NER Class W

Last updated

NER Class W
Type and origin
Power typeSteam
Designer Wilson Worsdell
Builder Gateshead Works
Build date1907–08
Total produced10
Specifications
Configuration:
   Whyte 4-6-0T
   UIC 2′C n2t
Gauge 4 ft 8+12 in (1,435 mm)
Wheelbase 26 ft 3 in (8.001 m)
Length40 ft 8+12 in (12.408 m)
Adhesive weight 52 long tons (53 t; 58 short tons)
Loco weight69.85 long tons (70.97 t; 78.23 short tons)
Fuel typeCoal
Fuel capacity2.25 long tons (2.29 t; 2.52 short tons)
Water cap.1,500 imp gal (6,800 L; 1,800 US gal)
Firebox:
  Firegrate area
23 sq ft (2.1 m2)
Boiler pressure170 lbf/in2 (1.17 MPa)
Heating surface1,312 sq ft (121.9 m2)
  Tubes1,182 sq ft (109.8 m2)
  Firebox130 sq ft (12 m2)
Cylinders Two, inside
Cylinder size 19 in × 26 in (483 mm × 660 mm)
Valve gear Stephenson
Career
Operators North Eastern Railway
Numbers686–695
DispositionAll rebuilt as Class W1 (1914–1917)
[1]

The NER Class W was a class of ten 4-6-0T locomotives built by the North Eastern Railway at their Gateshead Works between 1907 and 1908. They were all rebuilt as Class W1 4-6-2T locomotives between 1914 and 1917.

The ten locomotives were built in one batch, and were numbered 686 to 695. They were designed for the Scarborough to Whitby line, on which the Class O 0-4-4T locomotives then in use were having difficulty with the traffic, especially the three-mile (4.8 km) section of 1 in 40 (2.5%). [2] However, the low fuel and water capacity was a barrier to operational efficiency, and so between September 1914 and January 1917 the whole class was rebuilt as 4–6–2T locomotives and reclassified W1.

Only one batch was built as the design was soon superseded by the Class D 4-4-4T.

Table of locomotives
NER No.Works No.Date builtDate rebuilt
68684December 1907May 1915
68785December 1907January 1917
68886December 1907September 1914
68987January 1908May 1915
69088February 1908August 1916
69189March 1908June 1915
69290March 1908May 1916
69391March 1908February 1916
69492April 1908May 1915
69593April 1908July 1915

Related Research Articles

<span class="mw-page-title-main">4-6-2</span> Locomotive wheel arrangement

Under the Whyte notation for the classification of steam locomotives, 4-6-2 represents the wheel arrangement of four leading wheels on two axles, six powered and coupled driving wheels on three axles and two trailing wheels on one axle. The 4-6-2 locomotive became almost globally known as a Pacific type after a New Zealand locomotive that was shipped across the Pacific Ocean.

<span class="mw-page-title-main">4-6-4</span> Locomotive wheel arrangement

Under the Whyte notation for the classification of locomotives, 4-6-4 represents the wheel arrangement of four leading wheels, six powered and coupled driving wheels and four trailing wheels. In France where the type was first used, it is known as the Baltic while it became known as the Hudson in most of North America.

The London, Midland and Scottish Railway had the largest stock of steam locomotives of any of the 'Big Four' Grouping, i.e. pre-Nationalisation railway companies in the UK. Despite early troubles arising from factions within the new company, the LMS went on to build some very successful designs; many lasted until the end of steam traction on British Railways in 1968. For an explanation of numbering and classification, see British Rail locomotive and multiple unit numbering and classification.

<span class="mw-page-title-main">4-6-0</span> Railway steam locomotive wheel arrangement

A 4-6-0 steam locomotive, under the Whyte notation for the classification of steam locomotives by wheel arrangement, has four leading wheels on two axles in a leading bogie and six powered and coupled driving wheels on three axles with the absence of trailing wheels.

The Southern Railway took a key role in expanding the 660 V DC third rail electrified network begun by the London & South Western Railway. As a result of this, and its smaller operating area, its steam locomotive stock was the smallest of the 'Big Four' companies.

<span class="mw-page-title-main">2-6-4</span> Locomotive wheel arrangement

Under the Whyte notation for the classification of steam locomotives, a 2-6-4 locomotive has two leading wheels, six coupled driving wheels and four trailing wheels.

<span class="mw-page-title-main">GWR 4300 Class</span> Class of 342 two-cylinder 2-6-0 locomotives

The Great Western Railway (GWR) 4300 Class is a class of 2-6-0 (mogul) steam locomotives, designed by G.J. Churchward for mixed traffic duties. 342 were built from 1911–1932.

<span class="mw-page-title-main">Locomotives of India</span> A list of locomotives made and run in India

The Indian Railways primarily operates a fleet of electric and diesel locomotives, along with several compressed natural gas (CNG) locomotives. Steam locomotives are operated on a few World Heritage Sites and also run occasionally as heritage trains. A locomotive is also known as a loco or more popularly as an engine. The country's first steam locomotive ran on the Red Hill Railway from Red Hills to the Chintadripet bridge in Madras in 1837.

<span class="mw-page-title-main">GER Class S69</span>

The Great Eastern Railway (GER) Class S69, also known as 1500 Class, and later classified B12 by the London and North Eastern Railway (LNER) is a class of 4-6-0 steam locomotive designed to haul express passenger trains from London Liverpool Street station along the Great Eastern Main Line. Originally they were designed by S. D. Holden, but were much rebuilt, resulting in several subclasses.

<span class="mw-page-title-main">GNR Class J23</span>

The Great Northern Railway Class J23 was a class of 0-6-0T steam locomotive. They had long side tanks that came to the front of the smokebox, which sloped forwards to improve visibility and had a recess cut in to aid maintenance. Forty were built by the Great Northern Railway (GNR) between 1913 and 1922, with a further 62 being added by the London and North Eastern Railway (LNER) between 1924 and 1939. They were given the nickname "Submarines" due to their long tanks.

<span class="mw-page-title-main">GCR Class 9N</span>

The Great Central Railway Class 9N, classified A5 by the LNER, was a class of 4-6-2 tank locomotives designed by John G. Robinson for suburban passenger services. They were fitted with superheaters, piston valves and Stephenson valve gear.

<span class="mw-page-title-main">NER Class D</span>

The North Eastern Railway Class D was a class of 4-4-4T three-cylinder side tank steam locomotive designed by Vincent Raven in 1913. They were used for rural passenger services. Forty five were built in total; a first batch of twenty, then a further twenty five after the War.

<span class="mw-page-title-main">S. D. Holden</span> British engineer (1870–1918)

Stephen Dewar Holden was a British engineer, the son of the engineer James Holden and succeeded his father as locomotive superintendent of the Great Eastern Railway in 1908, a post he held until his retirement in 1912.

<span class="mw-page-title-main">LB&SCR E1 class</span>

The London, Brighton and South Coast Railway E1 Class were 0-6-0T steam locomotives designed by William Stroudley in 1874 for short-distance goods and piloting duties. They were originally classified E, and generally known as "E-tanks"; They were reclassified E1 in the time of D. E. Marsh.

<span class="mw-page-title-main">NER Class Y</span>

The North Eastern Railway (NER) Class Y 4-6-2T tank locomotives were designed whilst Wilson Worsdell was Chief Mechanical Engineer, but none were built until 1910 by which time Vincent Raven had taken over.

<span class="mw-page-title-main">Taff Vale Railway A class</span> Class of 58 British 0-6-2T locomotives

The Taff Vale Railway A class was a class of 0-6-2T steam tank locomotives designed by J. Cameron for mixed traffic work and introduced to the Taff Vale Railway (TVR) in 1914. The A class was an enlarged version of the TVR O4 class designed by Tom Hurry Riches in 1907. The A class was the last new class of locomotive to be introduced on the TVR, which had introduced its first 0-6-2Ts in 1885 ; and, with a total of 58 built, was numerically the largest class of tank locomotive on the TVR.

The NER Class W1 was a 4-6-2T steam locomotive of the North Eastern Railway. The class was introduced in 1914 as a rebuild of Wilson Worsdell's NER Class W 4-6-0T. At the 1923 Grouping, they all passed to the London and North Eastern Railway, who placed them in their Class A6.

The SER 235 class was a class of 0-4-4T steam locomotives on the South Eastern Railway. Introduced in 1866, they were the first locomotives of this wheel arrangement to be built for an English railway.

<span class="mw-page-title-main">GCR Class 1B</span>

The GCR Class 1B was a class of 2-6-4T (tank) locomotives on the Great Central Railway. They were notable as the first locomotives of the 2-6-4T wheel arrangement to be used by a British standard-gauge railway; there had been two narrow-gauge examples on the Leek & Manifold Valley Light Railway since 1904.

The locomotives of the Highland Railway were used by the Highland Railway to operate its lines in the north of Scotland. The Highland Railway locomotive works was at Lochgorm, Inverness. The works had been built about 1855 by the Inverness and Nairn Railway. The locomotive classes are listed under the names of the railway's Locomotive Superintendents.

References

  1. Fry 1964, pp. 11–13.
  2. Fry 1964, pp. 11–12.