PKA (irradiation)

Last updated November 18, 2021

A Primary Knock-on Atom or PKA is an atom that is displaced from its lattice site by irradiation; it is, by definition, the first atom that an incident particle encounters in the target. After it is displaced from its initial lattice site, the PKA can induce the subsequent lattice site displacements of other atoms if it possesses sufficient energy, or come to rest in the lattice at an interstitial site if it does not.

Most of the displaced atoms resulting from electron irradiation and some other types of irradiation are PKAs, since these are usually below the threshold displacement energy and do not have sufficient energy to displace more atoms. In other cases like fast neutron irradiation, most of the displacements result from higher energy PKAs colliding with other atoms as they slow down to rest.^[1]

Collision Models

Atoms can only be displaced if, upon bombardment, the energy they receive exceeds a threshold energy E_d. Likewise, when a moving atom collides with a stationary atom, both atoms will have energy greater than E_d after the collision only if the original moving atom had an energy exceeding 2E_d. Thus, only PKAs with an energy greater than 2E_d can continue to displace more atoms and increase the total number of displaced atoms.^[1] In cases where the PKA does have sufficient energy to displace further atoms, the same truth holds for any subsequently displaced atom.

In any scenario, the majority of displaced atoms leave their lattice sites with energies no more than two or three times E_d. Such an atom will collide with another atom approximately every mean interatomic distance traveled, losing half of its energy during the average collision. Assuming that an atom that has slowed down to a kinetic energy of 1 eV becomes trapped in an interstitial site, displaced atoms will typically be trapped no more than a few interatomic distances away from the vacancies they leave behind.^[1]

There are several possible scenarios for the energy of PKAs, and these lead to different forms of damage. In the case of electron or gamma ray bombardment, the PKA usually does not have sufficient energy to displace more atoms. The resulting damage consists of a random distribution of Frenkel defects, usually with a distance no more than four or five interatomic distances between the interstitial and vacancy. When PKAs receive energy greater than E_d from bombarding electrons, they are able to displace more atoms, and some of the Frenkel defects become groups of interstitial atoms with corresponding vacancies, within a few interatomic distances of each other. In the case of bombardment by fast-moving atoms or ions, groups of vacancies and interstitial atoms widely separated along the track of the atom or ion are produced. As the atom slows down, the cross section for producing PKAs increases, resulting in groups of vacancies and interstitials concentrated at the end of the track.^[1]

Damage Models

A thermal spike is a region in which a moving particle heats up the material surrounding its track through the solid for times of the order of 10⁻¹² s. In its path, a PKA can produce effects similar to those of heating and rapidly quenching a metal, resulting in Frenkel defects. A thermal spike does not last long enough to permit annealing of the Frenkel defects.^[1]^[2]

A different model called the displacement spike was proposed for fast neutron bombardment of heavy elements. With high energy PKAs, the region affected is heated to temperatures above the material's melting point, and instead of considering individual collisions, the entire volume affected could be considered to “melt” for a short period of time. The words “melt” and “liquid” are used loosely here because it is not clear whether the material at such high temperatures and pressures would be a liquid or a dense gas. Upon melting, former interstitials and vacancies become “density fluctuations,” since the surrounding lattice points no longer exist in liquid. In the case of a thermal spike, the temperature is not high enough to maintain the liquid state long enough for density fluctuations to relax and interatomic exchange to occur. A rapid “quenching” effect results in vacancy-interstitial pairs that persist throughout melting and resolidification. Towards the end of the path of a PKA, the rate of energy loss becomes high enough to heat up the material well above its melting point. While the material is melted, atomic interchange occurs as a result of random motion of the atoms initiated by the relaxation of local strains from the density fluctuations. This releases stored energy from these strains that raises the temperature even higher, maintaining the liquid state briefly after most of the density fluctuations disappear. During this time, the turbulent motions continue so that upon resolidification, most of the atoms will occupy new lattice sites. Such regions are called displacement spikes, which, unlike thermal spikes, do not retain Frenkel defects.^[1]^[2]

Based on these theories, there should be two different regions, each retaining a different form of damage, along the path of a PKA. A thermal spike should occur in the earlier part of the path, and this high-energy region retains vacancy-interstitial pairs. There should be a displacement spike towards the end of the path, a low-energy region where atoms have been moved to new lattice sites but no vacancy-interstitial pairs are retained.^[2]

Cascade Damage

The structure of cascade damage is strongly dependent on PKA energy, so the PKA energy spectrum should be used as the basis of evaluating microstructural changes under cascade damage. In thin gold foil, at lower bombardment doses, the interactions of cascades are insignificant, and both visible vacancy clusters and invisible vacancy-rich regions are formed by cascade collision sequences. The interaction of cascades at higher doses was found to produce new clusters near existing groups of vacancy clusters, apparently converting invisible vacancy-rich regions to visible vacancy clusters. These processes are dependent on PKA energy, and from three PKA spectra obtained from fission neutrons, 21 MeV self-ions, and fusion neutrons, the minimum PKA energy required to produce new visible clusters by interaction was estimated to be 165 keV.^[3]

Related Research Articles

Crystallographic defects are interruptions of regular patterns in crystalline solids. They are common because positions of atoms or molecules at repeating fixed distances determined by the unit cell parameters in crystals, which exhibit a periodic crystal structure, are usually imperfect.

Melting, or fusion, is a physical process that results in the phase transition of a substance from a solid to a liquid. This occurs when the internal energy of the solid increases, typically by the application of heat or pressure, which increases the substance's temperature to the melting point. At the melting point, the ordering of ions or molecules in the solid breaks down to a less ordered state, and the solid "melts" to become a liquid.

In physics, sputtering is a phenomenon in which microscopic particles of a solid material are ejected from its surface, after the material is itself bombarded by energetic particles of a plasma or gas. It occurs naturally in outer space, and can be an unwelcome source of wear in precision components. However, the fact that it can be made to act on extremely fine layers of material is utilised in science and industry—there, it is used to perform precise etching, carry out analytical techniques, and deposit thin film layers in the manufacture of optical coatings, semiconductor devices and nanotechnology products. It is a physical vapor deposition technique.

Neutron radiation is a form of ionizing radiation that presents as free neutrons. Typical phenomena are nuclear fission or nuclear fusion causing the release of free neutrons, which then react with nuclei of other atoms to form new isotopes—which, in turn, may trigger further neutron radiation. Free neutrons are unstable, decaying into a proton, an electron, plus an electron antineutrino with a mean lifetime of 887 seconds.

Silver bromide (AgBr), a soft, pale-yellow, water-insoluble salt well known for its unusual sensitivity to light. This property has allowed silver halides to become the basis of modern photographic materials. AgBr is widely used in photographic films and is believed by some to have been used for making the Shroud of Turin. The salt can be found naturally as the mineral bromargyrite.

In crystallography, a vacancy is a type of point defect in a crystal where an atom is missing from one of the lattice sites. Crystals inherently possess imperfections, sometimes referred to as crystalline defects. It is also known as a Schottky defect, although in ionic crystals the concepts are not identical.

The Wigner effect, also known as the discomposition effect or Wigner's disease, is the displacement of atoms in a solid caused by neutron radiation.

Imperfections in the crystal lattice of diamond are common. Such crystallographic defects in diamond may be the result of lattice irregularities or extrinsic substitutional or interstitial impurities, introduced during or after the diamond growth. The defects affect the material properties of diamond and determine to which type a diamond is assigned; the most dramatic effects are on the diamond color and electrical conductivity, as explained by the electronic band structure.

A reactor pressure vessel (RPV) in a nuclear power plant is the pressure vessel containing the nuclear reactor coolant, core shroud, and the reactor core.

A Frenkel defect is a type of point defect in crystalline solids, named after its discoverer Yakov Frenkel. The defect forms when an atom or smaller ion leaves its place in the lattice, creating a vacancy and becomes an interstitial by lodging in a nearby location. In elemental systems, they are primarily generated during particle irradiation, as their formation enthalpy is typically much higher than for other point defects, such as vacancies, and thus their equilibrium concentration according to the Boltzmann distribution is below the detection limit. In ionic crystals, which usually possess low coordination number or a considerable disparity in the sizes of the ions, this defect can be generated also spontaneously, where the smaller ion is dislocated.

Kröger–Vink notation is a set of conventions that are used to describe electric charges and lattice positions of point defect species in crystals. It is primarily used for ionic crystals and is particularly useful for describing various defect reactions. It was proposed by F. A. Kröger and H. J. Vink.

An interstitial defect is a type of point crystallographic defect where an atom of the same or of a different type, occupies a normally unoccupied site in the crystal structure. When the atom is of the same type as those already present they are known as a self-interstitial defect. Alternatively, small atoms in some crystals may occupy interstitial sites, such as hydrogen in palladium. Interstitials can be produced by bombarding a crystal with elementary particles having energy above the displacement threshold for that crystal, but they may also exist in small concentrations in thermodynamic equilibrium. The presence of interstitial defects can modify the physical and chemical properties of a material.

Radiation damage is the effect of ionizing radiation on physical objects. Radiobiology is the study of the action of ionizing radiation on living things, including the health effects of radiation in humans. High doses of ionizing radiation can cause damage to living tissue such as radiation burning and harmful mutations such as causing cells to become cancerous, and can lead to health problems such as radiation poisoning.

Ion beam mixing is the atomic intermixing and alloying that can occur at the interface separating two different materials during ion irradiation. It is applied as a process for adhering two multilayers, especially a substrate and deposited surface layer. The process involves bombarding layered samples with doses of ion radiation in order to promote mixing at the interface, and generally serves as a means of preparing electrical junctions, especially between non-equilibrium or metastable alloys and intermetallic compounds. Ion implantation equipment can be used to achieve ion beam mixing.

A collision cascade is a set of nearby adjacent energetic collisions of atoms induced by an energetic particle in a solid or liquid.

The threshold displacement energy $is the minimum kinetic energy that an atom in a solid needs to be permanently displaced from its lattice site to a defect position. It is also known as "displacement threshold energy" or just "displacement energy". In a crystal, a separate threshold displacement energy exists for each crystallographic direction. Then one should distinguish between the minimum and average over all lattice directions threshold displacement energies. In amorphous solids it may be possible to define an effective displacement energy to describe some other average quantity of interest. Threshold displacement energies in typical solids are of the order of 10 - 50 eV.$

Stopping and Range of Ions in Matter (SRIM) is a group of computer programs which calculate interaction of ions with matter; the core of SRIM is a program Transport of ions in matter (TRIM). SRIM is popular in the ion implantation research and technology community and also used widely in other branches of radiation material science.

The binary collision approximation (BCA) signifies a method used in ion irradiation physics to enable efficient computer simulation of the penetration depth and defect production by energetic ions in solids. In the method, the ion is approximated to travel through a material by experiencing a sequence of independent binary collisions with sample atoms (nuclei). Between the collisions, the ion is assumed to travel in a straight path, experiencing electronic stopping power, but losing no energy in collisions with nuclei.

Radiation materials science describes the interaction of radiation with matter: a broad subject covering many forms of irradiation and of matter.

Neutron embrittlement, sometimes more broadly radiation embrittlement, is the embrittlement of various materials due to the action of neutrons. This is primarily seen in nuclear reactors, where the release of high-energy neutrons causes the long-term degradation of the reactor materials. The embrittlement is caused by the microscopic movement of atoms that are hit by the neutrons; this same action also gives rise to neutron-induced swelling causing materials to grow in size, and the Wigner effect causing energy buildup in certain materials that can lead to sudden releases of energy.

References

1 2 3 4 5 6 "The Displacement of Atoms in Solids by Radiation". Reports on Progress in Physics. 18: 1–51. Bibcode:1955RPPh...18....1K. doi:10.1088/0034-4885/18/1/301.
1 2 3 "On the Nature of Radiation Damage in Metals". Journal of Applied Physics. 25: 961. Bibcode:1954JAP....25..961B. doi:10.1063/1.1721810. hdl: 2027/mdp.39015095100270 .
↑ "Primary knock-on atom energy dependence of cascade damage formation and interaction". Journal of Nuclear Materials. 233–237: 1080–1084. Bibcode:1996JNuM..233.1080S. doi:10.1016/S0022-3115(96)00446-1.