In telecommunications and electrical engineering, a phantom circuit is an electrical circuit derived from suitably arranged wires with one or more conductive paths being a circuit in itself and at the same time acting as one conductor of another circuit.
Phantom circuit derived from two subscriber circuits
A phantom group is composed of three circuits that are derived from two single-channel circuits to form a phantom circuit. Here the phantom circuit is a third circuit derived from two suitably arranged pairs of wires, called side circuits, with each pair of wires being a circuit in itself and at the same time acting as one conductor of the third circuit. The "side circuits" within phantom circuits can be coupled to their respective voltage drops by center-tapped transformers, usually called "repeating coils". The center taps are on the line side of the side circuits. Current from the phantom circuit is split evenly by the center taps. This cancels crosstalk from the phantom circuit to the side circuits.
Diagram showing how the phantom currents (red) cancel in the transformer. Side circuit currents (blue) do not cancel and are transmitted through the transformer.
Phantom working increased the number of circuits on long-distance routes in the early 20th century without putting up more wires.[citation needed] Phantoming declined with the adoption of carrier systems.[citation needed]
It is theoretically possible to create a phantom circuit from two other phantom circuits and so on up in a pyramid with a maximum 2n-1 circuits being derived from n original circuits. However, more than one level of phantoming is usually impractical. Isolation between the phantom circuit and the side circuits relies on accurate balance of the line and transformers. Imperfect balance results in crosstalk between the phantom and side circuits and this effect accumulates as each level of phantoms is added. Even small levels of crosstalk are unacceptable on analogue telecommunications circuits since speech crosstalk is still intelligible down to quite low levels.
Condenser microphones have impedance converter (current amplifier) circuitry that requires powering; in addition, the capsule of any non-electret, non-RF condenser microphone requires a polarizing voltage to be applied. Since the mid- to late 1960s most balanced, professional condenser microphones for recording and broadcast have used phantom powering.[citation needed] It can be provided by outboard AC or battery supplies, but nowadays[when?] is most often built into the mixing console, recorder or microphone preamplifier to which the microphones are connected.
the most common circuit uses +48 V DC fed through a matched pair of 6.8 kΩ resistors for each input channel.[citation needed] This arrangement has been standardized by the IEC and ISO, along with a less-commonly-used arrangement with +12 V DC and 680 Ω feed resistors.
As a practical matter, phantom powering allows the same two-conductor shielded cables to be used for both dynamic microphones and condenser microphones, while being harmless to balanced microphones that aren't designed to consume it, since the circuit balance prevents any substantial DC from flowing through the output circuit of those microphones.
Simple DC signalling can be achieved on a telecommunications line in a similar way to phantom powering of microphones. A switch connected to the transformer centre-tap at one end of the line can operate a similarly connected relay at the other end. The return path is through the ground connection. This arrangement can be used for remotely controlling equipment.
Carrier circuit phantoms
From the 1950s to around the 1980s, using phantoms on star-quad trunk carrier circuits was a popular method of deriving a high quality broadcast audio circuit. The multiplexed FDM telecommunications carrier system usually did not use the baseband of the cable because it was inconvenient to separate low frequencies with filters. On the other hand, a one-way audio phantom could be formed from the two pairs (go and return signals) making up the star-quad cable.
Unloaded phantom
Unloaded phantom configuration. The windings of the loading coil are wound such that the magnetic flux induced in the core is normally in the same direction for both windings. However, in the phantom configuration the flux cancels.
Unloaded phantom is a phantom configuration of loaded lines (a circuit fitted with loading coils). The idea here is not to create additional circuits. Rather, the purpose is to cancel or greatly reduce the effect of the loading coils fitted to a line. The reason for doing this is that loaded lines have a definite cut-off frequency and it may be desired to equalise the line to a frequency which is higher than this, for example to make a circuit suitable for use by a broadcaster. Ideally, the loading would be removed or reduced for a permanent connection, but this is not feasible for temporary arrangements such as a requirement for outside broadcast. Instead, two circuits in a phantom configuration can be used to greatly reduce the inductance being inserted by the loading coils, and hence the loading effect.
Diagram showing how the flux due to the phantom currents (red) is cancelled in the load coil. Flux due to normal line currents (blue) is additive.
It works because the loading coils used on balanced lines have two windings, one for each leg of the circuit. They are both wound on a common core and the windings are so arranged that the magnetic flux induced by both of them is in the same direction. Both windings induce an emf in each other as well as their own self-induction. This effect greatly increases the inductance of the coil and hence its loading effectiveness. By contrast, when the circuit is in the phantom configuration the currents in the two wires of each pair are in the same direction and the magnetic flux is being cancelled. This has precisely the opposite effect and the inductance is greatly reduced.
This configuration is most commonly used on the two pairs of a star-quad cable. It is not so successful with other pairs of wires. The difference in the path of the two pairs can easily destroy the balance and results in crosstalk and interference.
This configuration can also be called "bunched pairs". However, "bunched pairs" can also refer to the straightforward connection of two lines in parallel which is not a phantom circuit and will not reduce the loading.
See also
Bridge circuit - a closely related concept; the operation of a phantom circuit depends on it being a kind of balanced bridge
Single-wire earth return - power transmission using one wire and the Earth as a return conductor
In electrical engineering, a transformer is a passive component that transfers electrical energy from one electrical circuit to another circuit, or multiple circuits. A varying current in any coil of the transformer produces a varying magnetic flux in the transformer's core, which induces a varying electromotive force (EMF) across any other coils wound around the same core. Electrical energy can be transferred between separate coils without a metallic (conductive) connection between the two circuits. Faraday's law of induction, discovered in 1831, describes the induced voltage effect in any coil due to a changing magnetic flux encircled by the coil.
Three-phase electric power is a common type of alternating current (AC) used in electricity generation, transmission, and distribution. It is a type of polyphase system employing three wires and is the most common method used by electrical grids worldwide to transfer power.
In telecommunications and professional audio, a balanced line or balanced signal pair is an electrical circuit consisting of two conductors of the same type, both of which have equal impedances along their lengths, to ground, and to other circuits. The primary advantage of the balanced line format is good rejection of common-mode noise and interference when fed to a differential device such as a transformer or differential amplifier.
A loading coil or load coil is an inductor that is inserted into an electronic circuit to increase its inductance. The term originated in the 19th century for inductors used to prevent signal distortion in long-distance telegraph transmission cables. The term is also used for inductors in radio antennas, or between the antenna and its feedline, to make an electrically short antenna resonant at its operating frequency.
Twisted pair cabling is a type of communications cable in which two conductors of a single circuit are twisted together for the purposes of improving electromagnetic compatibility. Compared to a single conductor or an untwisted balanced pair, a twisted pair reduces electromagnetic radiation from the pair and crosstalk between neighbouring pairs and improves rejection of external electromagnetic interference. It was invented by Alexander Graham Bell.
Balanced audio is a method of interconnecting audio equipment using balanced interfaces. This type of connection is very important in sound recording and production because it allows the use of long cables while reducing susceptibility to external noise caused by electromagnetic interference. The balanced interface guarantees that induced noise appears as common-mode voltages at the receiver which can be rejected by a differential device.
A balun is an electrical device that allows balanced and unbalanced lines to be interfaced without disturbing the impedance arrangement of either line. A balun can take many forms and may include devices that also transform impedances but need not do so. Sometimes, in the case of transformer baluns, they use magnetic coupling but need not do so. Common-mode chokes are also used as baluns and work by eliminating, rather than rejecting, common mode signals.
Phantom power, in the context of professional audio equipment, is DC electric power equally applied to both signal wires in balanced microphone cables, forming a phantom circuit, to operate microphones that contain active electronic circuitry. It is best known as a convenient power source for condenser microphones, though many active direct boxes also use it. The technique is also used in other applications where power supply and signal communication take place over the same wires.
In electronics, a center tap (CT) is a contact made to a point halfway along a winding of a transformer or inductor, or along the element of a resistor or a potentiometer.
Two-phase electrical power was an early 20th-century polyphase alternating current electric power distribution system. Two circuits were used, with voltage phases differing by one-quarter of a cycle, 90°. Usually circuits used four wires, two for each phase. Less frequently, three wires were used, with a common wire with a larger-diameter conductor. Some early two-phase generators had two complete rotor and field assemblies, with windings physically offset to provide two-phase power. The generators at Niagara Falls installed in 1895 were the largest generators in the world at that time, and were two-phase machines. Three-phase systems eventually replaced the original two-phase power systems for power transmission and utilization. Active two-phase distribution systems remain in Center City Philadelphia, where many commercial buildings are permanently wired for two-phase, and in Hartford, Connecticut.
In electrical engineering, an autotransformer is an electrical transformer with only one winding. The "auto" prefix refers to the single coil acting alone. In an autotransformer, portions of the same winding act as both the primary winding and secondary winding sides of the transformer. In contrast, an ordinary transformer has separate primary and secondary windings that are not connected by an electrically conductive path. between them.
A current transformer (CT) is a type of transformer that is used to reduce or multiply an alternating current (AC). It produces a current in its secondary which is proportional to the current in its primary.
A pickup is a transducer that captures or senses mechanical vibrations produced by musical instruments, particularly stringed instruments such as the electric guitar, and converts these to an electrical signal that is amplified using an instrument amplifier to produce musical sounds through a loudspeaker in a speaker enclosure. The signal from a pickup can also be recorded directly.
Differential signalling is a method for electrically transmitting information using two complementary signals. The technique sends the same electrical signal as a differential pair of signals, each in its own conductor. The pair of conductors can be wires in a twisted-pair or ribbon cable or traces on a printed circuit board.
Transposition is the periodic swapping of positions of the conductors of a transmission line, in order to reduce crosstalk and otherwise improve transmission. In telecommunications this applies to balanced pairs whilst in power transmission lines three conductors are periodically transposed.
A Scott-T transformer or Scott connection is a type of circuit used to produce two-phase electric power from a three-phase source, or vice versa. The Scott connection evenly distributes a balanced load between the phases of the source. The Scott three-phase transformer was invented by Westinghouse engineer Charles F. Scott in the late 1890s to bypass Thomas Edison's more expensive rotary converter and thereby permit two-phase generator plants to drive three-phase motors.
Various types of electrical transformer are made for different purposes. Despite their design differences, the various types employ the same basic principle as discovered in 1831 by Michael Faraday, and share several key functional parts.
In electrical engineering, a balanced circuit is electronic circuitry for use with a balanced line, or the balanced line itself. Balanced lines are a common method of transmitting many types of electrical signals between two points on two wires. In a balanced line, the two signal lines are of a matched impedance to help ensure that interference, induced in the line, is common-mode and can be removed at the receiving end by circuitry with good common-mode rejection. To maintain the balance, circuit blocks which interface to the line or are connected in the line must also be balanced.
In electrical engineering, star-quad cable is a four-conductor electrical cable that has a special quadrupole geometry which provides magnetic immunity when used in a balanced line. Four conductors are used to carry the two legs of the balanced line. All four conductors must be an equal distance from a common point. The four conductors are arranged in a four-pointed star. Opposite points of the star are connected together at each end of the cable to form each leg of the balanced circuit.
This glossary of electrical and electronics engineering is a list of definitions of terms and concepts related specifically to electrical engineering and electronics engineering. For terms related to engineering in general, see Glossary of engineering.
This page is based on this Wikipedia article Text is available under the CC BY-SA 4.0 license; additional terms may apply. Images, videos and audio are available under their respective licenses.
