission, also called a crash gearbox, is a form of manual transmission based on gears that do not use synchronizing mechanisms. They require the driver to manually synchronize the transmission's input speed and output speed.

Jackshaft

A jackshaft, also called a countershaft, is a common mechanical design component used to transfer or synchronize rotational force in a machine. A jackshaft is often just a short stub with supporting bearings on the ends and two pulleys, gears, or cranks attached to it. In general, a jackshaft is any shaft that is used as an intermediary transmitting power from a driving shaft to a driven shaft.

Twin Clutch SST is the brand name of a six-speed dual-clutch automatic transmission, developed by Getrag for Mitsubishi Motors. The system was first incorporated in the 2008 Lancer Evolution X, and was designed to be a more performance-oriented system than that developed by rival manufacturers, with shorter gear ratios optimized for acceleration.

Hele-Shaw clutch

The Hele-Shaw clutch was an early form of multi-plate wet clutch, in use around 1900. It was named after its inventor, Professor Henry Selby Hele-Shaw, who was noted for his work in viscosity and flows through small gaps between parallel plates. The clutch was innovative in not relying upon friction, as other clutches did.

<span class="mw-page-title-main">Dual-clutch transmission</span> Type of automatic transmission

A dual-clutch transmission (DCT) is a type of multi-speed vehicle transmission system, that uses two separate clutches for odd and even gear sets. The design is often similar to two separate manual transmissions with their respective clutches contained within one housing, and working as one unit. In car and truck applications, the DCT functions as an automatic transmission, requiring no driver input to change gears.

Motorcycle transmission Transmission for motorcycle applications

A motorcycle transmission is a transmission created specifically for motorcycle applications. They may also be found in use on other light vehicles such as motor tricycles and quadbikes, go-karts, offroad buggies, auto rickshaws, mowers, and other utility vehicles, microcars, and even some superlight racing cars.

Drivetrain Group of components that deliver power to the driving wheels

In automotive engineering, the drivetrain is the group of components of a motor vehicle that deliver power to the drive wheels. This excludes the engine or motor that generates the power.

References

Notes

  1. Pairs or more of gears, connected together.
  2. Note that this is not the case where a single transmission path at multiple speeds, such as for car gearboxes, is needed. Car gearboxes use a layshaft with all its gears coupled together.
  3. As top gear is direct-drive, even five gears only require two clusters.
  4. Including the Renault 4, 5, 12, 16, 15/17, 25 & 30
  5. Through one gear pair rather than two.

Citations

  1. Setright, L. J. K. (1976). "Gearbox". In Ian Ward (ed.). Anatomy of the Motor Car. Orbis. p. 88. ISBN   0-85613-230-6.
  2. The Autocar (c. 1935). Autocar Handbook (Thirteenth ed.). London: Iliffe & Sons.
  3. 1 2 3 4 5 Setright, Anatomy of the Motor Car , p. 92
  4. 1 2 V.A.W., Hillier (1991). "38: The sliding-mesh gearbox". Fundamentals of Motor Vehicle Technology (4th ed.). Stanley Thornes. p. 231. ISBN   0-7487-05317.
  5. Setright, Anatomy of the Motor Car , p. 88–89
  6. Setright, Anatomy of the Motor Car , p. 89–90
  7. Setright, L. J. K. (1976). "Overdrive". In Ian Ward (ed.). Anatomy of the Motor Car. Orbis. pp. 93–95. ISBN   0-85613-230-6.
  8. Bryan Jarvis (8 March 1986). "No Longer a Pandora's Box". Commercial Motor . 163 (4161): 46–47.
  9. Hillier (1991) , p. 243