North Avenue Bridge

Last updated
North Avenue Bridge
North Avenue Bridge over the North Branch of the Chicago River.jpg
North Avenue Bridge from Goose Island
Coordinates 41°54′39″N87°39′25″W / 41.9108°N 87.6569°W / 41.9108; -87.6569
Carries4 lanes of North Avenue (Illinois 64.svg IL 64), 2 sidewalks
CrossesNorth Branch of the Chicago River
Locale Chicago, Illinois
Official nameNorth Avenue Bridge
Characteristics
DesignHybrid suspension/cable-stayed
Total length420 ft (128 m) [1]
Width78.5 ft (23.9 m) [1]
Height50 ft (15 m) [1]
Longest span252 ft (77 m) [1]
Clearance below 18 ft (5 m) [1]
History
Construction startMid-June, 2006
Construction endMay 23, 2008 [2]
OpenedMay 23, 2008 [2]
Statistics
Daily traffic 40,000
Location
North Avenue Bridge

The North Avenue Bridge can refer to one of three bridges that has carried North Avenue (Illinois Route 64) over the North Branch of the Chicago River on the north side of Chicago, Illinois. A center-pier swing bridge built in 1877 was replaced in 1907 by a bascule bridge, allowing river traffic more room for maneuvering in and out of the North Canal, just north of Goose Island.

Contents

Due to deteriorating conditions and inadequate capacity, the bascule bridge was demolished in 2006 to make room for a hybrid suspension/cable-stayed bridge. The suspension/cable-stayed bridge fully opened on May 23, 2008.

History

As Chicago grew into a center of industry and commerce in the late 19th century, numerous fixed-span crossings were replaced by center-pier swing bridges, the most common type of bridge that allowed pedestrians and wagons to cross the Chicago River while also periodically allowing ship traffic below. In 1877, one of these bridges was constructed just north of Goose Island. [3]

Development of the bascule bridge

Western portal of the North Avenue Bridge constructed in 1907 Western Portal, North Avenue Bridge, Chicago, Illinois.jpg
Western portal of the North Avenue Bridge constructed in 1907

The 1877 bridge and its counterparts, while the most common bridge of the mid-19th century, were criticized by both the shipping and real estate industries of Chicago. As the 19th century came to a close, shipping vessels had grown larger, and the swing bridges' center piers had become navigational hazards. In addition, each swing span required a large clearance around the bridge, preventing the development of docking facilities near the bridge. As open land along the Chicago River grew scarce, real estate and shipping companies grew increasingly critical of the swing spans.

No progress was made on the issue until 1890, when the United States Congress gave the United States War Department the authorization to build new bridges over waterways, and to force changes to existing bridges that posed a hazard to navigation. In 1892, the directive was enforced in Chicago when a just-completed bridge at Canal Avenue was ordered removed by the U.S. Army Corps of Engineers. That year, the city's engineers began to study suitable alternatives to the hazardous swing-span bridge.

The search generated disagreement between the Scherzer Rolling Lift Company of Chicago and Chicago Department of Public Works City Engineer John E. Ericson. Although the rolling lift bridge (a type of bascule bridge) was mechanically the most simple alternative, engineers soon discovered that the span applied its load in a rolling motion on its foundation, crumbling poorly built foundations. Ericson directed his staff to investigate other bridges in the U.S. and Europe, eventually finding that the Tower Bridge (1894) would be an appropriate starting point.

With a model bridge that was patent-free, had a fixed center of gravity and simple mechanical motion, in 1900 Ericson prompted the Chicago City Council to allocate funding to replace five deteriorating swing-span bridges. The first five bridges were built at Clybourn Place (later Cortland Avenue) in 1902, Division Street over both the North Branch Canal (1903) and the Chicago River (1904), 95th Street over the Calumet River (1903) and at Western Avenue over the North Branch Canal (1904). During the same period of time, the Scherzer Company built seven of their rolling lift bridges over the Chicago Sanitary and Ship Canal, which was widened to accommodate larger flows from the recently reversed Chicago River. These bridges, built under the authority of the Chicago Sanitary District, only needed to be approved by the Corps of Engineers, not the Department of Public Works.

By 1904, the city had obtained permission to issue bonds to replace the rest of the swing bridges on the Chicago River. Ericson sent the Scherzer Company and the Sanitary District specifications for the bridge in 1905. A design by John W. Page, the inventor of a bascule bridge over the Sanitary and Ship Canal, was rejected in March 1905 due to noncompliance to specifications. The Scherzer Company waited until the bidding deadline to submit two separate designs; both of these were also rejected due to noncompliance. Two contracts were bid out for the trunnion style bascule bridge that Ericson had pioneered; one contract for $81,369 (1905) went to the Jackson and Corbett Company for the substructure, and one for $111,983 (1905) went to the Roemheld and Gallery Company for superstructure work.

After the decision, Scherzer brought its argument with Ericson into court, arguing that the Department of Public Works had "maliciously, fraudulently and unlawfully" prohibited Scherzer from bidding their bridge design, which they claimed was both superior in quality and less expensive. A settlement was reached in August 1905, and construction for the new North Avenue Bridge began in early 1906.

Ericson was removed from the Public Works' bridge division and control over bridge design was passed to a separate administrative entity headed by Thomas G. Pihlfeldt. However, under Pihlfeldt's guidance the city continued to express preference for the trunnion bascule design. [3]

1907 bridge description

An illustration of a Pratt truss, the most common type of bridge built in the United States during the early 20th century. The 1907 North Avenue Bridge was a modified Pratt truss. Pratt truss.svg
An illustration of a Pratt truss, the most common type of bridge built in the United States during the early 20th century. The 1907 North Avenue Bridge was a modified Pratt truss.

The bridge measured about 260 feet (79 m) from one abutment to the other. The bridge took the general form of a Pratt truss; however, where most Pratt trusses would incline downwards at the shoreline, the tail ends of the North Avenue Bridge truss curved upwards, tapering towards the center of the span. Where the tail ends were tallest, deep lateral braces provided support for the bridge.

1907 North Avenue Bridge in 1999, looking north from Goose Island 1907 North Avenue Bridge, looking north, Chicago, Illinois.jpg
1907 North Avenue Bridge in 1999, looking north from Goose Island

The deck of the bridge was 60 feet (18 m) wide at the approaches. Upon construction, the roadway for the approaches consisted of wood blocks atop a steel-supported concrete slab. Approach sidewalks, made of concrete, had railings made of steel mesh that overlooked the river. On the movable leaves, a 42-foot (13 m) wide wooden deck was centered between two 9-foot (3 m) metal brackets that held plank sidewalks. The roadway itself was separated by the center truss. Originally, streetcar tracks ran on both sides of the bridge. [3]

Decline of the North Branch shipping district

After new manufacturing facilities opened on the Calumet River in the southern portion of Chicago, shipping traffic on the Chicago River fell dramatically. By the mid-1920s, the Department of Public Works had floated a proposal to replace the moving bridges with fixed spans through a ten-year period from 1925–1935, citing high maintenance costs. The proposal was not acted upon, partially due to opposition by the Army Corps of Engineers; however, except for a brief resurgence in traffic during World War II, shipping volume remained low. [3]

The historical bridge was last raised in 1972. By the 1990s, the Corps of Engineers agreed to city plans to convert the Chicago River's lift bridges to fixed spans. [3] As the surrounding area transformed from primarily industrial to residential and commercial in nature, traffic volumes on the aging bridge increasing, causing bottlenecks. [4]

As required by National Historic Preservation Act Section 106 regulations, the city offered the structure to any interested parties for relocation and preservation elsewhere. Because of the complexity of the outdated lifting mechanism, no cities offered to take the bridge. [5]

2007-2008 bridge replacement

Due to age and the high cost of maintenance, a replacement fixed-span bridge was built through 2007–2008. The new bridge is a fixed-span, hybrid suspension/cable-stayed bridge of the same height but nearly twice as long in length. The original bridge was two lanes wide; the new bridge has four lanes plus sidewalks, helping to reduce congestion caused by the 40,000 cars/day that travel on the bridge. [4]

James McHugh Construction Company served as the general contractor for the new bridge. Designs for the new North Avenue Bridge were constrained by several factors. An active railroad line runs along the eastern bank of the river, requiring a level-crossing or overpass. The banks of the Chicago River were to be kept open and utilized for further development. The United States Coast Guard required the bridge to have a vertical clearance of 18 feet (5 m). Finally, the new crossing, situated at the northern tip of Goose Island and having a clear view to the Chicago skyline, was required to be aesthetically pleasing.

Due to rising costs of steel, the construction of a new bascule bridge was ruled out. The length of the crossing proved to be too short for a pure suspension bridge, while a pure cable-stayed bridge would require a larger tower than preferred for the site. As a result, engineers turned to the concept of a hybrid suspension/cable-stayed bridge.

Prior to work on the new bridge, work crews constructed and opened a temporary bridge just to the north of the new bridge. The temporary bridge allowed for the relocation of utilities, construction of an improved river wall and uninterrupted substructure construction for the new bridge. The center span was constructed on three barges in the Chicago River, because of Coast Guard regulations that required the channel to be open at all times. After the center span was constructed, it was towed to the bridge, where 16 jacks lifted the span into place.

The new bridge was completed in 22 months, and cost US$25,000,000 to build. [2] The bridge is anchored by four pairs of pylons, with each pylon weighing 95,000 pounds (43,091 kg). The pylons rest on 10 smaller micropiles that extend 90 feet (27 m) into bedrock. From the pylons, a total of 24 cable-stays support the approach spans, as well as the ends of the center span. A suspension cable, running from anchorages at the feet of the bridge to the tops of the pylons, supports the middle portion of the center span. [1]

The deck of the bridge is post-tensioned to allow horizontal forces of the bridge to be transferred to anchor blocks at the ends of the span. It was constructed with 10 inches (25 cm) of high-performance concrete, and with a 2-inch (5 cm) latex overlay. [1] The total thickness of the deck is only 4 feet (1 m). [6]

North Avenue Bridge from Goose Island, Chicago, Illinois.jpg
North Avenue Bridge from Goose Island in Chicago, Illinois.

See also

Related Research Articles

<span class="mw-page-title-main">Cable-stayed bridge</span> Type of bridge with cables directly from towers to deck

A cable-stayed bridge has one or more towers, from which cables support the bridge deck. A distinctive feature are the cables or stays, which run directly from the tower to the deck, normally forming a fan-like pattern or a series of parallel lines. This is in contrast to the modern suspension bridge, where the cables supporting the deck are suspended vertically from the main cable, anchored at both ends of the bridge and running between the towers. The cable-stayed bridge is optimal for spans longer than cantilever bridges and shorter than suspension bridges. This is the range within which cantilever bridges would rapidly grow heavier, and suspension bridge cabling would be more costly.

<span class="mw-page-title-main">Swing bridge</span> Bridge that rotates horizontally around a vertical axis

A swing bridge is a movable bridge that can be rotated horizontally around a vertical axis. It has as its primary structural support a vertical locating pin and support ring, usually at or near to its center of gravity, about which the swing span can then pivot horizontally as shown in the animated illustration to the right.

<span class="mw-page-title-main">Bascule bridge</span> Moveable bridge with a counterweight which keeps the span(s) balanced during the upswing

A bascule bridge is a moveable bridge with a counterweight that continuously balances a span, or leaf, throughout its upward swing to provide clearance for boat traffic. It may be single- or double-leafed.

<span class="mw-page-title-main">BNSF Railway Bridge 5.1</span> Railroad bridge in Portland, Oregon

The BNSF Railway Bridge 5.1, also known as the St. Johns Railroad Bridge or the Willamette River Railroad Bridge, is a through truss railway bridge with a vertical lift that spans the Willamette River in Portland, Oregon, United States. Built by the Spokane, Portland and Seattle Railway (SP&S) and completed in 1908, it was originally a swing-span bridge, and its swing-span section was the longest in the world at the time. However, 81 years later the main span was converted from a swing-type to a vertical-lift type, in order to widen the navigation channel. The lift span is one of the highest and longest in the world. The bridge consists of five sections, with the two sections closest to the bank on each side fixed.

<span class="mw-page-title-main">Goose Island (Chicago)</span> Artificial island in Chicago, Illinois, US

Goose Island is a 160 acre artificial island in Chicago, Illinois, formed by the North Branch of the Chicago River on the west and the North Branch Canal on the east. It is about 1.5 miles (2.4 km) long and 0.5 miles (0.80 km) across at its widest point.

<span class="mw-page-title-main">Moveable bridge</span> Bridge that moves to allow passage, usually of watercraft

A moveable bridge, or movable bridge, is a bridge that moves to allow passage for boats or barges. In American English, the term is synonymous with drawbridge, and the latter is the common term, but drawbridge can be limited to the narrower, historical definition used in some other forms of English, in which drawbridge refers to only a specific type of moveable bridge often found in castles.

<span class="mw-page-title-main">Architecture of Portland, Oregon</span>

Portland architecture includes a number of notable buildings, a wide range of styles, and a few notable pioneering architects.

<span class="mw-page-title-main">Industrial Canal</span> Canal in Louisiana, United States of America

The Industrial Canal is a 5.5 mile (9 km) waterway in New Orleans, Louisiana, United States. The waterway's proper name, as used by the U.S. Army Corps of Engineers and on NOAA nautical charts, is Inner Harbor Navigation Canal (IHNC). The more common "Industrial Canal" name is used locally, both by commercial mariners and by landside residents.

<span class="mw-page-title-main">CRRNJ Newark Bay Bridge</span> Railroad bridge connecting Elizabethport and Bayonne

The Newark Bay Bridge of the Central Railroad of New Jersey (CNJ) was a railroad bridge in New Jersey that connected Elizabethport and Bayonne at the southern end of Newark Bay. Its third and final incarnation was a four-track vertical-lift design that opened in 1926, replacing a bascule bridge from 1904 which superseded the original swing bridge from 1887. The bridge served the main line of the CNJ, carrying daily interstate trains as well as commuter trains.

<span class="mw-page-title-main">Harlem River Lift Bridge</span> Bridge between Manhattan and the Bronx, New York

The Harlem River Lift Bridge is a vertical lift bridge carrying the Metro-North Railroad's Hudson Line, Harlem Line, and New Haven Line across the Harlem River between the boroughs of Manhattan and the Bronx in New York City. The average weekday ridership on the lines is 265,000.

<span class="mw-page-title-main">Erasmusbrug</span> Bridge in Rotterdam, The Netherlands

The Erasmusbrug is a combined cable-stayed and bascule bridge, construction began in 1986 and was completed in 1996. It crosses the Nieuwe Maas in the centre of Rotterdam, connecting the north and south parts of this city, second largest in the Netherlands. The bridge was named in 1992 after Desiderius Erasmus, a prominent Christian Renaissance humanist also known as Erasmus of Rotterdam. The Erasmus Bridge is Rotterdam's most important landmark and is even part of the city's official logo.

<span class="mw-page-title-main">St. Claude Avenue Bridge</span> Bridge in New Orleans, Louisiana, United States

The St. Claude Avenue Bridge is a bascule bridge with four vehicular lanes over the Industrial Canal in New Orleans, Louisiana. The bridge was designed by the Strauss Bascule Bridge Company of Chicago and built in 1919 by the Bethlehem Steel Bridge Corporation. It was originally a combination railroad and automobile bridge, with two pairs of railroad tracks in the center of the lift span and automobile lanes straddling it. The railroad is no longer there, its place on the bridge taken by additional vehicular lanes. One lane in each direction passes through the truss of the bridge and one lane passes alongside the truss. The bridge is integrated into the Industrial Canal Lock structure, on the river side of the lock chamber; it raises when marine traffic enters or exits the lock.

<span class="mw-page-title-main">Cortland Street Drawbridge</span> American bridge

The Cortland Street Drawbridge over the Chicago River is the original Chicago-style fixed-trunnion bascule bridge, designed by John Ericson and Edward Wilmann. When it opened in 1902, on Chicago's north side, it was the first such bridge built in the United States. The bridge was a major advance in American movable bridge engineering, and was the prototype for over 50 additional bridges in Chicago alone. The bridge was designated as an ASCE Civil Engineering Landmark in 1981, and a Chicago Landmark in 1991.

<span class="mw-page-title-main">Kinzie Street railroad bridge</span> Bridge in Chicago

The Chicago and North Western Railway's Kinzie Street railroad bridge is a single leaf bascule bridge across the north branch of the Chicago River in downtown Chicago, Illinois. At the time of its opening in 1908 it was the world's longest and heaviest bascule bridge. The previous bridges on the same site included a pedestrian span that was the first bridge across the Chicago River; a second bridge that served as Chicago's first railroad bridge; and a third bridge that was one of the first all-steel spans in the United States.

<span class="mw-page-title-main">Cherry Avenue Bridge</span> Bridge in Chicago, Illinois, U.S.

The Cherry Avenue Bridge is an asymmetric bob-tail swing bridge in Chicago, Illinois that carries the Chicago Terminal Railroad, pedestrians, and cyclists across the North Branch Canal of the Chicago River. It was constructed in 1901–02 by the Chicago, Milwaukee and St. Paul Railway, and it is a rare example of this type of bridge; it was designated a Chicago Landmark on December 12, 2007.

<span class="mw-page-title-main">Keadby Bridge</span> Bridge

Keadby Bridge, more formally known as the King George V Bridge, crosses the River Trent near Althorpe and Keadby in Lincolnshire, England. It was designed by Alfred Charles Gardner FRSE MIME.

<span class="mw-page-title-main">Rio Vista Bridge</span> Bridge in California, U.S.

The Rio Vista Bridge is a continuous truss span with a vertical-lift bridge in the middle which carries California State Route 12 across the Sacramento River at Rio Vista, California. The present bridge was completed in 1960 and is one of several moveable bridges spanning rivers in the Sacramento–San Joaquin River Delta. It is named after Helen Madere, who served as vice-mayor of Rio Vista. As of 2013 the bridge carries approximately 21,000 cars per day.

<span class="mw-page-title-main">William Donald Scherzer</span> American engineer and inventor

William Donald Scherzer was an American engineer and inventor who invented the rolling lift bridge.

References

  1. 1 2 3 4 5 6 7 Hale, Tom (2007-09-04). "Reconstructing Chicago's North Avenue Bridge". Construction Digest. Archived from the original on February 25, 2008. Retrieved 2008-07-17.
  2. 1 2 3 "New bridge open for traffic". Chicago Tribune . 2008-05-24. Retrieved 2008-06-10.
  3. 1 2 3 4 5 Hess, Jeffrey A. (1999). "North Avenue Bridge, HAER No. IL-154". National Park Service.
  4. 1 2 Madhani, Aamer (2006-06-17). "Bridge to traffic sanity". Chicago Tribune. Retrieved 2006-06-17.
  5. Holth, Nathan. "Historic Bridges of Michigan and Elsewhere - North Avenue Bridge" . Retrieved 2006-10-18.
  6. Thomas, Monifa (2006-06-17). "Mini-Golden Gate to span river at North Avenue: Hybrid suspension bridge will be one of a kind for Chicago". Chicago Sun-Times . Archived from the original on 2018-08-10. Retrieved 2018-08-09.