| Levasseur PL.1 | |
|---|---|
 | |
| Role | Touring aircraft |
| National origin | France |
| Manufacturer | Levasseur |
| Designer | Pierre Levasseur |
| First flight | April-May 1922 |
| Number built | 1 |
Pierre Levasseur's first aircraft, the Levasseur PL.1, was a three seat tourer (French category T.O.3) with a novel, simplified structure. One of only two Levasseur powered civil designs, the sole example was completed in 1922.
The PL.1 had a wooden structure and was fabric covered. Levasseur's prime design aim was to minimize the number of components in order to reduce costs and to do that he produced a central plywood master-frame on which the other parts, principally the wings, engine, fuselage and undercarriage were mounted. The master-frame was formed from a pair of flat, streamlined sub-frames, each with short and parallel upper and lower sides, connected at their ends by two longer and slightly converging members. A cross piece about halfway up stabilised the sub-frame. The two parts were then joined at their base and separated above, with tie-bars about halfway up, into an elongated V.
The tourer was a single bay biplane with 400 mm (15.7 in) of stagger. Its wings had parallel, unswept edges and angled tips. The lower wing had a span 600 mm (23.6 in) less than the upper and only it carried ailerons, which were broad-chord and filled most of the span. The wings were supported centrally on the horizontal top and bottom members of the master-frame, with the lower wing passing under the fuselage. Interplane struts were formed by streamlined parallelogram-shaped frames which leaned both outwards and forward because of the different spans and the stagger. [1] [2]
The tourer was powered by a water-cooled Hispano-Suiza 8Ab V8 engine with its cylindrical Lamblin radiator mounted below. Its bearers were attached to the forward members of the master-frame. The unusual rear part of the fuselage, a plywood girder structure which deepened but converged in plan progressively rearwards was mounted halfway up the rear master-frame members, near the tie-bar. The girder, which carried formers and stringers to define the curved section of the upper fuselage, was braced by a long aluminium tube from its rear to the rear vertex of the master-frame. [2]
There were two open cockpits. The forward one had two side-by side seats equipped with dual controls for the pilot and passenger or pupil. They sat under the trailing edge of the upper wing where the large interplane gap provided good forward vision and a wing cut-out improved their upward view. A separate, circular cockpit behind them could be fitted with a seat for a second passenger. [1]
The empennage was conventional, with near-triangular fin and tailplane, the latter mounted on top of the fuselage girder. Early photographs and drawings [1] [2] show both carried straight-edged control surfaces, though a later photograph shows a taller, round-topped rudder. [3]
The PL.1 had conventional, steel tube landing gear with mainwheels independently mounted on a split axle hinged from the forward vertex of the lower master-frame and with radius arms to its rear. Long legs with shock absorbers joined axle ends to the master-frame as it emerged from the upper fuselage. There was a tailskid at the rear.
The tourer made its first public appearance, uncompleted, in November 1921 at that year's Paris Salon. [2] It did not fly until late April or very early May 1922, when Henri Pitot flew it for twenty minutes. [4] In the last week of May Piton displayed it at the Bourget meeting, demonstrating its good handling with an aerobatic display. The Dubonnet Cup was contested later in that meeting and Pitot was leading the field when the PL.1 experienced a breakdown in the final quarter. [5]
By December 1922 the PL.1 was featured in Levasseur advertisements. [3]
Data from Les Ailes, December 1921 [1]
General characteristics
Performance
The Levasseur PL.10 was a carrier-based reconnaissance aircraft developed in France in the late 1920s. It was a conventional, single-bay biplane along similar lines to Levasseur's contemporary designs for the French navy, including a watertight, boat-shaped fuselage, small underwing floats, and undercarriage that could be jettisoned in flight in order to improve the changes of a successful ditching.
The Potez 37 was a two-seat, long range reconnaissance aircraft built to compete for a French government contract. It flew in mid-1930 but did not win the competition, so only two were completed.
The Nieuport-Delage NiD 43 was a single engine, two seat biplane fighter aircraft designed and built for shipboard use in France in 1924.
The Hanriot HD.15 was a French two seat fighter aircraft fitted with a supercharger for good high altitude performance, built in the 1920s. Three were ordered by Japan but lost at sea during delivery.
The Hanriot H.26 was a French single seat fighter aircraft prototype completed in 1923. Only one was built.
The Potez 26 was a single seat fighter aircraft designed and flown in France in the mid-1920s. It did not reach production.
The Potez 31 was a prototype French two-seat night fighter, flown in about 1928, intended to fill the Cn.2 specification for the Armee de l'Air. Only one was built.
The Caudron C.220 was a two-seat French biplane trainer. Only two were built, using different engines.
The Caudron C.99 was a French light bomber and reconnaissance aircraft. The only example flew with different engines in the mid-1920s.
The Caudron C.97 was a two-seat biplane trainer designed and built in France around 1924. A number were used by the Bolivian Air Force.
The Caudron C.74 was a ten-seat, four engine passenger biplane built in France in 1922. It showed promise but the sole prototype crashed fatally in a competition and no more were completed.
The Caudron Type L was a two-seat French pusher configuration amphibious biplane, flown around 1913 and intended for naval use.
The Weymann W-100, Weymann CTW-100 or Weymann W-100 RBL was a French three seat observation aircraft with a position for the observer within its partially glazed fuselage. Only one was built.
The Potez 50 or Potez 50 A2 was a French two seat military multi-rôle aircraft, first flown in 1931. It did not go into service but seven variants using five different engines were produced, one of them setting several speed with useful load records and another, the Potez 506, setting three altitude world records.
The Weymann-Lepère WEL-80 R.2 was a French two seat reconnaissance aircraft built to compete for a 1928 government contract. It was not successful and did not enter production.
The Bréguet 25 or XXV was a French two seat fighter from 1925. It was heavily armed, carrying seven machine guns.
The CPA 1 was a French twin-engined, parasol-winged bomber designed and built in the mid-1920s.
The CAMS 54 was a strengthened and more powerful version of the French CAMS 51 civil transport and naval reconnaissance flying boat, developed for transatlantic flights. It is sometimes referred to as the 54 GR.
The Lumière-de Monge racer was built specifically to compete in the 1921 Coupe Deutsch de la Meurthe, flown at Etampes on 1 October 1921. As well as being fast, it was unusual in being a high wing monoplane which could be rapidly converted into a biplane by adding smaller lower wing. It crashed, fatally, before the race.
The Tampier Avion-Automobile was a French roadable aircraft designed and built by René Tampier in 1921. Only two were built.