| PAL-V Liberty | |
|---|---|
 | |
| Role | Flying Car, Roadable aircraft |
| National origin | Netherlands |
| Manufacturer | PAL-V |
| Designer | C. Klok (exterior design) |
| First flight | March 2012 |
| Status | In test |
| Number built | 1 |
The PAL-V Liberty is a combination of a three-wheeled car and an autogyro, or gyroplane under development by PAL-V of the Netherlands. Both a driver's license and an autogyro pilot's license are required to operate the vehicle.
The company settled on a gyroplane design for a number of reasons. "The gyroplane principle not only provides us with a safe and easy-to-operate flying car but it also enables us to make it compact and within existing regulations, which is the most important factor to build a useable flying car," said Mike Stekelenburg, Chief Engineer at PAL-V. [1] Pilots will require a Private pilot licence) with a gyroplane rating to fly the PAL-V Liberty.
On the ground, the propeller and rotor are stopped and power is diverted to the wheels, allowing it to travel as a three-wheeled car, which will enable easier and safer take-off and landing. In addition, it also has a high center of gravity to make it stable in the air by allowing the propeller to act through the vertical center of gravity. In 2005, new technology by Carver provided a solution for the high center of gravity issue. Their Dynamic Curve Stabilizer System ensured the road safety of the 'roadable gyroplane'. [2]
In 2009, PAL-V tested the tilting system with Prototype X1 on the road. After the successful test, PAL-V started to build Prototype X2, also known as the PAL-V ONE. PAL-V made its first flight with the PAL-V ONE in 2012. [3] [4] At that time, the company was seeking funds to develop the type for production.[ citation needed ] The estimated unit price in 2012 was around €300,000. [5] [6] By proving this concept, PAL-V started the design of its first commercial flying car model, based on the proven technologies. [2]
In February 2017, PAL-V started its marketing campaign with the public launch of the PAL-V Liberty and announced that they had started selling the first commercial flying car. The production model was first publicly shown at the Geneva Motor Show in Switzerland on 6 March 2018. [7]
PAL-V has 2 different versions, the Liberty Sport and the Liberty Pioneer. The Sport edition is the base model. The Pioneer edition is the limited edition model. This model will be delivered prior to any other version and includes all available options. Sport prices were expected to start from €300,000 and the Pioneer edition will be €500,000. [8]
After delivering 90 Pioneer Editions, PAL-V will start shipping the Sport Edition. The projected delivery date has been postponed numerous times, and was first expected in the 2010's. As of March 2022 the first delivery was expected to be in 2023. [9] As of August 2024, it has been communicated first delivery will occur 'somewhere in 2026'. [10]
On 9 March, 2020, the company VP, international business development, Carlo Maasbommel, signed a Memorandum of Understanding with the Indian state of Gujarat, to set up a manufacturing and export plant there. At the time the company aimed to export PAL-V from India to the US, the Netherlands, the UK, etc. from 2021. [11]
As of March 2022 the PAL-V Liberty has obtained European Road Admission for road use [12] and agreed the flight certification basis with the European Aviation Safety Agency (EASA). [13] PAL-V is now in the final stage of compliance demonstration, before it can be fully certified and production deliveries begun.
A flying car or roadable aircraft is a type of vehicle which can function both as a road vehicle and as an aircraft. As used here, this includes vehicles which drive as motorcycles when on the road. The term "flying car" is also sometimes used to include hovercars and/or VTOL personal air vehicles. Many prototypes have been built since the early 20th century, using a variety of flight technologies. Most have been designed to take off and land conventionally using a runway. Although VTOL projects are increasing, none has yet been built in more than a handful of numbers.
An autogyro, or gyroplane, is a class of rotorcraft that uses an unpowered rotor in free autorotation to develop lift. While similar to a helicopter rotor in appearance, the autogyro's unpowered rotor disc must have air flowing upward across it to make it rotate.
The Focke-Wulf Fw 61 was the first successful, practical, and fully controllable helicopter, first flown in 1936. It was also known as the Fa 61, as Focke began a new company—Focke-Achgelis—in 1937.
The CarterCopter is an experimental compound autogyro developed by Carter Aviation Technologies in the United States to demonstrate slowed rotor technology. On 17 June 2005, the CarterCopter became the first rotorcraft to achieve mu-1 (μ=1), an equal ratio of airspeed to rotor tip speed, but crashed on the next flight and has been inoperable since. It is being replaced by the Carter Personal Air Vehicle.
The Bensen B-8 is a small, single-seat autogyro developed in the United States in the 1950s. Although the original manufacturer stopped production in 1987, plans for homebuilders are still available as of 2019. Its design was a refinement of the Bensen B-7, and like that aircraft, the B-8 was initially built as an unpowered rotor-kite. It first flew in this form in 1955, and on 6 December a powered version, designated B-8M first flew. The design proved to be extremely popular and long-lasting, with thousands of sets of plans sold over the next thirty years.
A gyrodyne is a type of VTOL aircraft with a helicopter rotor-like system that is driven by its engine for takeoff and landing only, and includes one or more conventional propeller or jet engines to provide thrust during cruising flight. During forward flight the rotor is unpowered and free-spinning, like an autogyro, and lift is provided by a combination of the rotor and conventional wings. The gyrodyne is one of a number of similar concepts which attempt to combine helicopter-like low-speed performance with conventional fixed-wing high-speeds, including tiltrotors and tiltwings.
The Layzell Cricket is a single-seat autogyro produced in the United Kingdom for homebuilding, although it was first produced in the early 1970s fully factory-built. It was a typically minimalist design, featuring a pilot's seat semi-enclosed within a fairing, and a pusher engine and large tailfin located aft of the rotor mast. Forty-three of the original Crickets were built by Campbell Aircraft, with the type enjoying a brief revival in 2001 when it was marketed in kit form by Mike Concannon of Cricket Gyroplanes, before reaching production again in 2005 by Layzell Gyroplanes as the Mk.6.
Expedition Global Eagle was the first attempt in history to circumnavigate the globe using an autogyro. The flight was attempted in 2004 by Warrant Officer Barry Jones using an open-cockpit autogyro which he named Global Eagle. The purpose of the mission was twofold; to set the world record and to raise funds for three charities; the Dyslexia Institute, the NSPCC and the British Red Cross. Jones embarked on his mission on 26 April 2004 from the Museum of Army Flying, Middle Wallop, Hampshire with an honorary military helicopter armada accompanying him during the send off. The expedition was supported by a team of soldiers based at Dishforth, North Yorkshire, United Kingdom.
The Pitcairn PCA-2 was an autogyro developed in the United States in the early 1930s. It was Harold F. Pitcairn's first autogyro design to be sold in quantity. It had a conventional design for its day – an airplane-like fuselage with two open cockpits in tandem, and an engine mounted tractor-fashion in the nose. The lift by the four-blade main rotor was augmented by stubby, low-set monoplane wings that also carried the control surfaces. The wingtips featured considerable dihedral that acted as winglets for added stability.
The Avian 2/180 Gyroplane was a two-seat, single-engine autogyro built in Canada in the 1960s. Several prototypes were built but series production was never achieved.
The Ekin WHE Airbuggy is a British single-seat autogyro designed and built by the W. H. Ekin (Engineering) Company in Northern Ireland.
The Magni M-16 Tandem Trainer is an Italian sport autogyro, seating two in tandem, designed and produced by Magni Gyro srl of Besnate. It and the M-22 Voyager, a touring variant with baggage space and increased endurance, remain in production in 2010 with over 150 sold.
The RotorSport Calidus is a German tandem two-seater autogyro modified in the UK to meet British Civil Airworthiness Requirements CAP643 Section T. The Calidus is an enclosed-cockpit development of the open-cockpit RotorSport UK MT-03. New-build AutoGyro Calidus aircraft are imported from the manufacturers, AutoGyro GmbH in Hildeshem, Germany and completed to British regulations by RotorSport UK Ltd.
The AutoGyro Calidus is a German autogyro, designed and produced by AutoGyro GmbH of Hildesheim. The aircraft is supplied as a complete ready-to-fly-aircraft.
The AutoGyro MT-03 is a German autogyro, designed and produced by AutoGyro GmbH of Hildesheim. The aircraft is supplied as a complete ready-to-fly-aircraft.
The Calumet Snobird Explorer was an American autogyro designed and produced by Calumet Motorsports of Lansing, Illinois, introduced in May 1997. Now out of production, when it was available, the aircraft was supplied as a kit for amateur construction.
The 1933 experimental Pitcairn PA-22 was one of the first wingless autogyros. It was controlled by movement of the rotor plane rather than the usual control surfaces, though initially the much modified lone example retained rudders as a precaution.
The Wilford Gyroplane was based on a German autogyro first flown in 1926. After E. Burke Wilford bought the rights and patents, it was developed in the US until 1936.
ARC Aerosystems is a British consortium that intends to produce modern CAA-certified VTOL autogyros for commercial use. They have a prototype under test, the Pegasus VTOL-Tech, which is to go into production, with delivery expected in 2026. ARC have plans for two other larger gyroplanes, the Linx P3 3-seater, and the Linx P9, a large winged gyroplane.
The Tervamäki ATE-3 is a single-seat autogyro developed in Finland by Jukka Tervamäki and Aulis Eerola in the late 1960s and whose plans were distributed for amateur construction. Other than the designers' own prototype, at least three others were built in Finland and Denmark, The designation stands for Autogyro Tervamäki Eerola, and followed Tervamäki's JT-1 and JT-2 designs. An ATE-3 played a prominent role in a Finnish gangster film of 1969, Leikkikalugangsteri.