Prussian S 10

Last updated

The Prussian Class S 10 included all express train locomotives in the Prussian state railways that had a 4-6-0 wheel arrangement. There were four sub-classes: the S 10, S 10.1 (with 1911 and 1914 variants) and S 10.2.

Contents

Prussian S 10

Prussian S 10
DRG Class 17.0–1
SNCB Type 60
S10 Breslau 1008.jpg
Type and origin
Builder Berliner Maschinenbau AG
Build date1910–1914
Total produced202
Specifications
Configuration:
   Whyte 4-6-0
Gauge 1,435 mm (4 ft 8+12 in)
Leading dia. 1,000 mm (39.4 in)
Driver dia.1,980 mm (78.0 in)
Length:
  Over beams20,750 mm (68 ft 1 in)
Axle load 17.5 t (39,000 lb)
Adhesive weight 50.9 t (112,000 lb)
Service weight77.2 t (170,000 lb)
Water cap.21.5 m3 (5,700 US gal), 31.5 m3 (8,300 US gal)
Boiler pressure14 bar (1.4 MPa)
Heating surface:
  Firebox2.86 m2 (4,430 in²)
  Evaporative153.09 m2 (1,647.8 ft²)
Superheater:
  Heating area61.50 m2 (662.0 ft²)
Cylinders 4
Cylinder size 430 mm (16.93 in)
Piston stroke 630 mm (24.80 in)
Performance figures
Maximum speed110 km/h (68 mph)
Indicated power861 kW (1,155 hp)
Career
NumbersDRG 17 001–135
Retired1954

As a result of the lack of powerful express locomotives in the first decade of the 20th century, the Prussian state railways ordered the Class S 10 locomotives from Schwartzkopff. This engine was an evolutionary development of the passenger train locomotive, the Prussian P 8, which can be seen from the similarity in their locomotive frames. Unlike the P 8, however, the S 10—inspired by the Saxon XII H—had a four-cylinder engine with simple expansion.

Between 1910 and 1914 a total of 202 locomotives were built. The two prototypes were initially designated as S 8 class and only reclassified in 1912 to S 10. The Lübeck-Büchen Railway took delivery of five similar, albeit somewhat less powerful, machines that they also designated as the S 10.

Over the course of time several modifications were made. In the end the S 10 proved to be worse than the S 101, a four-cylinder compound locomotive in terms of both steam and coal consumption and was one of the most uneconomical Prussian locomotives.

The Deutsche Reichsbahn took over 135 locomotives into its Class 17.0-1 and gave them the running numbers 17 001–135. They were retired by 1935, however, due to their high fuel consumption. Only three examples (17 039, 102 and 107) survived the Second World War, as braking locomotives. The last S 10 was retired in 1954.

Number 17 008 has been sectioned and is on display in the German Museum of Technology in Berlin .

The S 10s were coupled with tenders of classes pr 2'2' T 21.5 and pr 2'2' T 31.5.

Prussian S 10.1 (1911 variant)

Prussian S 10.1 - 1911 variant
(Prussia, Alsace-Lorraine)
DRG Class 17.10–11
ÖBB Class 617
Locomotive 17 1055.jpg
Prussian S10.1 as "Osten 1135" on 17.5.1993 in Potsdam
Type and origin
Builder Henschel
Build date1911–1914
Total produced152
Specifications
Configuration:
   Whyte 4-6-0
Gauge 1,435 mm (4 ft 8+12 in)
Leading dia. 1,000 mm
Driver dia.1,980 mm
Length:
  Over beams21,110 mm
Axle load 17.8 t
Adhesive weight 53.2 t
Service weight83.1 t
Water cap.21.5/31.5 m3
Boiler pressure15 bar (1.5 MPa)
Heating surface:
  Firebox3.18 m2
  Evaporative161.22 m2
Superheater:
  Heating area58.50 m2
Cylinders 4
Cylinder size 2×400/610 mm
Piston stroke 660 mm
Performance figures
Maximum speed120 km/h
Indicated power1,044 kW
Career
NumbersDRG 17 1001–1123, 1145–1153
Retired1963

Even as production started on the S 10, Henschel were given an order for the manufacture of a compound locomotive, which promised to deliver lower coal consumption.

This locomotive, classified as the S 10.1, was not based on the S 10, but was a new design. The four-cylinder compound engine was of the de Glehn type, which meant that the outside cylinders, set well to the rear, drove the second coupled axle and the inside cylinder drove the first. The engines were larger and more powerful than the S 10 and, thanks to their compound engines, also more economical.

Between 1911 and 1914, no less than 135 examples were built for Prussia and 17 for Alsace-Lorraine. Following initial dissatisfaction with the vehicles, several modifications to the locomotives finally led to the desired success. For example, no feedwater preheater was fitted to start with for weight-saving reasons, but one was later installed. The remaining disadvantages, such as the poor accessibility of the inside drive, led to the development of a new version in the shape of the 1914 variant.

After three locomotives were sent abroad as reparations, the Deutsche Reichsbahn took over the remaining 132 vehicles as Class 17.10–11 with numbers 17 1001–1123 and 17 1145–1153.

The three locomotives left in 1945 with the Austrian Federal Railway were renumbered to 617.1004, 617.1089 and 617.1099 and retired in 1957.

The Deutsche Bundesbahn withdrew their last S 10.1 engines in 1952. The Deutsche Reichsbahn in East Germany held onto these locomotives for longer and converted 13 examples to coal-dust firing. Locomotive number 17 1119 was given a condensing tender. In 1963 the last machines were taken out of service by the DR.

Number 17 1055 (formerly "Posen 1107", running as "Osten 1135") was partly returned to its original configuration and belongs today to the Dresden Transport Museum.

The S 10.1s were equipped with tenders of Prussian classes pr 2'2' T 21.5 and pr 2'2' T 31.5.

Prussian S 10.1 (1914 variant)

Prussian S 10.1 - 1914 variant
DRG Class 17.11–12
SNCB Type 61
S10 1 1914.jpg
Type and origin
Builder Henschel
Build date1914ff.
Total produced109
Specifications
Configuration:
   Whyte 4-6-0
Gauge 1,435 mm (4 ft 8+12 in)
Leading dia. 1,000 mm
Driver dia.1,980 mm
Length:
  Over beams17,670 mm
Axle load 17,7 t
Adhesive weight 52.0 t
Service weight84.2 t
Boiler pressure15 bar (1.5 MPa)
Heating surface:
  Firebox2.95 m2
  Evaporative161.22 m2
Superheater:
  Heating area52.10 m2
Cylinders 4
Cylinder size 2×400/610 mm
Piston stroke 660 mm
Performance figures
Maximum speed110 km/h
Indicated power> 1,100 kW
Career
NumbersDRG 17 1124–1144, 1154–1209
Retired1964

Various disadvantages of the 1911 variant of the S 10.1, such as the difficulty of accessing the inside driving gear and the long steam lines between high and low-pressure cylinders, caused the Prussian state railways to have the design reworked.

The four cylinders were now located – as on the von Borries compound – on a slant; the twin-axle drive configuration was however retained. Even the boiler was modified; grate and firebox heating areas and the superheater were increased in size. Due to the altered location of the cylinders the running plate could be raised, which gave the locomotives a higher and more modern appearance, although in fact the height of the boiler axis above the rails remained unchanged.

In spite of these considerable differences, the 1914 variant was also designated as the S 10.1. These locomotives were the most powerful expresses in Prussia, and the Prussian state railways continued to live without Pacific locomotives. In 1914, one locomotive reached a speed of 152 km/h on a trial run with three coaches (according to some sources it may even have reached 156 km/h).

The Deutsche Reichsbahn took over 77 locomotives as Class 17.11-12 with the numbers 17 1124–1144 and 1154–1209.

In the DR in the GDR two 1914 variant locomotives were given Wendler coal-dust firing. The last engine was retired in 1964. Unlike the 1911 variant, no 1914 variant of this locomotive class remains preserved.

Prussian S 10.2

Prussian S 10.2
DRG Class 17.2
SNCB Type 62
S10 2.jpg
Type and origin
Builder Vulcan
Build date1914ff.
Total produced124
Specifications
Configuration:
   Whyte 4-6-0
Gauge 1,435 mm (4 ft 8+12 in)
Leading dia. 1,000 mm
Driver dia.1,980 mm
Length:
  Over beams21,200 mm
Axle load 17.8 t
Adhesive weight 53.4 t
Service weight80.9 t
Water cap.31.5 m3
Boiler pressure14 bar (1.4 MPa)
Heating surface:
  Firebox2.86 m2
  Evaporative153.09 m2
Superheater:
  Heating area61.50 m2
Cylinders 3
Cylinder size 500 mm
Piston stroke 630 mm
Performance figures
Maximum speed120 km/h
Indicated power883 kW
Career
NumbersDRG 17 201–296
Retired1948

The Stettiner Maschinenbau AG Vulcan built the Class S 10.2 based on the S 10. In contrast to the S 10 it only had three cylinders, but was otherwise largely identical.

The Prussian state railways bought a total of 124 locomotives from 1914. These variants were certainly superior to the S 10, but not the S 10.1.

28 engines had to be handed to foreign railway administrations after the First World War. The Deutsche Reichsbahn took over the remaining 96 vehicles, incorporating them into Class 17.2 with running numbers 17 201–296. The remaining engines were gathered together into the northern and central German Reichsbahn railway divisions. Here they were partly replaced from 1930 by the Class 03.

88 engines survived the Second World War and ended up with the Deutsche Bundesbahn, where they were retired by 1948.

The S 10.2s were equipped with pr 2'2' T 31.5 tenders.

Trial locomotives

Three S 10.2s were fitted with Stumpf parallel-flow cylinders (Gleichstromzylinder) for test purposes, whereby unlike the production models, the outer cylinders drove the second coupled axle. Even when they were converted to the standard configuration, the twin-axle drive was retained. One of these engines went to Poland after the First World War; the others were given numbers 17 203 and 17 204 by the Deutsche Reichsbahn.

In 1925, locomotive 17 206 was given a Schmidt-Hartmann high-pressure boiler with a boiler overpressure of 5.884 MPa (58.84 bar), and the drive was converted to a compound configuration. The increased performance of the H 17 206 designated locomotive compared with the production design did not justify the higher construction costs however; the engine was converted back to the standard design in 1929 and retired in 1936.

The two locomotives with running numbers 17 236 and 17 239 were given a medium-pressure boiler in 1933 with a boiler overpressure of 2.452 MPa (24.52 bar), and they were also converted to compound operation at the same time. The performance of these converted engines matched that of the DRG Class 03 and they were employed together with the Class 03s in scheduled services. After several cases of boiler damage, however the boiler pressure, had to be reduced to 16 bar (1.6 MPa) in order to avoid further problems. During the 1930s the two medium-pressure locomotives were reconverted again. Both engines survived the ware and were retired together with the other S 10.2s in 1948.

See also

Sources

Related Research Articles

<span class="mw-page-title-main">DRG Class 01</span> Class of 241 German 4-6-2 locomotives (1926–1982)

The Deutsche Reichsbahn-Gesellschaft's BR 01 steam locomotives were the first standardised (Einheitsdampflokomotive) steam express passenger locomotives built by the unified German railway system. They were of 4-6-2 "Pacific" wheel arrangement in the Whyte notation, or 2′C1′ h2 in the UIC classification. The idea of standardisation was that it would reduce maintenance costs; i.e. if a BR 01 whose engine shop was in, say, Berlin broke down in Dresden, instead of having to ship the necessary part from Berlin and take the locomotive out of service, a part from the Dresden shop could be used as all of the engines, parts, and workings were exactly the same and produced nationwide. Thus it was a "standard" product for engine shops.

<span class="mw-page-title-main">Prussian S 3</span>

The Prussian Class S 3s were saturated steam locomotives developed by Hanomag for the Prussian state railways and were built from 1893.

<span class="mw-page-title-main">Bavarian S 3/6</span>

The Class S 3/6 steam locomotives of the Royal Bavarian State Railways were express train locomotives with a 4-6-2 Pacific or 2'C1' wheel arrangement.

The Class S 3/5 engines of the Royal Bavarian State Railways were express train steam locomotives with a 4–6–0 wheel arrangement.

<span class="mw-page-title-main">Prussian G 8.1</span>

The Prussian G 8.1 was steam locomotive operated by the Prussian state railways. It was a heavier, stronger development of the G 8 and was initially referred to as a 'strengthened standard class'.

<span class="mw-page-title-main">Einheitsdampflokomotive</span>

The Einheitsdampflokomotiven, sometimes shortened to Einheitslokomotiven or Einheitsloks, were the standardized steam locomotives built in Germany after 1925 under the direction of the Deutsche Reichsbahn-Gesellschaft. Their manufacture made extensive use of standard design features and components.

<span class="mw-page-title-main">Prussian G 12</span>

The Prussian G 12 is a 1'E 2-10-0 goods train locomotive built for the Prussian state railways.

<span class="mw-page-title-main">Prussian G 10</span>

The Prussian G 10 was a German goods train, steam locomotive, whose design was based on a combination of the running and valve gear from the Prussian T 16 and the boiler from the Prussian P 8. In developing the G 10, however, the T 16 running gear with side play on the first and fifth axles was modified. The T 16 was also subsequently built with this modified configuration and called the Prussian T 16.1. The G 10 was intended for heavy goods train duties on main lines, but as a result of its low axle load it could be employed more flexibly than its equally powerful cousin, the Prussian G 8.1. The G 10 was occasionally even used in passenger train service.

The Prussian G 12.1 was a German steam locomotive built for the Prussian state railways during the First World War and was the largest Prussian freight locomotive with a 2-10-0 wheel arrangement. It had three cylinders, the two outer ones driving the third axle and the inner one the second axle.

<span class="mw-page-title-main">DR Class 58.30</span>

After the Second World War, the Deutsche Reichsbahn in East Germany had a requirement for powerful goods train locomotives with a 15-18 tonne axle load for routes in the Mittelgebirge, the mountainous areas in the south of the country. As a result, the DR Class 58.30 emerged, as part of the so-called 'reconstruction programme', based on rebuilds of the former Prussian G 12 locomotives. Between 1958 and 1962, 56 locomotives, originally from various state railways were converted at the former repair shop, RAW Zwickau.

The Saxon Class XVIII was a German six-coupled tender locomotive built for the Royal Saxon State Railways in 1917/18 for express train services. The Deutsche Reichsbahn grouped them in 1925 into DRG Class 18.0.

<span class="mw-page-title-main">Prussian S 6</span>

The Prussian S 6 was a class of German steam locomotive with a 4-4-0 wheel arrangement operated by the Prussian state railways for express train services.

<span class="mw-page-title-main">Prussian P 6</span>

The Prussian Class P 6s were passenger locomotives operated by the Prussian state railways with a leading axle and three coupled axles.

The Prussian S 9 was an express steam locomotive with the Prussian state railways, first built in 1908. It had a 4-4-2 (Atlantic) wheel arrangement and a four-cylinder compound engine. It was developed by the firm of Hanomag in Hanover who delivered a total of 99 engines of this class.

The Royal Saxon State Railways designated four-coupled, Atlantic (4-4-2) express locomotives as Class X and the Deutsche Reichsbahn subsequently grouped these locomotives into DRG Class 14.2 in 1925.

<span class="mw-page-title-main">Prussian T 3</span>

The Prussian Class T 3 steam locomotives procured for the Prussian state railways were 0-6-0 tank locomotives. Together with the Prussian T 2 they were the first locomotives that were built to railway norms. The first units were delivered by Henschel in 1882.

<span class="mw-page-title-main">Prussian G 8</span> Prussian locomotive

The Prussian Class G 8 locomotives were eight-coupled, superheated, freight locomotives operated by the Prussian state railways. There were two variants: the G 8 built from 1902 with a 14 tonne axle load and the "reinforced G 8" built from 1913 with a 17-tonne axle load. The latter was the most numerous German state railway (Länderbahn) locomotive, over 5,000 examples being built.

The Prussian G 8.2 class of locomotives actually incorporated two different locomotive types: one was the Prussian/Oldenburg G 8.2, for which the Deutsche Reichsbahn subsequently issued follow-on orders; the other was the G 8.2 of the Lübeck-Büchen Railway.

<span class="mw-page-title-main">Saxon VIII V2</span>

The Saxon Class VIII 2 was a twin-coupled tender locomotive procured for passenger services by the Royal Saxon State Railways. In 1925, the Deutsche Reichsbahn grouped these engines into their Class 36.9-10.