Lime plaster

Last updated

Limestone-plastered wall discovered in Pompei Plaster - Putz in Pompeji.JPG
Limestone-plastered wall discovered in Pompei

Lime plaster is a type of plaster composed of sand, water, and lime, usually non-hydraulic hydrated lime (also known as slaked lime, high calcium lime or air lime). Ancient lime plaster often contained horse hair for reinforcement and pozzolan additives to reduce the working time.

Contents

Traditional non-hydraulic hydrated lime only sets through carbonatation when the plaster is kept moist and access of CO2 from the air is possible. It will not set when submersed in water. When a very thick layer or several layers are applied, the lime can remain soft for weeks.

The curing time of lime plaster can be shortened by using (natural) hydraulic lime or adding pozzolan additives, transforming it into artificially hydraulic lime. In ancient times, Roman lime plaster incorporated pozzolanic volcanic ash; in modern times, fly ash is preferred. Non-hydraulic lime plaster can also be made to set faster by adding gypsum.

Lime production for use in plastering home-made cisterns (in making them impermeable) was especially important in countries where rain-fall was scarce in summer. This enabled them to collect the winter run-off of rain water and to have it stored for later use, whether for personal or agricultural needs. [1]

Advantages

Lime plaster sets up to a solid mass that is durable yet flexible. [2] Hydraulic lime plaster is not as hard as cement plaster. Hydraulic limes and historic limes were graded as feeble, moderate and eminent. Modern hydraulic limes would be graded at 2, 3.5, or 5 newtons. Portland cement plaster on the other hand would typically be in the region of 25 to 35 newtons when cured; i.e. up to 10 times harder. Lime plaster is less affected by water and will not soften or dissolve like drywall and earthen or gypsum plaster. Unlike gypsum or clay plaster, lime plaster is sufficiently durable and resistant to the elements to be used for exterior plastering.

Compared to cement plaster, plaster made from hydrated lime is less brittle and less prone to cracking, requiring no expansion joints. It will not detach from the wall when subjected to shear stress due to expansion inflicted by solar radiation and moisture. Unlike cement plaster, it will shield softer materials from shear stresses. This would otherwise possibly cause the deterioration of the underlying surface. It is usually not recommended to replace more than 20% of the lime content with cement when rendering the facade, and it is a matter of contention whether adding any concrete is ever appropriate in order to maintain the benefits of lime over concrete.

Lime plaster is permeable and allows for the diffusion and evaporation of moisture. However, when properly worked with pozzolanic agents and animal fat, it becomes impermeable. [3] [4]

The elevated pH of the lime in the plaster acts as a fungicide, preventing mold from growing in lime plaster. [2] [ citation needed ]

Disadvantages

Non-hydraulic lime plaster sets slowly and is quite caustic while wet, with a pH of 12. Plasterers must take care to protect themselves or use mild acids as vinegar or lemon juice to neutralize chemical burn. [5] When the plaster is dry, the pH falls to about 8.6. Non-hydraulic lime plaster requires moisture to set and has to be prevented from drying for several days. The number of qualified tradesmen capable of plastering with lime has declined due to industrialization, deskilling of trade crafts, and widespread adoption of drywall and gypsum veneer plaster. [6] [7]

Venetian Plaster Techniques

Venetian plaster is a type of polished plaster that is widely used for wall and ceiling finishes. It consists of a mixture of plaster and marble dust, which is applied in thin layers using a spatula or trowel. The technique involves applying multiple layers of the plaster mixture and then burnishing the surface to create a smooth finish with the illusion of depth and texture.

There are various techniques that can be used to achieve different effects with Venetian plaster. Marmorino is one such technique, which involves adding marble dust to the plaster mixture to create a polished marble-like appearance. Scagliola is another technique that imitates various types of stone, while sgraffito involves scratching the surface of the plaster to reveal different layers and create decorative patterns.

When left un-burnished, Venetian plaster has a rough and stone-like matte finish. However, when applied correctly and burnished, it can result in a highly polished, rock-hard finish that resembles marble. This makes Venetian plaster an excellent alternative to expensive and heavy marble installations, as it can be used on surfaces such as columns, corbels, and curved walls.

Venetian Plaster History

The history of polished plaster can be traced back to ancient times, with evidence of its use in ancient Egyptian, Roman, and Greek architecture. The technique was highly valued for its durability and aesthetic appeal, and it has continued to be used and refined throughout history. [8] [9]

Throughout ancient times, lime was a widely employed material for constructing plaster on both interior and exterior walls. The Greeks, in particular, made a remarkable discovery regarding the production of a special adhesive by subjecting limestone rocks to intense heat within expansive ovens. [10] Nevertheless, this transformative process, which involved converting limestone into calcium oxide, carbon dioxide, and steam, posed significant challenges due to the requirement of extremely high temperatures, reaching approximately 2200 °F. The resulting substance, known as quicklime or lump-lime, was subsequently pulverized into a fine powder and combined with water in a process called "slaking." Through this procedure, a fundamental binding agent called "lime putty" was created and utilized for plastering purposes. The slaked lime, a dense and moist substance, would then be stored in a designated pit for several months, or even years, to ensure complete hydration. Historical accounts suggest that the Romans enforced a regulation stipulating that slaked lime could only be employed if it had aged for a minimum of three years. [11]

Venetian plaster, a distinctive type of wall covering, boasts a rich historical legacy that traces back to ancient times, with its origins linked to Pompeii and the subsequent Roman Empire. Vitruvius, who lived around 80-70 B.C., documented the process of manufacturing lime plaster in his renowned work "De architecture" or "Ten Books of Architecture." [12] [13] These methods were further elaborated upon by Pliny the Elder in his book "Natural History," dating back approximately 2,000 years. The Romans referred to the finished product as "Marmoratum Opus," meaning "smooth marble." The rediscovery of Venetian plaster can be attributed to the Renaissance period, characterized by a renewed interest in the ancient techniques of Rome. Palladio, a renowned Renaissance architect, referred to the process as "Pietra d'Istria" since the plaster bore a striking resemblance to natural rocks such as marble, granite, and travertine commonly found near Venice. Palladio's architectural creations, although seemingly constructed from stone, were in fact composed of brick and stucco. The plastering process involved the initial application of a coarse layer of plaster known as "arricio," followed by subsequent layers of lime putty blended with powdered marble to achieve a smooth and polished surface. On occasion, pigments were added to the wet plaster to introduce vibrant hues.

During the Baroque period, Venetian plaster experienced a decline in popularity, echoing the diminished prominence witnessed after the fall of the Roman Empire. [14] However, in the 1950s, a notable Venetian builder named Carlo Scarpa played a pivotal role in revitalizing the use of Marmorino in contemporary construction. [15] Scarpa not only adhered to the methods outlined by Vitruvius and Palladio but also introduced innovative techniques involving the utilization of animal hides and acrylic resins.

Historical use in the arts

One of the earliest examples of lime plaster dates back to the end of the eighth millennium BC. Three statues were discovered in a buried pit at 'Ain Ghazal in Jordan that were sculpted with lime plaster over armatures of reeds and twine. They were made in the pre-pottery neolithic period, around 7200 BC. [16] The fact that these sculptures have lasted so long is a testament to the durability of lime plaster. [17]

Historical uses in building

See also

Related Research Articles

<span class="mw-page-title-main">Concrete</span> Composite construction material

Concrete is a composite material composed of aggregate bonded together with a fluid cement that cures to a solid over time. Concrete is the second-most-used substance in the world after water, and is the most widely used building material. Its usage worldwide, ton for ton, is twice that of steel, wood, plastics, and aluminium combined.

<span class="mw-page-title-main">Cement</span> Hydraulic binder used in the composition of mortar and concrete

A cement is a binder, a chemical substance used for construction that sets, hardens, and adheres to other materials to bind them together. Cement is seldom used on its own, but rather to bind sand and gravel (aggregate) together. Cement mixed with fine aggregate produces mortar for masonry, or with sand and gravel, produces concrete. Concrete is the most widely used material in existence and is behind only water as the planet's most-consumed resource.

<span class="mw-page-title-main">Fresco</span> Mural painting upon freshly laid lime plaster

Fresco is a technique of mural painting executed upon freshly laid ("wet") lime plaster. Water is used as the vehicle for the dry-powder pigment to merge with the plaster, and with the setting of the plaster, the painting becomes an integral part of the wall. The word fresco is derived from the Italian adjective fresco meaning "fresh", and may thus be contrasted with fresco-secco or secco mural painting techniques, which are applied to dried plaster, to supplement painting in fresco. The fresco technique has been employed since antiquity and is closely associated with Italian Renaissance painting.

<span class="mw-page-title-main">Calcium oxide</span> Chemical compound of calcium

Calcium oxide, commonly known as quicklime or burnt lime, is a widely used chemical compound. It is a white, caustic, alkaline, crystalline solid at room temperature. The broadly used term lime connotes calcium-containing inorganic compounds, in which carbonates, oxides, and hydroxides of calcium, silicon, magnesium, aluminium, and iron predominate. By contrast, quicklime specifically applies to the single compound calcium oxide. Calcium oxide that survives processing without reacting in building products, such as cement, is called free lime.

<span class="mw-page-title-main">Terrazzo</span> Cementitious composite material, usually used in flooring

Terrazzo is a composite material, poured in place or precast, which is used for floor and wall treatments. It consists of chips of marble, quartz, granite, glass, or other suitable material, poured with a cementitious binder, polymeric, or a combination of both. Metal strips often divide sections, or changes in color or material in a pattern. Additional chips may be sprinkled atop the mix before it sets. After it is cured it is ground and polished smooth or otherwise finished to produce a uniformly textured surface. "Terrazzo" is also often used to describe any pattern similar to the original terrazzo floors.

<span class="mw-page-title-main">Mortar (masonry)</span> Workable paste that hardens to bind building blocks

Mortar is a workable paste which hardens to bind building blocks such as stones, bricks, and concrete masonry units, to fill and seal the irregular gaps between them, spread the weight of them evenly, and sometimes to add decorative colours or patterns to masonry walls. In its broadest sense, mortar includes pitch, asphalt, and soft mud or clay, as those used between mud bricks, as well as cement mortar. The word "mortar" comes from Old French mortier, "builder's mortar, plaster; bowl for mixing." (13c.).

<span class="mw-page-title-main">Plaster</span> Broad range of building and sculpture materials

Plaster is a building material used for the protective or decorative coating of walls and ceilings and for moulding and casting decorative elements. In English, "plaster" usually means a material used for the interiors of buildings, while "render" commonly refers to external applications. The term stucco refers to plasterwork that is worked in some way to produce relief decoration, rather than flat surfaces.

<span class="mw-page-title-main">Building material</span> Material which is used for construction purposes

Building material is material used for construction. Many naturally occurring substances, such as clay, rocks, sand, wood, and even twigs and leaves, have been used to construct buildings and other structures, like bridges. Apart from naturally occurring materials, many man-made products are in use, some more and some less synthetic. The manufacturing of building materials is an established industry in many countries and the use of these materials is typically segmented into specific specialty trades, such as carpentry, insulation, plumbing, and roofing work. They provide the make-up of habitats and structures including homes.

<span class="mw-page-title-main">Stucco</span> Construction material made of aggregates, a binder, and water

Stucco or render is a construction material made of aggregates, a binder, and water. Stucco is applied wet and hardens to a very dense solid. It is used as a decorative coating for walls and ceilings, exterior walls, and as a sculptural and artistic material in architecture. Stucco can be applied on construction materials such as metal, expanded metal lath, concrete, cinder block, or clay brick and adobe for decorative and structural purposes.

<span class="mw-page-title-main">Lime (material)</span> Calcium oxides and/or hydroxides

Lime is an inorganic material composed primarily of calcium oxides and hydroxides. It is also the name for calcium oxide which occurs as a product of coal-seam fires and in altered limestone xenoliths in volcanic ejecta. The International Mineralogical Association recognizes lime as a mineral with the chemical formula of CaO. The word lime originates with its earliest use as building mortar and has the sense of sticking or adhering.

<span class="mw-page-title-main">Hydraulic lime</span> Substance used to make lime mortar

Hydraulic lime (HL) is a general term for calcium oxide, a variety of lime also called quicklime, that sets by hydration. This contrasts with calcium hydroxide, also called slaked lime or air lime that is used to make lime mortar, the other common type of lime mortar, which sets by carbonation (re-absorbing carbon dioxide (CO2) from the air). Hydraulic lime provides a faster initial set and higher compressive strength than air lime, and hydraulic lime will set in more extreme conditions, including under water.

<span class="mw-page-title-main">Tadelakt</span> Moroccan waterproof plaster

Tadelakt is a waterproof plaster surface used in Moroccan architecture to make baths, sinks, water vessels, interior and exterior walls, ceilings, roofs, and floors. It is made from lime plaster, which is rammed, polished, and treated with soap to make it waterproof and water-repellent. Tadelakt is labour-intensive to install, but durable. Since it is applied as a paste, tadelakt has a soft, undulating character, it can form curves, and it is seamless. Pigment can be added to give it any colour, but deep red is traditional. It may have a shiny or matte finish.

<span class="mw-page-title-main">Plasterwork</span> Construction or ornamentation done in plaster or a similar material

Plasterwork is construction or ornamentation done with plaster, such as a layer of plaster on an interior or exterior wall structure, or plaster decorative moldings on ceilings or walls. This is also sometimes called pargeting. The process of creating plasterwork, called plastering or rendering, has been used in building construction for centuries. For the art history of three-dimensional plaster, see stucco.

<span class="mw-page-title-main">Plasterer</span> Occupation of creating plasterwork

A plasterer is a tradesman or tradesperson who works with plaster, such as forming a layer of plaster on an interior wall or plaster decorative moldings on ceilings or walls. The process of creating plasterwork, called plastering, has been used in building construction for centuries. A plasterer is someone who does a full 4 or 2 years apprenticeship to be fully qualified.

<span class="mw-page-title-main">Lime mortar</span> Building material

Lime mortar or torching is a masonry mortar composed of lime and an aggregate such as sand, mixed with water. It is one of the oldest known types of mortar, used in ancient Rome and Greece, when it largely replaced the clay and gypsum mortars common to ancient Egyptian construction.

<span class="mw-page-title-main">Pozzolan</span> Siliceous volcanic ashes commonly used as supplementary cementitious material

Pozzolans are a broad class of siliceous and aluminous materials which, in themselves, possess little or no cementitious value but which will, in finely divided form and in the presence of water, react chemically with calcium hydroxide (Ca(OH)2) at ordinary temperature to form compounds possessing cementitious properties. The quantification of the capacity of a pozzolan to react with calcium hydroxide and water is given by measuring its pozzolanic activity. Pozzolana are naturally occurring pozzolans of volcanic origin.

<span class="mw-page-title-main">Marmorino</span>

Marmorino Veneziano is a type of plaster or stucco. It is based on calcium oxide and used for interior and exterior wall decorations. Marmorino plaster can be finished via multiple techniques for a variety of matte, satin, and glossy final effects. It was used as far back as Roman times, but was made popular once more during the Renaissance 500 years ago in Venice.

Polished plaster is a term for the finish of some plasters and for the description of new and updated forms of traditional Italian plaster finishes. The term covers a whole range of decorative plaster finishes, from the very highly polished Venetian plaster and Marmorino to the rugged look of textured polished plasters. Polished plaster itself tends to consist of slaked lime, marble dust, and/or marble chips, which give each plaster its distinctive look. A lime-based polished plaster may contain over 40% of marble powder.

<span class="mw-page-title-main">Roman concrete</span> Building material used in ancient Rome

Roman concrete, also called opus caementicium, was used in construction in ancient Rome. Like its modern equivalent, Roman concrete was based on a hydraulic-setting cement added to an aggregate.

<i>Qadad</i> Old technique used in plastering walls and cisterns

Qadad or qudad is a waterproof plaster surface, made of a lime plaster treated with slaked lime and oils and fats. The technique is over a thousand years old, with the remains of this early plaster still seen on the standing sluices of the ancient Marib Dam.

References

  1. Eliyahu-Behar, A.; Yahalom-Mack, N.; Ben-Shlomo, D. (2017). "Excavation and Analysis of an Early Iron Age Lime Kiln", Israel Exploration Journal 67, p. 29
  2. 1 2 Rahimzadeh, Chiya Y.; Mohammed, Ahmed Salih; Barzinjy, Azeez A. (3 October 2022). "Microstructure characterizations, thermal analysis, and compression stress–strain behavior of lime-based plaster". Construction and Building Materials. 350: 128921. doi:10.1016/j.conbuildmat.2022.128921. ISSN   0950-0618. S2CID   251820129.
  3. Qafih, Y. (1982). Halichot Teman (Jewish Life in Sanà) (in Hebrew). Jerusalem: Ben-Zvi Institute. p. 248. ISBN   965-17-0137-4. OCLC   863513860.
  4. Elert, Kerstin; García Sánchez, Rosa Maria; Benavides-Reyes, Cristina; Linares Ordóñez, Fátima (30 November 2019). "Influence of animal glue on mineralogy, strength and weathering resistance of lime plasters". Construction and Building Materials. 226: 625–635. doi:10.1016/j.conbuildmat.2019.07.261. ISSN   0950-0618. S2CID   201295868.
  5. Hagsten, Ellen. General Guidelines for Working with Lime Mortar and Limewash, Traditional & Sustainable Building, March 2007
  6. Leslie, Thomas (2020). ""Dry and Ready in Half the Time:" Gypsum Wallboard's Uneasy History". doi:10.13140/RG.2.2.30855.83365.{{cite journal}}: Cite journal requires |journal= (help)
  7. Nicholas, Stephen J.; Nicholas, Jacqueline M. (1992). "Male Literacy, "Deskilling," and the Industrial Revolution". The Journal of Interdisciplinary History. 23 (1): 1–18. doi:10.2307/205479. ISSN   0022-1953. JSTOR   205479.
  8. Salavessa, Eunice; Jalali, Said; Sousa, Luís M. O.; Fernandes, Lisete; Duarte, Ana Maria (1 November 2013). "Historical plasterwork techniques inspire new formulations". Construction and Building Materials. 48: 858–867. doi: 10.1016/j.conbuildmat.2013.07.064 . ISSN   0950-0618.
  9. "Traces of Ancient Rome in the Modern World". education.nationalgeographic.org. Retrieved 7 July 2023.
  10. O'neil, Shannon Leigh. "Limestone in Ancient Greek Architecture | Synonym". classroom.synonym.com. Retrieved 7 July 2023.
  11. "A brief description of the main Roman masonry techniques. 1st. Part". aeternitasnumismatic (in Spanish). 23 November 2017. Retrieved 7 July 2023.
  12. "Riddle solved: Why was Roman concrete so durable?". MIT News | Massachusetts Institute of Technology. 6 January 2023. Retrieved 7 July 2023.
  13. "Vitruvius | Roman architect | Britannica". www.britannica.com. Retrieved 7 July 2023.
  14. "Evolution of Construction in Rome's Historic Districts – Engineering Rome" . Retrieved 7 July 2023.
  15. "Carlo Scarpa". Architectuul. Retrieved 7 July 2023.
  16. "Lime plaster statues". britishmuseum.org. British Museum. Retrieved 21 November 2013.
  17. J.N. Tubb, Canaanites, London, The British Museum Press, 1998
  18. Garfinkel, Yosef. "Y. Garfinkel. 1987. Burnt Lime Products and Social Implications in the Pre-Pottery Neolithic B Villages of the Near East. Paléorient 13/1: 68–75".
  19. Monumental Figures utexas.edu July 2018
  20. Cowper, Ad. Lime and Lime Mortars, first published for the Building Research Station by HM Stationery Office, London, 1927
  21. Evans, Susan Toby (2008). Ancient Mexico & Central America: Archaeology and Culture History. Thames & Hudson. ISBN   978-0-500-28714-9.
  22. organiksoft.com, OrganikSoft. "Historic Features - Old Mission San Luis Rey". sanluisrey.org.

Further reading

  1. "Learning Center". Lancaster Lime Works. Retrieved 12 January 2023.