Springfield Model 1816 | |
---|---|
Type | Musket |
Place of origin | United States |
Service history | |
In service | 1816–1865 |
Used by | United States Confederate States |
Wars | American Indian Wars Mexican–American War American Civil War |
Production history | |
Designer | Eli Whitney |
Designed | 1816 |
Manufacturer | Springfield Armory Harpers Ferry Armory Various private contractors |
Produced | 1816–1844 Type I: 1816–1822 [1] Type II: 1822–1835 [1] Type III: 1835–1844 [1] |
No. built | c. 700,000 |
Variants | Percussion, rifled musket (conversions) |
Specifications | |
Mass | 10 lb (4.5 kg) |
Length | 58.0 in (1,470 mm) |
Barrel length | 42.0 in (1,070 mm) |
Cartridge | Paper cartridge, buck and ball/musket ball undersized (.65/16.510 mm) to reduce the effects of powder fouling |
Caliber | .69 in (17.526 mm) |
Action | Flintlock/percussion lock (conversion) |
Rate of fire | User dependent; usually 2 to 3 rounds per minute |
Muzzle velocity | 1,000 ft/s (300 m/s) to 1,200 ft/s (370 m/s) |
Effective firing range | 100 to 200 yards, in reality 50 to 75 yards |
Maximum firing range | 300 yd (275 m) [2] |
Feed system | Muzzle-loaded |
Sights | A front sight cast into the upper barrel band, rear sight (percussion/rifled conversion) |
The Springfield Model 1816 was a .69 caliber flintlock musket manufactured in the United States during the early 19th century.
The War of 1812 had revealed many weaknesses in American muskets. The Springfield Model 1812 was created in an attempt to improve both the design and manufacture of the musket. The Model 1816 made further improvements, and replaced the Model 1812. The Model 1812 had borrowed heavily from the design of the French Charleville Model 1777, and this design was retained for the Model 1816. The Model 1816 had a 42-inch (107 cm) long .69 caliber smoothbore barrel, similar to the Model 1812, but had a longer lock plate, a shorter trigger guard, and a longer bayonet than the Model 1812. The Model 1816 also had a more straight lined stock. The overall length of the weapon was 58 inches (147 cm). [3]
The Model 1816 musket was originally manufactured at the Springfield and Harpers Ferry armories along with independent contractors between 1816 and 1844. Around 700,000 were made, more than any other flintlock in U.S. history. [4]
The Model 1816 was originally manufactured as a flintlock musket. Like many flintlock muskets, many of these were later converted to percussion cap, as the percussion cap system was much more reliable and weather resistant. Some also had their barrels rifled as well.
This model of Springfield musket was used by Texans during the Texas Revolution and by the U.S. Army and militia during the Mexican–American War. During this conflict, the flintlock version of the Model 1816 was preferred by U.S. regular forces, due to percussion cap supply concerns. [5]
It was also used during the early years of the American Civil War until around 1862. The large majority of Model 1816 muskets had been converted to percussion firing by 1860. Muskets made prior to 1821 were considered too outdated to be serviceable weapons and were not converted. Most of them were in Southern arsenals and a large number of Confederate soldiers for the first year of the Civil War had the misfortune of carrying flintlock muskets, some of which dated back to the War of 1812.
Many improvements to the Model 1816 were made, producing the Springfield Model 1822, Springfield Model 1835, Springfield Model 1840, and Springfield Model 1842. U.S. Ordnance Department referred to these as different models, but in other U.S. government documents they are referred to as a continuation of the Model 1816 with the first model designated as the Type I, the Model 1822 as the Type II, and the Model 1835 as the Type III. [3] Modern histories are similarly inconsistent in the nomenclature of these weapons.
The percussion cap, percussion primer, or caplock, introduced in the early 1820s, is a type of single-use percussion ignition device for muzzle loader firearm locks enabling them to fire reliably in any weather condition. Its invention gave rise to the caplock mechanism or percussion lock system which used percussion caps struck by the hammer to set off the gunpowder charge in rifles and cap and ball firearms. Any firearm using a caplock mechanism is a percussion gun. Any long gun with a cap-lock mechanism and rifled barrel is a percussion rifle. Cap and ball describes cap-lock firearms discharging a single bore-diameter spherical bullet with each shot.
Flintlock is a general term for any firearm that uses a flint-striking ignition mechanism, the first of which appeared in Western Europe in the early 16th century. The term may also apply to a particular form of the mechanism itself, also known as the true flintlock, that was introduced in the early 17th century, and gradually replaced earlier firearm-ignition technologies, such as the matchlock, the wheellock, and the earlier flintlock mechanisms such as the snaplock and snaphaunce.
The Charleville musket was a .69 caliber standard French infantry musket used in the 18th and 19th centuries. It was made in 1717 and was last produced during the 1840s. However, it still saw limited use in conflicts through the mid-19th century.
The Springfield Model 1861 was a Minié-type rifled musket used by the United States Army during the American Civil War. Commonly referred to as the "Springfield". It was the most widely used Union Army shoulder weapon during the Civil War, favored for its range, accuracy, and reliability.
The Springfield Model 1863 was a .58 caliber rifled musket manufactured by the Springfield Armory and independent contractors between 1863 and 1865.
A rifled musket, rifle musket, or rifle-musket is a type of firearm made in the mid-19th century. Originally the term referred only to muskets that had been produced as a smoothbore weapon and later had their barrels replaced with rifled barrels. The term later included rifles that directly replaced, and were of the same design overall as, a particular model of smoothbore musket.
The M1819 Hall rifle was a single-shot breech-loading rifle designed by John Hancock Hall, patented on May 21, 1811, and adopted by the U.S. Army in 1819. It was preceded by the Harpers Ferry M1803. It used a pivoting chamber breech design and was made with either flintlock or percussion cap ignition systems. The years of production were from the 1820s to the 1840s at the Harpers Ferry Arsenal. This was the first breech-loading rifle to be adopted in large numbers by any nation's army, but not the first breech-loading military rifle – the Ferguson rifle was used briefly by the British Army in the American Revolutionary War. The Hall rifle remained overshadowed by common muskets and muzzleloading rifles which were still prevalent until the Civil War. The early flintlocks were mostly converted to percussion ignition.
The Springfield Model 1840 was a flintlock musket manufactured by the United States during the mid-19th century. The .69 caliber musket had a 42-inch (107 cm) barrel, an overall length of 58 inches (147 cm), and a weight of 9.8 pounds (4.4 kg). More than 30,000 were produced by the Springfield and Harpers Ferry armories and two independent contractors between 1840 and 1846.
The Springfield Model 1822 was a .69 caliber flintlock musket manufactured by the United States in the early 19th century.
The Springfield Model 1812 Musket is a .69 caliber, flintlock musket manufactured by the Springfield Armory.
The Springfield Model 1795 was a .69 caliber flintlock musket manufactured in the late 18th and early 19th centuries in the United States.
The Springfield Model 1868 was one of the rifles which used the trapdoor breechblock design developed by Erskine S. Allin.
The M1841 Mississippi rifle is a muzzle-loading percussion rifle used in the Mexican–American War and the American Civil War.
The Harper's Ferry Model 1805 U.S. martial flintlock pistol manufactured at the Harpers Ferry Armory in Virginia was the first pistol manufactured by an American national armory. It was the standard handgun of the U.S. Dragoons during the War of 1812.
During the American Civil War, an assortment of small arms found their way onto the battlefield. Though the muzzleloader percussion cap rifled musket was the most numerous weapon, being standard issue for the Union and Confederate armies, many other firearms, ranging from the single-shot breech-loading Sharps and Burnside rifles to the Spencer and the Henry rifles - two of the world's first repeating rifles - were issued by the hundreds of thousands, mostly by the Union. The Civil War brought many advances in firearms technology, most notably the widespread use of rifled barrels.
The Springfield Model 1835 was a .69 caliber flintlock musket manufactured in the United States during the early 19th century.
A pistoleer is a mounted soldier trained to use a pistol, or more generally anyone armed with such a weapon. It is derived from pistolier, a French word for an expert marksman.
Springfield musket may refer to any one of several types of small arms produced by the Springfield Armory in Springfield, Massachusetts, for the United States armed forces. In modern times, these muskets are commonly referred to by their date of design followed by the name Springfield. However, U.S. Ordnance Department documentation at the time did not use "Springfield" in the name.
The US Model 1842 Musket was a .69 caliber musket manufactured and used in the United States during the 19th century. It is a continuation of the Model 1816 line of muskets but is generally referred to as its own model number rather than just a variant of the Model 1816.
The Springfield Model 1855 was a rifled musket widely used in the American Civil War. It exploited the advantages of the new conical Minié ball, which could be deadly at over 1,000 yards (910 m). It was a standard infantry weapon for Union and Confederates alike, until the Springfield Model 1861 supplanted it, obviating the use of the insufficiently weather resistant Maynard tape primer.
{{cite book}}
: CS1 maint: location (link)